Search Documents

By Frank E. Dalton, Forrest C. Neil

INTRODUCTION The Tunnel and Reservoir Plan (TARP) (Figure 1) was adopted in 1972 as the most cost-effective way to bring Chicago area waterways up to Federal and State water quality standards. TARP will significantly reduce pollution of these waterways and provide flood relief for Chicago and 53 adjacent suburban communities. These communities, covering an area of 971 sq km (375 sq miles), are at present served by combined sewers, which carry both raw sewage and stormwater. Because porous ground surfaces have been covered over in recent years by buildings, streets, and parking lots, stormwater runoff into sewers frequently exceeds the capacity of the sewers. When this happens, sewers back-up into hundreds of thousands of basements, and the overflows on the combined sewers discharge rainwater mixed with raw sewage directly into the area's waterways at 645 overflow points. The result is severe pollution of the waterways and flooding in 53 communities. During particularly heavy rains, overloaded rivers have to be relieved by opening the locks and allowing the polluted waterways to flow into Lake Michigan, the region's water source. Goals of TARP 1. PREVENT BACKFLOWS INTO LAKE MICHIGAN. 2. ELIMINATE WATERWAY POLLUTION CAUSED BY COMBINED SEWER OVERFLOWS. 3. PROVIDE AN OUTLET FOR FLOOD WATERS.

Jan 1, 1981

By Lance Rasband, Richard Hanke, John Starcevich

"The world’s largest tunnel boring machine (TBM), at the time of her launch in 2012, the TBM locally referred to as “Bertha,” is incapacitated due to mechanical failure. Bertha’s stoppage places her 25m below the surface between the aged Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to access all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Due to the limited area above the tunnel alignment and physical constraints created by existing infrastructure, the dimensions of the otherwise symmetrical shaft are heavily impacted, thereby requiring special attention to design and layout. Consequently, the shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude. INTRODUCTION Mining on Seattle’s SR99 tunnel began in July of 2013. Initial mining progressed slowly through a 4.5 m thick fiber-reinforced concrete headwall before immediately entering the first of three planned safe havens. Once through the headwall and safe haven the machine would move through roughly 122 lineal meters of jet grout improved soil at a rate of slightly over 1.6 m per day. It was anticipated that once mining has passed through the improved area, “Bertha” – now the world’s 2nd largest tunnel boring machine (TBM), would be moving at a rate of almost 11 m per day. By the end of October 2013, Bertha had mined roughly 131 m, averaging 1.4 m per day, and had begun mining within native soils. By the start of December 2013, tunneling had reached the 244 m mark and Bertha was now averaging 3.6 m per day, achieving as much as 12.8 m of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt. Initial reports stated an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure within the ground around the TBM, to allow the contractor’s personnel to inspect the cutter head from within and also to investigate for the presence of obstructions at the face of the cutter head. During inspection, the contractor’s crews found fragments of steel pipe entangled in the cutter head. The steel was apparently from an abandoned 254 mm diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, she attempted to move forward but was only able to generate a slow crawl."

Jan 1, 2016

By Michael E. Salovich

The U. S. Department of Interior, Bureau of Mines (Bureau) has developed a prototype version of a computer application that combines hydrologic analysis with object-oriented graphics. This software is unique in that it presents analytic element analysis within an object-oriented CAD environment. Its user interface employs mouse handling, scrolling windows, dialog boxes, palettes, and pulldown menus. It can import scanned images of maps and overlay these images within the same window. This application was developed using object-oriented programming techniques. Several programming issues concerning graphics had to be resolved during development of this system. These include (1) how to represent hydrologic elements as graphical objects, (2) how to translate screen coordinates to map coordinates, (3) how to implement ?zooming? (changing the magnification level of a window), (4) how to overlay layers of images, and (5) how to import scanned images of maps. An object library was used to implement graphical user interface features such as scrolling windows and pull-down menus. Algorithms for CAD features such as map coordinate translation, zooming, and the layering of images were developed by Bureau researchers. The application has a modular source code structure and can be modified for use in other research applications.

