Search Documents

By R. D. Herron

Mining coal under deep cover conditions is certainly the proper phrase to use in describing one of our newest operations. Located in the southwest corner of Virginia is this operation which is the Beatrice Mine of the Beatrice Pocahontas Company, a joint venture of Republic Steel Corporation and Island Creek Coal Company. The mine is working in the No. 3 Pocahontas seam in an assigned area of over 9500 acres containing over 60 million tons of recoverable, high quality, low volatile coal. The site of the mine opening was at Keen Mountain, Virginia, where the seam lay 1350 feet below the surface. This depth, greater than anything attempted thus far in the coal industry on this continent, would pose some problems, we felt, with which we had not previously had to contend.

Jan 1, 1968

By K. J. Stanaway

Concentrations of minerals between 3.5 and 5 specific gravity such as ilmenite, rutile and zircon in large accumulations of sand constitute "heavy mineral" placers. Two fundamentally different modes of formation characterize "trap" and "bed" placer variants. Smaller and generally higher grade trap placers form during sediment erosion or reworking. Because of their smaller size, they rarely yield economic heavy mineral deposits. They become economic, either if they contain more valuable "heavies" such as gold, or, if they occur within or near much larger but lower grade bed placers. Bed placers form during sediment accumulation episodes in any environment and lithofacies where mineral supply and fluid dynamics are favorable. Three heavy mineral deposits are discussed to illustrate bed placer geology and how trap placers occur with and relate to them.

Jan 1, 1991

By Y. Guan

The dissolution behavior of silver in ammoniacal solutions with cupric ammine as an oxidant has been investigated using a rotating disc electrode. The rates of dissolution of silver were determined by an electrochemical means as well as a direct measurement of silver ions reported in the bulk solution as a function of time. The variables investigated included stirring speed, temperature, concentration of lixiviants, and pH of the solutions. The rate of dissolution under the conditions studied' was found to be controlled by an electrochemical reaction at the liquid/ solid interface with an apparent activation energy of 48.07 kJ /mole. The rate was found to be a half order with respect to the, concentration of cupric tetra-ammine, Cu(NH3)l+.; The results were explained in terms of a mixed' potential theory.

Jan 1, 1994

By Paul Kents

The Canadian Javelin Limited Cerro Colorado copper-porphyry deposit in Panama, possibly the largest known copper-porphyry, contains between 1350 and 450 meter elevations, drill proven and probable ore in excess of 3.0 billion tons averaging 0.65% of copper equivalent. The deposit is located in the Central Cordillera Range, straddling the Continental Divide at 1500 meter elevation. Local topography is very steep. Accessibility is difficult, all logistics made by helicopter, and only recently a 52 km. road from the Pan-American highway was completed into the area. The deposit was discovered in 1969, and since then 75 shallow exploratory holes and 98 deep holes, the deepest 1340 meters, totalling 45,000 meters have been drilled. Deep holes were drilled at the corners of a regular rectangular 150 meter grid.

Jan 1, 1975

By Lee A. Goetz

Cost control is a lot like motherhood - everyone proclaims its need and its worthiness, but is it really appreciated and used to successfully complete a project on time and within budget? Good Cost Control is a yardstick - requiring fixed definition but this does not mean rigidity for the project. It provides the means for telling: 1. Where you are going 2. When you will complete and 3. What it will finally cost. Cost Control does not fix the price of dreams nor the cost of projects loosely defined. It does not control costs in itself but provides the tools whereby engineering decisions can be made which will ultimately affect the project cost It does not even guarantee that a project will be completed within the original funds - but only, if this reflects management desires.

Jan 1, 1970

By Don Reining

The sand and gravel industry in Southern California has made a sizeable contribution to the construction development of the 15 County area in this part of the State. Facing this mineral extraction industry, in the next decade, is a problem of meeting the market demand. The question is, "how can sand, gravel and rock operations be made compatible with goals for sound and attractive community development?" Three basic principal characteristics of the land needed for this-mining industry are: 1. The land must have workable sand, gravel or stone deposits. 2. The land must be properly located for transportation purposes close to the market in order to sell the aggregate at a minimum cost. 3. The land must be zoned so that it will be permissible to mine.

