Search Documents

By Douglas N. Kendall

There are three definite steps in the making of a mining industry in any country. These are as follows: Step A - Geological Mapping This step covers the basic geological mapping of the country at scales of 1/250, 000 up to l/50, 000. This step eliminates territory and directs the exploration teams to the areas of potential interest. Step B Prospecting This step includes all phases from detailed geology through geophysics and drilling up to the point of proving that an economic ore body exists. Step C - Mine Development This is the expensive step, involving the creation of the mine, including shaft-sinking, ore treatment plant, etc.

Jan 1, 1963

By P. Bevilacqua, G. Vallebuona

Empirical models are now used for predicting the performance of hydrocyclones in terms of capacity. cut size (d50.c), water split and partition curve. These models (such as the model by Lynch and Rao and the model he Plitt) were developed and checked for hydrocylones with diameters larger than 4 in. However, for smaller-diameter hydrocyclones, little empirical modeling has been done. This paper reports on an extended experimental research program on small hydrocyclones. For these cyclones, the suitability of existing empirical models was investigated and their accuracy was compared. To improve the predictive capability of these models to small cyclones modifications to the equations are proposed.

Jan 1, 1996

Energold Drilling Corp. is a leading specialty drilling company servicing the mineral and energy sectors in the Americas, Africa and Asia. Energold specializes in mineral exploration in remote locations with limited infrastructure. Such locations require the smallest footprint possible going in, leaving as little or no evidence on their way out. Energold?s rigs can be transported by helicopter or manually on footpaths as narrow as 1 m (3.3 ft). They set up quickly and then are struck and packed out, with any sign of their presence quickly disappearing behind them. Energold has teamed up with Atlas Copco and its team of engineers in North Bay, Ontario to design small rigs capable of drilling to a variety of depths, as required for each project.

Jan 1, 2013

By Timothy J. Haddon

For the mining industry in general and gold mining in particular, the past few years have been difficult. Economic conditions, coupled with growing regulatory restrictions, have led to increasingly important reasons for managing assets wisely. From a public company perspective, such asset management makes sense because it ultimately provides for an increase in shareholder wealth, and that is why we are in business. Regardless of whether a company is public or not, assets must be managed effectively to remain a player in today's competitive environment. So, as the chief executive officer of a gold mining company, how do we manage our assets to ensure that we are satisfying our obligations to our customer-the Amax Gold shareholder? The gold industry has been under siege. We have just completed the third year with average prices below $12.85/ g ($400/oz). When finding, and/or acquisition costs and development costs to operating costs are added, there isn't much of a profit margin left. What this environment provides, however, is opportunities for growth. In the gold business, you either grow or you die. Today, most North American gold producers have, at most, a 10-year mine life. We are all scrambling to add reserves so we do not become extinct. As prices remain low, opportunities abound for increasing diminishing reserves. This is the time for the opportunistic company to take advantage of market conditions and that is precisely what Amax Gold has done. There are six components to running a successful gold business: • finding reserves through exploration, acquisition or joint venture, • financing the project, • permitting and constructing the project, • operating the project, • cash management and • communication.

Jan 1, 1992

"Tell us how you got involved in mining?I was first exposed to mining at a young age, as a consequence of my dad and his passion for the industry and rock collecting. Even though he graduated with a degree in mining engineering from Washington State University, my dad spent most of his career working as a structural engineer for the Boeing Company. At the time, Boeing supported a range of employee activities and clubs, including one devoted to mineral prospecting, small-scale dredging and rock hounding. My dad was extremely active in the Prospectors Club, where as a family, we spent a good part of my youth tramping around the Pacific Northwest digging for mineral specimens and panning for gemstones and gold. On my mother’s side of the family, I had relatives that mined in Dawson City and Fairbanks, AK which left a family legacy of sorts. I loved the stories that my dad and a close buddy of his, who was a geologist, would tell about various operations and towns, as well as the wild times at the annual Northwest Mining Association (NWMA) meeting in Spokane, WA. My first recollection of ever being at a commercial operation was during a tour of the Bunker Hill Mine with my dad when I was 7 or 8 years old; this had to have been shortly before the May 1972 fire at Sunshine. That visit of the mine and processing facilities made a permanent impression on me. While I always knew there was something special about the Silver Valley, I began to understand why. To this day, I still get the same feeling when I visit historic mining districts like Leadville, Morenci, Virginia City, Butte, Silverton and Barkerville. During our summer excursions to Helena, MT to dig sapphires, we would usually make visits to Butte and watch mine operations inside the Berkley Pit and surface activities at the Kelly and Mountain Con. In high school, I did well in math and science and began entertaining thoughts of pursuing a degree in engineering. Above all, I wanted to go to a college in the West that had a good academic reputation, where I could also play football. As a 6-ft, 190-lb nose guard, my options for a Division I scholarship were pretty slim, and there weren’t that many technical schools in the Northwest that were Division II that offered athletic scholarships. As fate would have it, I was unexpectedly contacted by Marv Kay, a legendary coach at the Colorado School of Mines (CSM), and was recruited to play ball. Fortunately, I had a couple of high school friends who were already attending CSM, and I had just secured a summer internship with Asamera Minerals in Wenatchee, WA. It was as if all the stars had aligned, and, with the support of my parents, I made the decision to attend Mines. Despite the stress of getting through CSM during a period when the mining industry was in freefall, it was a great decision to attend Mines, and I’m thankful for all the opportunities, friendships, and faculty mentoring I received as a student"

