Search Documents

By Jianping Zuo, Chunlei Zhang, Yong Zhang, Shouyang Gao

To study the fracture evolution of overlying strata for ascending mining in a short-distance coal seam group, a two-dimensional physical simulation model was designed based on a specific geological condition. The fracture development zone was divided into the compaction zone and active zone by monitoring and analyzing the macro fracture evolution of the surrounding rock mass during the excavation of multiple coal seams. The secondary fracture development process of the overlying strata was demonstrated with a physical model. The quantity, length, and inclination of the fracture were calculated with MATLAB software, and the results were verified by geological radar. The total number of fractures between two coal seams increased with a “parabola” shape during the excavation of the lower coal seam, the crack angle was mainly vertical and horizontal, and the number of horizontal cracks first increased and subsequently decreased; the excavation of the upper coal seam caused the secondary fracture development process of the overlying strata, and the relief range and its extent increased. The mining-induced cracks from the lower and upper coal seams connected with each other, especially the permanent vertical fracture in the cutting room side and face side. Finally, the three-dimensional gas fissure was formed.

Nov 24, 2020

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By Y. Pan, V. V. S. Vytla, P. Tukkaraja, R. BHARGAVA, S. Jayaraman Sridharan

Panel caving is an underground bulk mining method that utilizes gravitational force for mining massive, steeply dipping, and deep-seated ore deposits at a lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. Since caving is a dynamic process, the design of an effective ventilation system is a challenging task, and therefore, estimation of airflow resistance offered by the broken rock inside the cave is critical. The complex and dynamic nature of caving also makes it difficult to predict the airflow resistance by using traditional approaches. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

May 17, 2022

By G. M. Wilemon

The U.S. Bureau of Mines has conducted investigations on extracting phosphate values from wastes generated during the mining and beneficiation of phosphate matrix. These wastes may contain up to one third of the phosphate originally present in untreated ore. Samples of wastes were air-dried and leached using 93 pct sulfuric acid in the presence of methanol. Evidence for the formation of a calcium sulfate hemihydrate coating that hinders complete dissolution of phosphate is presented. Solid-liquid separations were enhanced when flocculation was effected using poly(ethylene oxide) (PEO) in conjunction with hydroxypropyl cellulose (HPC) or hydroxyethyl cellulose (HEC. A conceptual flowsheet for a proposed process using an acid-alcohol leaching technique is presented.

Jan 1, 1990

By Caibin Wu, Bin Xie, Jiaqi Tong, Ningning Liao, Chong Zeng

Understanding the energy-size reduction relationship is vital to grinding process; therefore, this paper aims to show the energy-size reduction of magnetite-calcite binary mixture in a laboratory wet conical ball mill. Single magnetite, single calcite, and blended magnetite-calcite mixture at three weight ratios in four particle sizes were ground in a laboratory wet conical ball mill at four grinding time periods. The results showed that the particle size distribution of both fine particles and coarse particles of single and mixture ground product fitted well with the PSD computed by Rosin–Rammler-Benne function. The larger mass percentage of calcite is, the higher t10 of binary mixture ground product is. On the contrary, t10 in the mixture decreases as the percentage of magnetite in the mixture increases. The different breakage behaviors in blended samples are due to the hardness and particle size. The results of calculated ratio of energy absorption factor showed that the calcite consumed more energy in the breakage process of binary mixture than ground alone. The JK size-dependent breakage model based on the t10 method fits all the experiment data, be it generated from pure minerals, mixtures at different weight ratios, or each component separated from the mixture.

Jun 4, 2022

By D. Pearson

About 15,000 tonnes of zinc per year is present in the dusts and fumes produced in electric arc and BOS steelmaking, secondary copper refining and brass ingot making. Apart from the use of some copper-smelter fumes for zinc chemicals manufacture, zinc is not recovered and their disposal by landfill entails some risk of pollution by leach-out. The paper describes processes for recovering the zinc based on leaching and electrowinning. It was shown that the procedures normally employed for purifying zinc-electrolytes derived from primary sources are sometimes ineffective for secondary materials. Alternative process routes are proposed. Source materials were leached with acidic or alkaline reagents and solvent extraction was employed for electrolyte purification in addition to the usual techniques involving precipitation. Examples of integrated flow sheets for specific source materials are presented.

