Search Documents

By Michael Gauna, William J. Gray, Joseph C. Zelanko

Mechanized mining in the underground coal industry has continued to evolve since the introduction of the remote control mining machine. Remote control continuous mining machines without an onboard operator’s compartment are now the norm in the industry. Extended cuts in excess of 30 ft (9.1 m) are commonplace. Unfortunately, machine operator positioning has become an often unrecognized safety concern, particularly when remote control continuous mining machines excavate a turn (turn a crosscut). From January 2001 through July 2004, remote control continuous mining machine operators or helpers have been involved in ten roof fall fatalities and eight machinery crushing fatalities. The machinery crushing incidents occurred when machines were being repositioned or moved to another place. Of the ten roof fall fatalities, three occurred while a crosscut was being turned and a fourth fatality occurred while mining was being conducted adjacent to the crosscut. The operating time associated with turning crosscuts is a relatively small part of the mining cycle. In recent years, however, a disproportionate number of fatal incidents appear to have been associated with this activity. Procedures for reducing the incidence of operator fatalities while turning crosscuts are discussed. These techniques include: minimizing the number of turn cuts, limiting turn cut depth, establishing no work zones and using visual warning devices to designate them, installing more roof/rib support in the vicinity of the turn cut, using notch cuts prior to initiating a full turn cut, and positioning the remote control miner operator in nontraditional locations.

Jan 1, 2005

By Daniel L. Hanson

This paper presents case histories of the construction of four large diameter circular shafts using reinforced concrete ring beams as the primary internal support system. The case histories pertain to concrete ring beam systems which have been successfully used in shafts up to 130 feet in diameter and 75 feet deep. Soldier pile and lagging, and driven steel piling earth retaining systems using ring beams, are discussed together with the cost savings associated with using concrete ring beams. Soil conditions encountered at the case history sites are discussed together with the development of design criteria for each shaft. Instrumentation data obtained at one site are also presented.

Jan 1, 1987

By S. P. Banerjee

By international standards, Indian coal seams are not very gassy. In some of the major coalfields such as Singareni, Wardha, Pench, Chirimiri, Rewa and Talcher Coalfields practically no methane is emitted from the coal seams. Even in the coalfields of Ranigang, Jharia, Bokaro and Karanpura, all of which are situated in the basin of the Damodar river, only a few mines are faced with excessive gas emission problems. But the number of such mines is increasing as deeper reserves are being worked and already the exploitation of some of the best quality coal reserves in the country is held up pending measures for control of methane emission in these mines. Even in mines having no previous history of gas emission, methane has been met near dykes and faults. This was dramatically revealed by an explosion in Dhori colliery in 1965 wherein 268 persons got killed. Until that time, Dhori colliery was considered as a non-gassy mine but on that fateful day gas came to the workings through a freshly exposed fault plane. Similar incidences of ignition of firedamp in so-called non-gassy mines have also occured in the past, for example, in Chapui Khas and Samla Dalurband collieries, but the casualty figures were not as high. After the Dhori explosion, all Indian coal seams have been declared to be gassy, whether presence of methane is detected in the workings or not.

Jan 1, 1980

Separation of dolomite from Florida phosphates was achieved by first conditioning the feed with fatty acid at pH 10 followed by reconditioning at pH 4 or below, before flotation. Observed selectivity of this two stage conditioning process was attributed to the amount as well as changes in the nature of the adsorbed collector species upon reconditioning. In this paper, bench scale flotation results of optimizing the major process parameters, such as reconditioning pH and collector dosage, for upgrading natural high dolomitic phosphate samples from Florida are discussed.

Jan 1, 1988

By R. Flattery, Z. Agioutantis

Coal and rock pillar design is critical not only for mineral extraction but also for the safety of the mine operators. Pillar strength can be estimated through numerous empirical formulas that are available in the literature, which are typically based on a statistical analysis of case study data. The limitation of most of these equations is that they only considered the width to height ratio and in situ rock or coal strength for pillars in horizontal seams. The adoption of such equations to estimate pillar strength in inclined seams may overestimate the pillar strength and ultimately lead to a poor pillar design. This paper will discuss different techniques that can be used to estimate pillar strength in inclined seams as well as present preliminary modeling results for stress redistribution around inclined pillars. Factors in the parametric analysis include pillar shapes, geometry, and seam inclination.