Jan 1, 1967

By E. Spyridonos

Sustainable development in the mineral industry requires a paradigm shift from purely economic to multi-objective decision-making, considering economic, social, environmental and governance criteria. The commonly accepted aim is responsible stewardship of non-renewable resources. State-of-the-art 3D geological and mine modeling software technology can contribute to meet this objective as reliable and accurate geological models form the basis for an optimum management. The benefits obtained by the application of computerized modeling are illustrated at hand of three studies. The examples cover global and local producers of industrial minerals in fully developed as well as development countries. They refer to different levels of planning, from initial resource assessment over long-term planning to the generation of rolling forecast for operative planning in a running mine.

Jan 1, 2003

By Nora M. Hutt, Kevin A. Morin

The Sobek humidity cell has been in use with minor modification for more than 30 years to determine bulk primary-mineral reaction rates. As a result, it has become a key tool for predicting the bulk rate of sulphide oxidation, the Carbonate Mole Ratio (CMR) of neutralization-potential (NP) consumption to sulphide oxidation, and the rates of metal leaching. Most humidity cells are operated for less than a year, with the resulting rates extrapolated into the future for years or decades. The validity of these extrapolations was tested by examining longer trends from cells that have operated for three to seven years, as found in the International Kinetic Database (IKD). Additionally, large batches of cells for two minesites in the IKD (45 and 46 cells each) were examined to determine if regular, predictable trends were obtained across ranges of geochemistry at a minesite. The long-term cells show that the rates of sulphide oxidation and acid generation, based on sulphate production, have a 50% chance of stabilizing within one year, with the remainder fluctuating significantly throughout their test periods. Despite the fluctuations, the CMR, which is critical for defining site-specific or rock-unit-specific ABA criteria, remains relatively steady in many cases between 1.0 and 2.0 as expected from principles of aqueous geochemistry. However, if the sulphate-production rate falls below 10-30 mg/kg/wk, the CMR value can increase significantly. At and below these low rates, physical factors like flow rates of surface waters and groundwaters will determine the rate of NP consumption, rather than geochemical factors. Also, if weekly rinse pH falls to acidic values, the CMR will decrease below 1 .O, reflecting the exhaustion of fast- neutralizing minerals. The two batches of multiple cells also confirm these trends across arange of geochemistry. The long-term cells show that copper leaching often stabilizes within a narrow range as long as rinse pH remains relatively constant. Also, there is no strong dependence of leaching on the sulphate rate. However, the rate of copper production often increases sharply if rinse pH falls to acidic values. This suggests the measured copper-production rate in some cases is not a true primary rate, but a lower secondary rate after secondary- mineral precipitation within Sobek cells. As with the long-term cells, the batches of multiple cells show that copper production often increases gradually with decreasing rinse pH, with no clear dependence on sulphate production. However, high rates can also occur at near-neutral pH, so secondary-mineral precipitation of copper is not necessarily common.

Jan 1, 2000

By S. C. Bandis, N. Barton

During drilling of deep boreholes, local mechanical failures of the wellbore walls may occur due to the inability of the incompetent overburden and reservoir rocks to withstand drilling-induced changes of the stress environment. At present, borehole failure mechanisms in three-dimensional stress fields are poorly understood. Our experimental investigations based on 3-D physical models demonstrate the stabilizing effect of the intermediate principal stress. The latter may play a dominant role in maintaining the integrity of the stress relieving failure zone around the borehole. However, this will depend on the stress anisotropy, the angle of hole deviation and on the angle of internal friction. Our tests also indicate that the failure zone can accomodate high extensional strains. Finally, relations between the physical models and closed-form elasto-plastic solutions are discussed.

Jan 1, 1986

By R. A. Bergman, P. G. Thornhill

Development of the Falconbridge Ferronickel Process for treatment of lateritic nickel ores began with laboratory work in 1955, the year the Company commenced exploration of its concession in the Dominican Republic. Process development centred on selective reduction originally directed to producing calcines amenable to ammonia leaching, but later found suited to electric smelting. The reduction step of the process was developed in a 25 tpd shaft furnace pilot plant located in the Dominican Republic, to which was later added an electric melting furnace. After almost 3 years of development work on this scale the plant was expanded to 100 tpd for fixing design data for a commercial plant. This took the form of the 30,000 ton per year Nickel Ferro-nickel Complex of Falconbridge Dominicans, which started up in 1971.

