Search Documents

By Michael J. Friedel

As part of a study aimed at understanding the hydrology of in situ leach mining (ISLM), the Bureau of Mines, in cooperation with the Cyprus Casa Grande Corporation and the University of Arizona, is investigating dynamic transmissivity conditions during ISLM of a copper oxide ore deposit. Spatial and temporal variations in ore zone transmissivity during two years of ISLM operations at the Cyprus Casa Grande mine are evaluated during sixteen intervals of steady-state injection and recovery well operation. Direct inversion of an analytical hydrologic model is used to obtain estimates of transmissivity at 58 well locations during these intervals. Univariate statistical and geostatistical methods are used to describe the temporal and/or spatial relationships that exist between transmissivity and other ISLM parameters, including average well injection pressure, average sulfuric acid concentration in leach solution, and the relative configuration of injection and recovery wells. Average transmissivity during the sixteen steady-state time intervals varies between 6.00 x 10-6 m2/min. (6.46 x 10-5 ft2/min.) and 3.61 x 10-8 m2/ min. (3.89 x 10-7 ft2/min.). A trend toward decreas¬ing transmissivity is evident during two year of ISLM operations. This decreasing trend is found to correlate with a decreasing sulfuric acid concentration in injected leach solution, and suggests increasing geochemical precipitation within the deposit. Geostatistical analyses reveal a dynamic and anisotropic transmissivity structure within the target ore zone, that is dependent upon spatial and temporal changes in injection pressure and well configuration.

Jan 1, 1992

By Elisabeth Tønnesen, Lloyd Tunbridge

"SUMMARY Injection grouting in rock around tunnels is used to reduce or stop water inflow. Little is known about the distribution of pressure within the rock mass during and after grouting. Instrumentation was developed to record pressure at the back of the packers inside the rock mass during injection grouting in order to improve our understanding of the process. Using this equipment measurements inside multiple injection holes during injection pumping have been made during several rounds of injection grouting in a tunnel. The data has been compared to the data recorded on the grout pumping rig and analysed to gain an understanding of the behaviour of grout injection process in the rock mass. The initial results are reported in this paper. INTRODUCTION Construction of a tunnel in soil or rock below the ground water table frequently results in the flow of ground water into the tunnel if the ground is permeable or fractures conductive. The injection of cement or chemical based grouts is frequently used during tunnel construction to reduce flow of water into a tunnel. Significant water flow into a tunnel is undesirable for several reasons: • there is a high cost in pumping out water over the lifetime of a tunnel; • drips and flows of water have to be diverted from the roadway or track; • where freezing conditions occur there is the possibility of ice build up and; • ground water levels may be changed possibly affecting surface water such as causing drainage of lakes and ponds, and changes in vegetation. Grout injection is most effectively done ahead of excavation to ensure that the grout penetrates the ground. Where heavy flows of water already occur into a tunnel the grout may be washed out before it sets. Normal practice in ground where water flows are encountered is to inject grout in a number of long holes ahead of the face with outer holes forming a ring around the proposed tunnel excavation – eventually forming a shield of grouted rock around the final tunnel, Figure 1. The holes may be sealed off a couple of metres into the rock with an expandable rubber plug around a pipe through which the grout can be injected, Figure 2. A one-way valve in the plug stops the grout from flowing back out of the hole when pumping stops and avoids grout flowing out through neighbouring holes. The rubber packer with a one-way valve permanently installed in the injection hole precludes the measurement of pressure down the hole when pumping is stopped."

Jan 1, 2016

By Abb Raymond

Finely processed industrial minerals in "powdered" form have long been utilized by the plastics, paint, rubber, paper, ceramics, and adhesives industries as fillers, extenders, coatings and special additives. These minerals, primarily calcium carbonate, talc, kaolin, titanium dioxide, and the like, have provided economic, uniform and consistent base materials which have, in turn, been used by the referenced industries to manufacture quality products. The focus of this paper will be the development of equipment and systems at ABB Raymond for the dry processing of such non-metallic minerals in order to meet what have become increasingly stringent requirements of the producers of these minerals. Changes in these requirements seem to have been accelerating rapidly during the last ten years, and it is expected this process will continue into the 1990's.

