Search Documents

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

The mineral industry uses significant amounts of water in processing. Thus, sustainable practices with the processing of ores are of critical importance. An impact tester was used to measure the adhesion force between particles and a glass disk [1,2]. A removal force was caused by the impact of the disk/particle containing a puck with a stopper. Johnson-Kendall-Roberts (JKR) theory [3] was used to determine the interfacial energy between the particles and the substrate. Capillary condensation of water can occur between the particle and surfaces in humid environments. The adhesion of particles on rough surfaces has been studied previously [4-10]. The research presented herein combines both variables to separate particle types with minimal water usage.

By Rolf Pollak, Jan Tegtrneier, Gerhard Keller, Horst Gerhardt, Wolfgang Müller, Dieter Tetzner

INTRODUCTION Under certain geological and mining conditions mining near the surface results in an intensive destruction of the overlying rock strata. If the system of mine openings remains filled with air after having completed all mining activities because the flooding of the mines depending on the morphology of the mining area does not exceed a certain level, this circumstance might result in dangers for the public. This is particularly true where uncontrollable air- ways occur within the destroyed rock or if former uranium mining areas are concerned. In these areas radon emanation resulting in undue radon concentration should be taken into account. This circumstance can be counteracted by suitable measures of ventilation. In the following the example of a uranium deposit in the Erzgebirge Mountains (Saxon Ore Mountains) is used to illustrate how statements about the ground flow through overlying rock can be made on the basis of systematic investigations. Finally comparisons with experience gained in coal mining yield orientation data which are used as input quantities in ventilation network calculations and in project preparation of mine fans. Last not least it is proved that endangering the population by radon can be excluded by installing an appropriate fan. INITIAL SITUATION From 1946 to 1989 the uranium deposit of Schlemal-Alberode was mined starting from superficial zones down to depths of 1,800 m. The total output amounted to 80,000 t of uranium, i.e. Schlemal Alberode is one of the largest uranium deposits in the world. The mine openings comprise a cavity of 40 million m3. Al- though thin seams (0.2 to 0.3 m) and steep to semi-steep veins (60 - 70 degrees on average) were extracted using the method of overhand cut-and-fill there were also deposit sections with larger thicknesses and poor ore zones, respectively, where especially after the war until about 1955 large openings were formed due to missing filling. Due to this uncontrolled, relatively "wild" mining considerable subsidence of the surface and fractures in the border zone of the subsidence area occurred. The town of Oberschlema was destroyed and an area of 0.14 km2 was damaged by mining involving a maximum subsidence of 6 m in the centre - called deformation area. The rehabilitation work for the deposit area of Schlemal Alberode involves the flooding of the openings up to a level of the Markus-Semmler-Sohle as long-term preventive measure. Fig. 1 shows the flooding level of October 1996. The level of the -540 m drift will probably be reached in June 1997. From that point of time a general rearrangement of the ventilation has to be made because the central return air ventilation via shaft 373 will no longer be possible. This shaft has no connection with the superficia1 system of mine openings. A new return air ventilation system based on shaft 382 as return air shaft will be designed (Fig. 1). The capacity of the future mine fan system will e.g. be determined by the flow conditions in the deformation area mentioned above. For this reason investigations were carried out in a test drift 13a on the level of the Markus-Semmler-Sohle in the stretching zone of the subsidence trough for several days (Fig. 2 and 3). INFLUENCE OF THE OPERATING CONDITIONS OF THE MAIN MINE FAN ON THE RADIATION SITUATION ON SURFACE The beginning of flooding in 1991 was also the beginning of the investigations into the options of future ventilation due to the reduction of the mining area. The first analyses of radon emanation made in May 1991 showed that only about 20 % of the total radon emanation result from systematically ventilated mine workings. This means that despite of existing dams the air streams through the majority of mine openings of the deposit. The analysis of the individual radon inflows illustrates the special problematic nature of the deposit involving all possible effects on the surface. The shutdown of the main mine fan over the long period between 2.10. and 6.10.1991 showed the essential influence of the operating conditions of the fans on the whole radiation situation on surface. Fig. 4 shows the comparison of the radon concentration level and its daughters during a 'normal" weekend with the level during long-term shutdown in the old 'Casino" of the papermill of Niederschlema. This papermill as well as the 'Casino" are situated in the outcropping zone of the deposit section of Niederschlema. The -60 m level was driven as the upper level in this area, from which the panels were driven to about 20 m below the surface. Also below the "Casino" there is such a panel in the vein 'Glirck", whose roof is directly situated below the building in a depth of 39 m. Directly next to it there is the raise 2 of the panel 'Namenlos" in a depth of 27 m. The graphics clearly shows the immediate increase in radon concentration as well as in the daughter concentration after the shutdown of the fans. The elimination of the artificially generated negative pressure results in the reversal of the convection direction due to the natural ventilating pressure. The interface structure allows the mine airto pass through aero- dynamic connections to the surface. Neglecting the meteorological parameters the concentrations of radon and its daughters in- creased by about 350 % as compared to a 'normal" weekend during longterm shutdown (i.e. in 4 days). Furthermore it could be noticed that a stationary state between the radon and its daughters has not been established in the period