Mar 1, 2019

By Fernando H. Muge

The first application of dynamic pro¬gramming to the problem of grade control and scheduling was by Muge et al (1979) and Ribeiro (1982) who applied it to the simple, two-dimensional case of longitudinal open stoping using two sublevels. In this paper the formulation of the problem is extended to cover the general case applied to a cut-and-fill mining method. The criterion for optimization is the total deviation of the average, grades of mining blocks from the overall average panel grade (or the average grade of a set of mining panels or the mine processing working point). This means to schedule the operation by removing a certain number of mining blocks at a time, subject to the geometric (mining) constraints, and such that the total deviation of average block grades from overall average grade is minimum. The method can be applied to complex orebodies with several ore characteristics and the deviation of each one of these characteristics can be further constrained by specifying maximum values. The method can also be generalised in order to take into account any necessary geometric constraints used to define the mining method. In this paper a case study is presented concerning the mine planning of a complex sulphide orebody located in the South of Portugal. As input for the definition of the mining sequence, a geostatistical numerical model of the orebody was built based on a previous ore typology. The short term planning is used to assess specific mining sequences and the production scheduling is performed on the basis of an objective function (e.g. minimization of grade fluctuation).

Jan 1, 1989

By D. Leppert

Clinoptilolite zeolite may offer attractive, cost-effective alternatives for remedial cleanup of old minesites, smelters and other sites with heavy metal contamination. Previous research demonstrates the relatively strong affinity of clinoptilolite for numerous metals and clinoptilolite displays a particularly strong affinity for lead (Loizidou and Townsend, 1987), one of the most toxic and problematic heavy metals. Since clinoptilolite can also selectively absorb some radionuclides and organic compounds, it may offer practical solutions to a wide variety of environmental problems.

Jan 1, 1989

By J. D. Megeath

In the October 1988 issue of MINING ENGINEERING, J.G. Wargo's paper discusses the problem of measuring and analyzing permeability, porosity, and fracturing in its relation to in situ leaching of disseminated gold deposits. This paper made me suspect that a good deal of information and analysis may have been done on this in reverse in the petroleum industry. Some years ago, I was involved with the US Geological Survey in a project studying the Devonian shale of the eastern United States. The Devonian shale contains gas deposits that have the characteristic of slowly seeping gas over a very long time period. To understand the rate of seepage, considerable study and analysis was done on the interrelationship of poros¬ity, permeability, and fracturing. The purpose was to find out how and why the gas could escape in the varying rates found in wells throughout the formation. It strikes me that this is the mirror image of the problem faced in attempting to understand how a cyanide solution will travel into a deposit. To possibly invent our own personal wheel a little faster, I would suggest a look at the work done on the Devonian shale. Some of it is contained in "Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," US Geologi¬cal Survey Open-file Report 82-474, 1982, and "Additional Data for the Estimates of Unconventional Natural-Gas Re¬sources of the Devonian Shale," Open-file Report 83-676, 1983. It is entirely possible that some of this previous work could shorten the time required to make in situ leaching of dissemi¬nated gold deposits a profitable technique.

