Search Documents

By Joseph Lynch, John DiPonio

This report refers to the Chicago Deep Tunnel Contract 13A, which was the first contract let in the City of Chicago requiring the construction of deep drop shafts for the transportation of high level sewage to the deep tunnel system. The basic contract required the contractor to construct certain drop shafts designed to deliver surface and high level sewage to the deep tunnel system approximately two hundred feet below. The design of the drop shafts was in a degree affected by their proximity to the existing deep tunnel. The tunnel, approximately three and one-half miles long, was to have five shafts dropping sewage at five locations. Four of the drops were approximately one-half mile apart and spaced from the dead end of the tunnel. One shaft divided the remaining two miles from the existing work shaft at the southeast end of the tunnel wherein a 220' deep pumping station was to be built. The existing tunnel had been built some time previously and all dewatering had stopped, allowing the tunnel and main shaft to fill with water. According to the plans, the drop shafts were all between fifty and ninety feet north or south of tunnel center line, and located in heavily built-up residential and industrial property. This then defines the problems: How do we control the water. If we excavate from the top down, how do we handle the slurry and the muck from five locations. How shall we construct the connecting tunnel between

Jan 1, 1997

By R. Edward Williams

The Spa1lation Process Because of the low thermal conductivity of many hard rocks, rapid heating of these rocks produces a thin surface layer in which the temperatures attain high values. Thermal expansion of this surface layer is constrained by the reminder of the still cool rock, and when stresses within the surface rock become high enough, the surface rock breaks away from the cooler rock behind it and flies or falls off as a thin flake called a spall. Then the next, newly exposed surface is heated, and the process continues. This process is the basis of spallation drilling. The hot gases from a jet burner provide the heat for spallation to occur, and their high velocity provides a scouring action that transfers heat to the rock and removes the spalls as rapidly as they form. Spallation is a process which works in very hard rock. It is dependent upon the thermal expansion coefficient and the thermal diffusivity of the rock but is also affected by any discontinuities in the rock. To date the efforts which have been made to evaluate the various rock according to their spallability has been minimal. As the success of this process is dependent upon the characteristics of rock it is expected that the study of rock mechanics will prove to be of greater value to this program than to the other mechanism for drilling and excavating rock. Commercial Uses of SPALLATION In the 19408s, the Linde Air Products Division of Union Carbide (UC 1 began developing spallation for use in mining taconite ore, which is presently the chief source of iron in the United States. In this work UC developed a jet-piercing tool that burned fuel oil with oxygen to produce spallation and contained mechanical cutters to remove rock that was not amenable to spallation. The UC jet-piercing machines have since produced about 40 million feet of shallow blast holes used for emplacing explosives in the taconite mines. During this work it was found that hole diameters could be increased by merely reducing the advance rate of the burners and that existing holes could be enlarged by making another pass through the hole with the same burner. The Browning Engineering Go. of Hanover, N.H., has developed a hand-held spallation burner to cut slots in granite. It has been used for a quarter of a century and is now standard equipment for quarrying granite throughout the world. This burner, which resembles a small jet engine oriented with its exhaust pointed downward, is the forerunner of a flame jet burner used to spall experimental holes in granite at maximum rates in excess of 100 ft/hr when operating in hard, competent granite. It uses No. 2 fuel oil, which is burned with compressed air. The system uses water to cool the burner and the exhaust gases. These gases, along with the steam produced from the cooling water, blow the spalls from the hole. Experimental Work Theoretical and experimental work has been accomplished by the Massachusetts Institute of Technology and the Los Alamos National Laboratory. This work is reported in Refs. (3) and (4). To verify the experimental results of this work laboratory scaled down field tests were conducted using two we1 1 characterized granites from quarries in Barre, VT and Westerby, RI, under defined heating conditions. In the laboratory tests a propane - oxygen heating torch was used to direct a flame at the granite surface and the spal 1 ing process was examined at various heating rates with a high-speed video taping system operated at 200 frame per second. This produced a time-lapse sequence where the onset of the spallation process was easily distinguished. Also the heat flux from the torch to a flat surface at various stand off distances and flows was measured. A similar set of tests was conducted using the more easily quantified and uniform heat source of a 1.5 kw GO2 laser. This allowed accurate