Jan 1, 1997

By Roger B. Jr. Herbert

Surface water samples were collected from water accumulations at the surface of a neutral pH mine tailings deposit in Kristineberg (Sweden) where algal growth and iron hydroxide precipitates were observed. Ferric iron in the aqueous samples was determined by (adsorptive) differential pulse - cathodic stripping voltammetry. The analyses indicated that labile Fe3+ concentrations were in the range <20 to 337 nM, while total Fe3+ levels were much higher at 0.9 to 8.3 uM. The labile Fe3+ levels are more than two orders of magnitude greater than would be expected based on equilibrium with ferrihydrite. These results suggest that iron complexation with strong ligands in the surface water competes with iron hydrolysis, and that these ligands may be of algal and/or bacterial origin.

Jan 1, 2000

By L. George Imperato

The Blocked Iron Corporation has been active for many years in the development of mineral agglomeration processes by cold chemical induration. Millions of tons of iron ore fines agglomerated by their methods have been consumed in open hearth steel making furnaces. Some of you may remember these open hearth agglomerates as the carbonate-bonded cylindrical block shown in figure 1. With the realization that iron making would create the greatest demand for agglomerates our research efforts were directed to the production of carbonate- bonded (C-B) pellets containing iron ore, flux and carbon, shown in figure 2.

Jan 1, 1968

By P. D. Morrell

Jetbelt is the trade name for the air supported belt conveyor. It does not use troughing rollers. Jetbelt conveyors support the conveyor belt on a thin film of air. The belt rides in a steel trough which has small holes equally spaced along the bottom of the trough. Air comes through the holes under the belt, thereby supporting the belt. The air pressure is provided by a single centrifugal blower that creates very low pressure, between 249 Pa and747 Pa [10" and 30" water column], depending upon the tonnage being conveyed. The volume of air required ranges between .001415 m3/S and .00283 m3/S [3 and 6 CFM] per lineal foot of conveyor. Therefore, depending on tonnage being conveyed, a 304.8m[1000&apos;] conveyor might require as little as 1.415m3/S [3000 CFM] or as much as 2.83m3/S [6000 CFM.]. (See Figure 1) Horsepower requirements can be less than troughing idler conveyors and considerably less than some other forms of bulk conveying. Savings are most significant in horizontal and down hill (regenerative) conveyor designs. Horsepower to lift material, of course, does not change.