Jan 1, 1979

By Wan-Kyu Choi, Arpad E. Torma

The electrochemical reactions involved in a zinc sulfide flotation concentrate leaching with sulfuric acid in presence and absence of Thiobacillus ferrooxidans, as well as with ferric chloride - hydrochloric acid containing media, have been investigated. The cyclic voltammetric measurements revealed that many intermediate electrochemical reactions are involved in the zinc sulfide leaching. Using chronoamperometric and chronopotentiometric techniques, it was found that the leaching process is controlled by solid - state diffusion. The activation energy of solid - state diffusion process was determined by the Price's approach to be 21.3 kJ. The leaching mechanism is discussed in terms of solid - state properties (energy bondings) of the high energy gap solid zinc sulfide semiconductor and energy density states of redox systems of acidic leach media. A generalized model for the mechanism of zinc sulfide oxidation is present.

Jan 1, 1990

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By D. X. Tang, G. Wilson, Y. Luo, S. S. Peng

Knowing the location of voids/fractures in roof rock will be greatly helpful for roof support design. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way for determining void location in roof rock. In this research, feed pressure and rotation torque are found to be good indicators for identifying the voids, based on the results of a series of laboratory experiments. A set of computational rules has been developed to locate voids in mine roof using the measured roof drilling parameters and implemented in MRGIS, a software package developed to allow mine engineers to make use of the large amount of roof drilling parameters for predicting roof geology properties automatically. Anew feature, 2D map+3D figure display, is also added to MRGIS.

Jan 1, 2004

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

By James Warren Andrews

The values of saturated water vapor pressure from steam tables have been found to be inaccurate for mine ventilation usage because the effect of air on the saturated water vapor was disregarded. Presented here are the newest and most accurate currently available tables from the National Bureau of Standards (NBS). Also included are: (1) a formula for correcting the saturated water vapor pressure for temperature and altitude. (2) a formula for computing unsaturated water vapor pressure, and (3) a formula for air density. Because Systeme International (SI) units are used in the formulas, conversions are given from U. S. conventional units to SI units. The intent of this paper is to show by means of six steps the accurate calculation of mine air density for use on modern computers.

Jan 1, 1989

By Hassan El-Shall, Abbas A. Zaman, Brij M. Moudgil

The addition of organic and inorganic dispersants to aqueous suspensions of heterogeneous particles (kaolin) was found to significantly affect the solubility of metal ions from kaolin particles and stability of the dispersion. In most of the industrial applications of kaolin, highly concentrated slurries of controlled stability and fluidity are required. The solubility of kaolin particles in terms of aluminum and silicon ions and its effect on the stability of the slurry was investigated. The main objectives of this study were (1) to study the effect of the extracted metals on the properties and performance of the slurry, (2) to understand the reaction mechanism of dissolution of metals from kaolin, and (3) to understand the interaction mechanism of dispersants with kaolin particles. The controlling variables were dispersant dosage, slurry pH, solids loading, and aging.

Jan 1, 2003

By C. R. Kuhn

From 1968 to 1975, most work in surface modification of inorganic materials involved silane coupling agents. A silane coupling agent can be described simply as an oganosilicon chemical having a general formula RSi-X3 wherein the R group is attached to a silicon in a thermally and hydrolytically stable manner, and X is a hydrolyzable group usually having an alkoxy functionality. About 1975, Kenrich Petrochemicals brought into the market place titanate coupling agents. Titanate coupling agents usually consist of one alkoxy group and three functional groups attached to a central titanium atom. Zircoaluminates became available in about 1982. Zircoaluminate organometallic coupling agents, which vary principally in their respective organofunctionalities, arise from a basic technology in which two different types of organic ligands are selectively bound to a low-molecular weight zircoaluminate backbone.

Jan 1, 1995

By R. J. Matetic, Peter G. Kovalchik, Jeffrey Shawn Peterson

The National Institute for Occupational Safety and Health (NIOSH) has initiated a study of a roof bolter to reduce noise exposure to mine roof bolter operators. An important segment of this research entails determining the affect of various drilling configurations on the performance (penetration rate) and sound power emissions when drilling into granite. Test conditions included various combinations of rotational speeds and thrusts; hex and round drill steels of one inch (1.) and one and three-eighths inch (1 3/8.) diameters; vacuum and wet conditions; and using drill media of differing compressive strengths. This paper will detail the affects of each of these on the performance and sound power level emission. When drilling into granite, it was found that wet drilling generated lower sound power levels and performed better than vacuum drilling.

Jan 1, 2005

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Limited contracted to sink a 1500 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.5 ft) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (15 ft.) diameter double-drum hoist to sink the shaft with 12.5 tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1991