Search Documents

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

To generate a most profitable ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1990

By M. Wasel

The Gross Rosebel gold deposits are located in the Guiana Shield of north central Suriname. Initial discovery of surficial gold in 1880 by local artisanal miners preceded small-scale mechanized mining from 1885 to 1939. The first systematic exploration program was carried out by Placer Development from 1974 to 1977. In May 1992 Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling based on information from surface mapping allowed development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. In a complex geological setting, the key to success at Gross Rosebel was persistent, systematic exploration, detailed mapping, careful core logging and perceptive geological interpretation. Reserves now stand at 48.6 Mt at 1.6 glt Au, or 2.4 million ounces of gold. The purpose of this paper is to describe the progression of exploration activity that led to the definition of substantial gold reserves and to summarize the geology of the deposits.

Jan 1, 1998

By S. E. Phillipson

The MSHA Technical Support, Roof Control Division's primary evaluation tool for coal pillar designs is the Analysis of Coal Pillar Stability (ACPS) program. However, ACPS is limited to evaluating interactions between two seams at a time, which is not ideal for complex multiple- seam scenarios. Further, it does not recognize the influence of strata properties in the interburden and cannot be used to evaluate individual pillars. We apply the Rocscience RS2 two-dimensional finite element program as a complement to ACPS. Complex multiple-seam scenarios can be characterized by a modified pillar stability factor where the ACPS single-seam development pillar stability factor is multiplied by the ratio of average single-seam development stress to the stress in the critical pillar at the multiple-seam stage, using the values of o as predicted by RS2. Several series of test examples involving two-seam analyses with isolated remnants, gob-solid boundaries, and high extraction areas of varying width were used to calibrate simulated gob properties such that the ACPS+RS2 method generated results that matched a traditional ACPS Stability Factor to within 13%. As high-extraction areas become wider and deeper, progressively stiffer gob is simulated by increasing the Young's Modulus property in RS2. After achieving calibration with the test series, three examples of complex multiple-seam scenarios were evaluated, using reasonable properties for strata types and thicknesses based on core log data. Resulting modified stability factors are reasonably close to those predicted by ACPS, although affected by units of sandstone in the interburden and gob shadows superimposed on remnant structures. This tends to show that even in complex multiple-seam conditions, applying ACPS to the worst-case interaction should usually result in an acceptable pillar design.

Jun 25, 2024

By Edward F. Nagle

Instrumentation engineers have recently devised practical methods of metering the net solids flowing in a hydraulic mixture. The solids flow rate is determined by measuring the specific gravity and the flow rate of the mixture. T e specific gravity is measured by a variation of the bubbler system. The flow measurement is made by a somewhat unorthodox orifice requiring field calibrations. The linear mixture flow signal is then multiplied by the specific gravity signal, which is directly proportional to the percentage of solids in the mixture, to produce a linear solids Slow rate signal. The computations in this system are performed by Sorteberg pneumatic relays. Having obtained this measurement, integration and automatic control of hydraulic solids flow are available. This system is useful in mining, drilling and dredging industries. It provides maintenance of the net solids flow rate and reduces power consumption. Automatic control will provide rapid stabilization of net solids flow rate and release operators from making menual adjustments. The advantages of this application are economy of operation and increased pump efficiency, This paper describes a hydraulic solids flowmeter system installed aboard a dredge. Its purpose is twofolds:- 1. 20 provide a summation of the net solids flowing 2. To make available a practical guide for the drag tender operator. (Dwg. GSD-2219)

Jan 1, 1958

By T. Rudolph, M. Pawlik, J. Benndorf, X. Yin, J. F. Brune, P. Goerke-Mallet

The long and often undefined period in the post-mining phase challenges geo-monitoring with its various responsibilities, like the detection of environmental changes, ground movements and water management. Modern methods of geo- and environmental monitoring observe numerous aspects using active and passive sensors with multispectral, hyperspectral and microwave sensors, with diverse spatial dimensions and spatiotemporal resolutions from satellites, Unmanned Aerial Vehicles (UAVs), in-situ sensors. Data integration, together with on-site knowledge and experience, provides the basis for comprehensive modeling, which improves the understanding of the environmental changes and their related causes, which is an essential step for public acceptance. In this paper, we aim to give a brief overview of various geo- and environmental monitoring methods.

Mar 2, 2022

By R. Bruce Sheibach

The Picher Mining District, located principally in north-eastern Oklahoma, was one of the world's largest lead-zinc mining areas during its 55 year life. The field covers an area of approximately 72 square miles (186 km.-); an estimated 1.6 x [103 yds3 of material (1.22 x 103m3)] worth in excess of one billion dollars, has been mined. Mining activities were typified by surface exploratory drilling identifying ore distribution and extension of underground workings to the lead and zinc deposits outlined. Exploration holes were either left unplugged or plugged at the surface with a section of a telephone pole. Low grade ore and waste rock were discarded in mined out portions of drifts. These waste piles containing pyrite and marquisette were left underground and oxidized during the many years of active mining. Upon cessation of mining activities in the mid-1960's, the drifts and shafts of the abandoned workings began to flood as the cone of depression filled in, leading to the dissolution of the oxidized sulfides and the formation of large volumes of acid mine water in the mined out openings. The resulting poor quality water, with high concentrations of cadmium, iron, lead and zinc, began discharging at the surface in 1979. Contamination of the underlying aquifer supplying local residents was first detected on a localized scale in 1980. The present surface water and ground water contamination have lead to the area being classified as one of the top ten hazardous waste sites in the U.S. by the EPA under the superfund program.

