Search Documents

By E. Poeck, R. Garvey, U. Ozbay, K. Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the mine-scale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures which most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps. INTRODUCTION The analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but for deep cover and squat pillar geometries, less accuracy has been achieved in predicting pillar performance (Mark 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs. This paper presents a study of pillar stability through the back analysis of the Crandall Canyon Mine collapse, which occurred in August of 2007. Pillar-scale models are utilized for the calibration of material properties and assessment of potential instability under varying conditions, and mine-scale models are constructed in an attempt to reproduce widespread failure and correlate with observations at the mine. Special consideration is given to the properties of the coal and the coal/rock interface, and kinetic energy is calculated throughout the course of the simulations to gauge the level of instability when pillar failure occurs. Models were constructed using the Universal Distinct Element Code (UDEC) (Itasca, 2014)."

Jan 1, 2016

By K. N. Mayfield, T. Novak

"The applications for automation continue to expand within the mining industry. These applications can range from the startup, control, and shutdown of processing plants to the autonomous operation of surface haulage trucks. However, the term “automation” should not necessarily be interpreted as the total elimination of human interventions since numerous mining processes can be partially automated. The future survivability of many mining operations will be influenced by a company’s willingness and ability to understand, accept, and utilize this technology. The mining workforce, including management and engineering, should be familiar with the technological capabilities and limitations for effectively implementing automation into mines for improving safety and productivity. The Department of Mining Engineering at the University of Kentucky has recognized this educational gap and developed an automation laboratory, along with project-oriented courses at the undergraduate and graduate levels. The laboratory and the course objectives are described in this paper, as well as the skills and abilities that students obtain at the completion of the course(s). BACKGROUND The touted benefits of automation include: improved productivity, lower operating costs, reduced drudgery of repetitive operations performed by workers, and the removal of workers from hazardous locations. The acceptance of advanced technology by the mining industry, however, has traditionally been slow. This cautious approach is understandable considering the complex and harsh conditions routinely encountered in mining operations. Bad experiences with some premature installations of newly hyped technologies may have also resulted in lingering skepticism by many mine operators. Nonetheless, with thoroughly demonstrated reliability and proven applications, automation based on programmable logic controllers (PLCs) has made significant inroads into the mining industry. Programmable logic controllers (PLCs) are the workhorses of automation. They were originally conceived in the late 1960s, long before the invention of the personal computer (PC). Initial PLC applications were directed towards sequential relay control in manufacturing plants, which subsequently eliminated the use of “relay logic” that was based on hard-wired electromechanical relays. With continuous advancements in electronics and computer technology over the years, PLCs have evolved into sophisticated and powerful devices with very stable operating systems. They are designed for deterministic logic execution with extreme consistency in timing, along with a high tolerance to temperature, humidity, and vibration (Smith 2003). Because of their robust characteristics, PLC networks now provide the backbone for most industrial automation applications."

Jan 1, 2017

By L. G. Austin

Introduction My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rap- idly developing knowledge of how stressed, brittle solids fractured, based on the Griffith crack theory. On the other hand, reading in the grinding literature gave me: • Kick's Law, which was clearly not correct in the light of modern fracture theory; • Rittinger's Law, which was also clearly not correct; • Bond's Third Law of Comminution, which was claimed to have something to do with the Griffith crack theory, but where the connection between the two was made by intuitive pseudo- scientific reasoning I could not accept; • the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. incorrect statements abound in the literature, such as “the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1 948) and Broadbent and Callcott (1 956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1 953) in Germany. We confirmed experimentally the validity of the equations for describing batch grinding (1 962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, (Fig. 1) (Berenbaum and Brodie, 1959). Irwin (1949) showed from solution of the stress-strain solutions that a small hole in a region of tensile stress reduces stress concentration at the hole, that is, the tensile stress at the tip of a crack or flaw in a solid is much higher than the general tensile stress in the region. The longer the crack, the higher the stress concentration. Griffith (1920) hypothesized that when the regional tensile stress is large enough, then the chemical bonds at a preexisting crack tip are stretched to breaking point, as illustrated in Fig. 2. When the bonds break, the crack becomes longer, the tensile stress concentration increases, the situation is unstable and a crack opens up (propagates) a surface of tensile stress, creating its own tensile stress at the leading edge. Stored strain energy is converted to the kinetic energy of the moving stress field, which is analogous to sound propagation through the solid, so the crack tip accelerates to velocities approaching those of sound. The moving crack will pass through regions that were previously under regional compressive stress. The equations for "ideal" and "Griffith" strengths are where a is the intermolecular distance, y is Young's modulus, g is the energy