Jan 1, 1986

By Richard M. Crowell, Laurie M. Tahija, Keith D. Dagel

Echo Bay Mines Ltd. operates a gold heap leach in Round Mountain, Nevada, U.S.A. In the past two years, the mine has expanded operations from 13.5 kt/d (15 kst/d) to 41.0 kt/d (45 kst/d), making it the world's largest gold heap leach operation. The expansion is a separate system from the previous 12 year old plant, yet very similar. The flowsheet contains open circuit primary, secondary, and tertiary crushing with interstage screening. A leach pad stacker loads reusable asphalt leach pads. The process plant features carbon adsorption, pressure strip, electrowinning, and electrorefining.

Jan 1, 1990

By Neil Runciman, Greg Newson, Nick Vagenas

This paper discusses simulation modelling of underground mining operations at a typical mine in the Sudbury mining area in Ontario, Canada. The PC simulation software, WITNESS Version 7 Release 6.0 by AT&T ISTEL, is used to model the drilling, blasting, hauling and ground support operations. Simulation is used to investigate the development mining cycle and determine the capabilities and flexibility of WITNESS to accurately represent the mining system under consideration. The simulation study discussed in this paper provides a first step in determining the successful application of WITNESS in the underground operational aspects of the mining industry.

Jan 1, 1996

By Michael Rieber

Capable of establishing a net present value of zero over a short period of time small mines, though not simply scalers of large operations, minimize market risks and reduce investment capital. Particularly now they are relevant to LDC development. Small mine concepts are reviewed with emphasis on sizing, speed, and LDC problems. The special problem of gold and the precious metals is examined with respect to mine evaluation. Small mine analysis is introduced with emphasis on the financial model including gold price forecast considerations.

Jan 1, 1987

By Edward Burris, Terry Gorsuch, Joseph M. Hans

INTRODUCTION In any large earth-moving operation, good planning and management are necessary to complete the operational tasks promptly and successfully. When an earth moving operation is complicated by radioactive contaminants, normal earth moving techniques and procedures must be modified. Any planning and management, therefore, must include the radiological aspects of the operation. It was found that the radiological aspects dominated most of the planning and management activities and were extended to all facets of the decontamination work at the former Shiprock uranium millsite. These planning aspects are discussed and their use to develop a work plan is described. The management aspects are discussed and their use to establish a management structure are also presented. PLANNING Some method of procedure, formulated beforehand, was necessary to govern the decontamination work at the former Shiprock uranium millsite. This procedure was expressed in the form of a work plan which served several listed purposes. 1. It defined the work to be done and the sequence it would follow. 2. It was used as a yardstick to measure progress. 3. It was used to assign organizational responsibilities. Several factors were considered to aid in the development of the plan. These factors are discussed below: Goals It was established that radiation exposure was occurring to persons working at the millsite, and in an around the community of Shiprock, from airborne radioactive mill wastes and radon-222 exhaling from the tailings piles. The goal set for the decontamination work was to reduce on-site exposures to levels acceptable for the millsite occupants. The attainment of this goal would also have a substantial impact in reducing off-site exposures. The objectives necessary to achieve the goal were consolidation and containment of the wastes. The former objective implies decontamination of the millsite and environs, and the later implies stabilization of the wastes. In practice, a total and complete decontamination of the millsite and contaminated environs would be very difficult and costly. The costs for decontaminating them could be high enough that an alternative method might be more cost-effective for reducing human exposures (i.e, move the affected people away from the source). The interim guide "Radiological Criteria for the Decontamination of Inactive Uranium Millsites" was used for the decontamination criteria (EPA 74). Briefly, the criteria state that off-pile decontamination should be effective enough to reduce the net above ground exposure rate to less than 10 [u]R/hr for unrestricted use of the affected area. When decontamination cannot readily be achieved, the exposure rate levels could be relaxed to 40 [u]R/hr; however, the affected area has to be restricted. The second objective, waste containment, means isolating the wastes from the biosphere. Since no method of containment was available at the beginning of the millsite decontamination effort, temporary containment (interim stabilzation) became the objective. The tailings pile and decontamination wastes would be covered with clean fill. The interim stabilization should last from 5 to 10 years until the final disposition of the wastes will occur. The goal, therefore, would be achieved by decontaminating the off-pile areas to less than 10 uR/hr where practical. The decontamination wastes would be used to plate the surface of the tailings pile and would be covered with clean fill. Radiological Survey The radiologial survey is the key factor for planning a decontamination activity. The survey should delineate the spread and depth of the contaminants relative to the decontamination criteria. Surface wastes, in general, can be evaluated for spread and depth with reasonable radiation survey equipment. Subsurface wastes on the other hand can be missed entirely, as happened during the radiation survey at the Shiprock site, although numerous exploration holes were bored and dug. The survey results can be used to define areas that may not be amenable to decontamination because of complications or safety reasons. For example, no decontamination of the bluff base was to be attempted because of the possibility the bluff might collapse on the personnel and equipment. Contaminated bottoms of decant ponds on the flood plain were not removed because they would be slurried by ground water. Slurry removal was deemed inefficient because the contaminants would be scattered and no equipment was available for its transport. In summary, the radiological survey defines the boundaries of the decontamination work and provides

