Search Documents

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997

By P. L. Dunn, G. T. Adel, E. B. Cruz

Automatic control of fine-coal cleaning circuits has traditionally been limited by a lack of adequate sensors. Although several nuclear-based analyzers are available, none have seen widespread acceptance. In this investigation, image analysis is used for the on-line determination of ash contents in fine-coal slurries. The ash content of a flotation tailings stream is correlated to the mean gray level of the slurry. Based on a 90% prediction interval, an analysis of sensor performance indicates an accuracy of 73[±] 4% ash over a range of from 65% to 90% ash. While the results are comparable, the video-based system costs only a fraction of what a nuclear-based analyzer costs. The sensor is now installed at the Middle Fork preparation plant, which is owned by Pittston Coal Co.

Jan 1, 1999

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

By L. B. Phelps

Current mining regulations require revegetation in reclaiming surface nines. Excessive soil compaction can be an impediment to successful revegetation in poor soil conditions common to Eastern coal nine sites. A field study was performed to determine the bulk densities of soils that had been spread by either bulldozers or scrapers at a strip nine site. Moisture-density relationships for the soils were determined from the field samples. These were compared with stockpile samples compacted by the Standard Proctor compaction test. The results of the study indicate that the degree of compaction could be lessened through proper soil handling procedures.

Jan 1, 1986

By H. E. Rojas

The primary objective of most comminution operations is liberation; however, mill performance is generally quantified in terms of particle size. Only recently has the use of image analysis equipment made it possible to quantify mill performance on the basis of liberation. In this investigation, a series of tests were carried out to study the effect of mill operating parameters on the liberation of sphalerite from a sphalerite/dolomite ore. The parameters studied included mill rotational speed, mill loading and ball size. The results of this work appear to indicate that sphalerite liberation is improved under conditions that promote impact breakage, while dolomite breakage is enhanced under attrition conditions.

Jan 1, 1990

By Mark C. Williams, Thomas P. Meloy

Particle shape characterization is a complex task made more difficult because of the human eye's sophisticated recognition of shapes, giving rise to the assumption that shape analysis is considered a simple problem. Further exacerbating the problem is the question of whether particles have a general shape. Old and new shape measuring techniques are discussed, particularly the new image analysis methods techniques such as Fourier, Haar, Walsh and Delta. Problems with the current image analysis equipment and future research equipment needs are presented.

Jan 1, 1989

By George M. Anderson

The extraction of industrial minerals is usually confined to relatively small mining operations. The recent COSMAR (Committee on Surface Mining and Reclamation) report found that 93% of all mines in the United States were of the small unit variety. Also, of the total number of mines in the U.S. (15,279) 96% were in the industrial minerals (non-metals excluding coal) category. To break it down further, 86% were sand and gravel, and crushed stone operations. Therefore, we are talking about a very large number of small mining operations. If these small miners can afford to hire a college graduate, what kind of training should this person have beyond the normal mining engineering curriculum to best serve the problems that he or she will encounter?

Jan 1, 1981

By M. D. Flavel

My paper relates to bond's third theory of comminution and suggests work be used as a basis for designing crushing and screening plants, this will give more accuracy than existing methods, As stated in the abstract, this paper is only a synopsis of my official paper, many of the questions that might arise in this brief address will be answered by referring to the detail i n the main paper $ Because of the limited time available and the fact that many people here do not need to study the aspects of crushing and screening in depth, i will highlight-those sections of the paper which show how major capital, operating and energy cost savings can be achieved in the process, I will develop the theme in the following manner, Firstly, pointing out, why a new approach is needed to the fundamentals of crushing and screening, Secondly, by setting forth some theory to describe what we are trying to accomplish, Thirdly, by looking at important factors which need to be observed in designing plants and applying machines to comply with this theory, Lastly, i will put forth some ideas on how we might develop this theory to make the industry more efficient, At the outset, i have to say my approach to this process is entirely new, for those used to applying machines and designing plants on existing criteria, they will find this theory easier