Jan 1, 1984

By Kenneth K. Humphreys

27.1-HISTORY, PROCESSING STATISTICS KENNETH K. HUMPHREYS 27.1.1-MINERAL PROCESSING HISTORY The processing of minerals predates recorded history. Many processing techniques have existed for thousands of years. For example, Georgius Agricola, in De Re Metallica (1556), described equipment and techniques, such as picking tables, smelting furnaces and cupolas of various types, sieves, launders. various types of crushers and grinders and other equipment, all still in use in one form or another. In translating Agricola&apos;s work into English, the late Herbert C. and Lou Hoover provided the following summary indicating the early history of particular mineral- processing operations :

Jan 1, 1973

By C. D. Hebert, T. Gregor, M. Ghazi, G. J. E. Kramer

This paper describes the recent application of gasketed, precast concrete segmental lining design that has improved tunneling productivity and quality. The speci?c segment arrangement includes: six-piece ring with equal 60 degree gasketed segments, juxtaposed key and counter-key segments, trapezoidal and parallelogram shaped segments, inclined and skewed radial joints and plastic circumferential joint connectors. This allows rapid, but accurate ring erection, reducing mine cycle times. The design avoids cruciform joints, minimizes potential gasket damage and eliminates the need for separate left and right ring molds. The implementation on the Los Angeles ECIS and NEIS sewer projects is described.

Jan 1, 2003

By Michael Day, Paul Kos, Scott Brinton

Quantitative hydrogeologic characterization of fractured rock is challenging because fracture systems are convoluted and difficult to characterize discretely. For large-scale water resource impact analyses, it may be more appropriate to use a watershed water balance approach and analyze fractured systems in terms of “bulk” hydraulic parameters over a large enough scale (hundreds of meters), so that the fractured media may be evaluated as “equivalent” porous media [1]. This is a common investigative methodology for mountain watersheds in fractured bedrock terrain because it does not rely on discrete flow paths but instead evaluates inputs to (recharge) and outputs from (discharge) the ground-water system [2,3]. This paper describes the use of this methodology to perform a practical and cost-effective hydrogeologic characterization and mining impact analysis for a proposed granite quarry in a mountain watershed. The key conclusions of the study guided the mine planning that was designed to minimize impacts to the fractured granite hydrogeologic system and preserve recharge to downgradient sedimentary aquifers.

By P. Legast

Serpentinite minerals are available in large quantities from asbestos mining activity. The granular or fibrous serpentite, at temperatures greater than 700°C, will recrystalize into olivine, forsterite and enstatite. These minerals have been used and studied for decades and are environmentally safe. The thermal process changes the composition and properties of the original mineral. Therefore, the substitution of the original mineral cannot simply be made and the applications for these new synthetic minerals need to be redeveloped. The two original mineral forms allow a wide range of new synthetic raw materials which can be adjusted to specific applications or custom needs.

Jan 1, 1993

By J. A. Arias

The oxidation kinetics of pyrite and refractory gold concentrates in acidified ferrous sulfate solutions in the presence of oxygen-sulfur dioxide gas mixtures has been studied. The effect of temperature, pulp density and gas composition were determined. The optimum oxidation rate was obtained at 80°C and 2 percent sulfur dioxide in the gas mixture. The oxidation of the sulfide minerals is attributed to the presence of ferric ions, which are continuously regenerated by the gas mixture. The objective of this study is to find a new hydrometallurgical method to render sulfidic refractory gold ores amenable to cyanization.

Jan 1, 1993

By Gregory A. Hope, Kym Watling, Matthew I. Jeffrey, Ronald Woods

Surface enhanced Raman Spectroscopy carried out in real time has been applied to identify surface species formed during gold leaching in chloride and thiosulfate media. Chloride ion is adsorbed prior to the gold dissolution potential, but its coverage is significantly diminished at the beginning of leaching. A gold chloride band is again observed when dissolution is rapid, together with bands characteristic of AuC14- ions in solution. With thiosulfate, a thin gold sulfide layer is formed slowly in the potential region where leaching occurs. At higher potentials, thiosulfate is oxidized to sulfur and sulfate, both products being identified by Raman spectroscopy.

