Search Documents

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA's general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By R. E. Scheffel

In February, 1976, Ranchers Exploration and Development Corporation obtained an option from Foote Minerals, Inc., to evaluate reprocessing of two uranium tailing piles. Foote received ownership of the Naturita and Durango tailing piles in 1967 through the purchase of Vanadium Corporation of America. The option was exercised in November, 1976, after initial testwork proved that a viable extraction technique existed. Preparation for production at Naturita began immediately with engineering and en¬vironmental permitting proceeding simultaneously. Production began in December, 1977, just 22 months after acquisition of the property and-was completed 17 months later.

Jan 1, 1981

By Koehler Stout

Stopewall or room closure can be a problem in nining operations. In some mines, wall closure causes ore passes and nanways to collapse when they are enclosed in nine fill. When this phe- nomena occurs, heavy ground and, or, rock bursts frequently happen. Often, ground problems become progressively worse as mining in the stope block progresses toward the upper level. The sill and pillars in the level above may experi ence heavy ground and bursts. Sometimes the conditions get so bad in the stope that it is unsafe to mine the ore, so the stope is abandoned and the ore is lost.

Jan 1, 1980

By E. M. Frizzell

It is unlikely that improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel cost/shortages, and increasing haul distances as in the past. Therefore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this Bureau of Mines contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic, and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data were gathered from extensive literature searches, European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configurations.

Jan 1, 1979

By J. Weinstein

New erosion, corrosion resistant metal, ceramic, and polymer composite technologies are being developed and marketed by Alanx Products L.P. for use in hydrocyclones, pumps, valves, and other applications in mining and minerals processing. This paper will present an overview of the ceramic/metal composite material system and properties developed, which include excellent erosion/ corrosion resistance. Wear data will be shown from a variety of laboratory tests in dry and wet conditions, in aqueous neutral and corrosive environments. Comparisons will be made with a variety of competitive materials currently used in the industries sited. Data will also be presented on field tests with pumps and hydrocyclones in hard rock mining and other abrasive/corrosive environments. Field data from North and South America, as well as Australian mining applications will be highlighted.

Jan 1, 1992

By H. A. DeMirjian

Oil production rate and ultimate primary recovery from a heavy or viscous oil reservoir is usually limited to a very small fraction of the original oil in place. Typically, normal production rate is in the range of up to 10 barrels per day and expected ultimate cumulative production is up to 10% of in place values. Heavy oil reserves are not all alike. The physical properties of the rock, the liquid hydrocarbons, and depths of the deposits are so different that each reservoir poses a unique enhanced oil recovery problem. In some reservoirs thermal recovery by internal heat generation or external heat injection has been successfully exploited. In other reservoirs, mining the oil bearing formation for oil recovery by surface processing has been practiced. This paper will present an overview of the heavy oil recovery state of the art and discuss the critical factors leading to the decision for selection of a conventional hydrocarbon recovery or mining and extraction processes.

Jan 1, 1978

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

By L. Alagha, J. L. Corchado-Albelo

To address the U.S. Department of Energy’s critical minerals strategies regarding rare earth elements (REE) in the U.S.A. This study evaluated apatite-rich mine tailing from the historic Pea Ridge Iron Mine (PR) for possible enrichment of REE by the froth flotation process. Comprehensive characterization studies were performed on the tailing samples to quantify the REE content, identify the REEbearing minerals and their liberation behavior. The aforementioned characterization studies were: x-ray fluorescence analysis (XRF), inductively coupled plasma mass spectrometry (ICP-MS), and TESCAN’s Integrated Mineral Analysis (TIMA). The ICP-MS analysis showed that the concentrations of heavy-REE and light-REE were 8000 ppm and 3000 ppm, respectively. TIMA showed that monazite was the major REE-bearing mineral. Additionally, it was shown that monazite and other REE-bearing minerals were strongly locked within larger apatite grains. Findings from the characterization studies suggested that REE could be enriched using phosphate minerals’ direct froth flotation process. Flotation feasibility tests were performed using selected organic and inorganic iron oxides’ depressants, including polyacrylamide (PAM), in-house synthesized hybrid polyacrylamide (HyPAM), chitosan, sodium silicates, and corn starch. Results showed that the depressant’s efficiency at pH 9 was in the following order: HyPAM > chitosan > PAM > sodium metasilicate > corn starch. Zeta potential studies on the selected depressants indicated that chitosan had the highest adsorption on magnetite’s surface at pH 7. Therefore, additional batch flotation experiments using chitosan as an iron oxides depressant were conducted as a function of chitosan dosage. Results indicated that the highest P2O5 recovery of 55% and grade of 28 wt.% were obtained at 150g/t of chitosan. However, the concentrate’s highest total REE enrichment of 1.07% was achieved at a 200 g/t dosage of chitosan. The low enrichment of REE highlighted the complex mineralogy of the PR tailings and the need to implement additional beneficiation strategies before and after the froth flotation process.

