Search Documents

By Bahne C. Cornilsen, X. Shan, David H. Carlson, John H. Johnson

The air in three U.S. underground coal mines has been sampled. The data developed show the relative importance of the various pollutants and quantify the need for control. Total respirable particulate matter (TRPM) was found to be the critical pollutant (the one requiring the most dilution for control). TRPM is considered to be "respirable coal dust" by procedures approved for sampling in U.S. underground coal mines. However, this "respirable coal dust" also includes diesel particulate matter (DPM) and particulate from other sources. While "respirable coal dust" was the critical pollutant, Raman spectroscopic analysis showed that more than half of this "respirable coal dust" was DPM. The DPM in the samples ranged from 22 to 152% of the 2 mg/m3 limit for respirable coal dust. Thus DPM was the critical pollutant using the 2 mg/m3 respirable coal dust limit. SO2 gas produced by the combustion of diesel fuel containing sulfur was the second-most critical pollutant. Characteristic curve slope (CCS) values were calculated to determine the quantitites of the various pollutants generated per unit of diesel haulage activity. Mine 1 had the highest TRPM CCS values with 29 mg/m3/%C02 for the Ramcar and 57 mg/m3/%C02 for the Haulageway location. The highest coal particulate CCS measured was 30 mg/m3/%CO2 and the highest diesel particulate CCS measured was 27 mg/m3/ %C02. Both of these high values were measured in the Mine 1 haulageway location. Calculations were made to determine the controlling CO2 concentrations (CCC) at which all other measured pollutants would be within their limits. These CCC values, which, for the mines sampled, were based on TRPM, varied from a low of about 0.07% for the Mine 1 haulageway location, to a high of about 0.15% for the Mine 2 Ramcar and haulageway locations. Weekly average CO2 concentrations measured in these mines ranged from 0.09 to 0.11 % for the Ramcar, from 0.05 to 0.09% for the haulageway, and from 0.08 to 0.11 % for the return. The concentrations of TRPM ranged from 1 and 2 mg/m3 in mine areas frequented by personnel, and to greater than 4 mg/m3 in returns where personnel are not exposed.

Jan 1, 1991

By Stefano Ceccotto, Eugenio Trussoni

"INTRODUCTION Contemporary city is made of layers. Physical structures layers (built fabric, residential, commercial industrial etc. ), infrastructural layers (below and above ground), “green” layers (parks and open spaces), and also informational layers, i.e. connections, links, between sectors of the city and other territories. The “city of layers” concept represents the exercise of “rebuilding the city” per each layer, highlighting those physical built structures that are functional to define a relation. For example, if consider the “connection” relation, the city is re-designed by considering only transportation built structures. The layer obtained in such fashion is hence the “transportation” layer, including below grade infrastructures (subways) and above grade lines (rail, bus, tramways etc.), as below shown in Figure 1.In this sense, the contemporary city is represented by separate constructs assembled together according to a specific functionality (e.g. “connection”). As a consequence, the relation between what is built underground, and the related above-ground development, can be perceived in his most evident appearance. What could happen within the contemporary city if the planning process would begin from below to above and not vice-versa?INTERACTION The question risen in the introduction is strategic when approaching the difficult task of designing (or re-designing) a multi-level organism like the contemporary city. Nowadays, the theme of integration between underground and at-grade master planning has become the subject of many urban renovation projects, where the design process has begun within the transportation layer, underground, and further developed by interacting with at-grade structures already existing or in phase of design.A series of case studies where below/above interaction plays a key role in the project will be further analyzed. Moreover, it is relevant to understand the mechanics of an urban transformation process that originates within the transportation layer and ends up with the design of entire sectors of the city. The Transit Oriented Development approach is a useful tool to clearly understand such transformation process. TOD has become, in particular in the last decade, one of the most effective tools for urban design, in order to solve simultaneously the many different instances related to transit planning, urban design and real estate market."

Jan 1, 2016

By J. W. Leonard

Gravity based coal/mineral preparation plants must be operated to yield products of a quality satisfactory to existing markets; but, because of historic control problems, recovery is frequently sacrificed to achieve quality resulting in losses of valuable product. Plant control has ranged from intuitive in-plant spot quality judgments made by various operators to gross methods involving such devices as density gauges, floats, grab-sample on-the-spot sink-float tests, etc. Millions of tons of quality coal/minerals are lost to refuse each year, because of the historic lack of a continuous and dependable control system. The result is both serious economic as well as environmental losses. While the economic losses are obvious, less obvious environmental losses, in the case of coal, result from the misplacement of more ignitable quality fuel to refuse banks. A control system capable of supplying a market-grade coal/mineral product, while continuously minimizing product losses to refuse, has until recently escaped technology.