Jan 1, 2005

By Kyle Amoroso, Aaron K. McCain

Frozen soil shoring has been used for decades in the tunneling industry to provide temporary support of excavation for shafts and cross-passage excavations. However, horizontal penetrations through the frozen soil can prove to be challenging. The key to creating a stable portal through frozen ground is managing and mitigating groundwater flow into the excavation through the annular space surrounding the drill stem or casing. This paper will review different approaches that have been successfully used to penetrate frozen soil shoring on multiple projects.

Jun 13, 2023

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted byproducts generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining, (2) dyke construction schedule, (3) size, shape and location of tailing cells and (4) mining and processing production targets. The results show that in creating in-pit tailing-cell designs, decreasing the mining-cell volume and increasing the number of mining cells improves the net present value (NPV) of the operation due to increased operational flexibility.

By W. Moser

During the ten year span from 1978 to 1987, the number of fires which occurred in under-ground coal mines doubled from the previous ten years. Anyone involved with underground coal mines is well aware of the associated tragedy that can result from these fires, both to personnel and to property. Every day mine management and mining personnel face this threat of a possible mine disaster or fire. Their ability to deal with such a situation safely and effectively depends on the level of emergency preparation developed and maintained. As a direct result of the ever-increasing interest in the Mine Emergency Preparedness Program and the Mine Fire Training Programs currently being conducted, the Emergency Preparedness Center was created. As a branch of the Mining Extension Service at West Virginia University, the Center provides preparedness training at several different levels on a varying range of topics. Classes are conducted at a new especially-designed training laboratory at the National Mine Safety & Health Academy in West Virginia. By maintaining the proper equipment and levels of training allowing for immediate response, the personnel who are part of the Center believe that the impact of a mine fire or other such emergency situation can be minimized. This paper will present recommendations for maintaining an efficient mine emergency preparedness program and will provide information regarding the Mine Fire Training Program as conducted by the Emergency Preparedness Center and describe the advantages of the newly constructed training facility.

Jan 1, 1993

By WILLIAM M. CROSS, ALBERT ROMKES, BERNARDO MORENO BAQUEIRO SANSAO, Jon J. Kellar

The mineral industry uses significant amounts of water in processing. Thus, sustainable practices with the processing of ores are of critical importance. An impact tester was used to measure the adhesion force between particles and a glass disk [1,2]. A removal force was caused by the impact of the disk/particle containing a puck with a stopper. Johnson-Kendall-Roberts (JKR) theory [3] was used to determine the interfacial energy between the particles and the substrate. Capillary condensation of water can occur between the particle and surfaces in humid environments. The adhesion of particles on rough surfaces has been studied previously [4-10]. The research presented herein combines both variables to separate particle types with minimal water usage.

By Guerry H. McCullen, Bruno Despujol

Quartz and phosphate grains from concentrates and ores from Atlantic Coastal Plain sediments often are wholly or partially coated by humates. Coatings were studied in situ using infrared microscopy, by transmission Fourier transform infrared of extracts, and scanning electron microscopy. The 14C age of the coatings is about 20,000 years, much younger than the mineral substrates. Coatings on double flotation concentrates indicate that the conditioning pH may be too low, allowing coated quartz grains to follow phosphate grains through beneficiation. Organic matter from coatings may contribute to processing problems as well as affect final product quality.

