Search Documents

By Yoshihiro Kawarabata

INTRODUCTION The shield-driven method in Japan has been adopted widely in soft ground tunneling, namely, subway, water supply, sewer and utility tunnels, and recently this is an indispensable method in urban area. Since this method was started to adopt on a full scale from the beginning of 1960, construction achievements in length were about 830 km for 15 years until 1974 (1). According to the recent informations of the Japan Tunneling Association, the achievement in length under construction as of December, 1977, was about 350 km (2) and the extention of increase in shield-driven method can be guessed (Tab. 1). Tab. 1 - Achievement in Length by Shield-driven Method (As of December, 1977, Unit: m) (---): Achievement by Okumura Corporation [ ]

Jan 1, 1979

By J. A. Finch

The photographic measurement of bubble diameter is tedious and restricted to vessels with transparent walls and relatively low bubble concentrations. A new method for predicting bubble diameter in a flotation column has been developed and confirmed by comparison with measured mean bubble diameter (Yianatos et al., 1987) Flotation columns are not mechanically agitated. This note describes an extension of Ms method to a mechanically agitated flotation machine. A recent publication by Szatkowski (1987) provided sufficient data to calculate bubble diameter by the proposed method and compare with values determined photo- graphically. Method In a two-phase system (gas and liquid), bubble diameter (db), superficial gas rate (Vg) and liquid rate (Vl), and gas holdup (Eg) are linked by two relationships (see the nomenclature at the end of the paper for definitions of symbols). [ ] Equation 1 is the definition of slip velocity (relative gas to liquid velocity) for a countercurrent gas-liquid system, and equation 2 is an adaptation (Yianatos et al., 1987) of the expression of Masliyah (1979) for hindered settling in a multispecies system. The solution for bubble diameter is by repetitive substitution of estimates of db in equation 2 until the calculated Ubs is equal to the measured Ubs in equation 1. Results and discussion Table 1 presents the data obtained by Szatkowski (1987) from a mechanically agitated laboratory flotation machine. The machine generated bubbles by directing a gas stream into the vicinity of a disk rotating at Ngh speed (up to 8000 rpm) in the flotation slurry. The air was completely dispersed in a swarm of fine bubbles. A photographic technique was used to determine the distribution of bubble size. The mean diameter and standard deviation were then calculated. Table 1 provides all the information necessary for computing bubble diameter (Vl is assumed zero). The calculated bubble diameter is presented in Table 1 as d;. Figure 1 plots measured versus calculated bubble diameter and shows reasonable agreement between values. There is an apparent tendency to undercalculate the small bubbles and overcalculate the large ones.

Jan 1, 1987

By R. V. Huff

An in-situ leaching technology was developed for copper oxide minerals at the Van Dyke deposit at Miami, Arizona. This paper discusses the process developed and the activities that occurred. Specifically, the activities of well installation, deposit data acquisition, leach testing and equipment development are reviewed. Installation and operation of the test facility are described.

Jan 1, 1988

By Pascale St-Germain, Michael Li, Lionel J. J. Catalan

The oxygen flux into water-covered reactive sulphidic tailings is required for evaluating the long-term performance and predicting the quality of engineered shallow water covers. This information can also serve as an input to the design of water covers for reactive tailings decommissioning. This paper describes some dissolved oxygen (DO) profiles recently measured in the field across the tailings/water interface and oxygen fluxes derived from these profiles. These fluxes are compared with previously reported flux values from similar field measurements. Techniques and pitfalls for measuring DO profiles and calculating oxygen fluxes are also discussed.