Jan 1, 1990

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Jurij Karlovšek, Wolfgang Angerer, Vojtech Ernst Gall, Jacob Grasmick

The International Tunneling Association (ITA) Working Group (WG) 22 “Information Modelling in Tunneling” has developed a guideline for the implementation of Building Information Modeling (BIM) concepts for Bored Tunneling Projects. The guideline primarily covers the use of BIM during the conceptual and delivery phases of a project. It provides Owners with an introduction to BIM, an overview of the current capabilities of BIM, and a guide for implementation for a Bored Tunnel. The document will be officially published at the World Tunnel Congress (WTC) in Copenhagen in 2022. This paper describes the need for the guideline and provides a preview of its contents.

Dec 1, 2022

By Theodore Triplett

To assess the value of various subsidence mitigation techniques, twelve linear foundations were constructed above a longwall mine. The structures were monitored during and after undermining, and footing curvatures at the time of cracking were compared with predicted values. An unreinforced concrete footing sustained substantial damage. Other footings received varying degrees of damage, with inclusion of a sand layer significantly affecting performance. A post-tensioned concrete foundation suffered minimal cracking. Also, a technique developed by the Bureau of Mines is presented for determining the subsidence, slope, curvature and strain of the ground surface.

Jan 1, 1986

By J. R. Carr

A crucial concern when implementing computer algorithms for geostatistical analyses on microcomputers is speed of execution. Kriging, in particular, typically relies on a Gauss elimination algorithm to solve for weights. Because such an algorithm is required for each estimate, the solution for weights can result in very slow program execution speed on a microcomputer. One approach to enhancing the efficiency of Gauss elimination is demonstrated herein. The upper triangle plus diagonal of the intersample covariance matrix is used in a modified banded Gauss elimination algorithm. Results show that such an algorithm yields approximately a two-fold reduction in execution time for kriging when the number of nearest neighbors used for estimation is large.

Jan 1, 1990

By F. F. Aplan, T. H. Wentzler

Limestone is potentially a low cost material for the neutralization of acid mine drainage and other acidic waters such as steel pickling liquor. Unfortunately, when limestone is reacted wit9 these waters containing large amounts of Fe , Fe+3, and SO4-2 , a coating of gypsum and iron hydroxides form on the surface of the limestone inhibiting further neutralization reactions. The nature of these coatings, their morphology, composition and thickness were evaluated using the scanning electron microscope and microprobe, and the kinetics of limestone dissolution was studied both in the presence and in the absence of the reaction-inhibiting coatings. These data were then correlated with the solution chemistry.

Jan 1, 1992

By Edoardo Misano, Magali Schivre, Martino Semeraro, Alain Bochon

"INTRODUCTIONThe Laboratoire Souterrain de Modane (LSM) is an underground research laboratory located in the Western Alps on the French – Italian border. It is located in the middle of the 13km long Fréjus highway tunnel that links Modane (France) to Bardonecchia (Italy) in correspondence of the highest overburden of 1800m. The LSM current activity is mainly based on the investigations about the dark matter and requires very sensitive instrumentation which shall be protected from cosmic rays. To comply with the new legislation about safety in tunnels, the highway tunnels owners agreed in 2007 the construction of a parallel safety tunnel, at an average distance of 50m from the existing tunnel and the laboratory owner CNRS (Centre National de recherche scientifique) also decided to extend the existing laboratory with the construction of a new 17000 m3 cavern allowing the installation of wider and more powerful instruments that could increase chances of success of research. Preliminary studies stated that, considering both geological and functional issues, the most appropriate location for the new laboratory shall be in between the two tunnels and parallel to the existing laboratory (see Figure 1).Hence, the CNRS asked Systra, already in charge of the works supervision of the safety tunnel, to realize the design of the new cavern. The laboratory extension includes the construction of a 40 m long cavern with 300 m² cross section and two smaller tunnels connecting the safety tunnel and the existing laboratory to the new cavern. The minimum distance between the front face of the new LSM and the highway tunnel is about 25 m.The French and the Italian authorities, responsible of the exploitation of the Fréjus highway tunnel, asked the CNRS to develop an accurate study indicating that the construction of the laboratory extension would not have any negative impact on the existing structures of the highway tunnel. The main results of the developed study by Systra are summarized hereafter. The construction works should begin prior to the end of the construction works of the Fréjus safety tunnel in 2018."