Jan 1, 1998

By M. Tapper

If one considers that prehistoric man's first house may have been a limestone cave, calcium carbonate may be the most timeless of all building materials. Fanciful history aside, CaCO3 has been used for countless applications in human habitats. After all, tine marble block and tiles have always been the hallmark of eloquents and style. Mortars and cements derived from limestone have held together the very blocks of our civilization. In modem times, synthetic polymers are blended with ground limestone to produce everything from pipe, floor tile, cultured marble and house siding. All of these miracles of our technology contain CacO3 of various sizes and in varying amounts. This paper will discuss some of the critical attributes of CaCO3 which make it suitable for the new building products that have helped increase our standard of living. The vehicle of discussion will be a residential, single family house.

Jan 1, 1993

By P. K. Davis

The results of a previous basic study of the flow and design characteristics of the hydrocyclone has shown that a recovery as high as 99% with a product rating of 0.95 can be achieved on a "batch?2 basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-cyclone system was also sponsored by the U.S. Department of Energy. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1989

By Stephen Njoloma, Ivan Hee, Ravi Jain, Mina Shinouda

"INTRODUCTION DC Water’s First Street Tunnel (FST) is comprised of a collaborative effort between DC Water, DC Water’s Project Consultants Organization (PCO) led by Greeley & Hansen and McMillen Jacobs Associates and the design-build team of Skanska, Jay Dee, and Parsons Brinckerhoff. The fast-track project includes elements that were designed by the PCO and released for construction by DC Water prior to Notice to Proceed (NTP) and elements designed by the Design-Builder from 30% to released for construction after NTP. This required effective communication and technical coordination for integrated engineering and efficient construction. The project, constructed in an urban residential neighborhood, included innovative construction methods such as multiple location ground freezing, utilizing a centralized freeze plant, to minimize community impact. The means and methods chosen for cast-in-place shaft linings, precast segmental tunnel lining, microtunneling, sequential excavation method (SEM) adits and near surface elements reflected the immediate and sensitive surroundings, which varied by construction staging area (CSA). Technical aspects of the project, relative to the evolution from pre-bid to construction documents, are discussed along with modified designs to suit means and methods. SCOPE OF WORK In 2012, four major storm events swept through the District of Columbia and hit the Northeast Boundary sewer shed particularly hard with the neighborhood experiencing severe flooding. The extreme nature of the flooding, the damage to private property, and the health risks associated with exposure to sewage led to a multi-agency response and community calls for answers and action. The Mayor assembled a Task Force to evaluate a range of potential actions to address combined sewer flooding including engineering, regulatory, code revision, and management improvements. The Northeast Boundary Neighborhood Protection Project was the outcome of the Mayor’s Task Force; it is a three-step infrastructure initiative designed to offload the undersized sections of the existing collection system that serves the Northeast Boundary drainage area by implementing the McMillan Stormwater Storage Project, First Street Tunnel Project and the future Northeast Boundary Tunnel Project. Until the Northeast Boundary Tunnel Project is completed, the First Street Tunnel Project will add 8 million gallons of combined temporary sewer storage in a new tunnel under First Street NW to relieve undersized sewers that traverse the Bloomingdale neighborhood."

Jan 1, 2016

By Francesco Chiappalone, Daniele Nebbia, Lance Waddell, Greg Colzani

As part of the 3RPORT Project, a 5-mile tunnel is being excavated underneath the three rivers of Fort Wayne using a 19-foot diameter Slurry Tunnel Boring Machine. The groundwater pressure at the tunnel axis ranges from 4.5 to 5.3 bar. The rock mass hydraulic conductivity is very high with water inflows up to 10,000gpm imposing significant challenges to the project. After excavating 1,550-feet of the TBM tunnel, major leaks between the tailskin and the segmental lining were observed, indicating the potential deterioration of the tailskin brushes and the need for inspection and eventual replacement. The first part of the paper describes the planning of the intervention, including the design of the polyurethane grouting campaign, the procedures developed for the execution and the controls established during construction to timely assess the presence of potential hazards. The second part of the paper focuses on the experience gained during execution and lesson learned to prevent future occurrences of this nature.