Jan 1, 2000

The transfer of Langmuir-Blodgett (LB) monolayers of collector molecules to the surface of mineral crystals is an excellent method for the study of collector adsorption phenomena and is of particular significance in the understanding and development of improved flotation separations. The fatty acid/fluorite and amine/sylvite potation systems were investigated by the Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) examination of transferred LB monolayers of collector molecules at the surfaces of the mineral crystals. The [ir]-A isotherm study of fatty acid and amine, typical anionic and cationic collectors, showed the different packing trends dependent upon the pH and/or type of subphase. This result clearly reflects the effect of pH on compound formation and dissociation of the collector molecules. Identification of the collector adsorption state and confirmation of the validity of the FT-IR/IRS adsorption density equation were included in this research effort. This allowed for a detailed discussion of collector adsorption phenomena. As a result of these experiments, it is possible to relate the hydrophobic character of a surface to the nature of the adsorbed collector structure and thus describe flotation behavior in greater detail. For example, it appears that in the case of oleate/ fluorite the equivalent of an LB monolayer can form spontaneously during adsorption from solution, and this structure is known as a self-assembled monolayer (SAM). Such a state is significantly more hydrophobic than the oleate structure which forms on the calcite surface at an equivalent adsorption density.

Jan 1, 1996

By S. Lee, F. Campero

"Past heap leach design has evaluated hydrodynamic parameters based on a uniform particle size of heap material, but has ignored the equal importance of the instability of fine migration within heap stack in the beginning stages of the irrigation process. The proposed probabilistic model evaluates internal fine erosion and segregation potential of well-graded crushed ores by considering the entire particle size distribution shape and site compaction degree. Using this model, unsaturated flow model parameters were successfully evaluated based on synthesized soil-water characteristic curve (SWCC). Additionally, one-dimensional unsaturated transient flow modeling with Hydrus 1D® showed that the different recovery efficiencies of heap material under unsaturated flow patterns depending on the particle size distribution and compaction degree of heap material. Agglomeration preprocess employed by most heap leach sites can reduce the potential of fine erosion within heap material significantly, but internal stability of crushed ores and hydrodynamic-based analysis of heap material’s pore structure is equally important in the prescreening stage in order to improve efficiency of the heap leach and avoid a costly agglomeration process. INTRODUCTION Accurate estimation of heap leach recovery is a difficult task due to the variety of design parameters that need to be considered - such as geochemistry, hydro-dynamics, and geotechnical design aspects, most notably particle size distribution through the process of agglomeration. After agglomeration techniques were introduced to heap leach design, the influence of particle size distribution and compaction degree in enhanced heap leach recovery has been neglected. The main purpose of agglomeration is to prevent fine segregation and internal erosion during and after heap stacking for well graded crushed ores, which will eventually diminish heap reach recovery. Recent studies show that agglomerated heap materials that had been consolidated at 10 meters below heap surface can release the fines after contact time with lixiviant to the compacted heap material and produce poor drainage performance (Milczarek et al, 2013). It must be noted that engineers and practitioners should investigate feasibility of agglomeration benefit prior to heap leach design because the agglomeration process can incur up to 20 or 30% of project costs. Internal stability of stacked heap material is mainly governed by the particle size distribution of crushed ores. Depending on this stability, segregation and internal erosion of fines can be mitigated by the application of moderate compaction effort during heap construction. Investigation of segregation and internal erosion potential therefore takes precedence for well graded crushed ore since reaction time and contact area with lixivant are greater in finer ores."

Jan 1, 2016

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

The Coal Utilization review arrived too late to appear in the May issue. Coal utilization technology is improving due to the urgency with the 1990 Clean Air Act and the incentives provided by the Clean Coal Technology (CCT) program. Advances in the CCT are the subject of this report because of their broad industry application, support and involvement. Clean coal demonstration program Projects in the $5 billion Clean Coal Technology program are jointly funded cooperative agreements - not contracts - between government and industry. The industry participant in each project contributes at least 50% of the total cost. The participant takes primary responsibility for the project and is awarded any patent rights for inventions that may occur during the demonstration. The government, on the other hand, ensures that schedules are met, costs are controlled and project objectives are met.

Jan 1, 1991

By J. H. LaVerne Palmer, W. (Bill) C. Cox, Lorant B. Geller

An erector transporter (ET) has been designed and built to lift, carry and erect heavy machinery components, in particular the components of a 7.6 m diameter tunnel boring machine (TBM), within the access tunnels of a submarine coal mine in Eastern Canada. The ET is capable of manoeuvring within a 7.6 m tunnel while precisely positioning components as large as 6 m in diameter and weighing up to 27 tonnes each. The unit can negotiate 20% grades while carrying loads of 30 tonnes. The major design features, verification tests and performance trial results are presented. The versatility of the ET is such that many other applications are possible.