Jan 1, 1999

When most people think of coal mining, they envision men in soot-covered clothes and hard hats digging at deposits in deep underground caverns. These mental images commonly include coal cars rumbling on rails as they emerge from the earth, filled to the brim with rocky ore. The world of modern, longwall coal mining is a far different place. Yes, it?s underground, the miners still wear hard hats and the environment is filled with soot. However, today?s mining operations are carefully monitored and the entire process is highly automated. Five kilometers (3 miles) underground, a sophisticated, high-powered mining machine moves steadily through a 2-m (6-ft) high tunnel at an average speed of 3.2 km/h (2 mph), carving out coal, then conveying it to a crusher and carrying it to the surface. Instead of digging out the ore, a longwall mining system slices it from the exposed tunnel face, using giant rotating shears. The shorn coal tumbles onto a conveyer below the shears and is conveyed to the stageloader, where it is crushed and dumped onto the main conveyer belt that eventually hauls it out of the mine. Integral to the longwall shear and conveyor is a moving metal roof that protects it from the thousand plus feet of ground above. The ceiling panels automatically advance above the shears, powered by hydraulic roof supports that stand on the other side of the tunnel, moving in a slow, sideways lock-step with the shears. This complex and massive machine makes longwall mining the most ef?cient and productive method for excavating coal. In fact, it produces 2.7 kt to 22.6 kt (3,000 to 25,000 st) of ore per shift, versus 544 to 907 st (600 to 1,000 st) for the conventional room-and-pillar mining. Using that method, miners develop one section of a mine at a time after carving out load-bearing columns of coal to support the roof above their heads. Longwall mining also is considered safer than the room-and-pillar method, largely because the process is mostly automated, requiring fewer workers. Still, longwall mining has its drawbacks: The equipment is expensive and the mining conditions are harsh. An entire longwall system can cost between $50 million and $100 million, while the electrical controls used to operate it can cost an additional $1 million to $2 million. These investments grind away all day, every day, in hot tunnels filled with coal dust.

By Heinz Hoberg, Fred Ulrich Schneider, Rudolf Diegel

The risk of contamination of dumped tailings and ground water by coal flotation reagents has been investigated by using the 14C-radiotracer method for adsorption and desorption measurements. The results indicate, that a high amount of the reagent components adsorbed on the tailings if there was no coal in the pulp. In coal flotation however a competitive adsorption behaviour could be observed, with the effect that only a low quantity of reagents adsorbed on the tailings. Mobilization tests showed, that only small quantities of reagents could be desorbed by rinsing water. Therefore the contamination of ground water should be low.

Jan 1, 1995

By Fabio Mielli

The mining industry is a multifaceted industry with special characteristics that make efficient and intelligent operations uniquely challenging, and subsequently call for distinctive and tailored solutions. Not only does mining call for processes that are complicated and energy intensive, but complex material movements and an intricate logistical chain add to the industry?s obstacles in achieving sustainability and performance. This article explores three major challenges and the resulting issues currently being faced in the industry, as well as potential solutions to these impediments by use of energy management, automation and control strategies.

Jan 1, 2011

By Robert S. Ondrey, Robert A. Haney, Kenneth G. Fields

As part of an MSHA program to assess the effectiveness of dust control parameters for longwall mining operations, respirable dust studies were conducted on six longwall sections. The purpose of these studies was to evaluate the influence of airflow and production on longwall dust control. The sections were sampled for 3 to 35 shifts. In addition to dust, ventilation and production measurements, other dust control and operational parameters were measured. The water spray system at each operation conformed with generally recommended practices. Therefore, improvements to the dust control system would be most appropriately achieved through improvements to ventilation along the face. Two methods of assessing the influence of ventilation and production were used. For two of the six mines where extensive sampling (22 and 35 shifts) was conducted, multiple linear regressions were used to relate the dust concentration versus airflow and production data. For these two mines, statistically significant correlations existed between concentration and both production and airflow. The multiple regressions fit to the data indicated that for every 0.47 m3/s (1,000 cfm) increase in airflow, there would be approximately 0.04 to 0.07 mg/m3 reduction in dust concentration; and, for every 1,000 ton increase in production, there would be approximately 0.15 to 0.50 mg/m3 increase in dust concentration. For the four mines with limited data (3 to 10 shifts), as well as for the two mines with extensive sampling, an average ratio of airflow per ton of coal mined was calculated by proportioning the airflow to production and the designated occupation personal respirable dust exposure to a 2.0 mg/m3 concentration. The airflow-to-tons ratio required to maintain a 2.0 mg/m3 dust concentration ranged from 0.0038 0.0071 m3/s per ton (8 to 15 cfm/ton). Both of these data treatments were used to calculate airflow requirements based on normal production rates. For the two mines where both the regression and airflow-to-tons ratio were calculated, results from the two methods agreed within 25 percent.

Jan 1, 1993