Search Documents

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

Despite two large projects represented in the keynote docket, the mood of the 2011 SME Arizona Conference was summed up best by Ferol Baker, general manager of New Mexico Copper Corp. (a wholly owned subsidiary of Themac Resources Group), ?In the past, it seemed like you couldn?t go to a conference like this without hearing about one big new greenfield project after another. Now what you see is companies doing internal expansion or small-scale brownfield development.? Overall, the tone of this year?s meeting, held at the J.W. Marriott Resort at Starr Pass in Tucson, AZ, was upbeat, yet practical. From the keynote and luncheon addresses to the six panels of sessions, the projects described were positive about the future, yet focused on the details required to make those projects come to fruition.

Jan 1, 2012

By J. Kallioinen

Flotation of low grade Ni ores with serpentinite host rock tend to yield low recoveries of Ni With high MgO contents in the concentrate. The recovery can be enhanced by optimizing the sub-processes in the pulp and in the froth. The new OF-100 flotation cell has been designed to be adaptable to different feed fineness (Coarse, Fine). The losses can according the research conducted at Outokumpu's Hitura plant be substantially decreased by OF-100's new rotor and stator design and froth zone geometry. The froth residence time is used to adapt for feed particle size changes measured by the Outokumpu PSI- 200. Models for the behaviour of different particle Sizes in the sub-processes have been developed. The modified froth zone geometry and the capability of maintaining a froth of desired thickness allows efficient washing of the obtained concentrate producing low levels of MgO.

Jan 1, 1994

By Richard E. Ellwanger

Methods of utilizing flocculants as settling and filter aids for mineral processing slurries are reviewed. Broad chemical classifications and techniques for proper dilution, multiple addition, and combination treatments are discussed. A variety of custom built and commercially available systems for make up and delivery of flocculants to the application points are in use through- out the mining industry. Those concepts which, in the author's opinion, are particularly important to the successful make up and use of flocculants are presented in relationship to the available make up and feed systems. Actual industrial applications are included in the presentation.

Jan 1, 1980

By V. Prabhu, D. Mantha, R. Reddy

Secondary copper blast furnace slag was treated with carbon to derive the conditions for maximum recovery of copper with a minimum simultaneous reduction of iron oxide. Experiments were carried out to study the effect of temperature, carbon and CaO additions to the slag on the efficient recovery of copper. A two-stage reduction process was also employed to study the efficiency of copper recovery and the results were compared with those of single-stage reduction. The maximum recovery of copper in alloy phase was obtained with 5 % initial carbon in the slag, 2% CaO addition to the slag and at a reducing temperature of 1573 K. Higher grade of the alloy phase with respect to copper was obtained by employing a two-stage reduction process. The results obtained in this study are comparable to those of the earlier research on the recovery of copper from reverberatory furnace discard slags.

Jan 1, 2004

By J. Wesley Atkins

In considering the importance of lease management and administration, I have decided to approach the topic, Lease Default and Eviction: Action or Reaction, as a three phase presentation dealing with mineral lease administration and management, past, present and future. Though the title may border on the dramatic, it illustrates the real consequences of alternative approaches to property management viewed from my experience in the evaluation, development and implementation of a number of such systems and services in my current position as president of Talco Group Corporation. First, though, let's take a moment and set the stage by giving a few actual examples of why a pragmatic approach is needed in this particular area.

Jan 1, 1983

By S. Healey, P. Jean, G. Deschenes, M. Fulton

Three years ago, the New Britannia Mine started a project to improve productivity of its cyanidation plant. Results indicated that gold dissolution was strongly influenced by sulphide minerals and that the slower gold dissolution rate had a detrimental effect on overall gold recovery. The leaching strategy had to be modified to address this issue. Changes to the leaching circuit proved to be very successful. The first action was to introduce lead nitrate in the leaching circuit. The strategy of addition of lead nitrate was upgraded in three steps. An on-line free cyanide analyser was installed and the strategy of cyanide addition automated. The enhancement of the leaching kinetics have resulted: an 4% increase of gold recovery, from 87.8% in 1996 to 91.9% in 1999, which represents a reduction of 0.17 git Au in the leach residue; an average of 1330 additional extracted gold ounces per year from 1997 to 1999; a 21 % reduction in the cyanide consumption; the shut down of the cyanide destruction plant; and finally a contribution to the 27% reduction in the overall production cost per tonne of ore.($ 3 per ton). The significant increase of the throughput was instrumental in the reduction of the processing cost. In 1999, the improvement of gold recovery represented an additional gross revenue of $c""l.9 Million. The project is discussed in details in this paper.