Jan 1, 1980

By Steve Kral

"Liebherr, as most anyone involved with the global mining industry knows, is one of the world’s largest makers of mining and construction heavy equipment. The familyowned company has been around since the 1940s and, according to Stefan Heissler, by the end of next year, will employ about 44,500 people worldwide. Heissler is a member of the board of directors of Liebherr International AG.It all started for the Switzerland-based company when Hans Liebherr first recognized a need for heavy equipment in the construction industry, Heissler said. His first product, introduced in 1949, was the TK10, a mobile crane that, at the time, was a groundbreaking innovation to the heavy construction industry. From there, the company began its growth into a world-leading heavy equipment manufacturer that always relied on innovation.In October, Liebherr gathered a group of mining and construction magazine editors in Leoben, Austria to take a look at the company’s latest addition to the global mining and construction markets. On the mining side, Liebherr provided a demonstration of its T-236 100-t (110-st) haul truck and the PR- 766 50-st (55-st) crawler tractor. The one-day demonstration took place at the Erzberg iron mine near Leoben, where both machines are being proven.The Erzberg Mine, operated by VA Ersberg, has been in operation for about 1,300 years and is said to be Europe’s largest surface mine. It employs about 230 people and mines about 12 Mt/a (13,200 million stpy) of ore, producing about 3 Mt/a (3.3 million stpy) of fine-grained iron ore.T-236 rigid-frame truckThe new T-236 rigid-frame dump truck, with a diesel electric drive system, is Liebherr’s entry into the 100-t (110-st) class and is the first in this class with a four-corner, oilimmersed braking system. The haul truck was first introduced during the 2016 MinExpo in Las Vegas, NV. The unit has since successfully completed its testing phase and is currently in its first field operation trials at the Erzberg iron mine in Austria."

Jan 12, 2017

By J. J. Gusek, J. T. Gormley, V. Scovazzo

Glenrock, WY is underlain by two abondoned coal mines. Subsidence events have been recorded over the years, with the frequency increasing in recent years. As part of Wyoming's Abondoned Wins Lands Program, investigations including mining history/methods/mappings, subsurface drilling and material site searches were performed. Portions of the mines less than eighty feet from the surface, were identified as probable for subsidence. Subsidence control by hydraulic backfill was selected. Design included search and injection boreholes, water supply from the mines and the slurry mixing, transport and injection system. Injection system performance and backfill success is king monitored during construction.

Jan 1, 1986

By Bruce D. Hebb, Shahin Shadlou

Fiber Reinforced Polymer (FRP) is an excellent material choice for a broad spectrum of corrosive fluids and, in many cases, offers the best value per dollar. FRP Flanges present the greatest design challenge of all standard piping components. The theory underlying the design of flanges is very complex. In addition, due to the nature of FRP material, proper fabrication of the flanges is as critical as the design. In this review, the challenges of making FRP flanges along with the design techniques and best practices of fabrication that will lead to a high-quality flange will be discussed.

Feb 1, 2024

By Daniel F. Meyer, William C. Paschen

INTRODUCTION The problems involved with moving millions of tons of rock are being addressed by nationally recognized tunnel contractors who have converged in Chicago over the past 5 years. This wealth of expertise has been needed to meet the risk and challenge of constructing the world's largest network of underground tunnels which in turn has required a dramatic advance in the art and science of tunneling. These pioneers, through innovation, adaptation, and hard work, have eliminated the one major concern of The Metropolitan Sanitary District of Greater Chicago - how to move 8 million tons of rock. The Metropolitan Sanitary District of Greater Chicago (MSDGC) serves 122 municipalities covering 866 square miles in Cook County, Illinois. Of these cities, towns, and villages, 53 have combined sewer systems. On an average of once every four days, these systems overflow about 4 million gallons of combined sewage and rainwater into the area's rivers and canals. The overflows occur at approximately 640 outfall locations of which 10% are owned by the MSDGC, with the remainder of the points belonging to various other municipal bodies. All those who own these "point" sources of pollution are in violation of Illinois State and Federal regulations. To enable its member municipalities to come into compliance with State and Federal law, the MSDGC is implementing its Tunnel And Reservoir Plan (TARP). TARP is a regional solution to the problem of combined sewer overflow in the metropolitan Chicago area. TARP will greatly reduce the pollution of area waterways by intercepting the combined sewage and rainwater carried in the existing sys-

Jan 1, 1981

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By Chunbao Sun, Qi Liu, Chao Wang