Jan 1, 1991

By R. L. Lewis

The White Pine Mine is the second largest active underground copper mine in the United States, covering an area of approximately 34 km2 in the Upper Peninsula of Michigan. A numerical flow model of the White Pine Mine was constructed to evaluate engineering controls that would reduce the rate of mine water discharge after closure. Of the passive controls evaluated, the placement of low-flow bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35 percent.

Jan 1, 1996

By John D. Gardner

This paper describes a process which finds the maximum worth of a mineral deposit. The procedure requires two phases. The first uses a microcomputer evaluation model to find the optimum design input, with minimum attention giving to actual mining constraints that might exist. The second phase runs the first-phase design parameters through a direct simulation model on a mainframe computer. In phase one, financial, economic, and geotechnical data are entered; and an idealized list of design parameters is output. The list includes optimum values for cutoff grade, mine life, mine size, paytons, paygrade, and payvalue. In addition, the model generates pro forma operating and cash flow statements and it indicates the maximum net present value (NPV) possible for the deposit along with the probability of that oc¬curring. The initial results imply perfect mining conditions. In phase two, when actual mining selectivity, sequence, and other practical design considerations are related in a direct simulation model to the optimum criteria found above, the maximum NPV invariably decreases. However, if it is still satisfactory (NPV greater than or equal to zero) then the maximum worth/ optimum design have probably been found in the first iteration. If, on the other hand, NPV is now unsatisfactory, then design compromises must be made and simulated, and the results rerun through the evaluation model. If several iterations fail to yield a positive NPV then the deposit is most likely unfeasible t for the forecast economic conditions used in phase one.

Jan 1, 1986

By Hongjie Yu, Mike Mooney

Transitions between geological/geotechnical soil units have a critical impact on the operation and performance of a tunnel boring machine (TBM). Geostatistics-based probabilistic modeling is used to quantify the uncertainty in soil transition locations. This paper presents two unique soft-ground tunneling case studies where the results from the geostatistics-based probabilistic modeling are compared to the TBM data and as-encountered ground conditions derived from the actual TBM data. The assessment enhances the confidence in using geostatistics to improve ground awareness for efficient tunnel construction, minimizing different site condition (DSC) claims, and improving decision-making on tunnel projects.

Dec 1, 2022

Gold cyanide equilibrium adsorption isotherms in the loading range typical of operating carbon-in-pulp/carbon-in-leach plants have been established and the effect of various cations and the presence of copper cyanide species quantified. It was found that the equilibrium loading of gold was enhanced by the presence of sodium or calcium, with calcium having an order of magnitude stronger effect. The presence of copper has an adverse effect on the equilibrium loading of gold. A unified model was developed to predict the effect of sodium and calcium concentrations in solution and the competitive carbon adsorption of copper on the equilibrium loading of gold on carbon. A satisfactory agreement between the measured gold equilibrium loadings and the model results was obtained over a wide range of solution conditions.

Jan 1, 2010

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By B. K. Mishra

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills (14-18 ft). DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important factors such as the configuration of the liner and the geometry of the lifting surfaces are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill with particular emphasis to large diameter mills.

Jan 1, 1992

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By A. Vaillant

Classifiers that are used to separate granular materials into a coarse and a fine stream, are considered. Fundamental Equations are presented which apply to all, such Classifiers and all feed size distributions. The practical, real Classifier is compared quantitatively with the perfect. Classifier. A Formula is introduced for the Real Classifier Selectivity, that defines what portion of each particle size is sent to the coarse outlet duct. This selectivity function is characterized by three Parameters, one of which (b) is a numerical measure of the sharpness of classification. A new dimensionless variable (J) appears in Equations and Graphs for recirculating load, product size distribution and specific surface in the classified product. This variable combines the effects of sharpness of separation, Classifier setting and fineness of a Rosin-Rammler Type feed to the Classifier. Classifier efficiency is defined, based on Specific Surface.

Jan 1, 1967

By M. Jawed

Coking coal reserves in India are distributed geographically in Giridih, Raniganj, East Bokaro & Jharia Coalfields (J.C.F.). 97% of prime coking coal in JCF coming through underground mines is credited to Bord & Pillar mining systems inspite of the fact that it results in heavy mining losses. The cost of mining in B & P mines has been much higher due to various factors. In this paper, O.R. model has been discussed with case study for optimizing the cost of production in operational underground mines. Also, a computer algorithm has been discussed using a schematic flowchart, which provides the trend of mining-losses 'in different mining, systems with changing design parameters and finally selects, the optimum mining system for undeveloped seams based on economic appraisal criteria.

Jan 1, 1989

By J. B. Gwiazda

In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the .u factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the .u of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves.