Jan 1, 1989

By J. D. Megeath

In the October 1988 issue of MINING ENGINEERING, J.G. Wargo's paper discusses the problem of measuring and analyzing permeability, porosity, and fracturing in its relation to in situ leaching of disseminated gold deposits. This paper made me suspect that a good deal of information and analysis may have been done on this in reverse in the petroleum industry. Some years ago, I was involved with the US Geological Survey in a project studying the Devonian shale of the eastern United States. The Devonian shale contains gas deposits that have the characteristic of slowly seeping gas over a very long time period. To understand the rate of seepage, considerable study and analysis was done on the interrelationship of porosity, permeability, and fracturing. The purpose was to find out how and why the gas could escape in the varying rates found in wells throughout the formation. It strikes me that this is the mirror image of the problem faced in attempting to understand how a cyanide solution will travel into a deposit. To possibly invent our own personal wheel a little faster, I would suggest a look at the work done on the Devonian shale. Some of it is contained in "Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," US Geological Survey Open-file Report 82-474, 1982, and "Additional Data for the Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," Open-file Report 83-676, 1983. It is entirely possible that some of this previous work could shorten the time required to make in situ leaching of disseminated gold deposits a profitable technique.

Jan 1, 1990

By Lee F. Robinson, Angus W. Morrison, Norman M. Anderson

About 100 years ago the acid and chlorine oxidation routes for gold extraction were abandoned in favour of cyanide/ oxidation processes. Now a return to acid processing is in progress. One publication in particular led HM C Technology to investigate the reaction of dilute nitric acid and alkaline metal chlorides with refractory gold ores.(l) The one stage system of gold and silver recovery from sulphidic ores is described below. It is rapid and does not use large or expensive plant or special pressure equipment. It eliminates calcining followed by cyanidisation and shows a simple way of recovering the gold directly. Patents have been granted in some countries (2).

Jan 1, 1990

By J. J. Bartels

The phosphate rock review did not arrive in time for publication in the. June issue. The world phosphate industry continued its slide in 1992 from the already depressed levels in 1991. The industry is locked into a 30-year fertilizer price low due to the worldwide fertilizer glut. Domestic production and imported, marketable phosphate rock decreased 1%, while domestic consumption increased by 1 % last year. The US Bureau of Mines reported a decrease in the domestic phosphate rock value from $25.42/t in 1991 to $23/t in 1992 ($23.06/st to $20.80/st). The diammonion phosphate (DAP) product price also dropped in value from $138/ t in January 1992 to $11 0/t in December ($125/st to $99.70/st). Continued declines in DAP prices is forcing the US fertilizer industry to develop cost-saving programs and reorganizations. Layoffs in 1992 resulted in a 7.6% decrease in the Florida phosphate workforce. Since 1980, the Florida workforce has declined by 35%. Small phosphate companies were forced to close operations or were sold to larger phosphate companies. Federal and state environmental regulations for byproduct waste disposal methods are being studied. The Environmental Protection Agency (EPA) approved phosphogypsum use in agri¬cultural and research applications as long as the radium 226 concentration is lower than 10 pci/g. The EPA is also reviewing regulations concerning air emissions at fertilizer plants. Industry publications reported the possibility of continued company sales and mergers in 1993. Industry expectations are optimistic while waiting for an upturn in the market. The US phosphate industry consolidation into three or four major companies should evolve into a stronger world market force.

Jan 1, 1993

By José Ricardo Lopes, Alaor Coelho, Marco Gomes, Alfredo Dacio Moraes Filho, Akira Koshima

"Very low strength alluvial peat soil was found under two old drainage galleries with just 4.3m cover above a twin tunnel due to be excavated by a 10.6m diameter EPB Shield for São Paulo Metro’s Line 5. Alignment was required to strengthen soil and drive the TBM through safely without damaging the galleries. The design included six levels of self-drilling forepoling with lengths up to 15m, using 100 mm-diameter SCH160 metal tubing and injection bulbs with estimated 0.20m diameter. Two 6m-diameter circular shafts were excavated along the shield-tunnel axis, one each side of the galleries, and forepoling fanned out under gallery foundations. Given the peculiar soil and confined working space, more data were needed for correct drilling geometry. Ground mass treatment was successfully designed and executed and galleries were fitted with instruments to enable the shield’s advance. DESCRIPTION São Paulo Metro’s Line 5 (aka Lilas or purple line) is adding 11 stations along an 11.5km extension and three EPB TBMs are being used simultaneously (three EPBs on the same job for the first time in Brazil) with one of them excavating a large cross- section twin-track tunnel. Currently the largest work-in-progress for São Paulo Metro, this project has been divided into seven lots and 9km are already operational. This study refers to Lot 6 where the 10.6m - diameter EPB shield excavation is only 4.3m below two galleries running through a 10m layer of very soft peat soil in an old alluvial riverside region ringed by major roads. After recent filling, this area (Parque das Bicicletas) was used for recreation, although temporarily it has become a construction site. This paper will describe the original basic design; precautions in relation to the structural condition of the galleries after inspection; the problem of absence of data for their foundations; subsoil bore tests; evolution of the engineering design for the galleries and conditioning and reinforcing the soft soil below the galleries to ensure safe advance of the EPB shield, and finally the successful outcome of the solution used."