Jan 1, 1981

By R. J. Manser

A mathematical model of a shaking table is being developed, for inclusion in a package for the simulation of gravity concentration. The general form of the modules and how they fit into the package is briefly described. The separation on a shaking table is controlled by a number of operating variables and the importance of these variables in the model development is discussed. The influence of wash water, feed pulp density, deck slope, deck amplitude and mass feed rate are reported. The form of the model is described being based on the probability of a particle of defined size and density reporting to a specific discharge site. The mathematical relationships which relate size and density distributions to variations in the operating parameters are presented. The use of these functions in the prediction of the performance of a shaking table is outlined.

Jan 1, 1986

By S. S. Nadgauda, A. J. Hathaway

Typically, as long as the coal quality is within the specified range, electric utilities have used delivered cost of fuel per million Btu as the primary criteria for qualified coals when making coal-procurement decisions. Such an approach may not fully address the total cost of using different quality coals at a given plant. A practical and easy-to-build model is described for estimating plant-specific utilization costs for coals of different qualities. Examples are included to illustrate the modeling results for plants operated by two utilities. While the model has certain limitations, it does represent an improved method for evaluating coal bids, and, consequently, reducing generation costs.

Jan 1, 1990

By J. S. Anderson

Size reduction models of cone and impact crushers have been developed using Whiten's generic computational structure for the description of crushers. They incorporate a laboratory single particle breakage test and the t-family of curves to describe the breakage behaviour of the feed ore. A quantitative model of 7-foot cone crushers has been developed, based on surveys of Svedala (Kobe) and Nordberg machines. Survey data on a Canica vertical shaft impact machine have been used to validate the impact crusher model. Given the crusher operating conditions, such as tonnage, feed size, set and liner condition, or rotor speed and radius, plus breakage information on the feed, the models provide good predictions of product size distribution, and appear to be robust over a wide range of conditions. They are incorporated in commercially available computer simulation packages.

Jan 1, 1998

By G. Schriever, H. Thiel, E. J. Foell

A long-term, large-scale, disturbance-recolonization experiment with relevance to the environmental effects of deep seabed mining is described. The study is funded by the German government and was launched in the abyssal eastern tropical South Pacific Ocean in February-March, 1989. After obtaining pre-impact baseline environmental data, a 10.8 km2 (4.2 sq miles) circular area of seafloor was disturbed using a specially designed "plow-harrow" device. An initial post-impact sampling series was carried out immediately after disturbance followed by a second post-impact sampling series six months after the disturbance. Plans call for repeated visits to the site at two year intervals to monitor the anticipated slow recolonization process until the area is inhabited by a new, stabilized community.