Entrainment is a process by which fine and ultrafine particles are transferred to the flotation froth from the top of the flotation pulp, and eventually discharge to the concentrate product, evenwhen they are not attached to gas bubbles. Therefore, entrainment can be considered as a two-step process, one at the upper layer of the pulp to the flotation froth, and the other from froth to the concentrate. Entrainment is inevitable for both hydrophobic and hydrophilic minerals and is one of the significant factors affecting concentrate grade. This paper provides a comprehensive review of the entrainment mechanisms and entrainment models, as well as a summary of the main factors affecting entrainment and the techniques thatmay be used to lower or eliminate entrainment. Based on the review, we point out that selective aggregation of fine and ultrafine gangue minerals using appropriate process aids (polymeric depressants, inorganic salts, etc.) to increase their particle sizes appears to be a convenient and economical method. Directions of further research along this line are discussed.

Aug 31, 2020

By John Marsden

Despite the recent pullback in metal and mineral prices, and the associated market adjustments, the mining industry is still facing a serious issue with the declining availability of graduate expertise. This is due to a combination of an aging workforce, retirements and retrenchments, coupled with a lack of suitably qualified graduates entering the workforce. The issue has certainly improved since 2004 when the industry picked up the rates of hiring graduate engineers and mining/mineral school enrollments picked up in response. This hiring effort has helped to cover the ?gap? years from about 1985-2000, when industry demand for graduates was particularly poor. However, the recent market pullback is likely to set back this progress, as recruitment and hiring wavers as a result of cost cutting measures and economic uncertainty. A key issue for the mining industry is how to ensure the survival and growth of relevant ?core? degree programs. Such programs include mining, metallurgical, mineral processing and geological engineering. The mining industry needs a healthy, high-level education program to ensure an adequate supply of appropriately qualified graduates for the mining industry. Two-thirds of the professionals entering the minerals industry who graduated within the past 40 years graduated prior to 1985. Since 1985, we have been living off the legacy of graduation classes from the mid-1970s and early 1980s. It is estimated that we have been producing graduates at approximately 40 to 50 percent of the sustaining rate since about 1985. Further growth in the domestic industry would increase graduate requirements significantly, and the export of U.S.-graduates to other parts of the world (as is currently occurring) also impacts the total graduate requirements.

By WILLIAM M. CROSS, ALBERT ROMKES, BERNARDO MORENO BAQUEIRO SANSAO, Jon J. Kellar

In this research study, the interaction of particles with substrates of different roughness magnitude was investigated. Particle surface treatment, relative humidity (RH), and surface roughness levels were controlled in order to achieve separation of different particles by applying removal forces. Three different approaches to reproducibly roughen surfaces were used. Initially, glass disks were laser engraved to create a reproducible, controlled roughness substrate. However, the laser engraving method produced surface features that were much greater in scale than the particles. These scale differences were such that the substrates produced were not of value to this research. The second option investigated to induce reproducible substrate roughness was to scratch the glass disk using sandpapers of known grain size. A third approach to establish reproducible roughness was to use fine stainless-steel wire mesh substrates. In tests with sanded glass disks, the interfacial energy of plasma-cleaned (hydrophilic) glass beads had a high variation at 40% RH, showing non-uniformity of area of contact between particles and substrates. As the RH increased, it was expected that the interfacial energy of hydrophilic particles would increase, but this behavior was not observed. In addition, comparing the interfacial energy results of hydrophilic particles with hydrophobic particles, a region with significant interfacial energy difference was not identified. In the case of the stainless-steel mesh substrate, the mesh asperities and particle dimensions were comparable. Thus, the smaller particles had more area of contact with the substrate than the larger particles. For the plasma-cleaned (hydrophilic) beads, the recovery values had an average of 92.5% recovery when the RH was between 46 and 85%. For the hydrophobic beads, the average recovery was 19.0% when the RH was between 46 and 75%. Thus, the hydrophobic characteristic of the particle influenced its lower interaction with the mesh substrate. The difference in recovery can be exploited to achieve separation of particles based upon adhesive forces.