Jan 1, 1982

By J. Creamer

Pumping plays a major role across multiple process and facility applications in the mining world. Examples include: raw water supply, leach solutions, chemicals, dewatering, and mine drainage, and process water for metal recovery. Mining operations such as grinding, classifying, separating and concentrating minerals all have pumps at the heart of the operations Special purpose pumps such as dewatering, process water and slurry pumps are at the heart of many of these processes. Unfortunately the pumps themselves are often overlooked in terms of energy savings potential as they are often embedded into these sophisticated processes which are the ultimate operational focus.

Feb 23, 2014

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

The $2 billion Horizon Lateral includes over 30 miles of trenched and tunneled pipeline with diameters up to 120 inches.Related infrastructure includes large and small pumping stations, reservoirs, and flow control facilities. This paper will discuss the strategy and processes used to determine contract packaging and contracting delivery methods for the various project elements with an emphasis on the tunnels and trenchless crossings. Prior Authority experience and the rigorous risk-based approach to develop the preferred alignments played a large role in determining the outcomes along with schedule concerns and permitting and easement acquisition.

Jun 13, 2023

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By E. Pizarro

Division Andina has considered in its long range planning, the exploitation by panel caving method of "Third Panel" mine, which was started its production stage during the second half of 1995. This mine has two production levels, the first is grizzly level and another is L.H.D. level. Both sectors use the same haulage level where mineral is recollected through ore pass. For mineral loading and haulage its use 50ton diesel trucks combined with electro-hydraulic chutes. The automation has permitted what this operation is carrying out with remote control by driver's truck, in concordance to short range planning.

Jan 1, 1998

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

By M. Gunter, M. Buzon, B. McNamee

"A Google search on talc asbestos will yield over 500,000 hits – the reason being the growing number of civil lawsuits in this area. Historically the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos. Ultramafic hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc; they can occur in the surrounding black-wall, also the serpentinite host rock is in direct contact with the talc. Thus allegations can be made non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. INTRODUCTION Gunter (1994) wrote the following in regard to the question “What is asbestos? “The question yields different answers depending upon the audience. To a mineralogist, asbestos is a mineral form. To an engineer, it is an industrial material with several useful properties. To a medical doctor, it is an agent that might cause certain diseases. The third answer invokes several more issues: to a lawyer, a possible lawsuit; to a news reporter, a story; to an asbestos abatement worker, a job; and to a public school administrator or a parent, a nightmare.” The main function of that article was to try and provide background information to be taught at the college level to help students understand some of the issues associated with the use of asbestos in our modern society, and especially its use as a fireproofing agent in schools and public buildings. At that point in time one of the main issues was asbestos abatement as the mining and use of asbestos was waning as its health risks became more clearly known in the occupational setting. Now over 20 years later the current issue we are dealing with herein is “asbestos” occurring naturally in talc. This is a well know concern for those in the talc industry and they have been working on methods to ascertain if their products contained “asbestos” since last century. As such our articles will focus more on issues emerging from recent litigation, and the confusion that occurs, especially in the “asbestos” nomenclature as the mineralogist, engineers, doctors, and lawyers previously mentioned try to communicate. And lastly we need to remain cognizant of the fact that people are still dying of mesothelioma in the US. As a last resort to recoup expenses as they are dying they often respond to the TV advertisements we’ve all no doubt seen."

Jan 1, 2016

By Madeline Mello, Michael Low, Nick Karlin, Bryce Scofield

The LA Effluent Outfall Tunnel is the first tunnel in the United States to incorporate post- tensioning into the precast segmental lining. Several unique components were integrated to ensure that the post tensioning could be carried out successfully in the tunnel, even concurrently with the TBM excavation. This also required the development of new processes both in the casting facility and in the TBM to ensure that the almost 3,700 rings could be successfully manufactured, threaded, stressed, and grouted. This paper will discuss the material selection, fabrication, and installation of, as well as lessons learned from, this first in country tunnel lining.

Jun 23, 2024

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risk associated with the design of mine waste management facilities. These experiences show that the technical and managerial challenge of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur to this day in both developed and developing countries is indeed remarkable, and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailing storage facilities are, in many cases, more demanding than those of conventional water dams, because seepage of fluids which contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 1999

By V. M. Lepetic

Large tonnages of copper and molybdenum sulfide ore are treated by flotation. Substantial savings could be realized, particularly in high-capacity concentrators, by use of a simplified flotation technique involving lower reagent consumption. Chalcopyrite and molybdenite from some deposits can be floated by use of only a frother as a single flotation reagent; acceptable concentrate grade and recovery can be obtained. Separation of molybdenite from copper sulfides may become simpler and less costly. The genesis of the ore and the ions present in the flotation pulp liquid phase appear to be the major success-determining factors.

Jan 1, 1972

By R. Hendrickson

In the 1940's a top blown water-cooled oxygen lance was developed to inject oxygen into liquid iron. This process, the LD or BOF process technique, today is used in 65% of the world's steel production, and represents the largest oxygen market for temperature enhancement in steel and non-ferrous smelting applications. There are three major approaches to the use of oxygen in metallurgical processes: (1) general enrichment of the air supplied to burners or tuyeres, (2) under-flame enrichment or injection, and (3) the use of an auxiliary oxy-fuel burner as a heat source. With each of these techniques there are technical and economic trade-offs.

Jan 1, 1990

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

By Oren Tranbarger

The ability to sense or detect the coal/non-coal interface during mining can provide numerous advantages for improving net coal recovery and quality, for increasing productivity, and for mining coal which would otherwise be ignored. This is particularly true when considering multiple, pitching, and thin coal seams. This paper discusses the application of coal interface sensing and examines several potential coal interface sensing techniques with respect to state-of- the-art, design, performance, and cost criteria. Four interface boundaries are considered: the roof, the floor, the rib, and the forward region.

Jan 1, 1982

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022