Jan 1, 1992

By Gail L. Achterman

Most mining companies today perform site assessments and operational or compliance audits regularly. The purpose of these audits is to review company facilities and operations to determine whether they comply with applicable federal, state and local environmental laws and regulations. Why Audit? Companies adopt assessment and audit programs for legal and business reasons. The business reasons include: (1) ensuring efficient and cost-effective compliance through early problem identification and resolution; (2) planning and implementing business transactions such as real estate conveyances, loans, mergers and acquisitions, and waste disposal service contracts; and (3) employee training and relations. Legal reasons for audits include: (1) avoiding enforcement actions and penalties; (2) meeting environmental permit certification requirements; (3) avoiding corporate officer liability; and (4) meeting Security and Exchange Commission disclosure requirements. The Environmental Protection Agency ("EPA") encourages environmental auditing by regulated entities. The EPA Environmental Auditing Policy Statement was published in the Federal Register on July 9, 1986 (51 Fed Reg 25,004). Although the existence of an auditing program does not create a defense to or otherwise limit a company's regulatory responsibilities, EPA considers compliance programs in setting inspection and enforcement priorities. If a company makes an honest effort to identify and correct its own problems, EPA's enforcement approach is influenced, especially if violations are promptly reported. Perhaps more significant to many executives, the U.S. Department of Justice issued guidelines last year on when it will pursue criminal prosecution for environmental violations. See Department of Justice, "Factors and Decisions on Criminal Prosecutions for Environmental Violations in the Context of Significant Voluntary Compliance or Disclosure Efforts by the Violator," (July 1, 1991). It is now commonplace to read about major companies pleading guilty to criminal violations and paying millions of dollars in penalties. For example ALCOA recently agreed to pay criminal fines and civil penalties totaling $7.5 million for unauthorized excavation of PCB-contaminated soil and improper dumping of spent caustic solution. No executive wants to explain to the Board of Directors or shareholders why the company was criminally indicted. The Department of Justice considers factors such as voluntary disclosure, preventive measures and compliance programs, such as a regular compliance auditing program, the effectiveness of the disciplinary system for employees who violate the company's environmental policies, and subsequent compliance efforts by companies to remedy ongoing noncompliance. The Department of Justice looks closely at whether audit recommendations were implemented in a timely way and whether environmental compliance was a standard by which employees were judged. The Lawyer's Role. The role of the lawyer in an audit team deserves special attention. When enforcement action or litigation has begun or is contemplated or a government agency has asked for information, attorneys always should be directly involved in environmental audits. In most situations, however, environmental audits are management tools, and the attorney's role should be to advise the team. The attorney can help make sure the team understands the laws and regulations the facility must

Jan 1, 1992

By C. K. Lee

The influence of passageway fires on ventilation flows was investigated in three horizontal fire tunnel s: 1. a laboratory-scale fire tunnel network, 2. a small-scale fire-plume tunnel, and 3. a large- scale simulated mine gallery. Wood was used in the first and third tunnel and gas-burners were used in the second one to generate passageway fires. Experimental measurements included gas mass flow rate, velocity, temperature and pressure in the passageways and exhaust fans. The overall and local effects of the fires were investigated by comparing these measurements obtained before and during the fires. Results show that a passageway fire essentially increases the flow resistances of the passageways of a tunnel flow network by virtue of volatile fuel mass injection and high combustion temperatures. The ventilation air flow rate is consequently throttled to lower values than that before the fire. At severe throttling, reverse flow occurs. Conditions for reverse flow are characterized by two Froude numbers based on gas velocity and density upstream of the fire, and height of the passageway. The Froude numbers and the characteristics of the passageway fire are necessary to analyze mine ventilation/fire interaction and to predict mine ventilation patterns during fires.

