Search Documents

By Andrew J. Gaber

Beginning in 1961 the Coal Research Bureau of the West Virginia University School of Mines began a program of research to investigate the potential of the magnetic separation process to remove sulfur of the pyritic form from pulverized coal. Using a so-called isodynamic magnetic separator (1) it was demonstrated that significant quantities of pyritic sulfur could be removed from coal. Pulverized coal samples representing several different coal seams were individually screened into sizes in the 48 mesh by 200 mesh (297 to 74 microns) range, and untreated and steam-air treated samples of each were processed by the magnetic separator. The results of the investigations to magnetically remove pyrite from coal were published in two separate reports issued by the Coal Research Bureau (2,3), The isodynamic magnetic separator was designed about 30 years ago for use in geological and mineralogical laboratories (1,4,5) to isolate one or more minerals exhibiting only small differences in their magnetic propertiese Specifically, to accomplish this, the air gap of the unit was designed to provide a nearly constant magnetic gradient both laterally and longitudinally in the separating zone. It is reported that mineral concentrates of 99.5 percent purity can-be produced on closely-sized fractions after several cleanings through the unit. The isodynamic magnetic separator, therefore, was not expected to process coal containing sizes smaller than 200 mesh, or to demonstrate commercial capability to process pulverized coal. The primary purpose of the Coal Research Bureau in using the unit was that of determining if the magnetic process could remove pyrite from coal, and thereby encourage further research directed toward development of acceptable full-scale processing equipment.

Jan 1, 1969

By Joe D. Mitzel

The Indian Head fine has been in existence since 1922. For over 56 years there have been North Dakota people mining coal at this same location. The area affected will fit inside a circle 5 km in diameter, and the coal is lignite. The seam thickness has varied from 2.4 m to 3.65m, and the overburden from 6 m to 30 m in depth. me Lignite coal which is being mined at the Indian Head Mine is from 15.8 x l0 6 to 16.7 x 10 6 J per kg; it has a moisture content of 33 to 38%; an ash content of 5 to 10%; and a sulfur content of from 0.5 to 0.7%. The moisture content and the fact that we crush the coal co a top size of 14 cm x 0, are two of the characteristics or the product which cause it to freeze and remain inside of the railroad cars on the slope sheets. The market for the coal initially was almost entirely local coal sales. That is, coal was sold to people in the area who used the lignite to heat their homes, stores, offices, schools, and churches. Back in the early 1920's, there were no stoker-fed boilers, or pulverized fuel boilers, as we have in today?s marketplace. Basically, all of the coal was sold as lump coal, pieces about 30 to 35 cm square, to be used in furnaces: and nut coal with a top size of about 7.5 cm to 10 cm to be used in the old kitchen cookstove. All of the coal fines, less than 5 cm, were screened out and layed onto a pile. There was no market for the smaller sizes of the lignite coal. It has been our experience that when the coal is in lumps or chunks larger than 7.5 cm to 10 cm, there is a very slight possibility of freezing. That is the chunks themselves freeze, but by their nature, they do not cling to one another or form large masses of frozen material which are difficult to remove from the slope sheers of the railroad cars.