Jan 1, 1993

By Henry R. Tiedemann, William H. Hansmire, Harvey W. Parker

Although the use of precast concrete segments for tunnel linings has been common for many years in Europe, acceptance of this type of lining has been slow in the United States. This paper explores the cost, design, and construction considerations of concrete segmental lining with a view to promoting its use in this country when favorable conditions exist. The different perspectives held by owners, designers, and contractors are discussed. In addition to cost, other considerations include previous design and construction experience, size, length and function of tunnel, watertightness, and liability. Cost comparisons are made to traditional ground support and lining. Under favorable conditions, the use of precast concrete segmental linings can be technically feasible and cost effective.

Jan 1, 1987

By A. Perelli Cippo, R. Granata, D. A. Bruce

During the last few years, significant advances continue to have been made in aspects of grouting technologies used for ground treatment in advance of tunnelling. In permeation grouting, fundamental researches have continued into improving the penetrability characteristics of cement-based grouts. The twin advantages of field regrinding normal grouts to reduce cement particle sizes, and incorporating special additives into stable grouts, are now being systematically exploited in major soft ground tunnelling projects in Europe. The methodologies of jet grouting continue to be developed with special attention being paid to qa/qc issues, reducing unit production costs, and improving predictive capabilities for subsequent settlements.

Jan 1, 1993

By Dennis S. Kostick

Introduction Soda ash is known chemically as sodium carbonate, an important inorganic chemical. It has been produced for several centuries by processing certain vegetation and minerals. The US soda ash industry has evolved from several small sodium carbonate mining operations in the West. Now, a nucleus of six companies produce about one-fourth of the world's annual soda ash output US producers currently dominate the world market. But certain international events are occurring that will reshape the domestic soda ash industry in the next decade. Historical perspective Soda ash is used mainly in the manufacture of glass, soap, dyes and pigments, textiles, and other chemical preparations. All of these are the first basic consumer products produced by developing societies. About 3500 BC, the Egyptians became the first society to use crude soda ash. The soda ash was used to make glass containers. It was most likely obtained from dried mineral incrustations around alkaline lakes. Soda deposits were virtually nonexistent in western Europe. So people resorted to burning seaweed to obtain the ashes. The ashes were then leached with hot water and the solute was recovered after evaporating the solution to dryness. The solute, a crude "soda ash" was impure. But, it could be used to make glass and soap. These two products and industries were important to the population and economic growth of the region. About 11.5 t (13 st) of seaweed ash was required to produce about 0.9 t (1 st) of soda ash. Along the coasts of England, France, and Spain, seaweeds with varying alkali contents became important items of commerce and sources of soda ash before the 18th century. The LeBlanc process used salt, sulfuric acid, coal, and limestone. It became the major method of production from about 1823 to 1885. In the early 1860s, Ernest and Alfred Solvay, two Belgian brothers, successfully commercialized an ammonia-soda process to synthesize soda ash. It used salt, coke, limestone, and ammonia. The Solvay process produced a better quality product than the LeBlanc method. In 1879, Oswald J. Heinrich presented to the Baltimore meeting of AIME, a paper entitled "The manufacture of soda by the ammonia process." The paper compared the two processes and foretold the demise of the LeBlanc technique. World production of soda ash in 1880 was 680 kt (750,000 st). Of that, 544 kt (600,000 st) was produced by the LeBlanc process. Of the 2.8 Mt (3.1 million st) of soda ash produced worldwide in 1913, only about 50 kt (55,000 st) was by the LeBlanc method. The LeBlanc process was never used successfully in the US, except for a brief period from July 1884 to January 1885 in Laramie, WY. Previously, soda ash had been produced by burning certain plants, as exemplified by the early Jamestown colonists, or by recovering small quantities of natural sodium carbonate found in alkaline lakes, such as those found near Fallon, NV, and Independence Rock, WY. Before the 1884 startup of the first synthetic soda ash plant in the US at Syracuse, NY, most of the domestic soda ash demand in the East was met by imports, primarily from England. Large-scale commercial production of natural soda ash began in California in 1887 from surface crystalline material at Owens Lake. Production from sodium carbonate-bearing brines at Searles Lake began in 1927 (Fig. 1). In 1938, during exploration for oil and gas in southwestern Wyoming, a massive buried trona deposit, presumably the world's largest, was accidentally discovered. Recent mineral resource evaluation by the US Geological Survey and the US Bureau of Mines indicates that the Wyoming trona deposit contains 86 Gt (93 billion st) of identified trona resource in beds 1.2 m (4 ft) thick or greater. Additionally, there is about 61 Gt (67 billion st) of reserve base trona. Of this 36 Gt (40 billion st) is in halite-free trona beds and 24 Gt (27 billion st) is in mixed trona and halite beds. In 1953, the Food Machinery and Chemical Corp. (later shortened to FMC Corp.) became the first company to mine trona in Wyoming. Soda ash demand increased.