Mar 2, 2022

By J. Brune, P. J. Coleman, L. Martini

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners’ activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly understand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985. This report describes an alternative method of analyzing and presenting MSHA data for the purpose of identifying high-cost, high-severity injuries and illnesses. Researchers at the NIOSH Spokane Research Laboratory (SRL) developed programs to find the top five most frequent accident classes, natures of injury, types of accidents and other selected variables from the MSHA database. Studying these variables gives a cross-sectional snapshot of the most frequent groups of injuries within a commodity, regional group or time period, and allows researchers to quickly understand developing patterns for new research projects. The primary benefit of this approach is to

Jan 1, 2009

By R. J. Miller

Rock strata, natural and mining-induced stresses, and structural features can combine to create dangerous instabilities in or around longwall panels. Rock noises and properties variations associated with local stress systems can be used to characterize developing instabilities. Through a learning process at a particular mine, guidelines can be developed to allow the determination of relative risk and timing of a potentially disastrous instability. Once a dangerous instability has been identified, operational modifications can be employed to get through the instability, or active measures such as destressing can be used to mitigate the instability. This paper will discuss how an integrated monitoring system and associated data processing can be used to develop a hazard prediction capability for a longwall mine.

Jan 1, 1996

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2018

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2017

By W. C. Goldberg

This paper presents pit slope monitoring and back-analysis case studies con-ducted to evaluate and, if possible, stabilize slopes at the Berkeley Pit in Butte, MT. Two specific slopes were studied in detail. The first slope was determined to be near limiting equilibrium, as evidenced by its response to the initiation and cessation of mining, while the second failed on three occasions. Back-analysis of the failed slope verified the laboratory-derived geomechanical properties of the earth materials. Early detection of slope movement can show a need to take action, including modifying slope geometry, dewatering if the slope were wet, and/or investigating and implementing artificial supports. Monitoring slope displacements in open-pit mines can supply data for predicting collapses and preventing serious damage, injuries, and/or loss of life.

Jan 1, 1989

By Erika Moonin, Jim Nickerson, Marcus Jensen

"This paper will explain how the Contractor and Owner avoided a contractual dispute involving characterization, impacts, and final remedy for challenging ground conditions encountered during drill and blast excavation of the starter tunnel required for launch of the tunnel boring machine (TBM). During excavation more than 600 feet underground, the Contractor encountered a large complex fault zone subject to more than 14 bar of water pressure. Successive ground inflows from the fault complex over a six-month period presented significant technical and partnership challenges for the team and ultimately delayed the project by nearly one year. This paper will discuss how the Contractor, Owner, and their respective consultants worked together to address these challenges, make decisions, and ultimately move the project to successful completion. PROJECT BACKGROUND AND NEED Seven states of the western United States of America rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River basin, including the Rocky Mountains, the Wind River Mountains, and the Uinta Mountains. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. During the 1980s and 1990s, snowfall was relatively abundant and Colorado River flows were high on average. Beginning in the year 2000 and continuing to the present day, snowfall has been well below documented historical averages and Colorado River flows have diminished. In fact, a trend toward diminishing flows is evident during the period of the historical record. This variability in Colorado River flows and the trend to lower flows is represented in the following Figure 1."