Jan 1, 1980

By William H. Mount

INTRODUCTION Effective mine ventilation is required to maintain a healthy underground environment for humans. Without effective ventilation, the environment can become unhealthy or hazardous as a result of the depletion of oxygen, contamination with toxic gases, or the buildup of an excessive amount of particulate matter (dust). Each contaminant has an upper limit of concentration that should not be exceeded within an 8-hr period. This is known as the threshold limit value (TLV). The TLV represents an acceptable level of exposure that should produce no ill effects. Unfortunately, more than one contaminant may be present at any one time and the effects of the individual contaminants may be additive, i.e., the effects of each contaminant must be considered simultaneously to determine the potential danger to miners. Possibly the greatest threat to mine-air quality is the uncontrolled underground use of the diesel engine. The diesel engine was invented in 1892 by Rudolf Diesel. His intention was to develop a power source that could burn coal dust as a fuel, but he was unsuccessful in that attempt and had to resort to liquid petroleum fuels (Johnson, 1975). In 1898, the diesel engine was intro¬duced into the United States by Adolphus Busch, who anticipated using it as a prime mover in factories and generating plants. At that time, the diesel engine was a very large and very heavy engine, designed for fixed installations. By 1919, lighter engines were being developed, and by 1931, Caterpillar was marketing a diesel-powered, track-type tractor (Henderson, 1975). Since 1931, the diesel engine has evolved into an extremely popular prime mover in medium and heavy-duty applications. Efficiencies now are on the order of 40% and improvements such as turbocharging and aftercooling have produced engines capable of generating power at a ratio of 0.3 kW/kg (1.0 hp per 5.0 lb) of engine weight. Although the diesel engine is relatively efficient as a mobile power plant, it is far from efficient in terms of the energy produced from the energy potential of the fuel. About 60% of the heat value of the fuel leaves the engine as wasted heat, with about 50% of that heat being emitted through the exhaust pipe and the other 50% being emitted through the radiator or cooling fins. Perfect combustion in an engine would produce only water vapor (H_0), carbon dioxide (CO_), and nitro¬gen (N2) as the byproducts. Since the diesel is not a perfect engine, each pound of fuel burned generates 5.6 m° (200 cu ft) of exhaust gas, containing about 0.009 m3 (0.33 cu ft) of carbon monoxide (CO), 0.009 m' (0.33 cu ft) of nitrogen oxides (NO, NO2, and NOD), and 0.57 m3 (20 cu ft) of carbon dioxide. The balance of the exhaust emission consists of free nitrogen and water vapor (Hurn, 1975). Contrary to popular belief, the diesel is not inherently dirty. Under normal operating conditions, a well-maintained engine neither smokes nor smells. However, the same well-maintained engine can and does produce toxic emissions. A diesel engine is not inherently safe and constitutes a distinct hazard to personnel. This chapter is devoted to a description of the various toxic substances that may be generated by a diesel engine. Although some of these substances may also be produced by blasting or natural causes, the focus of this chapter is on the relationship between the internal- combustion compression-ignition engine (the diesel) and the quality of the mine air. CARBON MONOXIDE Combustion Process During the combustion process (burning) of organic fuels, each atom of carbon combines with two atoms of oxygen, provided that a surplus of oxygen atoms is available. Thus, the carbon is oxidized to carbon dioxide. Most open flames, such as trash fires, camp fires, gas ranges, etc., produce carbon dioxide. However, with insufficient oxygen, incomplete combustion results as the carbon atoms each combine with one atom of oxygen to produce toxic carbon monoxide. Burning charcoal briquettes produce carbon monoxide because the combustion takes place inside the briquettes where sufficient oxygen is not available to the combustion process. Internal-combustion engines, whether burning gasoline or diesel fuel, also produce carbon monoxide. The only oxygen available to the combustion process is that trapped within the cylinder. If the amount of fuel delivered to the cylinder is excessive, there is insufficient oxygen for complete combustion and carbon monoxide production results. In a normally aspirated (nonturbocharged) diesel engine, the amount of air "sucked" into a cylinder is the same on every intake stroke, resulting in complete combustion only at low levels of engine loading, when small amounts of fuel are injected. Higher levels of engine loading cause larger amounts of fuel to be injected into the same volume of air in the cylinder. Unless the volume of air is increased, the combustion process becomes progressively less complete as the amount of fuel increases. Turbocharged engines are able to compensate some¬what for increased loading and increased fuel consumption. The turbocharger acts as a compressor for the intake air, forcing a larger volume of air into the cylinders as the engine speed increases. Hence the turbocharged engine burns cleaner than a naturally aspirated engine and produces slightly less carbon monoxide (Marshall and Fleming, 1971). Much of the underground equipment used today is powered by turbocharged indirect-injection diesel engines. Although these engines emit fewer toxic contaminants than naturally aspirated engines, they do not eliminate the problem. Since the turbocharger is driven by the exhaust gases, rapid accelerations can cause temporary overfueling of the engine until the turbocharger attains a speed sufficient to restore the correct air-to-fuel ratio. During this "turbocharger lag," the combustion cylinders contain insufficient oxygen, causing severe smoking and an increased output of carbon monoxide.