Jan 10, 1985

By Thomas F. Pedersen, J. Jay McNee, Alan J. Martin

Field sampling was conducted in Lake Junin, Peru in order to assess the post-depositional reactivity of the highly contaminated lake sediments. High resolution profiles of dissolved Fe, Mn, SO42- and H2S across the sediment-water interface illustrate that the organic-rich sediments in the main basin become anoxic within several millimetres of the sediment-water interface. These permanently submerged deposits in the main basin serve as a diffusive sink for dissolved Zn and Cu. Conversely, the periodically unsaturated deposits in shallow areas are characterized by the remobilization of Zn and Cu in the deep acidic (pH < 4) pore waters, resulting in the release of these metals to the overlying water column.

Jan 1, 2000

By Barbara C. Williams

U.S. Bureau of Mines researchers conducted field studies at an abandoned copper-gold mine tailings impoundment. Pore water quality was analyzed in the vadose and saturated zones. Three statistical procedures were employed to summarize the variability within and between the two zones. The results indicated that linear combinations of those variables reflecting sulfide oxidation and aluminum-silicate weathering best summarized the variability in each zone, and that the zones were most different on the basis of sulfide oxidation variables. The geochemical computer code WATEQ4F was used to assess the solubility status (saturation index) of minerals. Saturation indices of sulfide oxidation and aluminum-silicate weathering minerals were different in the two zones. It was demonstrated that the statistical analyses produced similar and complementary results to the geochemical code.

Jan 1, 1992

By Jindrich Fiala, Jirí Kout

The paper contains knowledge that have been achieved when the problem of airflow temperature and humidity changes prediction in mine airways was investigated. The substance of physical processes has been consistently applied. The methods of dry-bulb and wet-bulb temperatures calculations can be applied in any type of mine airway. The exceptionality of auxiliary ventilated airways is in the original solution of so called losing air flowing when a ventilation pipe is leaky. The combination of aerodynamics and thermodynamics solutions enable to determine climatic conditions on projected workplaces with a sufficient accuracy.

Jan 1, 1991

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine&apos;s strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