Jan 1, 2016

By J. Ke

Traditional geostatistical methods have been used in ore reserve estimation for decades. Neural Networks (NNs) have provided an alternative approach to data analysis and ore reserve estimation. Unlike the traditional geostatistical methods, neural network uses a highly non-linear complex algorithm to do the estimation. Although Neural Networks have been demonstrated to be attractive alternatives as with every new techniques, there are questions which remain unanswered. This paper presents a comparative analysis with different types of metamodeling approaches -- Triangular, Kriging, Spline, and Neural Network. The neural-network is organized in a multiple-layers and Back-propagation model is used to handle the non-linearity and hidden slabs for smoothing the predicted results. With multiple dimensional and very noisy drill hole sample data, the ore grade is predicted and the overall performance is validated by the analysis of R-squared (R2), Root-Mean-Squared (RMS), and contours of ore grade spatial variability. The ore grade and tonnage of estimated outputs are also compared with various cut-off grades.

Jan 1, 2003

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By A. Kepeski

Cement industry relies heavily on the control of large volume of raw materials in the proximity of plant operations for clinker and cement manufacturing. These mineral resources are perhaps considered as ?low-profile? (mostly comprise limestone's, clays, marls and sands), but their availability, accessibility and suitability ? the later with respect to chemistry, mineralogical and physical characters ? are factors of paramount importance and may largely affect production cost and plant productivity. The combination of scarcity of good quality raw materials deposits and the growing environmental concerns have challenged the cement producers towards sustainability and the responsible exploitation of natural resources. In open pit mining and quarrying, the evaluation of mineral resources vs. handling of the non-usable overburden and other off-spec materials directly affects the medium to long-term production planning, quality control practices and environmental management. It is a general trend for many cement producers and a usual case for a number of Titan Cement plants worldwide, that redesign of quarry pits is necessary not only for stability purposes but also as a result of environmental constraints and emerging issues. The material reserves then have to be re-evaluated in the light of the new final pit design, safety distances from houses, other infrastructure and Law restrictions and according to criteria of safety of operations, reduction of environmental impacts, pit optimisation and proper future reclamation. The paper discusses the case of three active quarries of Usje Cement Plant, in Skopje (Macedonia), namely Usje (marl), Goverlevo (lime-stone) and Ljubosh (sand), where a large campaign of redesign and evaluation of recoverable reserves and the needs in rehabilitation took place in 2004. Technical and environmental issues and criteria are presented in the form of master plans and the highlights of the first attempts to propose and apply a reclamation scheme are discussed, by also examining alternative solutions for each quarry area. Finally, the 2005 progress in applying changes to the design of benches and pit layout, as well as experiences gained, are discussed.

Jan 1, 2005

By M. J. Virnig, Marc Le Vier, Rong Yu Wan, Jan D. Miller

Although most gold production from primary resources is achieved by cyanidation, many research activities have focused on alternative processes using noncyanide lixiviants. Such research has been prompted by environmental concerns and problems associated with the processing of refractory gold ores. Numerous research projects have been conducted to search for a noncyanide hydrometallurgical process for gold extraction. In this paper, a technical review of gold recovery from noncyanide solutions is presented, and new results are reported. Gold recovery techniques that are considered include activated carbon adsorption, cementation, solvent extraction, ion exchange, and reduction-precipitation.