Jan 1, 1980

By Frank E. Kottlowski

Widespread high-calcium (HC) limestones in New Mexico and adjoining areas, are low in magnesium, but some units include shale interbeds that would be deleterious for usage in sulfur removal. In southwest New Mexico, southeast Arizona, and adjoining parts of Mexico, limestones in the thick Mississippian Escabrosa, Pennsylvanian-Permian Horquilla, and Cretaceous U-Bar units are HC as are strata in the Mississippian Lake Valley, Pennsylvanian formations, Permian Hueco, and parts of the Permian Capitan Limestone of south-central and southeast New Mexico and west Texas. In north-central and central New Mexico, many limestones in the Pennsylvanian Madera Formation are HC as are some of the Cenozoic travertines. In northwest New Mexico, where the present-day mine-mouth coal- fired power plants occur, there are no HC limestones, but to the north in southwest Colorado some beds of the Mississippian Leadville Limestone and Pennsylvanian Hermosa Formations are HC. HC limestones considered contain at least 95 percent calcium carbonate and less than 3 to 5 percent magnesium carbonate. Limits for other impurities are alumina, 1 percent; silica, 2 percent; sulfur 0.05 percent; phosphorous, 0.02 percent; and iron oxide, about 1 percent. Chemical and physical requirements differ slightly depending upon the ultimate use.

Jan 1, 1995

By P Moser

Within the EU-research project "Blasting Control", jointly operated with partners from France, Italy and Greece, between 1992 and 1995, the Department of Mining Engineering of the Montanuniversity Leoben, Austria took over the task to develop a diagnosis system applicable in underground drifting, in order to identify possible reasons for blast failures or poor blast performance. For that purpose 120 m of 12 m2 test galleries were excavated at two different mine sites. For every blast performed the collar and bottom position of every hole drilled, the charged hole length and the drift and face profile of the round blasted were monitored. These 'geometrical" data were put directly from the measuring devices into SURPAC, the mine planning software chosen for data analysis. Based on the data computed, 3D plots comparing actual and planned data were made visible on the screen or as hard copies. Experience from the introduction of this system into a mining operation showed, that the system developed contributes to an improved understanding of the reasons for blast failures and forms the basis for an improved blast design. The soft- ware package SURPAC was also used to train the miners directly at the mine site in order to improve the quality of their work.

Jan 1, 1996

By O. J. R. Baena, D. E. Chaverra, C. D. L. Ramirez

Cyanide is one of the most used reagents in the precious metal extraction process; as well as the most efficient from the point of view of the dissolution process; but it is also a toxic product that requires a lot of care in handling. Likewise, the residual solutions of the process must be followed because they can be a risk of contamination of water, animals and human health. In the artisanal processes of obtaining gold and silver, neutralization of the residual solutions is used to passivate the present cyanide. During this process ammonium cyanate is formed which decomposes rapidly in the presence of air and sunlight in carbon dioxide and ammonia gas, contributing to the greenhouse effect. In this work the use of the ammonium cyanate obtained in the process of neutralization of the cyanide solutions as a reagent to obtain urea is proposed. Urea was obtained indirectly through the use of the reagent kit UREA/BUN-COLOR. The process is effective at pH ≤ 4.5 with a rapid increase in solution temperature, and addition of hydrogen peroxide. The urea crystals begin to form at 50°C. The cyanide / urea ratio obtained was 1 / 7.5 INTRODUCTION In the processes of extractive gold metallurgy, the use of cyanide leaching is perhaps the most widely used method worldwide; by the ease of operation, its low cost and high levels of precious metal recovery. However, neutralization, in most processing plants, is not done properly, and leftovers of solution with free cyanide are dumped in concentrations harmful to the environment, in particular animals and humans. Cyanide can enter surface water through releases from industries using cyanides. Due to its high toxicity, the presence of cyanide in water is a matter of great concern (Jawale et al., 2017). The pollution generated by the effluents from the leaching of gold ores is one of the main obstacles of social opposition presented by mining activity due to the impact of both surface and groundwater. During the cyanide decomposition process, a compound known as ammonium cyanate OCN(NH4), which is a raw material for the manufacture of urea, CO(NH2)2 is generated. In the case of good neutralization, cyanide is no longer a toxic compound through oxidizing reagents, but as a result, there is the generation and emission of ammonia and carbon dioxide into the atmosphere, generating both a greenhouse effect (Gómez, 2012). This is evidenced by the strong effervescence of the reaction, and a penetrating smell of ammonia, which can irritate respiratory mucous membranes and eyes; however because they are greenhouse gases they are considered pollutants.