By Lowell T. Harmison

I appreciate very much the invitation to speak with you and the opportunity of bringing you messages from both the Secretary of the Department of Health and Human Services and the Assistant Secretary for Health/Acting Surgeon General of the U.S. Public Health Service. I would like to take this opportunity to congratulate you (the organizers of this Conference) on identifying the critical issues in the field and assembling such a broad array of experts to address them. I would like to present a brief view of the emerging framework for health that puts into perspective some of the aspirations of the Administration and to highlight several points with regard to prevention and occupational health. The goals are: 1. To improve the overall health status of our people. (This has been and will remain the National policy regarding health.); 2. To engage the Nation in the important effort of enhancing public health. (This is not reserved exclusively for the activity of the Federal Government or for State Governments. Public health has to be a cooperative effort that brings together all of the people engaged in the process of serving the people.); and 3. To pledge that health care will not be priced out of anyone&apos;s reach because of inflation. (It is clear that there are major tasks of bringing about economic recovery in our country. One aspect of this effort is to guard against the cost of health care not being allowed to rise beyond the reach of persons who need that care.) "How will these goals be achieved and what must change in the delivery of health and medical care in our society?" There are a number of real issues as well as perceptions that adversely affect the attainment of these goals: First, The cost of medical care is soaring and the public, industry unions and other elements of our society are becoming concerned. (They recognize the problem and are demanding a solution.); Second, There is a growing concern about the priorities that have been set. (For example, the evidence that preventive interventions are the most effective approach is overwhelming, yet medicine has not yet given that a high priority.); and Third, There is the perception that physicians do too much to too many people at too great a cost and that too much and too costly technologies are used. In view of the perceptions, we all must accept some changes and the challenges that needed changes will bring. A month before the new budget went to Congress, President Reagan went on nationwide television and told the American people that, "It is time to recognize that we have come to a turning point and we are threatened with an economic calamity of tremendous proportion and the [old business as usual treatment can&apos;t save us. Together we must chart a new course]." Now eight months down the road from this and a long Spring and Summer of discussion both within the Executive Branch and in the Congress, many plans and programs and concepts have emerged. The new course has been charted and the turning point has been made. Business as usual has been put aside and the Administration&apos;s leadership has been stretched and tested in putting forth a better approach with the reality that money is tight and that old habits of delivering care are difficult to change. The Congress has now given us a look at a new health budget that takes into account some of the harsh economic realities and that does make allowances for the persistence of familiar behavior. Against this background, it is now possible to begin addressing ways to provide health services to people at a price the Nation can afford to pay. There are without question difficult decisions involved but the Administration is committed to supporting and improving health care in America. It has been the President&apos;s contention that one of the principal causes of the inflationary spiral in the country was the steady and indefensible growth of the Federal budget. The problem stems from the fact that we have been living well, but beyond our means for nearly 30 years. Now we are discovering that there is a bottom to the barrel after all. It is possible for our society to run out of things like energy (oil), water or money. The health bills must be paid -- by Government, by insurance, by parents or by someone. Each year with a bigger shopping list and more money to spend the Federal Government went into the marketplace to buy. This action altered the

Jan 1, 1981

By Nancy J. Wheatley

I. INTRODUCTION The Massachusetts Water Resources Authority (MWRA) is a regional water and sewerage authority which provides wholesale water and sewer services to the Metropolitan Boston area. The MWRA was created by the Massachusetts Legislature as an independent authority in 1985 following the filing of a lawsuit in federal court to correct the pollution of Boston Harbor resulting from inadequate and inadequately maintained sewerage facilities. Immediately upon its creation, the MWRA began to tackle treatment plant issues, including addressing the need for a secondary treatment plant, planning for ceasing ocean discharging of sludge, and making interim repairs to the existing, antiquated treatment plants. The MWRA&apos;s initial activities led to a court-ordered schedule for construction of a single new primary and secondary treatment facility, for development of sludge management plan focussed principally on reuse, and for completion of a short term program of repairs to existing facilities. Once a schedule for completing these activities had been negotiated, the U.S. Environmental Protection Agency (EPA), a plaintiff in the federal court case, asked that the MWRA take "responsibility" for controlling discharges from combined sewer overflows (CSOs) within its service area. Combined sewers (sewers in which both sanitary sewage and storm water runoff are carried in a single pipe) presently discharge over 10 billion gallons of untreated wastewater into Boston Harbor and its [ ]

Jan 1, 1991

By R. L. Grayson, M. P. Miano, S. Yuan

Matching the productivity gains of continuous mining machines with the increasing performance levels achieved by longwall units has required creative thinking to assure that development is completed in time for uninterrupted longwall production. By using management information systems to coordinate support operations, the most productive planning decisions can be made. This paper focuses on the role of computer technology tools in achieving improved productivity from both longwall and continuous miner sections. The primary emphasis is on the planning process and the methodology developed to guarantee the best allocation of management and manpower resources.

Jan 1, 1995