Jan 1, 1993

By Corby G. Anderson, Sheikh Abdul Rezan Sheikh Abdul Hamid, Sanjith Udayakumar, Ahmad Fauzi Mohd Noor, Teuku Andika Rama Putra

Chemical and mineralogical characterization of Malaysian monazite, a phosphate mineral, bearing rare earth elements separated from the tin tailings originated from Ipoh, Perak, Malaysia, was performed in this paper. The study aims to collect detailed information on the chemical composition, crystal phases, and microstructure of the mineral monazite concentrate that would aid to optimize the subsequent hydrometallurgical processes for high-efficient separation of thorium and other associated rare earth elements. A systematic characterization study of the concentrate was conducted using techniques such as optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and Fourier-transform infrared spectroscopy (FTIR). These techniques analyzed the morphological details on the surface, elemental analysis, and mineral association assessment and identified the surface functionalization groups. The bulk composition and the mineral phases in which the elements are present were studied by wavelength-dispersive X-ray fluorescence (WD-XRF) and X-ray diffraction (XRD) studies respectively. The XRF analysis confirmed the presence of Ce, La, Nd, Pr, and Y (rare earth oxides: REO’s ~ 60 wt.%) while thorium dioxide (ThO2) accounted for 7 wt.% of the total composition. Traces of Ca, K, Al, Fe, Ti, and Mn were also confirmed by SEM elemental mapping. The XRD results confirmed that the concentrate was primarily composed of monazite (Ce, La, Nd, Th (PO4)) along with minor impurity phases of quartz. Automated mineralogical analysis was used as a confirmatory tool to corroborate the preliminary evidences. Based on the particle size distribution analysis supported by SEM, the majority of monazite grains were found to be present in the size range of 170–210 μm. Strong bands of PO4 and SiO4 were observed in the IR spectra corresponding to the phospho-silicate matrix of the REE mineral.

By Raj K. Rajamani, Samira Rashidi

Wear is an extremely important topic when considering high-pressure grinding rolls (HPGR) for any new application. Given the inevitable variations in ore properties throughout a mine’s life, it is difficult to predict the effect of material and operating conditions on the wear parts: specifically, the HPGR rolls. However, the possibility of continuous scanning of rolls provides ample information to review the wear pattern and ways to optimize it. In this regard, as part of a broader investigation, the feasibility of in-line scanning of HPGR rolls in a laboratory-scale HPGR is studied and presented. The choice of scanners and methods adopted to achieve high-level accuracy for determining wear is discussed in this paper, and the inherent variability affecting the measurements is evaluated. 

By Carl Erickson, James Hislop

INTRODUCTION As practiced today, longwall mining is a mechanical version of an established mining system. The equipment for longwall mining consists of four basic units: roof supports, face conveyor, winning or mineral-getting ma¬chine, and stage-loader conveyor. The system mines relatively thin slices of mineral across a predetermined face length in a virtually continuous sequence. As the winning machine cuts, the mineral is loaded automatically onto the face conveyor. In turn, the face conveyor is pushed over into the newly cut track by hydraulic rams attached to the conveyor and the roof supports. The roof supports then are lowered individu¬ally from the roof, advanced to the repositioned con¬veyor, and reset to the roof. At the end of the pass, the longwall cutter is pushed over, and a slice is taken in the opposite direction, so the system repeats itself. Fig. I illustrates a typical longwall mining system. The principle behind the longwall mining system is that the roof is supported only immediately adjacent to the worked seam, keeping the blocks of immediate roof clamped securely from the face to the rear of the sup¬ports. At the rear of the supports, the roof is allowed to fall and break up, with the swell of the broken material eventually establishing an equilibrium in the strata be¬hind the mined area. Fig. 2 illustrates the principle of longwall support. There are two distinct types of longwall mining. The longwall retreating system is the most common in the United States, South Africa, and Australia. The longwall advancing system is the most common in the re¬maining industrialized countries such as Britain, Ger¬many, Poland, and the Soviet Union. The longwall retreating system comprises a mining panel, where the roadways that form the head entry (end at which mineral is delivered from the face con¬veyor to a stage-loader conveyor) and the tail entry are predriven before the longwall units starts production. In the longwall advancing system, the longwall unit makes the head and tail entries as the face advances, utilizing various techniques to prevent the entries from being destroyed as they are left in a consolidating gob area. Fig. 3 illustrates the comparative approaches of the longwall retreating and advancing operations. As with most other underground mining systems, there are many variations on these two basic systems, using combinations of the systems that are dictated by