Jan 1, 1982

By Frank W. Schmechel

The subsidence monitoring program at the Old Ben No. 24 Mine was planned in 1976 as part of the on- going demonstration of longwall mining. The construction and installation of the network of surface subsidence monuments was started in Play of 1976 and completed four weeks later after which an initial reference survey was made of all surface monuments. Mining of the first longwall panel started in September of 1976 and was completed in May of 1977. Mining of the second panel started in August of 1977 and is continuing at this time. The Automatic Data Acquisition System (ADAS), which is the subject of this paper, was installed over the second panel on March 29, 1978 near the panel center (Figure 1) and approximately 104 meters (370 feet) in front of the face position at that time. Mine No. 24 is located approximately 5 kilometers (3 miles) Northwest of Benton, Franklin County, Illinois. Coal is being mined from the Illinois (Herrin) No. 6 seam which is at a depth of about 189 meters (620 feet) at the site. The Herrin No. 6 is up to 2.7 meters (9 feet) thick in the mine but a constant thickness of 2.1 meters (7 feet) is being mined by the demonstration longwall with both roof and floor coal being left for stability. Although the seam is flat laying at the mine, it dips north- ward regionally. Topographically, the surface over the demonstration panels is essentially flat and low laying with several areas of standing water. The Rend Lake Dam (United States Army Corps of Engineers) is about 305 meters (1000 feet) north of the demonstration site.

Jan 1, 1979

By C. D. Atkinson

The past few years have seen a much greater concern about air pollution in this country. This concern has led to increased legislation restricting the discharge of many substances such as sulfur dioxide and particulate matter to the atmosphere. In the future, it is anticipated the present permissible emission levels will be lowered. Current and impending restrictions on the emission of sulfur dioxide have brought out the fact that there is a shortage of available low-sulfur fuel for power plants and industrial use which promises to have an economic impact on the nation's energy picture (1) The Pittsburg & Midway Coal Mining Co., under the sponsorship of the Office of Coal Research, has developed a process to produce a fuel capable of meeting the energy requirements of this nation (2) The process is called "The Pittsburg & Midway Solvent Refined Coal Process". The principle product from the process is Solvent Refined Coal which is an ashless, low-sulfur fuel with 16,000 BTU per pound regardless of the rank coal from which it is produced. The product can be burned as either a solid or a liquid fuel. The process appears to be economically more attractive than other methods of alleviating the pollution problems of this nation. In addition to reducing the air pollution caused by stack gases, the product produced is potentially useful as a source of electrode coke and electrode binder pitch, as a gas turbine fuel, in the production of metallurigical coke and pavement asphalt, and as the first step in the overall process to produce distillate fuels and pipeline gas (3).