Jan 1, 1977

By Crone Duncan

The search. for massive sulphide orebodies is steadily being extended to greater depths as well as expanding outward into the large portion of the earth's surface where the sulphide bodies are deeply weathered. Massive sulphide orebodies are generally not large in dimensions. They are not like disseminated type sulphide bodies that form large ground exploration targets that can be detected at greater and greater depths simply by increasing the geometrical spacing between the geophysical transmitter and receiver. In¬creasing the transmitter-receiver spacing with massive sulphide bodies eventually "waters down" the anomaly from the body until it disappears into noise. If high surface conductivity is present, as is common in areas of deep weathering, the problem is compounded by the increasing response of the surface layer, as the receiver-transmitter spacing is expanded. The search to greater depths has important implications other than just detection of the orebody. Drilling costs are increased and the probability of missing the target are increased. Missing an orebody is an expense that is difficult to evaluate in dollars per line mile of survey especially since one does not know the value of what was missed. A ground Pulse EM method has the capabilities of solving the problems of deeper exploration particularly in areas of surface weathering it can attain deep penetration without large coil spacings, it also provides information from a complete range of frequencies. The method has other operational advantages since it is free of geometrical restrictions as to coil alignments and can operate in areas of high power line noise.

Jan 1, 1975

By A. M. McKim

6, 7.3 meter diameter autogenous mills at Wabush Mines are undergoing conversion from a radial configuration of pulp discharger to a curved design. Improved discharging efficiency has effectively lowered the pulp level in the mill. The low level operation enhances the grinding efficiency netting a 12% power reduction. Significant reductions to rate of wear has been a spin off benefit. The design incorporates features for holding the assembly solidly in place thus eliminating bolt hole damage and leakers. Preliminary work in one 11 meter mill at Hibbing Taconite did not indicate that all the same advantages were available in their process.

Jan 1, 1982

By F. J. Susko

The U.S. Bureau of Mines is using Fourier-transform infrared (FT-IR) analysis to investigate the bonding mechanism which occurs during the dewatering of clay slurries. High molecular weight polymers are used as flocculating agents in these processes. This investigation presents the results of an FT-IR study of calcium-exchanged montmorillonite treated with polyacrylamide (PAM) and polyethylene oxide (PEO). Both thin film and attenuated total reflectance (ATR) spectroscopic techniques were employed to study this clay-polymer system~ Results suggest PAM is adsorbed to the clay via the nitrogen atom of the polymer. A water bridge is involved in the bonding between the clay and PE~. Evidence also suggests that PEO may be adsorbed directly onto the surface of the clay.

Jan 1, 1990

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By S. Mathur

Polyacrylic acid (P AA) was evaluated as a selective flocculant for dolomite-apatite system. P AA of 4 million MW was found to flocculate both dolomite and apatite. However, their flocculation behavior was significantly different with 450,000 MW PAA which was the lowest molecular weight fraction capable of flocculation. In single mineral tests, at a dosage of 2kg/t 90% of dolomite and 35% of apatite flocculated. Selectivity was achieved in mixed mineral tests where apatite of 90% grade at 70% recovery level was obtained in the concentrate from a feed consisting of 80:20 mixture of apatite and dolomite. The dolomite rejection was about 75% which corresponds to 1% MgO in the concentrate.

Jan 1, 1995

By J. J. Harrington

The pH control system at Kennecott Copper Corporation's Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a two-minute repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaining a limited maxi- mum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1975

By Charles W. Daugherty, Robert Nyren

The replacement of Boston’s elevated Highway I-93 running north to south through the heart of the city with 8-lane tunneled roadways, coupled with the underground extension of Highway I-90 eastward to Logan Airport, has earned the Central Artery/Tunnel (CA/T) Project the position of the largest infrastructure project in the U.S. today. The gigantic interchange featuring numerous ramps where these two main branches of the Artery intersect required the construction of three huge jacked tunnel boxes that were pushed beneath eight active Amtrak and commuter rail tracks that had to remain undisturbed in spite of poor geology and a minimum of cover between the track beds and the tunnel crowns. Ground freezing was chosen as the method of stabilizing the soil over the tunnels, and it was extended in one area to stabilize the ground at the intersection between the tunnels and an abutting deep cut-and-cover excavation. Because many standard geotechnical instruments consist basically of open standpipes filled with water, it was a major challenge to keep them de-iced and in a condition to provide data on vertical and lateral ground movements. The efforts to do so are herein described.