Jan 1, 2016

By G. Plenge, M. Brittan

"Plant design parameters for gold extraction, leach residence time and cyanide consumption are generally determined from standard bench-scale bottle roll or agitation leach tests. The application of laboratory data to process design has essentially evolved from the testing of oxide or low cyanide-consuming ores. Such scale-up factors may not be appropriate for ores that deplete cyanide and oxygen since this interferes with gold extraction kinetics. High cyanide-consuming ores also exacerbate the differences between the conditions applicable to small batch tests and large continuous operations. Testing a reactive high-sulfide South American ore deposit necessitated the re-evaluation of conventional bench-scale cyanidation procedures. Pulp density can be a major factor affecting the results for plant design purposes and should be treated as a test work variable. As with high clay-bearing ore, where pulp viscosity can hinder mass transfer, minimizing the influence of test equipment on gold extraction kinetics may require low pulp densities. This introduces interpretative complexity since cyanide consumption changes as a function of pulp density. Activated carbon also consumes cyanide, so its effect has to be accounted for in the case of carbon-in-leach (CIL) or carbon-in-pulp (CIP) plant flowsheets. Since cyanide is an expensive reagent, often a major component of plant operating costs, it is important that the scale-up of cyanide consumption from laboratory to plant be representative. The traditional method of reporting cyanide consumption in bench-scale testing is questioned since it takes credit for residual free cyanide in leach tails. The projected plant consumption may be better estimated by using the total cyanide addition in a laboratory test. We propose a test work protocol that categorizes the cyanide consumption into its components but requires more extensive testing to generate design data. The ultimate validation of scale-up factors used by project engineers requires rigorous bench-scale versus commercial plant comparative data. Such data are not readily available.IntroductionMajor factors in the design of a gold processing plant are gold recovery, leach residence time and cyanide consumption. These parameters are important determinants of project revenue and costs and, thereby, potentially of project financial viability. Estimates of the associated design criteria for a commercial plant are normally generated from laboratory cyanidation, carbon-in-leach (CIL) or carbon-in-pulp (CIP) tests using standard procedures (Angove, 2005). The key question is whether the standard laboratory test work procedures developed historically for low reagent consuming ores are appropriate for ores that are highcyanide and oxygen consumers.The present paper examines test procedural factors that can influence the test work results and, therefore, their interpretation for design scale-up purposes. The study refers in particular to a high cyanide-consuming sulfide ore. The ore was being tested to develop scoping level engineering design criteria for a proposed project in South America."

Jan 1, 2015

By C. L. Emery

The geology and early history of the discovery of potash in Saskatchewan as described by Heber Cole (1) and R. V. Thompkins (2) has dealt with the distribution of the salt beds and their potash content. From the many bore holes through the Prairie Evaporites the outlines and contours of the series have been well established. The thickest section of the salt beds lies to the north of the "barren" area and forms a belt running easterly to a point west of Yorkton. The "barren" area is a region where the salt has been redissolved and the strata have slumped down, to fill the voids. This area is of interest from the standpoint of rock mechanics. The potash-rich beds extend both east and west of the region. mentioned and the top of the Prairie Evaporite is at a depth below 3200 feet from the surface near Saskatoon and dips southerly at an average rate of about five feet to ten feet per mile.

