Search Documents

By Zygmunt Sadowski

Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of chemical additives and metal ions present either added or present as contaminants, on the flotation. Fuerstenau and Palmer (1976) have studied in detail the adsorption of multivalent cations onto oxide and silicate minerals. It was observed that the adsorption of a multivalent metal species exhibits a sharp pH dependence which is related to the formation of hydroxy complexes of the metal ions in solution. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances cations such as Ca2+, Mg2+, Fe2+ and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions.

Jan 1, 1986

By K. A. Natarajan

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration, namely, nitrogen, air and oxygen on ball war was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. 'Marked ball grinding, tests along with electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen towards wear (corrosive wear) is relatively small and abrasive wear appears to be significant. Rheological properties of the slurry-appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1983

By D. Spitty

There are enormous complexities with mine planning and the problem itself presents a huge challenge to the existing mine planners performing this activity. Mine planning optimization supports planners to determine ?What are the best increment excavation sequence and the best material blending combination such that throughput, quality, cost, utilization and Net Present Value (NPV) targets are met?? It is achieved through using an advanced scientific approach that has been specifically adapted to address the mine planning dilemma.

Feb 23, 2014

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

High pressure grinding rolls have found widespread acceptance for cement processing, and are now making their debut in the metalliferous minerals industry. Significant energy and wear material savings appear achievable in many applications. This paper re- views the technical literature on this important, emerging technology.

Jan 1, 1997

By L. C. Atkinson, E. A. Azrag, T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is a more realistic simulation of the problem, but the former method is significantly easier to use. Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.2 to 0.6. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1995

By L. W. Ashton

Geochemical exploration guidelines were developed from a study of 460 rock chip samples collected at nine disseminated gold deposits in Nevada. Obtaining high grade Au samples is difficult because gold content is extremely variable, even over 8 m (25 ft) distances. For reconnaissance sampling, pathfinder elements are reliable indicators with threshold values of 100 ppm As, 1 ppm Hg, and 50 ppm Sb. Arsenic is the most reliable of the three elements, being significantly enriched in all deposits. If the pathfinder threshold levels are reached with low Au content, more samples should be collected. Successful disseminated gold exploration requires large numbers of samples.

Jan 1, 1990

By Kenneth S. Johnson

Iodine, a grayish-black nonmetallic element, with a density of 4.9 g/cm3, is a solid at ordinary temperatures. It is a member of the halogen family, along with fluorine, chlorine, bromine, and astatine. Iodine melts at 114°C. and at 184°C it is volatilized to a blue-violet gas that has an irritating odor. It does not occur as an element in nature, but occurs as iodates, iodides, or other combined forms. It is the 47th most abundant element in the earth's crust. Iodine was discovered by Bernard Courtois in 1811. He observed an unknown substance in the crude soda ash that results from the burning of seaweed. Samples of this unknown substance were identified to be a new element, and in 1813 Gay-Lussac named the substance iode, from the Greek word for violet color. The world production during 1989 and 1990 [(Table 1)] is estimated to be about 16 million kg per year (Lyday, 1991), of which about 30% is consumed in the United States. GEOLOGY AND MINERALOGY Compounds of iodine are minor constituents in seawater and brines, in certain marine organisms, and in minerals of the Chilean nitrate deposits. Seawater contains approximately 0.05 ppm iodine, and certain marine organisms, such as seaweed, sponges, fish, and some brown algae, are able to further concentrate iodine (Lyday, 1989a). Some seaweed can extract and accumulate iodine up to 0.45% of their weight, on a dry basis. The northern Chilean nitrate deposits, in the Atacama Desert, contain the following iodine minerals: lautarite, Ca(I03), (calcium iodate); dietzeite, CaJIO,), (CrO,) (calcium iodate-chromate); and bruggenite, Ca(I03), . H20 (Erickson, 1981). Various subsurface brines also contain iodine compounds. Some gas-field brines in the United States and Japan locally contain 30 to 1 300 ppm iodine. Several coals in Germany also contain iodine compounds. Iodine has been recovered from brines mainly in Japan and the United States, but also in Java, Indonesia, Italy, England, and the former USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. Seaweed was a major source of iodine for the world in the first half of this century, and it remains as a large resource. The reserves and future resources of iodine are large, even excluding the resources in seaweed and seawater, and are shown in [Table 1]. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable. PRINCIPAL PRODUCING COUNTRIES Major iodine-producing nations are Japan, Chile, the USSR, and the United States, with lesser amounts being produced in China and Indonesia ([Fig. 1; Table 1]). Annual world production in 1989 and 1990, respectively, is estimated at 15.6 and 16 million kg. In Japan and Chile, the production of iodine depends on production of other materials, such as natural gas or nitrates, respectively, whereas in US operations (in Oklahoma) iodine is the major product recovered from natural brines. Chile was for a long time the principal world producer of iodine from its nitrate-fertilizer operations, but in recent years Japan has become the world leader with increased production of natural gas and associated iodine-rich brines.