Jun 13, 2021

By Dean Treweek, Anthony Harding

"Creating stable, safe, constructible and cost effective support to openings in segmental linings is often an important component of successful delivery of a tunnel project. The many constraints on successful implementation include operational, spatial, geotechnical, structural, and constructability. Failure to address these adequately can lead to significant impacts on cost, schedule, and safety. With reference to past project experiences, this paper provides a guide to the most commonly deployed solutions and their pros and cons to help designers quickly identify the most appropriate solutions for a particular project, or act as a starting point for developing new and/or project specific solutions. It highlights the challenges that designers and contractors must address together for successful support of tunnel openings, and the constraints that arise. It then describes the common structural forms of support, and how each form can mitigate the constraints, allowing an effective opening support system to be implemented. INTRODUCTION While only a small portion of the total excavated volume of a typical tunnel, cross passages are often one of the most complex elements of a bored tunnel to construct. Cross passages in soft ground typically involve ground improvement, groundwater control, and multiple temporary support measures to ensure safe construction in ground that has been overstressed due to the construction of the running tunnels. Permanent lining construction requires careful detailing of waterproofing and reinforcement to support both long term ground and water loads and support the broken out rings of the main lining. While there is not a great deal of literature specific to cross passage construction, the main issues are discussed in some detail by Lawrence and Taylor (2011). However, the temporary support of the running tunnel segmental linings during cross passage construction is not always given the attention it deserves. The authors have been unable to find much literature on the design of such systems, much less the considerations that have led to a particular solution. Lawrence and Taylor only mention two potential methods of support. It may be easy to dismiss the opening support as an inconsequential item, but selection of the wrong support type can have significant impacts on both cost and schedule."

Jan 1, 2016

By W. R. Hail

A proactive design and construct approach was used to remediate the Warm Springs Ponds Complex near Anaconda, Montana under "Superfund". The pond complex is used for treatment/settlement of heavy metals and is a repository for 19,000,000 cubic yards of tailings, precipitates and associated sediments. Remediation has resulted in treatment/settling capacity for flows up to the 100-year flood (3,300 cfs); expansion from 5 to 11 ponds in series requiring 12.5 miles of new or improved embankments with associated hydraulic structures; flood protection for the 0.5 Probable Maximum -Flood (PMF) (70,000 cfs); and closure of exposed tailings along with aquatic and terrestrial habitat enhancement.

Jan 1, 1995

By Patrick Shea

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management, U.S. Forest Service and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the National Park Service, U.S. Forest Service and Bureau of Land Management. The U.S. Department of the Interior has worked with the U.S. Geological Survey, the U.S. Forest Service, the U.S. Environmental Protection Agency, and western state governments to identify and prioritize these sites on Bureau of Land Management, National Park Service and U.S. Forest Service administered lands. This presentation will discuss the accomplishments we have made to date to clean up inactive and abandoned mine sites, focusing primarily on lands administered by the Bureau of Land Management.

Jan 1, 2000

By S. J. Cohen

Changes in our energy, national security, and commerce needs have necessitated identification of new sources of minerals, such as rare earths, lithium, copper, silver, aluminum, titanium, and the minerals on the U.S. Geological Survey’s (USGS) list of critical minerals (USGS, 2022). With the need to domestically produce these minerals, more mining will be required within the U.S. Some of these critical minerals deposit with naturally occurring radioactive materials (NORM), therefore, mining these minerals may concentrate NORM to the point that some states may require licensing and radiation protection programs. NORM is not regulated by the Federal government; it is regulated by the individual states. Consequently, overall national state of NORM regulation is chaotic with each individual state either choosing to regulate or not regulate NORM, and, if a state chooses to regulate NORM, then that state develops its own unique regulations. Further complicating the regulatory environment, states utilize a wide variety of strategies for regulating NORM, which sometimes results in inappropriate regulations, inconsistencies with specific radionuclides that are regulated, and inconsistencies with specific NORM types that are regulated. This paper will review the nature of NORM regulations, identify regulatory traps, and provide general guidance for identifying NORM and potentially avoiding regulatory jeopardy. Because of the chaotic nature of NORM regulations nationally, seeking guidance from qualified professionals with relevant expertise is recommended. Also, contacting the appropriate regulatory agency to gain a complete understanding of the NORM regulatory environment is useful for maintaining compliance.