Nov 30, 2021

By Nasser Madani, Yerbol Tussupbekov, Sergei Sabanov, Zarina Mukhamedyarova

A case study was conducted on a metal mine operating in Kazakhstan, in which problems were associated with use of a complicated and outdated ventilation system and its high expenses. The mine needs to reconsider its existing ventilation system and identify the risks associated with operational losses when using this ventilation system. The aim of this study was to develop an efficient risk analysis method capable of estimating operational risks and financial benefits of the existing mine ventilation system. The developed risk analysismethod considers ventilationmodelling, riskmodelling, and financialmodelling.Ventilation modelling comprises ventilation simulation and ventilation financial simulation. In risk modelling, the number of risk events occurring with the use of existing ventilation system and the operational losses during these events is estimated. Financial modelling considers operational losses and ventilation financial simulation benefits and uses a dynamic cash flow model to estimate how cost variability influences the cash flow. As a result, the improved ventilation system attains an additional NPVa ranging from 3.2 to 8.5 million US$ at the corresponding defined probability of 90%. The results of this study reveal that the developed risk analysis method can efficiently estimate the financial benefits of ventilation modelling and consider risk events and their total operational losses associated with use of the existing ventilation system. This approach provides a range of possible outcomes and helps with deciding whether the ventilation system is appropriate or whether it should be updated to better suit the project financial benefits.

Jun 3, 2020

By Irving D. Cohen

In order to overcome our reliance upon foreign energy sources for both crude supply and finished products, we must realize the goals proposed by Project Independence. In general this involves expanding production of existing and new oil, gas, and coal resources, utilizing and improving nuclear technology and the developing of new energy sources such as solar, geothermal, oil shale, tidal, wind and stimulation techniques. There is a continuing debate, both in the scientific community and the consuming public as to the potentiality of nuclear power generation being cost effective and environmentally and safety conscious. The development of new sources of energy does not occur overnight; it is rather a continuing effort in time and money to achieve the goal of providing energy to an ever increasing demand. The public has been accustomed to the availability of energy whenever and wherever it was needed. The era of "energy gluttony" has begun to fade into the realm of "energy awareness". Unfortunately, it required the action of another country to bring the picture that has been discussed many times in the past by energy suppliers into correct focus. Nevertheless, the public responded by conservation efforts to reduce energy wastefulness. Still, the demand for foreign importation of energy supplies is on the rise. What is our recourse? The largest known unexploited energy resource available in the United States is our coal resources. Moreover, the Department of the Interior has noted that 63 counties in Montana, Wyoming, and the Dakotas hold 60% of the nation's least expensive strip minable coal. This western coal is the most abundant and least costly Fossil Fuel in the United States. It is acknowledged that western coal is an important input in meeting the energy needs of our nation.

Jan 1, 1976

By H. H. Murray

Significant changes in ownership and production of industrial clays have occurred since 2000. Clays covered in this presentation are kaolins, ball clays, smectites, (bentonite), and palygorskite (attapulgite)-sepiolite. IMERYS discontinued production of paper coating kaolins at their Cornwall operations and have expanded their kaolin production in Brazil. J. M. Huber sold their kaolin operation in Georgia to KaMin whose headquarters are in Ft. Worth, Texas. BASF purchased Engelhard?s kaolin and attapulgite operations in Georgia. ActiveMinerals purchased Southeastern Kaolin in South Carolina, Wilkinson County Kaolin in Gordon, Georgia, and Zemex Attapulgite in Quincy, Florida. Chemical Lime purchased Spinks Ball Clay Company in Paris, Tennessee. Most of the ball clays used in Italy and Eastern Europe comes from expanded operations in the Ukraine. Bentonite operations have expanded production in Wyoming and Montana because of strong demand for drilling mud, foundries, cat litter, and iron ore pelletizing. The production and exports of palygorskite in China continues to increase. Nanoclays utilizing sodium montmorillonite, palygorskite, and halloysite are actively being developed.

Jan 1, 2009

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By S. Deming

Coal is China's main source of energy. In 1988, 76.1% of commercial energy consumption was supplied by coal. To provide a rational utilization of its coal resources, China has paid considerable attention to coal preparation over the last 10 years. In 1980, there were only 105 washeries treating about 100 million tonnes of coal, but by 1988 there were 151 washeries treating 171 million tonnes per year. This paper describes the development of China's coal preparation industry; its growth, the equipment, and the technology. Statistics and information on the current status of the industry are also be presented.

Jan 1, 1991

By R. R. Klimpel

This paper describes a series of mechanical flotation cell results run with various chemical reagent schemes designed to economically improve the flotation performance associated with selected industrially available coals. The emphasis is on the identification of practical flotation methods of processing coals containing unusually coarse and/or fine feed sizes, of increasing the recovery of oxidized and/or difficult to float coal, and of increasing the selectivity of coal over pyrite in high sulfur coals.

Jan 1, 1991