Jan 1, 1994

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By J. M. Keating, R. L. Wiegel

Those processing plants which depend on flotation for their mineral separations are always looking for reagents which are cheaper, more selective or in some other way may provide improved economic performance. This paper describes the rationale for and some results from applying a statistically based approach to reagent testing in those flotation plants which still rely on experienced operators for manual flotation control.

Jan 1, 1986

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By Rick Bearce, Minsu Cha, Mike Mooney, Yuanli Wu, Lisa Mori

"Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. Chamber pressures can reach 3-5 bar yet the vast majority of testing is performed under atmospheric conditions. This paper illustrates how pressure influences foam stability and conditioned soil behavior, and how atmospheric test results must be viewed in the context of expected chamber pressures. Torsional shear strength, compressibility and abrasivity of foam conditioned sand were found to be ideal when the void ratio was above the ASTM-determined maximum void ratio, achieved by sufficiently expanding the soil grain structure with foam, herein when the foam injection ratio at pressure exceeded 45%. Otherwise, the engineering properties of foam conditioned sand were not ideal, i.e., appreciable torque and abrasivity, low compressibility. INTRODUCTION Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. The formation soil at the cutterhead must be transformed into a highly compressible, low shear strength and low permeability medium within the excavation chamber to allow effective EPB performance. This behavior must be maintained for a certain residency time while the soil is in the chamber and screw conveyor. The vast majority of published studies on conditioned soil behavior have been performed under atmospheric conditions (Quebaud et al., 1998; Bezuijen et al., 1999; Psomas and Houlsby, 2002; Vinai et al. 2008; Thewes et al., 2012; Peila, 2014); however, the desired soil behavior must occur under chamber pressures that can reach 5-7 bar. The influence of pressure on conditioned soil is significant and is dramatically different than behavior under atmospheric pressure (Williamson et al., 1999; Mori et al., 2015). This paper illustrates how pressure influences conditioned soil behavior and how atmospheric test results must be viewed in the context of expected chamber pressures. The influence of pressure on foam bubble size (including with time) is shown through digital image analysis. The influence of pressure on foam half-life is also investigated. The compressibility, shear strength, and abrasivity of conditioned soil under pressure is presented and explained in terms of density, soil and air compressibility and porosity."

Jan 1, 2016

By Kirk L. Prather

Why discuss techniques of accident prod lot on? Would it not be more useful to discuss means to reduce accidents? This discussion will answer these questions by suggesting ways in which effective accident prediction techniques improve the ability to foresee and prevent accidents. Accident Prediction Process The secret to accident prediction is to utilize the tendency for history to repeat itself. The same circumstances and the same human behavior that produced accidents in the past tend to produce accidents in the present and the future. The ability to predict accident occurence in the future by projecting from the past is a statistical process. In a bookmaker's jargon this means "playing the odds" or "the percentages". A horse or a sports team may be beaten on any given day, but by skillfully assessing the factors of past performance and assigning odds, many clever bettors make money in the long run.

Jan 1, 1973

By M. S. Prasad

In earlier work it has been shown that paper filler clay products can be obtained from primary kaolin deposits of Minnesota. The objective of the current work was to reduce silica and iron contaminants and to maximize kaolin recovery to higher value products suitable for paper coating. This results in achieving a finer and cleaner product conforming to paper coating specifications. Cationic flotation and high gradient magnetic separation were used to remove free silica and iron, respectively, while attrition grinding and ultrasonics have been examined for particle size reduction. The results of this work are presented and discussed particularly with respect to application-oriented product properties. Budgetary estimates are presented for a 200,000 ton/year processing plant based on the process flowsheet developed and optimized by the study.

Jan 1, 1991

By W. J. Roberds

A formal and explicit yet cost-effective approach is proposed to ensure that decisions made during mine development are optimum (with respect to their ultimate consequences) as well as defensible. This risk management approach is based on probabilistic risk assessment and established decision analysis techniques, and appropriately considers the relationships among various mine development decisions, tradeoffs among consequences, the uncertainty in predicting consequences, and the benefits of flexibility to respond to changed conditions.

Jan 1, 1992

By Richard Klimpel

The laboratory ball mill grinding of coal/water slurries is described for three coals. Emphasis is placed on the measurement of specific rates of breakage for various operating conditions. Corresponding rheological information is also presented based on data collected using a rotational viscometer. A rheological explanation of the influence of various slurry fluidity conditions on the specific rates of breakage is presented. This rheological approach has proved useful In both the identification of suitable chemicals for increasing breakage rates in coal/mineral slurry grinding and in the plant scale implementation of dense slurry grinding systems.