Jan 1, 1982

By K. T. Brashear, N. Ripepi

"Over recent years, specifically following the MINER Act of 2006, an increasing number of manufacturers of underground mine seals in the United States have begun using a form of pumpable cement or shotcrete to create barriers separating the working and abandoned sections of underground coal mines. This seal material, while generally considered to be homogenous and solid, contains a network of microcracks, voids, and delaminations. Generally, it has been assumed that methane (CF4) leakage around these seals is a result of movement around the boundary interface between the seal and surrounding strata. Using a perfluorinated tracer compound, perfluoromethyl-cyclohexane (PMCH), the movement of gases can be monitored through seal material to observe how gases move though the material, both intact and with faulting in the material. This paper documents two large experiments where the movement of PMCH was monitored in the field, along with modeling confirmation using 3D visualization software. INTRODUCTION According to a report in 2007, there were over 14,000 active mine seals in underground U.S. coal mines alone (Zipf, Sapko, & Brune, 2007). These seals are used for both ventilation and safety purposes, to direct the flow of air away from the abandoned area of the mine and to help eliminate the propagation of explosions that can occur on the outby side of the mine seal. The atmosphere on the outby side of these seals typical consists of low levels of methane that have the potential of producing leakage along the face of the seal on the inby side. Methane leakage around mine seals has historically been attributed to the permeability between the seal and mine interface (McPherson, 1993). According to the United States Bureau of Labor Statistics (BLS) between 2003 and 2012 an average of 17 deaths occurred annually in underground bituminous coals mines. The only time during the ten-year period where the fatalities were higher than the average was in 2006 and 2010, years which had three major explosions occurring in underground coal mines in West Virginia and Kentucky. Two of the explosions were propagated through the mine by seal failure or methane leakage around newly poured seals (Light, et al., 2007) (Gates, et al., 2006). These recent events, and new regulations regarding seal strength (MINER Act), have created a need to monitor the condition of underground mine seals. BACKGROUND Measuring the permeability of solid materials, such as concrete or seal materials, can be a valuable tool in the field of non-destructible testing (NDT). By using an inert gas, such as nitrogen, injecting the gas into a solid structure, and measuring the resultant flow rate and pressure differential, this can provide valuable information about the structure. Studies have shown permeability can be affected by the stresses applied to the structure, as well as temperature and moisture (Choinska, Khelidj, Chatzigeorgious, & Pijaudier-Cabot, 2007) (Abbas, Carcasses, & Olliver, 1999)."

Jan 1, 2015

By J. Herbst, C. C. Harris, G. Poling

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale- down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

Jan 1, 1999

By W. H. Andrews

DEFINITION OF BAUXITE The term "bauxite" (1) dates back to 1821, when it was assigned to a deposit of red earthy material outcropping near the village of Les Baux in Southern France. Chemical analysis indicated the presence of aluminium oxide, iron oxide and water. Deposits of bauxite are widespread throughout the world although the major developments occur within 30 degrees of the Equator. Essentially bauxite is the product of weathering and leaching of a variety of sediments or rocks, generally in a high-rainfall tropical or sub-tropical climate, resulting in the enrichment of the aluminium oxide content. It is characterised by the presence of one or more of the minerals, gibbsite, boehmite, and diaspore. The other constituents are usually clay, (typically kaolin), hematite and/or goethite (iron-oxides), anatase (titanium oxide), and possibly silica as quartz. A variety of minor elements may be present, such as calcium, magnesium, phosphorus, vanadium, gallium, manganese, and many others in very small quantities. Organic compounds are normally present from development in association with a soil horizon where vegetation may be encouraged by the high rainfall necessary for bauxitisition. The physical form depends upon the geological history of the deposit and correlation also exists with the mineralogy. Older deposits which have been subject to burial are invariably hard and compact with the alumina predominantly occurring as boehmite or diaspore, while the more recent, surface deposits are frequently less compacted and gibbsite is the dominant alumina mineral. In these later deposits, the physical form can vary from the fine red soil (terra rosa) of Jamaica to the Weipa pisolites to the cemented Arkansas type. The presence of concretionary structures is an important aid in identification in the field.

Jan 1, 1984