Jan 1, 1973

By G. W. Cutting

It is well known in both the research field and in commercial flotation processes that the grades and recoveries obtained from flotation plants are heavily influenced by the structure and height of the froths produced in the flotation cells. The development of steady-state mathematical models of flotation processes based upon practical and readily obtained parameters have demanded detailed information about the structure of flotation froths. The important parameters are the distribution of floating values, gangue and water in the froth with respect to froth height, cell pulp density, cell air flow rates and flotation inducing additives. Little work has been conducted in this field although considerable attention has been paid to bubble loading and other factors close to the cell froth/pulp interface. Laboratory batch tests are prefaced for the derivation of the above mentioned parameters for both practical and economic reasons. The standard laboratory flotation tests using a batch cell produces a froth of low height (1 to 3 cms generally) together with a varying cell pulp density as the test progresses due to the addition of top up water and the removal of froth from the cell. This form of test can be considered only as giving information about froth conditions close to the cell froth/pulp interface under conditions of widely varying cell pulp densities. In commercial processes the froth heights are much larger (frequently greater than 10 cms); therefore the laboratory batch test, although useful in many ways, does not directly yield parameters relating the state of the froth flowing over the cell lip to process operating conditions. To investigate flotation conditions, where more realistic froth heights are developed, an equilibrium type of batch cell has been developed at Warren Spring 1 Laboratory . In this a tank with high walls is used to contain the pulp and whole froth and, after a short period of operation, an equilibrium between froth

Jan 1, 1975

By G. C. Kachel

During the past two years, there has been an increasing acceptance of process automation among ferrous, non-ferrous and non-metallic rock processing operations in an attempt to keep total unit costs in line in a market situation where labor and material costs are rising almost daily. Previous technical papers (1) (2) (3) (4) (5) have described, in considerable detail, instrumentation and automatic control devices that have been successfully applied in a wide variety of crushing and grinding facilities. While many of the basic control philosophies that evolved almost ten years ago remain essentially unchanged, new components and devices have been developed during the past two years that permit these philosophies to be better implemented in operating plants. Some of these devices and their application will be discussed with particular emphasis placed in describing the basic control philosophy employed as well as some of the hardware or components comprising typical crushing and grinding circuit control systems. Before any instrumentation or automatic control system can be successfully devised for a specific facility, there must be a clear understanding and agreement by supplier and user as to the control system objective. In the case of a crusher feed rate control system, the objective is generally to maximize thru-put of a given finished product size. While this is often the case in a grinding circuit automatic control system, the reasons may be entirely different. Taconite processors whose end product is to be pelletized, generally attempt to control their grind within narrow limits to optimize balling action. Other milling operations are more concerned with obtaining metallurgical liberation and can, in many cases, tolerate wider swings in finished grind.

Jan 1, 1969

By G. R. Goldak

All of Canada's older uranium mining areas have been intensively prospected and known outcrops have been repeatedly examined. The only ground in these areas which has not been explored is that which is covered by water or other overburden. The discovery of new mines in these areas will, in the author's opinion, depend on the development of new geophysical or geochemical tools capable of locating uranium deposits which are-buried beneath tens to hundred of feet of overburden. Such tools would be extremely useful in Saskatchewan's Cluff Lake and Wollaston Lake areas. Uranium has recently been discovered in significant quantities in these regions but exploration is made extremely difficult and expensive by an almost uniform overburden cover. The author's experience has been confined to Canada but apparently a subsurface uranium prospecting method could be widely exployed in the western United States and Australia as well. Radon-222 measurements have been used for more than a decade on practically a worldwide basis in an attempt to obtain a useful method for subsurface uranium prospecting. It is well known that ha-222 produced by buried uranium deposits can diffuse through an overburden cover so that it can sometimes be detected at surface. An advantage of this method of prospecting is that Rn-222 can be detected with a simple scintillation, ionization or semiconductor detector. One of the essential weaknesses of the method is that the mean diffusion path length of Rn-222 is limited by its very short (3.8 days) half life. For a deeply buried deposit, vitually all of the Rn-222 atoms will decay before reaching surface and, therefore, such deposits cannot be expected to produce a detectable radon anomaly. Thus, except in unusual cases where groundwater or ground air flow assists the movement of radon towards surface, the depth of exploration is probably limited to ten or twenty feet of overburden cover. The high solubility of Rn-222 in water is also a source of difficulty. In an area where overburden covers bedrock with water saturation of the lower overburden levels, the radon will simply dissolve in the groundwater, and soil gas readings at surface will indicate falsely low