Mar 2, 2022

By Kal V. S. Sastry

Modeling and simulation are two major tools available to a mineral process engineer for a consistent and systematic process analysis. The application of these tools to the analysis of specific mineral processing unit operations is well documented in the literature; nevertheless, they are used only to a limited extent in the industry. This is because the fundamental principles of modeling and simulation in the context of mineral processing context are not available. This paper represents the first in a series of papers planned to meet this need. General principles of process modeling and a unified mineral process model development methodology are presented. A simple example of model development using the flotation unit operation is given. A discussion of the practical significance, challenges and opportunities associated with mineral process modeling is included.

Jan 1, 1990

By D. Murray

"The Mine Improvement and New Emergency Response (MINER) Act included the need for improved chemical technologies to address respiratory protective device inadequacies and refuge alternative development. The National Institute for Occupational Safety and Health’s (NIOSH) National Personal Protective Technology Laboratory (NPPTL) invests in research and development to improve the carbon dioxide (CO2) scrubbing technologies built into these mine safety systems. Testing at NIOSH NPPTL is performed using a custom-designed test system containing a chemical reactor and sensors in a constant flow of simulated expired breath to evaluate chemical performance for the scrubber materials. Current testing procedures focus on device duration or capacity, but do not report criteria needed to effectively optimize chemical performance. In this presentation, testing results which identify the chemical performance roles for CO2 scrubber components will be reported, and specific component chemical activities will be linked to both duration and CO2 absorption capacities. Chemical components being evaluated include hydroxyl, superoxides, metal, and amine active sites, distributed in salts, zeolites, metal-organic frameworks, and microporous materials. INTRODUCTION CO2 absorbents and oxygen sources are at the heart of closed circuit breathing air supply systems used in mining escape and rescue operations. CO2 absorbent technology was first developed for diving rebreathers and has been in use for over a century. Typically these devices include a soda lime formulation of pellets in the 8-12 mesh range. Larger 4-8 mesh particles are used in medical grade “low-flow” applications, since these particles present a lower flow resistance regime more amenable for use with resting individuals. Potassium superoxide and lithium hydroxide formulations are also used, where in each case the formulations involve bulk solid pellets or materials affixed to surfaces. CO2 capture technologies are now under intensive study in the energy and automotive industries, where the pursuit of optimal combustion processes has led to the development of new materials to capture, convert and store CO2, oxygen and carbon monoxide gases. Recent advances in nano-structured and high surface area catalysis have produced novel materials demonstrating chemical performance improvements in these industries, and these improvements may now also be adapted to enhance chemical efficiency and performance in escape and rescue devices. Higher surface area materials offer promise for improving the efficiency, or decreasing the burdens associated with the use of closed circuit respiratory protective devices containing CO2 absorbents. Novel chemicals that display advantages in chemical performance or decreased burden will be examined for inclusion in developing systems such as the next-generation closed-circuit mining escape respirator or refuge alternatives."

Jan 1, 2018

By A. G. Wylie

The dimensions and shape of both airborne and bulk amphibole-asbestos fibers are different from those of cleavage fragments of the amphiboles. These differences are related to the mineralogical properties unique to the habit of asbestos. These properties include the fibrillar structure, small fibrill widths and distinctive crystallographic faces of fibrills. Criteria for distinguishing amphibole cleavage fragments from amphibole-asbestos include mineralogical proper-ties observable in bulk samples and the dimensions of particles collected on air filters.

Jan 1, 1988

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter?s dust collection system. The laboratory tests evaluated the bag?s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector?s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector?s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

Jan 1, 2008

By M. Misra

The interaction of xanthate with SO2 in the flotation of sphalerite and chalcopy.ite is discussed. 'The SO depression of sphaledte is due to the decomposition reaction of xanthate by SO2 The decomposition reaction is dependent on the cole ratios of xanthate/SO2, oxygen concentration and pH. Xanthate adsorbs at a faster rate by chalcopyrite than sphalerite. The faster rate of xanthate adsorption by chalcopyrite and the specific action of S02 on the surface of chalcopy.ite facilitate the selective separation of chalcopyrite from sphaledte.