Jan 1, 2016

By Lauren M. Roberts, Ralph R. Sacrison

The Meikle Mine uses long-hole open stoping and cut-and-fill methods with backfill as the primary ground support technique. The mine operates at 2,858 tonnes per day (3,150 tpd) and has sustained operation in excess of 3,175 tonnes per day (3,500 tpd). Consistent backfill production is critical in achieving these mining rates. The heart of the system is a 7.65 cubic meter (10-cyd) horizontal shaft ribbon mixer located 328 m (1,075 ft) underground. System control is through several PLC's, allowing for a high degree of automation and process flexibility. Aggregate feed is routed 257 m (842 A) through vertical drop pipes in the ventilation shaft, a rockbox, transfer raises, and then into either of two raisebored storage silos. The aggregate is crushed mine waste, nominally 70% 3.8 cm x 1.0 cm (1-1/2"x 3/8") and 30% -1.0 cm (- 3/8"). The binder is routed through a vertical borehole, surge bins, and transfer raises. The binder is a mixture of Type II cement and fly ash. Two primary manufactured fill designs are produced: a high strength mix for stopes which will be undercut; and a low strength mix for stopes with only rib exposure. The high strength target is 5.5 Mpa (800psi) unconfined compressive strength in test cylinders. The low strength target is 2.8 Mpa (400 psi). The systim has allowed consistent achievement of these targets, while experience has allowed reduced costs and increased efficiencies. Fill placement is through 6.1 cubic meter (8 cyd) LHD's dumping into stopes. Specific sills and cut-and-fill drifts are jammed to the back. System enhancements have included colloidal mixers for cemented waste slurry placement and transfer raises for sending manufactured fill to the lower levels of the mine.

Jan 1, 2001

By Gerald L. Finfinger, Michael A. Trevits

Since 1964, the US Bureau of Mines has been conducting a comprehensive program of research on the origin and control of coal bed gas. Several extensive databases have been developed during the work representing information from every major coal producing region in the United States. Gas content measurements have been made on 885 coal samples from 15 states representing 221 coal beds. Records indicate that the range of gas content varies from zero to over 640 ft3 per ton (20 cm3 per gm). During the conduct of the research program, several drilling and completion techniques have been developed or refined to divert and collect coal bed gas before it enters the mine environment. Such techniques include horizontal, cross-measure and vertical boreholes. Samples of gas collected from boreholes drilled under the program indicate that the primary gas constituent is methane which comprises 97 pct, the remaining hydrocarbons make up approximately 0.2 pct. Nitrogen and carbon dioxide account for the majority of the remaining gases at average concentrations of 1 pct each. Surveys have been made on the total daily gas emissions from underground coal mines. In fact, the most recent survey indicates that 180 mines had emissions in excess of 100 Mft3 per day (2.8 Mm3 per day). Furthermore, total mine emissions were in excess of 300 MMft3 per day (8493 Mm3 per day). An analysis of the data showed that there appears to be no relationship between in-place gas content and coal bed gas composition. Furthermore, no correlation was observed between in- place gas content and daily mine emissions. In a general sense, the higher the gas content the higher the relative gas emissions. Perhaps a more direct relationship would be observed if more complete emissions information (including gob gas borehole production) was available.

Jan 1, 1989

By Michael P. Evans

Traditionally in coal processing jigs have been used to clean the coarse coal fraction, the +3/8" or +1/4" material. Today with the advent of modern fine coal jigs in the United States, its place was moved from the coarse to the inter- mediate coal circuit, the 3/8" x 100 mesh. The most economical coarse coal circuit to build and operate is a heavy media bath circuit. The following table summarizes the cost per raw coal ton processed for a coarse coal jig circuit, and a coarse coal heavy media bath circuit. The flowsheets used to compare these two circuits are shown in Figures 1 and 2.

Jan 1, 1983

By SAMUEL A. LOLON, ADITYA JUGANDA, JURGEN F. BRUNE, JR. GREGORY E. BOGIN

Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of explosive methane-air mixtures, herein referred to as explosive gas zones (EGZs) [1]. The risk of mine explosions can increase if these EGZs migrate out from the gob into the surrounding mine entries — a phenomenon known as gob breathing. A number of 3D computational fluid dynamics (CFD) simulations using various magnitudes and periods of barometric pressure variation have indicated that the EGZ outgassing potentially occurs due to lags in pressure, which are strongly influenced by mine conditions and ventilation systems. Early-warning systems with real-time pressure monitoring and the application of gob ventilation boreholes are recommended to detect and mitigate explosion hazards from gob outgassing.