Jan 1, 1974

By David L. Daniels

The U.S. Geological Survey has for many years been flying and compiling aeromagnetic surveys. The aim is complete coverage of the United States, about half of which is presently done. Colored aeromagnetic maps at a scale of 1:1,000,000 are published as the states are completed; Minnesota and Colorado have been published. Michigan, Iowa, Nevada, Utah, Maryland and Virginia are presently being processed. Some of the most spectacular data collected to date is from the Piedmont of the Eastern United States. I am going to discuss a preliminary aeromagnetic map of the Piedmont region between New York and North Carolina, where coverage is nearly complete. This map has been compiled from many surveys. Flight spacing over Piedmont rocks is 1/4 to 1 mile with flight elevation of 500 feet above ground. The spacing over the Virginia Coastal Plain and Valley and Ridge regions is wider at 2 - 3 miles. Much of the data in Virginia has been produced by the Virginia Division of Mineral Resources. The map is colored on a spectral color scheme with red for the higher intensities and violet the low intensities. Each color represents a 100 gamma interval. Some of the highest intensities are beyond the range of the 13 colors - these are left white. It is necessary, of course, to remove first, the Earth's main magnetic field. The Geological Survey uses the International Geomagnetic Reference Field or IGRF (Fabiano and Peddie, 1969). The use of color in aeromagnetic maps is not new, but then not common. We have found that colored aeromagnetic contour maps are more useful by far than the uncolored versions because they allow the user to instantly compare intensities in widely separated areas and visualize long wavelength anomalies even when numerous short wavelength anomalies' are superimposed. One tends to see only steep gradients on uncolored aeromagnetic maps, the broad anomalies being quite invisible. We feel that colored maps take the place of various mathematically derived maps such as second derivative or averaged maps.