Jan 1, 1989

By S. K. Kawatra, T. C. Eisele

Microorganisms, such as the bacteria Thiobacillus ferrooxidans, have been reported to depress pyrite flotation (Elzeky and Attia, 1987; Atkins, 1990). However, the depen¬dence of the depression on the type of organism or on suspension pH is still being determined. In this study, the relative effectiveness of various microorganisms (chemolithotrophic bacteria, chemoorganotrophic bacteria and yeast) over the pH range of 2 to 12 was studied. Screen¬ing tests using microflotation showed that every microorgan¬ism tested was capable of depressing naturally hydrophobic pyrite at acidic pH. Larger-scale experiments with both mineral pyrite and coal pyrite using Thiobacillus ferrooxidans and Saccharomyces cerevisiae as depressants, showed that these microorganisms are very effective depressants for mineral pyrite at acid pH, but they are largely ineffective at neutral and alkaline pH, where the mineral pyrite surface is not naturally hydrophobic. The flotation response of the coal pyrite was completely different from the mineral pyrite. The coal pyrite was most floatable near neutral pH, with the floatability decreasing in acidic or alkaline solutions. De¬pression of the coal pyrite by yeast was not selective between the pyrite and the associated coal under the experimental conditions.

Jan 1, 2000

By E. D. Gálvez, L. A. Cisternas, A. López-Valdivieso, F. Lucay

"The floatability of molybdenite fines in saline solutions was investigated through microflotation studies using a modified Hallimond tube. In addition, the effect of pH and gypsum precipitation from calcium ions (Ca2+) and sulfate ions (SO4 2-) ions in saline water on the recovery of the molybdenite was analyzed. It was found that the floatability of molybdenite fines significantly increased with the ionic strength of the saline solutions and is independent of pH above 0.5 mol/L ionic strength. The high floatability of molybdenite in saline solutions is explained as being due to the low electrostatic repulsion between bubbles and the edges of molybdenite particles, which is exceeded by interactions due to van der Waals and hydrophobic forces. The precipitation of Ca2+ and SO4 2- ions as gypsum had a detrimental effect on the natural floatability of molybdenite because of gypsum crystal attachment on the faces of the molybdenite particles. This precipitation phenomenon may be initiated in copper–molybdenite flotation circuits that use recycled saline water, like seawater containing Ca2+ and SO4 2- ions.IntroductionWater availability is a significant factor in mining projects. Water, particularly fresh water from rivers and underground water, is becoming a scarce resource for mining operations and new projects. Under these circumstances, the use of water with high concentration of salts in flotation plants is becoming increasingly important (Cisternas and Moreno, 2014). The use of seawater has been studied as a sustainable solution for many mining companies in dry areas located near the sea. Notably, using seawater in mining operations is how mining companies in Chile have coped with the problem of water resources (Cisternas and Gálvez, 2014). In 1930, small plants in Chile used seawater to float chalcopyrite from high-copper-grade ores. In 1975, the results of tests in pilot plants for the flotation of copper minerals with seawater were reported. It was found that froth formation in seawater at pH 9.5 was suitable to make the rougher circuit work properly, even without frothers. The Cenizas mining group successfully floated chalcocite, bornite and chalcopyrite in the Las Luces plant in Taltal in Chile using seawater (Moreno et al., 2011). Minera Centinela (Antofagasta Minerals S.A. Chile) is currently processing porphyry copper ores using a seawater mixture consisting of 20 percent fresh seawater and 80 percent recycled water. Lower consumption of flotation reagents was reported in both seawater and salt water. In addition, studies performed with synthetic seawater showed that certain frothers increase the froth volume, whereas others decrease it. Additionally, the froth produced with seawater carries a high amount of gangue, and low-quality concentrates are obtained, requiring more cleaning stages."