Jan 1, 1985

By Jack G. Pippenger

This report focuses on the procedures required to review, prepare specifications, bid, and purchase a fully integrated computer system for utilization by engineering personnel in all phases of mine engineering. The presentation is based on the experiences encountered in 1984 in procuring an engineering computer system at The North American Coal Corporation's Western Divi- sion. A two-phase report detailing the purchasing process and subsequent utilization of the engineering computer system will be given. Special detail is also provided on the final system hardware and software setup.

Jan 1, 1989

By Deepak Malhotra

Following a severe recession in the early 1980's, mining companies have taken significant steps to improve metallurgy and reduce operating costs. They do not view chemical reagents and the long-term relationship with reagent producers the same way they did two decades ago. This paper discusses the general perspective of changes that have taken place over the years, especially with respect to cost of production, selling price and environmental constraints. A cooperative program between the consumers and producers of chemical reagents is recommended to understand each other's problems and identify the present and future needs of the mining industry. This approach will be beneficial to the long-term survival of both parties.

Jan 1, 1994

By F. Breu, R. Fraser, R. Lawrie

Diesel-powered underground mining equipment is generally accepted as the most productive, safest, and most efficient equipment used in underground mining operations. Widespread application of this equipment to underground mining is restricted, however, largely because of the difficulty of controlling the diesel engine exhaust emissions. This paper briefly examines control devices currently available for underground application, and also discusses the theory and mechanics of controlling diesel emissions with particulate traps and filters.

Jan 1, 1988

By G. J. Lindenburg, T. L. Wilson

The Velvet uranium mine is located in the Big Indian district of the Colorado Plateau. The uranium ore body lies within the lower Triassic Chinle Formation, and the ore is associated with west-south-westerly trending fluvial sand systems. Exploration and mining are directed by longhole drilling and radiometric sampling. Results of the gamma probing, face scanning, and geologic mapping guide mining decisions and planning. Three people are directly involved with the geologic procedures: two geologists and a mine supervisor. The two geologists map, do rib scans, and direct longhole drilling. The third man involved, the mine supervisor, has last minute directive action based on shot hole probe data.

Jan 1, 1992

By J de Cuyper, S. R. Rao, J. Leja, K. S. Moon, W. Freyberger

A prolonged grinding of sulphide ores in steel mills appears harmful to flotation recovery and selectivity whenever xanthates are used as collectors. Particles finer than about 10um show a pronounced decrease in floatability. A supposition was made that the cause of the reduction in floatability of ground sulphides is the presence of metallic iron abraded during grinding and deposited on the ground particles. Electro- chemical measurements were made of mixed potentials developed by different sulphide-mineral electrodes (galena, chalcopyrite, pyrite, marmatite, pyrrhotite) in xanthate solutions, without a direct con- tact or in contact with a metallic iron electrode. These measurements showed that without a galvanic contact between the sulphide and the iron, the values of mixed potentials were in the vicinity of the xanthate/dixanthogen redax potential. When contact with iron was established, the mixed potentials shifted towards the more negative reducing or cathodic values, The shift was greater the higher was the ratio of the surface areas: iron electrode to sulphide electrode. Further, the shift in mixed potentials was greater the more reducing were the conditions on the sulphide electrode. Chemical analysis of reaction products produced on the surfaces of sulphides and in the bulk solution showed that less thiosulphate was formed in all of the sulphide-xanthate systems and that more elemental sulphur was detect-

Jan 1, 1976

By M. E. Orman

Many factors must be considered when designing a heap leach pad. Geotechnical properties of the ore, can and will affect how well an ore leaches, the solution recovery, stability of the heap, and settlement. As a heap is stacked some of these properties will change due to the increased load. In order to properly design a heap these properties should be determined beforehand so that the heap performs as intended.