Feb 1, 2023

By David M. Kjos

Large diameter autogenous and semi-autogenous grinding mills represent the primary thrust of the expanding grinding technology. In spite of initial difficulties, large autogenous and semi-autogenous mills have reached an acceptable level of technology which provides the mineral engineer with a reliable, low cost means of ore comminution. A successful milling installation begins during the design stage of the grinding mill and the plant it is to be installed in. This is particularly true in autogenous and semi-autogenous mills. Critical mill and plant design factors should be considered while the mill and installation are still only ?paper.? Various current liner designs will be discussed ranging from lifter bar/plate to integral types. Modes of operation such as "high-low" will be considered. Liner maintenance procedures ranging from laydown area in plant design, proper mill shutdown methods, to installation and bolt tightening complete the equation to yield optimum performance possible for any particular grinding application. The objective of this paper is to discuss trends in wear materials, designs and operating practices, and provide some guidelines for good practice as we move through the 1980's. We will put together concepts that relate to the designs, materials and applications so that higher performance can be obtained by the operator for his specific application. The concepts are shown as being in series because they are dependent on each other to achieve the desired performance.

Jan 1, 1985

By D. A. Poulter

The stability of a liner system is influenced by many factors which can be compiled into four basic groups. They are: 1. the liner system components and physical characteristics; 2. the geometry and slope of the liner system; 3. the loading conditions on the liner system; and 4. the foundation conditions under the liner system. Failures in the liner system that are due to one or more factors from the first three groups usually result in movement relative to the plans of the liner system. Failures associated with factors in the fourth group result in deformation(s) across the liner system section beyond its design limits. For purposes of these discussions a failure in the liner system refers to displacements or movements resulting in physical damage to the liner system such that it can no longer function.

Jan 1, 1995

By J. D. Miller, P. L. Sibrell

The nature of surface sites for the adsorption of gold from alkaline cyanide solutions has been investigated using samples of synthetic, highly-oriented pyrolytic graphite (HOPG). This HOPG material offers an idealized graphite structure enabling the independent study of the graphitic basal-plane sites and the edges, or defect sites, of the graphitic planes. Radiochemical and X-ray photoelectron spectroscopic experiments independently demonstrated that gold adsorption was much higher on the edges (defects) of the graphite planes than on the planes themselves. These results suggest that site-specific adsorption is prevalent in the adsorption of gold by graphitic carbons (including activated carbon, carbon black and graphite) and that most of the favored sites are at edge defects in the graphite crystal structure.

Jan 1, 1993

By Gy. Deák Deák

The ECOMINING platform aims to develop a scientific and technical organization in order to promote within the natural resources industry a framework for environment-friendly exploitation technologies (on Best Available Technologies principle) and also to develop a solid basis for performing Research and Development projects. The ground of this project is the success of the First International Seminar: ECOMIN-ING - Europe in 21st Century1, organized by the Research and Development National Institute for Metals and Radioactive Resources Bucharest in co-operation with ITASCA Consultants GmbH Germany, the University of Petrosani and supported by the National Society of Salt Bucharest & Praid salt mine branch and the Ministry of Economy and Commerce. The platform provides a complex data base, for partners? selection and researchers? team structure. This can provide the scientific results with a high level of confidence for the projects of interest in the field of exploitation of mineral resources and for the participation on national and international project proposals competitions (i.e., target the 7th Framework Programme or any European / national programme, which can provide funds for the ECOMINING platform field of interest). The next step is the affiliation of the ECOMINING platform to the European ones, and to be compatible with them. The ECOMINING platform represents itself a 7th Framework Programme (FP) project idea.

Jan 1, 2007

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010

By H. L. Monroe

Meramec Mining Company, owned 50% by St. Joseph Lead Company and 50% by Bethlehem Steel Corporation,- is engaged in the mining, concentrating and pelletizing of iron ore from the Pea Ridge Mine which is located in the rugged, wooded Missouri Ozarks about 15 miles from the town of Sullivan or 75 miles southwest of St. Louis. The orebody was delineated in the middle 1950's by the St. Joseph Lead Company during the Company's intensive exploration program to discover new lead orebodies to replace the declining reserves of the famous Southeast Missouri Lead Belt. An airborne magnetometer survey was run by the U.S. Geological Survey, the Missouri Survey and several mining companies, (of which St. Joseph Lead Company was the principal supporter). The survey was published in 1950 and disclosed an anomaly in the vicinity of Pea Ridge. In 1950 test drill holes disclosed that under some 1300 feet of sediments there did exist an iron deposit of probable commercial significance. No further action was taken until 1956 when additional drill holes confirmed beyond reasonable-doubt-that this was a major iron ore discovery.