Jan 1, 1973

A panel discussion on carbon-in-pulp processing of gold and silver ores was one of the highlights of the 1981 AIME Annual Meeting in Chicago. The session generated considerable interest and discussion among panelists and the audience. For those unable to attend the panel, the program was recorded and the discussion appears in this two-part report. The panel was co-chaired by Robert S. Shoemaker, vice president of San Francisco Mining Associates, and Laurence D. Hartzog, principal engineer with Bechtel Civil and Minerals Inc., San Francisco, CA. Panel members included: George Potter, consultant, Tucson, AZ; Kenneth B. Hall, metallurgical superintendent, Homestake Mining Co., Lead, SD; and Donald M. Duncan, resident manager, Pinson Mining Co., Winnemucca, NV. There have been several types of carbon-in-pulp adsorption vessels in use, such as the Dorr-type agitator, the simple propeller agitated tank, the Pachuca tank, and, lately, the draft tube-type of agitated tank. Which one of these is best and why? Potter: On the selection of the most appropriate adsorption vessel, there is a considerable difference of opinion that stems largely from the fact that every ore is different. The mesh of grind, the pulp solids, and the apparent viscosity of the pulp as caused by its clay content and chemical conditions all differ. The traditional Dorr agitator with the slow speed center sweep and either peripheral or center column air lifts has worked quite well on the finer grinds of all minus 65 and probably 70-80% minus 200 mesh. Pachuca tanks have also been successful and they may be capable of handling a coarser feed than the traditional Dorr tank. One uranium mill, for example, handles minus 28 mesh sandstone ore in a Pachuca. The most recent development and one that commands consideration is the draft tube agitator in which there is a turbine which closely fits inside a draft tube. Velocity in the tube is carefully calculated to avoid undue shear and thus abrasion of the carbon. The objective in all cases, of course, is to mix the granular carbon, which is typically 6 x 16 mesh, very gently but thoroughly in a slurry with minimum carbon abrasion. I do not know that there is one outstanding choice just yet and I have been unable so far to get information on C-I-P service for ore grinds as coarse as 35 mesh. Duncan: The major advantage of draft tube-type is the ease of startup. At the Pinson plant we installed draft tube-type agitators but it is too early to quote experience with them. We also haven't operated long enough to determine just what our carbon loss is. The advantage, of course, in the draft tube design is that it requires only about one-third the horsepower input of a conventional agitator. If it has no other advantages, it has that. Hall: The type of vessel most suitable for C-I-P adsorption depends on the type of ore treated and the prevailing operating conditions. In most cases, a deep tank with turbine-type mechanical agitator and low speed tip velocities would be satisfactory. Turbine-type impellers give a positive type of agitation which assures optimum ion contact and reduces short circuiting. Thorough aeration is possible with an air sparge properly located. A mechanical agitator can easily be started up after an outage, but it is usually necessary to drain and wash out a Dorr rake-type or Pachuca before restarting. The turbine-type impeller requires more power, but maintenance costs are negligible if rubber covered impellers are used. Carbon losses are minimal. In smaller plants, Pachuca type agitators provide adequate aeration and agitation. Bob Polak, Occidental Minerals (from the floor): Mr. Hall, you favor the mechanical-type agitator with the preface that the proper design is critical. Could you elaborate on this for us? Hall: The most important thing is low tip speed to prevent carbon attrition. I think the impeller should be sized so that you get a good sweeping action toward the bottom of the tank, across its bottom, up the sides, and back to the center. The advantage of the draft tube is that you get a more positive agitation and you probably get improved aeration too. Polak: Do you know of anyone using an upflow mechanical agitator rather than a downflow unit? Hall: I think that Bob Wilson at Custom Equipment has designed one where he has located the sparge directly beneath the impeller. The air bubbles are broken up by the impeller as the slurry passes through it. The slurry flows upward, outward, down the sides, and, again, back to the center of the tank. I don't know that any tanks of this design are in commercial use. Hans Von Michaelis, Randol International (from the floor): A question to any of the panelists on flat bottom versus conical bottom Pachucas. Hall: I would say the conical bottom would be most suitable in most cases. Some plants have experienced problems with flat bottom Pachucas in that they have a tendency to sand in on the sides of the tank so only the center of the tank is active. Duncan: With our draft tube tank we placed an inverted cone in the center of the tank bottom and blanked off the bottom comer around the circumference of the tank to facilitate movement of the pulp. Other than that, as far as conical bottom tanks are concerned, I'm generally opposed to them because of the cost and height differential. Larry Kramer, Kennecott Minerals Co. (from the floor): Mr. Duncan, you mentioned that the draft tube-type could be agitated with about one-third the horse-power applied to a conventional propellor agitated tank. I have trouble trying to pin down that kind of number. Could you give a bit of rationale as to why that mechanism has a lower horsepower requirement? Duncan: I think it has to do with the fact that below the propeller you have straightening vanes. The pulp, which is flowing vertically downward, is turned and flows upward again without any recirculation. You have an inherently less horse-power requirement in that type of tank. The one-third horsepower requirement is a number I obtained from Lightnin, which supplied us with details of the draft tube. There is probably much more recirculation with a conventional impeller type that is wasted motion. Potter: Last week I saw some agitators in South Africa with short draft tubes and actual turbine-type impellers. This plant was handling 200 kt of ore per month. The tanks were flat bottomed, and the agitation appeared to be quite satisfactory.