Jan 1, 1997

By J. M. Melluish

The metallurgical response of the Point Leamington deposit has been studied. Two series of bench tests were conducted and various ore samples and flotation products were examined using image analysis techniques. The majority of sphalerite and chalcopyrite grains in this texturally complex ore were found to be smaller than 10 micrometers. Copper recoveries were low with losses mainly as fine inclusions in pyrite. Sphalerite recoveries were somewhat better due to a generally coarser habit. Gold and silver recoveries were also low and only solid solution silver was identified in the ore. The deposit shows poor economic prospects unless additional tonnage of high grade zinc ore can be delineated.

Jan 1, 1989

By J. L. Fuller, N. A. Abdel-Khalek

This paper contains a brief summary of design descriptions and generally accepted designations for longwall ventilation systems. Various ventilation systems for longwalls developed using single-entry and multiple- entry systems are discussed. Design considerations specific to longwall mining are included.

Jan 1, 1991

By Shaoxian Song, Shouci Lu, Jingyon Gou, Pan Yiuwen

The calculated potential energies of interaction between hydrophobic particle of three minerals (rhodochrosite, quartz and talc) and air bubble show that the energy of hydrophobic interaction is the dominant factor for their attachment. An attachment rate equation, integrating particle -bubble collision and adhesion by introducing a "capture efficiency", has been put forward. It was found that the hydrophobic particle-bubble aggregates can not be disconnected in the bulk zone of flotation cell, whereas in the impeller zone the breakup may occur, particularly for the coarser particles captured by bubble. Finally, the flotation rate constant was estimated theoretically and verified by experiments.

Jan 1, 1995

By John W. Tieman

The increasing magnitude of our nation's pollution problems seems to stem from two main factors: urbanization and technical advance. In 1920, less than half the country's 106 million people lived in cities. Forty years later, the urban population accounted for 70 percent of the nation's 179 million. It is predicted that by the end of the century, 95 percent of the U. S. population, estimated at 280 million, will live in urban areas. As these people live increasingly in city concentrations, their residues also concentrate. With technological advances to support the increasing population, the variety and quantity of goods that we use also increases. New materials and processes result in increases in pollutants, some of them new. The harmfulness of these pollutants is sometimes known, but sometimes only suspected. One pollutant of concern at the present time is sulfur dioxide, the product of combustion of sulfur-containing fuels. Research on processes to remove sulfur oxides from flue gas has been in progress for many years. Pioneers in this field were the British who, in the early 1930's, installed a full-scale flue gas scrubbing unit on a 120 MW boiler using alkaline water from a Thames estuary plus chalk. Since that time, various methods have been studied by many investigators. Federal laws covering air pollution started with the 1955 Air Pollution Control Act. With the advent of the Air Quality Act of 1967, and subsequent publishing of criteria and available technology for control of sulfur oxides in January 1969, the clamor for information on commercially available control techniques to remove sulfur from fossil fuels has rapidly increased. Although many state-of-the-art papers have deluged the literature during the past several years, the research going on in the area of sulfur oxides control is of such importance that periodic reviews are justified. It is the purpose of this paper, therefore, to again review the state-of-the-art, but this time from the stand-point of what is immediately commercially available

Jan 1, 1972

By F. P. Jung

This presentation will be a general overview of the Cerrejon Coal Project being developed jointly by Carbocol, an entity of the Colombian government, and Intercor, an Exxon affiliate. The word "Cerrajon", by the way, is simply Spanish for a small hill. There is a distinctive hill near the mine site, and it's the only landmark of any significance. It's shown in Figure 1. So the locals call this area "El Cerrejon", "the little hill." Let me start with some of the highlights of the project, summarized in Figure 2, and then go into more detail later. A four-year feasibility study covered the geology, quality, engineering, construction operation and marketing of coal from this region. This study led Exxon to declare the project as commercial in July of 1980. Then in September of 1980 the president of Colombia gave the government's okay to proceed.

Jan 1, 1982