Jan 1, 1982

By Paul H. Rydlund

The wide use of bulk ANFO in surface coal mines is questionable in our energy conscious environment. At many locations, bulk ANFO is not the proper economic selection. Water conditions, energy requirements, waste and spillage, and vibration control are factors too often overlooked in the proper choice of blasting agents. Cost savings over 20% have been realized by converting bulk ANFO to packaged blasting agents. Future trends suggest greater concern for energy conservation in blasting will limit bulk ANFO applications and promote packaged products where quality can be maximized, waste and spillage eliminated, and water compatibility in wet areas assured.

Jan 1, 1980

By Y. G. Zhang

Interactive Dynamic Optimization Method (IDOM) will be presented in this paper. IDOM combines inventory theory, dynamic programming, computer simulation and interactive technique to formulate a production schedule for open-pit mines. This new method has been successfully used in metal mines of China for years.

Jan 1, 1986

By Zoheir Khademian, Gabriel S. Esterhuizen, Morgan Sears

Based on the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accident in the US longwall mines were caused by gateroad roof instability. This can be related to the significant changes in loading conditions that gateroads are subject to from the development to the longwall abutment loading phases, combined with the thinly bedded shale roof, found in many US longwall coal mines. One of the challenges in designing efficient support systems is to understand the roof instability mechanisms along with support-roof interactions under this complex loading condition. Field monitoring of roof displacement and stress changes coupled with detailed analyses using numerical models are well-documented techniques to study the causes of roof instabilities. However, traditional modeling techniques require additional calibration to simulate delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. One alternative modeling technique is the UDEC Bonded Block Method (BBM) where bedded roof and support interactions can be explicitly captured. This paper presents the development of a BBM model of a longwall entry at a 180 m depth of cover with a three-entry gateroad layout along with roof extensometer monitoring results. The models are validated against the monitoring data, showing the potential for BBM numerical models capturing the complex roof and support system interactions to assist with optimizing gateroad layouts and support systems.

By Meili Zhu, Qingpu Shi

High temperature, methane, dust and other disasters are getting more serious with mining depth getting deeper and the development of mechanization in underground mines. An application of a descensional ventilation to a coalface is one of the effective measures to solve the above problemes. The descensional ventilation is an venttilation that an airflow in a coalface wouuld downflow along an inclination of a coalface and the direction of the airflow is the same as coalflow. Since 1960's, the descensional ventilation has been applied to 171 coalfaces in 46 coal mines of 23 coal mine administrations in China, such as Pingdingshan , Zhongliangshan, Pubai, Huangshi coal mine administrations. Among the 171 coalfaces, there were 104 coalfaces taking 60.8% in gently inclined seam. The coalfaces in inclined seam and steep seam were individually taking 18.7 % and 20.5 %. There were 77 coalfaces taking 45 % of the total in low gassy coal mines and coal and methane outburst mine were individually taking 17% and 38%. There were 141 coalfaces taking 82.5% of the total in potential danger of dust explosion. There were 125 coalfaces taking 73.1% of the total in potential danger of spontaneous combustion. Therefore, the descensional ventilation can be used in coalfaces under different conditions in China. The practice at home and abroad shown that the application of the descensional ventilation to coalfaces has obvious results in dust control, temperature control, preventing methane accumulation at top corner angle and control of spontaneous combustion in goaf. To more safely and reliably apply the descensional ventilation to coalface and to provide a way for the development of mine ventilation technology in China, the paper will have discussions on the following problems: METHANE EMISSION AND DISTRIBUTION AT COALFACE WITH DESCENSIONAL VENTILATION Methane emission in a coalface with a descensional ventilation is an argued issue for many years. Base on the coal practice, special similar model tests and researches in China, the followings are our main comments. The Descensional Ventilation can Reduce the Methane, Accumulation at the Top Corner Angle. The measurements in six coalfaces with the downward airflow in Qinhemen Mine, Fuxin Coal Mine Administrations shown that the methane concentration at the top corner angle is often up to l% when the coalface has the upward, airflow. The max. methane concentration at the top corner angle is about 0.49 to 0.7% when the coalface has the descensional ventilation. Therefore, with the descensional ventilation, it basically solved the overlimited gas concentration at the top corner angle which is a potential danger to coal production. Because the direction of upfloating gas is opposite to the direction, of the descensional airflow, the descensional ventilation; could increase a turbulent flow mixing capacity of the methan gas and air, and reduce a possibility of methane; accumulation. Due to an air leakage in goat when the coalface with the descensional ventilation lower than an air leakage in goat when the coalface with the, ascensional ventilation, a less methane quantity will release from goat at the descensional ventialtion. It should be pointed out that due to a higher air leakage at ascensional ventilation and the direction of the air; leakage same to the direction of the natural upfloating methane in goaf, those will cause a large methane; accumulation at the top of the goaf and easy bring about, methane accumulation and overlimited methane concentration at the top corner angle with an ventilation vortexflow at the top corner angle. On the other hand, because the direction of the upfloation force function is upward, the descentional ventilation could minimize as possibility of methane accumulation at top corner angle in coal with the descensional ventiltion.

Jan 1, 1991