Jan 1, 1965

By R. S. Hearon

The image of the open-pit miner in the eyes or the Environmentalist has never been very outstanding. The phosphate industry, whose history in Florida reaches back to the late 1800's, can-not be credited until recently with a large number or accomplishments in terms of protection or the environment to change this image. This lack of action was not deliberate or in opposition with the desires of the public. In the formative years, there was little or no public and the companies found it necessary to build towns to house their employees and their families, towns which remained in existence until the late 50's and early 60's or formed the core of present large communities. Neither these pioneers nor most subsequent resource developers considered themselves un-thinking spoilers, nor were they so regarded by their contemporaries. Instead, they acted in a manner consistent with their environmental circumstances and intellectual heritage. Early Americans did make mistakes in using the land but the mistakes became apparent only in the opinion of later generations. Over the past five to ten years, there has been a new self-awareness in the industry with regard to environmental responsibilities brought about, in part by a continuing onslaught of new regulations with jurisdiction over our activities. Part of the new regulations are aimed at industries as a whole while many, particularly state regulations, pertain specifically to the phosphate mining industry. Why all the new regulations? The reasons are encased in a complex web of activity but stem primarily from a new public awareness of its environment. More and more of our youth have become interested in the environmental science areas such as biology and ecology. The tremendous growth rate in both the population and industry has made personal issues out of subjects such as atmospheric inversions and water shortages which previously were abstract concepts. The State has grown from a population of 1,500,000 in 1930 to approximately 9,000,000 people today. This personal impact and general lack of knowledge on the part of the public concerning economics has resulted in big business no longer being held in awe, often in contempt and generally in suspicion where environmental concerns are encountered.

Jan 1, 1978

By G. J. Joy, J. P. Rider

"Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 100 ft./min. This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the National Institute for Occupational Safety and Health [NIOSH] is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research [OMSHR] Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities (500, 700, and 900 fpm) and at water pressures of 100, 150, and 200 psi. Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer a spray manifold was fabricated and evaluated at an underground operation. INTRODUCTION In 2012, underground coal mining in the United States produced a total of 342 million short tons, with longwall mining accounting for over 53% of this production [EIA 2013]. The longwall mining industry continues to see remarkable and significant improvements in longwall mining equipment and mining practices. Average shift production during compliance dust sampling has increased from 3,500 tons per shift in 1994 to approximately 6,000 tons per shift in 2012. A dramatic decrease in working longwall faces from 80 to 49 has occurred over the same period [Fiscor 2013]. Factors specific to longwall mines that supported productivity improvement include: higher capacity shearers, improved shield hydraulics and control, higher horsepower for equipment, wider face conveyors, and larger faces. Today, the average face width has increased to 1,188 ft., with one longwall operation reporting a face width of 1,650 ft. compared to an average of 750 ft. in 1994 [Fiscor 2009, 2014]. Panel lengths in 2013 averaged 11,307 ft. compared to 7,000 ft. in 1994. Overall production from U.S. longwalls has increased by nearly four percent from 2007 to 2012 with over 182 million tons mined annually [EIA 2013]. Given the volume and rate of coal produced on longwall faces, the potential to generate large quantities of respirable coal mine dust also exists."

Jan 1, 2015

By M. B. Mooiman

Cyanidation of gold and silver ores by conventional mining and milling techniques has been practiced for over a century. During the past decade, heap leaching has emerged as a viable process for treating certain gold and silver ores. (1) The rapid development of heap leaching for gold and silver ores is largely a result of lower capital and operating costs and faster start-up time than that offered by conventional mining and milling. In general, these features make heap leaching an ideal approach for exploiting either small or large low-grade disseminated deposits of gold and silver considered to be uneconomic by conventional methods. The development of heap leaching technology has evolved from the operations initiated in the western United States. The basic components of a typical heap leaching operation are depicted in Figure 1. Run-of-mine or crushed ore (usually 1 to 5 ppm gold) is delivered to specifically prepared impervious pads. Alkaline cyanide solution is applied to the surface of the heap and allowed to percolate through the heap (typically 10-30 ft high). Pregnant leach solution which drains from the heap is collected and stored in tanks of sufficient size or in collection reservoirs. Gold and silver are recovered from the pregnant solution and the barren solution is recirculated back to the heaps after reagent make-up.

Jan 1, 1983