Jan 1, 2019

By J. Fox, C. Allen, A. Greth, K. Kocsis

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water, and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contribute a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed. The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than of the diesel engines. Battery powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers, and (c) reduced mine operating costs due to lower ventilation requirements. This paper will highlight the health and cost benefits of using battery/electric fleets versus diesel fleets in deep and hot underground mines. The study analyzes simulations produced from thermodynamic ventilation models. Early simulations show significant cost reductions in terms of net present value (NPV) when comparing the air volume requirements for battery/electric equipment versus diesel powered equipment for the same production rate. INTRODUCTION The competitiveness of the world mineral market demands that mine operators continue to increase production and decrease costs as commodity prices fluctuate in often unplanned directions. This has forced underground mines to operate at deeper depths and to become more mechanized to remain competitive. Because of these changes, ventilation challenges have continued to increase as the mines combat an enlarged influx of contaminants such as heat and diesel particulate matter (DPM)."

Jan 1, 2018

By William M. PhD. Schafer

The net acid generation (NAG) pH method is an important analytical tool that supplements static and kinetic tests for assessment of the acid generation risk of rock samples. This method is useful because it is simple, rapid and cost-effective; it combines features of the static and kinetic tests; and it can be conducted at mine assay labs. The NAG pH test is particularly effective for operational testing programs used to classify, selectively handle, and route potentially acid-generating waste rock. The NAG pH procedure is based on a 24 hour oxidation of a pulverized rock sample with hydrogen peroxide and subsequent measurement of the sample's pH. If the NAG pH is below a critical value, determined empirically, then the sample has the potential to generate acid in the field. The critical NAG pH value is typically within the range of 3 to 4.5, but the exact relationship between NAG pH and potential acid generation should be determined individually for each mine site, based on comparison with results of acid base accounting, humidity cell tests, and mineralogical analyses. Calibration and use of the NAG test for predicting ARD risk at several mines are described in this paper.

Jan 1, 2000

By Paul Sainato, J. Steven Gardner

Sustainable development is defined as ‘development that meets the needs of the present without compromising the ability of future generations to meet their own needs.’1 There has been considerable debate of late between environmentalists and mining operators concerning the current regulation and operation of mountaintop mining. To those not familiar with the practice, it essentially applies an area mining method to a mountaintop, removing all overburden above coal seams, resulting in full recovery of the resource with the excess or swell spoil material - (rock and dirt) being deposited in engineered fills in hollows to the side (known as hollow fills or valley fills - very similar to highway fills). Because most of the dialogue has been adversarial and mining’s response is perceived to be primarily reactive instead of proactive, a rift in communication and value systems between the two sides has widened. Since 1999, the global mining community has been concerned that there is a disconnect between mining practices and the values of today’s society.3 Working through the World Business Council for Sustainable Development (WBCSD), the International Institute for Environment and Development (IIED) was created to review mining practices in a project entitled Mining, Minerals and Sustainable Development (MMSD) driven by the following four goals:

Jan 1, 2005

By Dinah O. Shumway

California's annual production of >11 million tons of cement, at a value of over $640 million, comes from eight companies, which operate 11 plants. Cement is California's second most important mineral commodity, representing 25% of its total annual mineral production. Although most of the cement produced is consumed within the state, current export locales include the Pacific Northwest, Nevada, Arizona, Utah, and New Mexico. An enumeration of the components required to produce cement is deceptively simple: calcium oxide (65%), silica (20%), alumina (4-5%), iron (3-4%), and calcium sulfate (4%) as a retardant admixture. The last, and most expensive, ingredient in cement manufacture is energy. Detrimental materials in cement mixes include excess .magnesium, alkalis, heavy metals, sulfur, and other volatiles. Each of the 11 cement plants in California requires a unique chemical solution of combined raw materials to produce a uniform product: portland cement. The geologist proposing solutions for the additive raw materials in cement manufacture must have a thorough knowledge of a particular cement plant's needs. In the California cement market, keeping the costs of additive raw materials down is one way to also stay competitive, and using a combination of natural and waste materials as additive raw materials allows cement producers to stay competitive.

Jan 1, 1999

By R. J. Nankee

Recent on-going efforts to develop commercial coal cleaning beneficiation processes using chlorinated solvents-as the separating media will be described. True heavy media separations were performed on raw coal feedstocks, including Pennsylvania anthracite; Western, Eastern, and Midwestern bituminous; and lignite coals. Separation techniques included bath-type devices, cyclones, and liquid/liquid partitioning. Details on separation devices, removal of solvent, and recovery and recycling of solvent will be discussed. Projected costs of full-scale plants will be given for various coal sizes. A number of the coals evaluated are good candidates for beneficiation using chlorinated solvents. Coal beneficiation is desirable to provide needed coal quality. These needs include low ash fuels for coal water slurries and low sulfur fuels to meet emission regulations. In October of 1985, a paper, "Chlorinated Solvents for Coal Beneficiating"' was presented at the fall meeting of SME-AIME at Albuquerque, New Mexico. It reported the results obtained from various coals as feedstocks and of the separations using chlorinated solvents. These beneficiation results depended on true heavy media gravity and liquid/liquid partitioning separations. This paper will include detailed descriptions of the liquid/liquid partitioning process used in "Dow's Advanced Coal Cleaning Technology?2 and of the "Dow Solvent Recovery Technology.?3

Jan 1, 1987

By Walker Ian W., John D. Gow

The paper describes the exploration and development activity associated with a series of open pit gold deposits in the Laverton region of Western Australia with an aggregate resource base of 4 million tonnes at a grade of about 3 grammes per tonne. In September 1988, Hill Minerals N.L., now a wholly owned subsidiary of Ashton Mining Limited, completed the purchase of the Cork Tree Well treatment plant from Austwhim. This CIP plant had a rated capacity of 235,000 tonnes per annum, and is located within the Hill Minerals Laverton Project area. Ore is trucked by haulage contractors from each open pit mine to the central treatment plant at Cork Tree Well. Studies were completed and a plant expansion undertaken lifting throughput to 500,000 tonnes per annum. A contract was let for this expansion in November 1988, and construction completed in April 1989. Concurrent with the above project development work, heap leach metallurgical studies are being undertaken on low grade mineralisation associated with higher grade ore zones at several of the open pit mines, notably King of Creation and Craiggiemore. It is anticipated that heap leaching will provide a useful adjunct to gold production from milling higher grade ores.

Jan 1, 1989

By C. J. Newman

Prior to 1995, the smelting process at the Kennecott Utah Copper Corporation (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. In the consideration of expansion opportunities, the existing process did not lend itself to a program geared towards processing the total output of KUCC mining and milling operations. During 1989 and 1990, a number of smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1.0 million tonnes per year of copper concentrate, with the ability to expand to 1.2 million tonnes per year. Following the shutdown of the smelter facility utilizing the Noranda technology in May 1995, the flash smelting furnace commenced operation in June with the flash converting furnace startup following a few weeks later. The smelter has achieved design production targets and environmental goals. Current operating rates are at or above design rates for concentrate and matte processing. Emissions are lower than the permit levels and equate to less than 3.5 kg of S02 per tonne of copper. This paper outlines the design, construction, startup and the first two years of operation of the modernized KUCC smelter.