Jan 8, 1981

By G. Robert Moorehead, Peter T. Luckie, Harold L. Lovell, David J. Akers, James K. Kindig

Jigging is a process of particle stratification in which the particle re- arrangement results from an alternate expansion and compaction of a bed of particles by pulsating fluid flow. The vertical direction of fluid flow is reversed periodically. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. This response, developed from the many and continuously varying forces acting upon the particles, permits a solid-solid separation more related to particle density and less to particle size than any other "hydraulic-type" process. The stratification is usually carried out in a rectangular, open-top container called a jig, in which the mass of particles (termed a "bed") is supported on a perforated base through which the water flows in alternating directions. The coal particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen. Following the particle stratification, the particle bed is physically "cut" at a desired horizontal particle density plane to separate the desired clean coal product from the more dense refuse. The jig system includes means for continuously introducing the raw coal and for moving the water through the coal bed in a controllable manner, as well as for separating and removing the stratified particles from the system as two or more product streams. In coal preparation, this highly versatile unit operation is applied preferably to a wide size range of particles with top sizes up to 8 in. (20 cm) rather than to a closely sized fraction. In gravity ranges, the process has been applied to gold particles with a density of 19.3 and to coal particles having densities less than 1.30. Single jig washers have capacities from 5 (4.6) to greater than 700 tph (637 t/h) of feed coal. The separation results attainable by jigging have favored this unit operation as optimum for creating a clean coal product as required by steam coal specifications. Al- though the jig is used in preparing coals which are difficult to separate, its limitations to achieve both quality products and high recovery are being recognized in comparison with heavy media-based processes which make sharper separations from feeds having high "near-gravity" contents. The accu- racy of the densimetric stratification in the upper portions of the jig bed are less precise. It follows that coals with more than 10% near-gravity material

Jan 1, 1991

By G. A. Kordosky

The control of pH in solvent extraction circuits is an old technique (1,2) but one which has a large potential for future use. The equilibrium position of any reaction which has hydrogen or hydroxide ions, either as products or as reactants, can be controlled by pH adjustment. Several examples of reaction types which are important in solvent extraction systems and which also show a pH dependence are shown in Figure 1. The examples were chosen to show the wide variety of reactions which fit the above criteria, but it is not meant to be a complete listing of all the possible reaction types, Some of the reactions are presented in a simplified form. It is the intent of this paper to discuss pH controlled solvent extraction reactions for some relatively simple systems through more complex ones.

Jan 1, 1979

By W. E. Benton

The name Perlite applies to both a hydrated volcanic glass containing from 2% to 5% combined water and to the lightweight material that is produced from expanding the sized volcanic glass. Upon heating, Perlite expands to about twenty times its original volume which results in a material of low density, low thermal conductivity, and high sound absorpt'ion. Perlite ore is mined by open pit methods and is crushed and sized to provide specific gradations for expanding into products used in acoustical tile, built- up roofing, filtration, lightweight concrete and horticultural applications, among others. In 1983, the U.S. production of crude Perlite came from 12 mines and 6 western states, with apparent consumption and production estimated to be about 6% lower than 1982. The average price per ton was slightly higher than in 1982.

Jan 1, 1984

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center&apos;s 900-lb/hr pilot plant, approximately 85 percent of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to <1,000 ppm equivalent Si02, while maintaining a Ca(II) content of 516 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water.

Jan 1, 1970

The concept of "classification is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters which affect fines removal are identified and discussed, and a quantitative index for circuit fines removal effectiveness is defined. This approach lends new interpretation to certain observed phenomena, and suggests useful guidelines for circuit design and operation.

Jan 1, 1985

By Frank J. Foster

This Paper will deal with Bucketwheel Suction Dredging and its particular relationship to mining applications. There will be comparisons with other methods of suction dredging and descriptions of two recent bucketwheel installations in the mining area. The Directory of World Dredging Fleets published in the `larch 1984 edition of World Dredging magazine shows that there are about 1.000 conventional Cutterhead Dredges listed throughout the world with 289 in the United States. There are 242 Bucketline Dredges listed throughout the world of which only 6 are in the United States. These figures are not completely accurate because several units are known to the author that are not on the list and, of course, there may be others.