Jan 1, 2015

By P. Bevilacqua, G. Ferrara

Hydrocyclones and other dynamic separators are normally fed with pulps consisting of water and solid particles. The solids usually consist of particles of different sizes, shapes and densities. Except in the special case of monocharacteristic particles, the particles are segregated by these differences in size, shape and density. Segregation is magnified by the high values of centrifugal acceleration in the hydrocyclones. This paper develops a segregation theory that indicates the major variables involved. Experimental data on segregation under different operating conditions for mixtures of magnetite and/or ferrosilicon and nonmagnetic minerals are reported.

Jan 1, 1997

By Alvaro Souviron, W. W. Atkinson

The porphyry copper deposit at Los Pelambres is a resource exceeding 2 Gt (2.2 billion st) of 0.7% copper and 0.02% molybdenum. It includes a high-grade zone of +1% copper that is amenable to open-pit mining with a low stripping ratio. Metallurgical testing has indicated that the ore has exceptional characteristics, and that recoveries of 96% for copper and 93% for molybdenum can be obtained by conventional flotation methods. This paper summarizes the history of the prospect, the geology of the ore body and the surrounding area, and the procedures and results of exploration.

Jan 1, 1987

By Shouci Lu, Sun. Keji

Most phosphate ores in China are characterized by fine dissemination of the intergrown minerals and high content of carbonates. Therefore, in order to recover phosphorus minerals by flotation, some technological problems must be solved, such as fine particle flotation and separation of phosphate from carbonates. For effective flotation of finely ground phosphate ores and selective separation of phosphorus minerals from carbonates, S-series and L339 modifiers have been developed. A series of combined collectors with improved collector ability and selectivity have been developed and applied in several flotation plants in China. In this paper, CCLS, a combined collector for phosphates and PA-31 and a collector for reverse flotation of carbonates, are described. It has been found that some surfactants added with fatty acids function well in flotation at lower temperature, hence heating pulp in winter may be excluded. It is important for energy savings. The synergy mechanism of these additives in fatty acid flotation is discussed in this paper.

Jan 1, 1999

By Safdar A. Gill

The technique of installing small diameter caissons (drilled piers) through soft clays and water bearing ganular soil is well established for constructing building foundations. Over the past few years, the method has been utilized for constructing a large number of shafts extending into rock for the Chicago's Deep Tunnel Project. This paper will discuss design considerations for obtaining the most economic ground support system, the impact of construction procedures on the support and lateral pressures for design. Construction procedures will be described along with performance of the shafts.

Jan 1, 1981

On longwall coal faces in some Japanese coal mines more than half of the air coming from the intake gate road flows into the caved goaf and the air heated by the hot waste rocks in the goaf comes out through the latter half of the face. This still constitutes a major heat problem in spite of the introduction of gate and face air coolers. Therefore, in order to establish effective measures to improve the environ- mental conditions, it is essential to obtain information pertaining to the air flow pattern on the face as affected by the goaf conditions and the air flow regulating measures taken at the intake side of the face. Experiments for this purpose were carried out using a coal face model. The model was reduced to a scale of 1110th of the real face measuring 100 m long and 2.2 m high, equipped with self-advancing supports. The model design was also conceived to accomodate eventual modifications of the space of the caved goaf as imposed by the actual conditions.

Jan 1, 1980

By R. J. Sweigard, G. T. Lineberry, B. K. Slone, F. A. James III, D. S. Maggard

The depth at which it becomes more economical to use slope access instead of box-cut access for nearsurface coal reserves is termed the "transition depth." The transition depth can be established for a given coal property by considering cost estimates for those parameters that determine respective access methods. Fourteen parameters that influence access cost were identified, and ranges for these parameters were determined. A transitiondepth formula was developed to permit the determination of which is the better method of accessing a reserve, given information such as high wall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs and the cost of overburden removal and reclamation. In most cases in Appalachia, especially in eastern Kentucky, the observed transition depth ranges from 20 to 30 m (66 to l00 ft). This indicates that actual practice is consistent with the analytical approach used.