Jan 1, 2003

By Bee R. Waples

The Alimak Raise Method, using the Alimak Climber, has proven to be a new, fast, economical method of driving raises at the Iron King Branch of Shat-tuck Denn Mining Corporation, Humboldt, Arizona. In order to fully understand the advantages of the Alimak Raise Climber, it is necessary first to describe the basic machine; second, a complete cycle of a raise round; and third, the comparative speed and economy afforded the Iron King operation by using this new method of raise driving: The raise climber consists of a drilling platform that is raised and lowered by two 6.2 HP compressed air motors that drive, through roller chains and sprockets, three worm gears connected in series. These worm gears drive pinions which grip the guide rail rack. The worm gems are fitted with spring-loaded couplings so that a small rock or grit in the rack is passed over without disturbing the mesh between the rack and the other pinions.

Jan 1, 1961

By Fun-Den Wang

In underground coal mines, three types of roof failure (2)*, tensile, local, and shear, occur in the development entries and in room-and-pillar extraction areas. Most of the tensile failures in the roof at the center of the mine opening as well as those local failures due to fracture or jointing can be controlled by roof bolts, trusses, and timbering. However, control of the shear failure at the sides of the roof (or the cutter-roof caving) has not been successful with ordinary roof control methods. The only effective method, when there is an indication of cutter-roof caving, is to use cribs, which are costly and make transportation, ventilation, and production difficult. Frequently, the operator allows the cutter roof to cave and then cleans it up rather than trying to stop it. This shear type of roof failure is often associated with large areas which may progressively involve several hundred feet of roof caving at one occurrence. At times, this shear failure occurs suddenly with little or no warning. This can result in buried equipment and great danger to the safety of personnel. This shear failure may be due to one or more of the following: high stress concentrations at the corner of the roof from (1) high horizontal to vertical load ratio, (2) orthotropic elastic properties of rock and coal, (3) greater stiffness of the immediate roof layer than of the secondary roof layer, (4) viscoelastic behavior of rock and coal, and (5) geometry and material properties of the geologic setting. Removing or reducing the high stress concentration should improve the roof stability. The structural analyses of models of two typical

Jan 1, 1972

By James E. Palmer

Geologic constraints on mining and recoverability include the following: coal seams too thin or thick for conventional mining methods; coal seams with insufficient stratigraphic separation; unstable roof or floor strata; discontinuous or lenticular seams; coal seams that have high dips or are intensely faulted; water problems due to proximity of aquifers; and coal quality problems such as excessive sulfur, ash, chlorine, sodium, etc. The demonstrated reserve base for western coal of 220 billion tons is considered misleading as it does not adequately incorporate the above parameters in estimating procedures. Current reserve base estimating procedures involve an abstraction of data from generalized resource estimates. The authors believe the reserve base should be determined independently beginning with well-known deposits, with all mining and recoverability constraints fully incorporated.

Jan 1, 1981

By P. James

"INTRODUCTION Dissolved salts build up in leach solutions over time as leach solutions mature. Iron can be particularly problematic for hydrometallurgical copper production as it can compete with copper for separation during solvent extraction (SX), leading to iron bleed through and reduced electrowinning (EW) efficiency. In its ferric form (Fe+3) it precipitates as a hydroxide at fairly low pH and can promote clogging and disrupted flow within leach pads as a result of localized pH deviations – such as might result from weather events. The solids formed can cause relatively irreversible degradation to pad productivity. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. Control of ferric (Fe+3) levels could be used to lower ferric (Fe+3) levels and keep the ferric hydroxide [Fe(OH)3] precipitation pH sufficiently high to avoid the associated solids formation and potential leach pad occlusion. Control of ferric (Fe+3) and ferrous (Fe+2) tenors and ratios may also provide benefit for improving sulfide ore leaching or bioleaching performance and effectiveness. Traditionally options for such control were rather limited with bleeding contaminants off or chemical dosing treatments being prominent methods. Now Blue Planet Strategies introduces a new option. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DeMet™ (Dynamic Electrolytic Metal Effluent Treatment) platform is highly effective at efficient low-cost conversion and control of iron content in leach streams in addition to targeted dilute metal recovery.[1-6] This powerful new capability provides a new treatment opportunity to control leach solution ferric (Fe+3) and ferrous (Fe+2) tenors to enhance leach operation production."

Jan 1, 2015

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993