Jan 1, 1984

By Ronald C. Severson

Crystals of native gold occur in placer-type deposits. Gold, as a pure metal, is the most malleable metal known; therefore, delicate gold crystal forms should not survive mechanical transport and concentration processes involved in placer formation. To test the hypothesis that the crystalline gold is currently forming in place, two active gold-placer operations and an unmineralized background area in Alaska were examined. At these sites, rock outcrops, soil profiles, and native vegetation were sampled. At one sampling site, the soil was panned and yielded crystalline gold, as well as the more common rounded nuggets. The plants and soils were analyzed for their major, minor, and trace-element contents, especially gold. Two procedures, one a simple demineralized water leach and the other a partial digestion with acetic acid and hydrogen peroxide, were also used to extract gold and various anions from soils. The water-extractable gold ranged from <0.02 to 15.0 ppb Au in the extracting solution. This represents as much as a 104 enrichment in gold over average river water. This extractable gold is probably available to the native vegetation. Gold concentrations in the unashed dry plants from the two placer sites ranged between 0.4 and 106 ppb compared to a background range of <1 to <4 ppb Au. The presence of dissolved organic matter in the soils is thought to be responsible for the dissolution, transportation, and precipitation of gold in these placer soils, and this process is presently active in these soil profiles.

Jan 1, 2013

By A. T. Yu

The broken hill proprietary company Ltd., Australia&apos;s only steel producer, has come a long way. Since 1885 to reach today&apos;s. Capacity of 6.6 million long tons of ingot steel per year.* its Newcastle steel complex in New South Wales, located 100 miles north of Sydney and on-stream since 1915, has likewise shown continued impressive growth (fig. 1). The most recent expansion plans at Newcastle call for sub¬stantially increasing its production, with the help of some added facilities, but principally relying on the increase in efficiency of the furnace operation. Its modern raw materials blending system will playa major role in meeting Newcastle&apos;s new targets.

Jan 1, 1969

By G. H. Kuhnhausen

The Bear Creek Uranium Mill was designed in 1975 to process 909 tonnes per day (1000 STPD) of low-grade uranium ore from the Powder River Basin in Wyoming. The mill was expanded to 1818 tonnes per day (2000 STPD) in 1979. The Bear Creek Uranium Project is owned by the Bear Creek Uranium Company, a partnership of Rocky Mountain Energy Company and Mono Power Company. The original mill design contemplated processing ores from Bear Creek Uranium Company properties exclusively. The expanded capacity has been utilized for tolling ores from Kerr McGee Nuclear Corp. and other mining companies in the region. This paper describes the process of designing the original mill, the lessons learned from operation, and the design of the process modifications required for expansion. The project background, design philosophy, design basis, design criteria, actual flowsheet, special design considerations, and a comparison of assumed operating conditions and actual operating results will be presented. Bear Creek Uranium Company wishes to thank and acknowledge the help granted by the many operating companies who provided invaluable information, insight, and critique of the Bear Creek design through all the various stages and were instrumental in the successful completion and start-up of the mill. Without their contributions, the design philosophy used at Bear Creek would not have been possible and the results obtained would surely have been less satisfactory.

Jan 1, 1979

By Ramarao Inguva

Feasibility studies being conducted to investigate the use of electromagnetic methods for insitu volumetric heating of oil shales will be discussed. A two dimensional numerical model which describes eletromagnetic heating of oil shales is outlines. The model includes equations for temperature, pressure, saturations, chemical reactions, mass conservation, and source terms. The gases are all assumed to form one bulk species and the oil is assumed to remain in liquid form. The chemical reactions include pryolysis of kerogen and char, release of bound water, coking, and decomposition if carbonates. Porosity and permeability are dynamic functions of the organic materials. Calibration of the model is accomplished by comparison of the model results with experimental data obtained by IITRI. Nonlinear relationships for viscosity, thermal properties, and source terms and used as inputs to the model. A finite difference approximation to the differential equations is derived and solved using Newton&apos;s iteration technique. For the cases studied the solutions are quite stable. Numerical resultes are included and a preliminary study of the optimization of the heating process is presented.

Jan 1, 1984