Jan 1, 1998

By Yuting Xue, Khaled Mohamed

The failure of coal ribs is a major hazard in underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have been working on the development of an engineering-based rib control method. A user-friendly standalone application, called Design of Rib Support (DORS), is being developed to ease the calculations of rib support. DORS can estimate the Primary Rib Support Density (PRSD, ton/ft2) for development loading. However, it still needs to take account of another key factor, bolt length, in rib support design. The bolt length can be estimated from the rib fracture depth, and this study focuses on the coal rib fracture depth analysis with numerical modeling and artificial neural network. A total of 331 FLAC3D simulations with different mining scenarios and rib conditions were conducted for this study. Machine learning was then used to predict coal rib fracture depth under different conditions. Based on the numerical simulations, the parameters for mining scenarios and rib conditions were collected as features for machine learning, and coal rib fracture depths were collected as the target to predict. Good data correlation (r-square) was obtained with the use of an artificial neural network. The

By J. A. Organiscak

Data on dust-control practices, mining conditions and occupational exposures were gathered for approximately 80 underground continuous mining units. Despite silica contents on dust samples in excess of 5%, nearly forty units successfully maintained silica concentrations at or below 100 µg/m3 on a majority of occupational dust samples, while the remainder had difficulty maintaining this level. These two sample sets were termed Group A operations and Group B operations, respectively. This data was compared to identify causes of high occupational silica dust exposures. Analyses of dust-control parameters and geologies revealed only minor differences between these two groups. However, subsequent comparisons of face ventilation design showed considerable differences in silica exposure and silica content between Group A and Group B at the continuous mining machine and roof bolter operator occupations. These differences were minimal when using exhaust curtain ventilation with a dust scrubber. This face ventilation system can benefit operations having difficulty controlling silica dust exposure and silica dust content. The collected data also showed that occupational samples from Group B operations possessed generally higher silica exposures and silica content than similar samples from Group A. The single head roof bolter (helper) possessed among the highest silica exposures and silica contents in both groups.

Jan 1, 2002

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By M. K. Gangal, E. D. Dainty

The paper describes the use of portable aerosol monitors in determining real-time concentrations of diesel soot and respirable total dust in dieselized mines. The field studies were conducted in a simulated diesel environment in the laboratory where no other type of dust was present, and in four underground mines with multi-diesel machine operations. Two packages for the real-time monitoring of diesel soot were prepared which included two types of aerosol monitors: a Miniram, model PDM-3, and a Sibata, model PDS-1. These monitors utilize the principle of light-scattering to measure the airborne mass concentration in the environment. The monitoring device results were compared against the Time-Weighted-Average (TWA) values produced by the gravimetric filter sampling method, permitting calibration factors to be determined for each field test. Both instrument packages provided comparable results. The instrument calibration factors varied for different tests, which may be due to different material composition, particle size distribution, density and shape of the aerosols. This approach for real-time determination of diesel soot is found to be simple, inexpensive and easy to use. More field tests for diesel soot determination and further research on size distribution of particulates in dieselized mines are required.

Jan 1, 1989

By Ahmet Unal

Inexpensive and effective means of delivering courses to mining engineers who live at remote and scattered locations remains to be a challenging issue. Computer-based instructorless but interactive multimedia delivery is a good substitute to traditional short courses and one-way broadcasts. Such a system, enhanced with a wide area network, is an inexpensive alternative to two-way broadcasts and even to a traditional university. Course material can either be delivered on compact disks (CDs) or on-line from the host servers over the phone lines using a personal computer and a modem. Although technically not feasible using ordinary telephone service lines at the present time without further modification, advances in this field indicate that this up and coming medium may dominate the competition in the future. This paper investigates the present and the future of this technology and discusses the experiences gained in creating and disseminating a prototype multimedia CD which was created at the Rock Mechanics and Explosives Research Institute of the University of Missouri-Rolla to teach a portion of a course in Ground Control. The hardware and software used in creating the audio, 3-0 graphics, animation dips, video clips, and movies are listed. The structure of the program and the way how interactivity was achieved is explained in detail.

Jan 1, 1996