Jan 1, 2000

By J. W. Mustard

The Macmillan Pass tungsten property (MacTung) is the largest known copper-tungsten, calcic, exoskarn deposit in the Western Hemisphere. Located on the border between the Yukon and Northwest Territories in northwestern Canada, the deposit crops out on Mt. Allen within the Selwyn Mountain Range. It was discovered in 1962 by a subsidiary of AMAX Inc. and has since been explored by 16,300 meters of surface and underground diamond drilling and by 800 meters of underground development. Geologic reserves are in excess of 30 million tons, grading slightly less than 1.0% WO3. Scheelite (CaWO3 ) is the main mineral of economic interest. Accessible by road, the property is not in production. Previously estimated reserves at MacTung have been unable to fully utilize all the geological controls on mineralization. In the past three years, however, an intensive program has been underway to improve our understanding of the deposit and to use the resulting information in a more precise way. This paper will discuss the key aspects of the geology as they specifically relate to reserve estimation and will demonstrate how these controls are being used in a geostatistical model of the deposit.

Jan 1, 1985

By Gilmore R. Tostengard

The advent of inexpensive computers has opened vast opportunities for improved planning and control of capital projects. The mining and mineral processing industries have welcomed the opportunity, and new and improved quantitative management techniques have abounded. This chapter will discuss commonly used computer applications for economic justification of the project, preparation of the cost estimate, planning the work schedule, monitoring work progress, and control of costs and productivity. Finally, there is a review of the degree to which the industry uses these applications. Our experience suggests that while we in the industry have been quick to adopt the new techniques, the quality of our input data has not always kept pace. During the next decade, our push should be toward improving the quality of the basic data and assumptions so that we can fully benefit from the sophisticated techniques. The GIGO (garbage in, garbage out) principle is a wellworn cliche, but it is especially valid here. One of the keys to getting good input is commitment. Unless the managers who are to use or benefit from the system are committed to it, the effort will fail. They must be com- mitted to the underlying principles of planning and control sufficiently to expend their time and resources on them; planning should be especially given emphasis. They can't be too busy to plan.

Jan 1, 1979

By C. Haycocks

The Appalachian coal fields contain many mineable contiguously placed coal seams. Selection of the mining sequence for these seams, historically and currently, is based primarily on considerations of seam ownership, availability and economics. Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to recovery costs and safety of mining in the subsequent seams. The purpose of this paper is to examine the conditions that can develop in an underlying seam due to stress concentrations that can occur below pillars or abutment zones in an overlying seam, and suggest guidelines for avoiding them. This situation most commonly occurs when the overlying seam is mined first, although simultaneous and subsequent mining of the upper seam can also produce such effects. Other interaction phenomena resulting from subsidence or arching will not be considered here. The methodology used in this research utilized both computer and body loaded photoelastic models to study the interaction mechanisms. Field studies are used in both interpretation and analysis of the results. Numerous examples of load transfer from upper workings exist in all parts of the world and many of these have been incorporated into this work. Such interaction problems are quite common and likely to be an ever increasing occurrence as mining activities in old seams are completed and new seams opened up.

Jan 1, 1982

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By A. S. Speirs

Over the last few years, the never-ending search for mineral wealth has taken the exploration efforts of Canadian mining companies further and further into the High Arctic and isolated locations where regularly scheduled transportation and communication facilities are nonexistent. Names such as Black Angel, Nanisivik, Asbestos Hill, New Quebec Raglan, Rabbit Lake, and Arvik are today frequently mentioned in mining publications. Twenty years ago, mining in these locations was unheard of, mainly due to logistic problems. However, improvements in the design and use of helicopters, STOL aircraft, and icebreakers in northern areas have helped to overcome these problems, making these locations more attractive to mining companies. Since 1969, when Redpath completed its first Arctic project at Texas Gulf's Scrathcona Sound property on the northern tip of Baffin Island, Redpath has been actively involved in contracting and engineering projects in three general areas: the High Arctic, Ungava and Greenland. A map showing some of these projects is shown in Figure 1. In these areas, permafrost conditions exist from a depth of 274 metres in Ungava to a depth of approximately 610 metres in the Little Cornwallis Island area, with rock temperatures ranging from -5°C to -13°C. Outside temperatures range from a low of -50°C in the winter to a high of 21°C in the summer. High winds in the winter result in wind chill factors lower than -73°C

Jan 1, 1980

By Rollin A. Slater

The bulk materials handling industry has served silently for years as the skeleton structure and often the central system of nerves and nourishment for the body of basic production industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has been prominent in this phenomena and plants of the sixties are as unlike the second war vintage as our current crop of basketball players differ from their fathers. Steel has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. The supporting industry of materials handling has likewise improved its techniques and currently has a new stronger generation of equipment to perform its necessary supporting function. It has been my fortunate experience to have been instrumental in the creative stages of several new steel mills which are currently in conceptual design or actual construction. Drawing upon exerpts from this experience, this paper will describe a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details of past work are not available for publication, therefore, the plant described herein is a composite of ideas and will be the new plant of the Hypothetical Steel Corporation which will be located on the lower shores of the Great Lakes.

Jan 1, 1967

By F. P. Schwarz

Even in an otherwise care-fully done sampling procedure, reducing subsample weight, or splitting, when the grain size of material is too large commonly generates significant error. Such error can be estimated from the standard deviation of differences between values of PAIRED ASSAYS. Samples from split-ting steps immediately before comminution, and showing a restricted range of grade, generate paired assays. Splitting steps characterized by relative standard deviations exceeding 16% generate nonrepresentative data. Such steps should be redesigned to optimize reliability of assay-dependent studies. A sampling scheme can be graphically characterized, and then redesigned as appropriate, using a SAMPLING NOMOGRAPH. Use of the nomograph avoids continued replication of assays. Generally at a splitting step, excessive error can be reduced by comminuting more material. Unnecessary effort can be mitigated by comminuting less finely and/or by splitting to a smaller weight.