By JURGEN KRETSCHMANN

The European climate and energy framework for 2030 is highlighting the reduction of man-made CO2 by increasing the use of renewable energy. In this spirit, Germany has decided to erase coal use as an energy source by 2038 completely. This strategy premises a feasible, responsible and sustainable post-mining management. The Research Institute for Post-Mining (FZN) at the TH Georg Agricola University in Bochum, Germany, has developed a holistic approach to meet post-mining challenges. In all efforts, the FZN aims to achieve the fundamental goals of the United Nations to deal with the resources of our planet responsibly and sustainably.

By Jennifer King, Julius Strid, Steve Brandon

The Upper Hidden Basin Diversion (UHBD) tunnel was driven approximately 1.2 miles by the drill-and-blast method primarily through massive granite bedrock geology for the Kodiak Electric Association, Inc. (KEA) in Kodiak, Alaska. The tunnel was driven from both portals with a constant 11-ft straight-leg horseshoe cross-section. The design and construction of the tunnel was driven by logistics and weather conditions due to its remote location and the rugged terrain of the project setting. This paper will discuss the successful completion of a challenging project over a ve-year period from preliminary planning through the design and construction phases.

Jun 23, 2024

By Gary MacDonald

What is the primary function of an impact assessment? Many people at the International Association of Impact Assessment?s (IAIA) annual conference said that it is time to return to the fundamentals and consider the underlying drivers of impact assessments ? human health, safety and security. This fall, managers struggling with those fundamentals will receive extra support when a new course focusing on health and socially responsible security is launched online and in British Columbia, Canada, home to many of the world?s junior miners. Now in its 33rd year, the IAIA conference recently held in Calgary, Canada, typically brings together a range of professionals who work in the impact assessment field, including academics, as well as people conducting applied disciplines, such as social and environmental performance management. It is a chance for people grappling with how to assess impacts from projects (for example, dams, mining and other extractive projects), to compare notes and to talk about developments in how to measure, track and report on them. The comments about returning to fundamentals rose as participants talked about the ongoing and increasingly recognized divergence between three main impact assessment streams: environmental, social and health (EIA, SIA and HIA, respectively). Discussions in sessions and in the corridors included calls for streamlining, for integration, for improvement and sharing of practice ? particularly in the HIA stream, where those deeply engaged in the health discipline questioned how HIAs and their intended outcome of protecting human health can be better integrated into the EIAs or SIAs that dominate the impact assessment realm. EIAs and SIAs have become the main tool, particularly from a permitting perspective for large-scale mines, but seem to leave projects with little real information about what they need to do. Human health is not the only concern re-emerging. Although not reflected at the conference, there appears to be an emerging understanding of the need to link the determinants of health with socially responsible security practices. Companies conducting independent social performance assessments for international financial institutions based on the International Finance Corporation?s Environmental and Social Performance Standards increasingly wrestle with both community health and security issues as extractive companies encounter challenging social environments around the world. Once again, the intended outcome is to better protect human health, including avoiding health impacts from conflict, abuses and violence.

Aug 1, 2013

By Hakan Uyguçgil, Beril Bayraktar, Adnan Konuk

In mining, which is one of the industries with the highest risk of occupational accidents, a primary goal is to enhance safety through the thorough investigation of accidents using reliable methodologies. In this research, the data from 13,653 accidents reported in the Karadon Hard Coal Enterprise between 2000 and 2011 were analyzed and compared using the life-table and Kaplan-Meier methods. Accident records were classified and analyzed into four categories: environment-related, equipment-related, person-related and other accidents. Findings in terms of survival time indicate that environmentrelated and person-related accidents had the highest risk in Karadon, with equipment-related accidents having the lowest. This study established the reliability of using survival analysis methods to investigate occupational accidents in the mining sector. Given that environment-related and person-related accidents occur in a relatively short period, such as one year after starting work, it is recommended that research be done to improve workplace and occupational safety measures and broaden the training given to miners. Additionally, it is determined that increasing the use of automation and mechanization in underground coal mines, combined with developing a thorough equipment safety training program to raise awareness of the danger, can help prevent person-related occupational accidents caused by the interaction between equipment.

Feb 1, 2024