Jan 1, 2002

By L. W. Saperstein

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence-function-based computer program. Using an inverse application of the traditional influence-function technique, easily obtained surface displacements are used to analyze some of the complicated, expensive, and difficult-to- measure movements of the intermediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A secondary hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge-effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria, and in situ measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1988

By Erich U. Petersen, W. Dan Hausel, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

The geology of Wyoming has been compared to some of the richest precious metal producing regions of the world including South Africa, Western Australia, and the Superior Province of Canada. These areas are all underlain by ancient cratons that contain some of the oldest rocks on the surface of the earth. But unlike the other cratons, the Wyoming craton (also termed the Wyoming Province) has been greatly modified by Laramide tectonics which thrust slices of the ancient craton through younger Phanerozoic sedimentary rocks. Unfortunately, the nature of the Laramide tectonics left vast regions of the craton at the bottom of the Tertiary basins unavailable to direct examination, but the exposed slices in the mountain cores contain some of the best exposures of Precambrian rock in the world. The cores of these uplifts contain extensive regions of relatively unmineralized gneiss and granite that include scattered fragmented supracrustal belts formed of metamorphosed volcanic, plutonic, and sedimentary rock. Some of these supracrustal belts exhibit similarities to the gold- and nickel- rich terranes of Western Australia. Yet these areas remain incompletely explored. Archean (> 2.5 Ga) gold deposits within the Wyoming craton are primarily confined to greenstone belts and related terranes. These supracrustal belts include relatively narrow vein and shear zone deposits with strike lengths of tens of feet to more than a mile. Some exceptional deposits possess widths of greater than 15 feet to possibly as much as 300 feet, but the majority have widths of± 5 feet. These belts include Cu, Ag, W, Fe, and Cr mineralization, asbestos and pegmatites, and anomalous Ni and Sri in addition to gold. The Proterozoic terrane (<2.5 Ga) exposed in the cores of mountain ranges in southeastern Wyoming includes a thick miogeosynclinal metasedimentary succession which unconformably lies on the Archean craton. These metasedimentary rocks are separated from a predominantly metavolcanic terrane to the south by a major Precambrian suture, or shear zone. The metasedimentary rocks north of the shear include quartzite-hosted stratabound Cu-Ag-Au deposits, Au-Ag veins, and Witwatersrand-type metaconglomerates with isolated gold anomalies. The suture includes scattered base and precious metal deposits in shear zone cataclastics. South of the shear zone, the metavolcanic terrane includes scattered volcanogenic Zn-Cu-Ag massive sulfide deposits, at least one Cu-Au porphyry, and two large layered mafic complexes. The northern edge of one of these layered intrusives yielded some platinum and palladium to miners at the beginning of the 20th century. Phanerozoic sediments host many precious metal anomalies. Some Au-REE anomalies occur in Cambrian conglomerates. Ag-Cu-Zn stratabound deposits are found in bleached Jurassic redbeds in the Overthrust Belt of western Wyoming. The broad Wyoming basins include many enigmatic gold occurrences and anomalies that can only partially be explained by detrital transport in fluvial systems. Many of these anomalies were probably geochemically transported and precipitated. Rocks of Late Cretaceous age along the flanks of the uplifts have numerous black sand deposits. These paleobeach placers contain concentrations of detrital heavy minerals with anomalous titanium, rare earths, and in some cases gold. Gigantic base and precious metal deposits are associated with scattered composite intrusives in the Absaroka Mountains in northwestern Wyoming. This deeply incised volcanic plateau includes several Tertiary age copper porphyry deposits with significant Cu, Mo, Ti, Pb, Zn, Au, and Ag resources that rival the porphyry districts of the Basin and Range Province. In the Black Hills of northeastern Wyoming, disseminated Au-Th-REE mineralization is found in association with fenitized alkalic igneous rock. In addition to disseminated mineralization-scattered gold, fluorite, rare earth and copper veins; lead, zinc, and silver replacement lodes; and tin pegmatites are found in this region.

Jan 1, 1990