Jan 1, 1987

By J. E. Gray

Before specifications are discussed it may be well to define the term "Mineral Aggregates." Professor K. B. Woods (1) defined "Mineral Aggregate--An aggregation of sand, gravel, crushed stone, slag, or other material of mineral composition used in combination with a binding medium to form bituminous and portland cement concrete, macadam, mastic, mortar, plaster, etc., or alone as in railroad ballast, filter beds, and various manufacturing processes, such as fluxing, etc. " This definition is too all inclusive for the purposes of this paper; therefore, this discussion will be confined to specifications for natural aggregates which means sand and gravel and crushed stone, and limited primarily to coarse aggregate which is aggregate larger than one-quarter inch in size. To the uninitiated, this may seem to be a very limited subject on an unimportant material. However, aggregates are essential in all types of construction. The tonnage and value of these two aggregates produced in the United States during 1959 as reported by the Bureau of Mines were as follows: Sand and Gravel 729,895,000 tons valued at $728,527,000 Crushed stone 581,721,000 tons valued at $824,411,000

Jan 1, 1961

By K. O. Johnson

Contaminant transport of mine and mill tailings is controlled by the hydrologic flow regime and the geochemical mobility of the contaminants. Contaminant' mobility is primarily determined by chemical reactions occurring within an interface zone between the tailings and soil The large geochemical differences between tailings and groundwater create a disequilibrium in the groundwater with respect to the soils when seepage from tailings enters the groundwater. Precipitation and dissolution reactions involving the major chemistry occur to return the perturbed system to chemical equilibrium between groundwater and minerals. Retardation of trace elements depends upon the chemical character of the groundwater and the adsorption substrates. In the case of uranium mill tailings, the mobility of contaminants is controlled primarily by precipitation/dissolution reactions which neutralize the pH, modify the Eh (redox potential), and produce highly adsorptive substrate for retardation of trace elements.

Jan 1, 1988

There are several simulators available and are being used for analysis, improvement and optimal control of the grinding process. However, these tend to be developed on informal software engineering methodologies. The informal approach is not suitable for long term development and a formal design methodology is necessary to develop efficient, error-free, and easy-to-use and to maintain software. In meeting this goal, basic concepts of a software model for describing the mineral process objects has been proposed. The software model forms the basis for software design and efficient implementation of the simulation. This paper describes the development of software models for grinding circuits. The work constitutes the theoretical foundation for the development of an advanced simulator for comminution.

Jan 1, 1995

By P. C. Thakur

Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1952 at the Humphrey Mine of Consolidation Coal Company for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for eight years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300-to 600 m, with reasonably precise directional control and within practical cost limits.(1) Mining Research Division of Continental Oil Company, the parent company of Consolidation Coal Company, began a research program in the early 1970's to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary Its of this research have already been published.(2) To date nearly 4500 m of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: 1) The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3 percent in course of two to three months from original values of nearly 0.95 percent.

Jan 1, 1979

By C. C. Hatch

As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer and winter of 1975 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses and to permit study of alternative circuit configurations if desired. This paper describes the simulation methodology employed and presents the results of a computer study of the secondary crushing plant (1).

Jan 1, 1979

By Hassan El-Shall, El-Sayed A. Abdel Aal

The major goal of this study is to decrease iron content in wet-process phosphoric acid. Reducing the amount of post-precipitated sludge in the acid is another important objective in this investigation. In order to achieve these goals, research efforts have focused on bench scale testing of an iron-chelating reagent to remove iron from phosphoric acid produced from South Florida high-iron and -magnesium phosphate concentrate, and plant testing using freshly produced concentrated acids for reducing the post- precipitated sludge. The data obtained in the above studies suggest that the addition point of the precipitating reagent is very important, as the precipitated iron compound has higher solubility at higher P2O5 concentrations. Up to 60% Fe2O3 removal efficiency is achieved depending on the amount of the reagent, concentration of acid used, and operating conditions. The addition of precipitating reagents to freshly concentrated phosphoric acid leads to a decrease of up to 84% in sludge volume percentage depending on acid type and clarification conditions. Decreasing the volume percentage of the sludge facilitates acid handling as well as decreases the adherent water- soluble P205 leading to lower total P2O losses.

Jan 1, 2002

By W. M. Snoddy

The Montana Tunnels diatreme is a low-grade polymetallic ore body containing economically mineable quantities of gold, silver, lead, and zinc. Widely varying gold grades combined with the general erratic nature of the mineralization create a complex sampling, assaying, and ore control problem. In order to maximize productivity and profitability, a variety of procedures have been used. These include differing sample size, frequency and method. In addition, assay techniques have been adjusted and refined to fit specific requirements, the result of which is an accurate, functional sampling and ore control system.

Jan 1, 1991