Jan 1, 1992

By Jay P. Chapman

The basic control requirement for multi-pump, long distance slurry pipelines are discussed and a particular example of an operating slurry pipeline using programmable controllers is presented.

Jan 1, 1983

By P. Rusin

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environ-mentally unacceptable. Bio-reductive leaching of such ore samples at MBX resulted in high recoveries of silver and molybdenum. When baseline 3-day cyanide bottle roll tests were conducted on manganiferous oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bio-reduction with 99.8% dissolution of manganese. A follow-up cyanide bottle roll test yielded an additional 8.5% silver recovery for a total recovery of 94.5%. Baseline 3-day acid bottle roll tests of the iron oxide molybdenum ore yielded 1.8% moly. However, bio-reduction solubilized 93.3% of the moly into the growth medium. An additional 0.3% moly was recovered during the follow-up acid bottle roll test. Microbial treatment of refractory oxide ores with bio-reductive bacteria resulted in higher recoveries of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and moly was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1992

By George C. Trevorrow

It is a pleasure to appear on this program and discuss a subject which is of particular interest to me. In my regular duties as Safety Director of Bituminous Coal Operators' Association, I am called on by member companies to discuss matters affecting face ventilation. As a member of the Joint Industry Safety Committee, as I will later describe, I have a part in processing requests for the use of auxiliary fans for face ventilation. The use of auxiliary fans in bituminous coal mines for this purpose came into rather wide use in the late. '20's when conveyor mining was introduced. In this application, the equipment consisted of a chain conveyor with a face chain conveyor parallel to the face on which the coal was loaded by hand and, in turn, was discharged onto the room conveyor and thence to a loading point on the entry at the mouth of the room. Another method was to use a shaker conveyor with a duckbill which was maneuvered across the face of the room from which the coal was loaded and transported by the shaker to the loading point. In either case the equipment did not readily lend itself to driving crosscuts or breakthroughs with the result that rooms were driven to depths of 250 or 300 feet without adequate means of ventilating the face area with the main split of air. It was, therefore, necessary to use other means of ventilating this area as the rooms were being driven and during retreat work if pillars were extracted. Auxiliary fans of the blowing type were utilized for this purpose. They were of very small capacity using small diameter tubing. By the time the room was driven half way to its projected limit ventilation was very poor or practically nonexistent. To compound the problem the fan was usually set up at the mouth or neck of the room and in many cases the intake air to the fan was the return air from the room. It is small wonder, therefore, that there is on record 12 cases where auxiliary fans were given as the cause of explosions. In 9 of these occurrences, arcs or sparks from open-type motors or accessory equipment on these fans were given as the primary ignition source. They fell into such ill repute that in a number of cases they were blamed as the ignition source even though smoking was strongly suspected as the primary cause.

Jan 1, 1967

By D. P. Patil, T. C. Rao, J. P. Barnwal

Factorial design of column flotation experiments was used to understand the main and interactional effects of the column parameters. In the experiments, the air flog rate, the wash-water, flow rate and the froth depth were varied at two levels. Analysis of the results showed that an increase in airflow rate had a deleterious effect on the grade of the concentrate, whereas, an increase in froth height increased the grade. The interactions between airflow and wash water and between airflow and froth height were significant with respect to grade of the concentrate. These results demonstrated that, from an ore containing 12.76% P2O5, it is possible in a single-stage flotation column to obtain a concentrate containing 31 % P2O5 (10.6% Si02) with a recovery of 94%, thus reducing the number of cleaning stages that would be required if conventional flotation cells were used.

Jan 1, 1997

By S. Veeramasuneni, Qingxia Liu, Susan Dichter

Gypsum (CaSO4-2H2O) is an abundant and naturally occurring mineral. Under elevated temperatures (250 to 300°F) gypsum loses its crystalline water and is converted to hemihydrate (CaSO4 -0.5H2O). The hemihydrate form is also called plaster that is widely used in wall- board, joint compound, and many other industrial applications. At temperatures higher than 450°F (up to 1,200°F), gypsum loses all crystalline water and is converted to anhydrite form (CaSO4). The loss of crystalline water at elevated temperatures is an endothermic reaction. This property makes gypsum an attractive filler and fire retardant in certain thermosetting plastics. The applications of gypsum in plastics, food, pharmaceutical, and paper coatings will be reviewed in this paper. The future of synthetic gypsum, a by product of various industrial processes, will also be discussed.

Jan 1, 2003

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation was carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Test results showed that unconfined compressive strength of 40 MPa was achieved. In addition, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including scanning electron microscopy with energy-dispersive X-ray (SEM/EDX) analysis, Fourier-transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) spectroscopy were used to investigate the microstructures and elemental and phase compositions of the reaction products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.