Jan 1, 1966

By T. Faulkner, S. A. Richards

"Classic engineering economics provides the mining engineer with a fundamental approach to choosing between capital spending alternatives. This approach has been heavily used over the years and is an accepted technique for most investment decisions. There is a shortcoming that I have run into over the 15 year period when I worked in business planning roles. The classic time value of money approaches such as Net Present Value, Return on Investment, and Internal Rate of Return provide good estimates, but the input assumptions may fall short of describing the real material differences required by these analysis techniques. If the cost benefit analysis is defined solely on the improvement of the item being replaced or improved, the true profitability of the decision may be overestimated. Productivity improvement based capital projects can yield more accurate forecasts when conducted in concert with a “bottleneck analysis”. INTRODUCTION A review of the Theory of Constraints, (Goldratt, Cox, 1984) Lean, (Womack, 2003) (Rattner, 2006) and Six Sigma (Cryger, DeFeo 2015) lead us to recognize that these process improvement methodologies are oriented to the manufacturing process. These systems generally involve a factory that the material moves through on the way to becoming a final product. The mining challenge has many similarities to manufacturing once the ore has been won and made ready for processing. Before that point, however, the process is somewhat inverted while the ore is being won. Instead of the material moving through the factory, the factory is moving through the material. The Theory of Constraints (TOC) was used in an underground context by Baafi, Cai and Porter at 2015 APCOM, but even this groups’ analysis did not carry the concept from mining to shipping of the final product. There can be spatially distributed data that can affect the mining throughput constraints, some of which can be determined from exploration results. Identifying constraints can lead us to mapping productivity bottlenecks on future mining. Knowing this may improve decision making by eliminating one of Jim Fishbein’s three deadly sins of strategic planning: incomplete planning. When evaluating capital investment alternatives you should evaluate the impact of any proposed improvements on the entire operation. At the core of any mining system is the materials handling system. This can be typically expressed as the system that handles the raw material from the “face” through processing and then handling the finished product as well as the waste material. A “Bottleneck Analysis” is an investigation into the factors limiting a material handling system’s productivity (Goldratt, Cox, 1984). Mining material handling systems are usually composed of several linked components such as draglines, shovels, loaders, hydraulic excavators, continuous miners, longwalls, highwall miners, bucket wheel excavators, LHDs, feeders, conveyor belts, stockpiles, crushers, processing plants with various circuits, and waste handling systems. Each of the aforementioned components has a slightly different throughput capacity. When these are linked in series, the one with the lowest throughput capacity limits all of the others, creating the bottleneck for the system. Every material handling system has a bottleneck. In the mining environment, a subtle, but very significant phenomenon may also occur. The bottleneck may change as a result of a change in the raw feed qualities, face recession, overburden depth, digability, learning curve, and many others factors which may be derived from the drillhole data. These parameters often change as a function of the location in the reserve base, and may also vary with time."

Jan 1, 2016

By Stanley J. LeFond

The Republic of Botswana, one of the newer countries of southern Africa, attained independence on September 30, 1966. It covers an area of about 225,000 square miles (582,000 square kilometers) which makes it slightly larger than France, or slightly smaller than Texas. It is bounded by Zimbabwe, the Republic of South Africa and Namibia, including the Caprivi Strip. Angola and Zambia are close neighbors. (Map 1). Botswana lies at the center of the southern African plateau at a mean elevation of 3,300 feet (1,000 m). It is a natural habitat for most species of African fauna. The rolling sands and extensive grasslands of the Kalahari Desert cover the southwest. The climate is sub- tropical. Summers, although tempered by north- easterly breezes, are hot, but mean maximum temperature seldom rises above 100°F (38°C). Winters are dry with wide temperature variations, which often give rise to frosts.

Jan 1, 1981

By Dermot M. Ross-Brown

The objectives of this generic study were to use numerical modeling techniques to determine under what conditions seismic waves generated by an earthquake might cause instability to an underground opening, or cause fracturing and joint movement that would lead to an increase in the permeability of the rock mass. In general, the study showed that moderate earthquakes (up to 0.41 g) did not cause instability of the tunnel or major fracturing of the rock mass. An artificial rock-burst tremor with high accelerations, however, was found to be amplified around the tunnel, and fracturing occurred as a result of the seismic loading in salt and granite. In shale, even moderate seismic loading resulted in tunnel collapse.

Jan 1, 1981

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the U.S. National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs) and manufacturers of filtration and pressurization systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3-89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent with the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality to equipment operators inside of enclosed cabs of mobile mining equipment, thus minimizing respirable dust exposure.

Jan 1, 2014