Search Documents

By Dan J. Van Roosendaal

A closely spaced grid of survey points was installed over the tensile zone of a longwall panel in southern Illinois and monitored daily during subsidence to document the complex ground-surface movements associated with dynamic subsidence. Vertical and horizontal displacements were used to calculate maximum tilts and principal strains within the grid. The dynamic nature of subsidence is made evident by changes in both the direction and magnitude of maximum tilts and principal strains. The maximum tilt (smax) of 0.036 and maximum tensile strain (Emax) of 0.027 were measured after subsidence and were oriented transverse to the longwall panel. Observations of surface fracturing were correlated with strain determinations to estimate a surface strain at incipient cracking (E;) of 0.006 to 0.009. Using shallow inclinometers, a linear variation of horizontal displacement with respect to depth was observed, suggesting a neutral¬axis bending mechanism for near-surface deformation. Horizontal displacements transverse to the longwall panel reduce to zero at a depth of 40 feet. A linear relationship between strain and curvature was used to estimate ground-surface curvatures associated with Emax (0.00068 ft-1) and E; (0.00015 to 0.00023 ft-1). The curvature estimates are consistent with published results.

Jan 1, 1986

By Z. Yu

The effect of particle size on coal dewatering has been well recognized However, there are no systematic studies on ultrafine coal dewatering. The results discussed last year revealed the effect of flocculant type and coal wettability on the filtration of ultrafine coal In this paper, the differences in dewatering between -25 µ m ultrafine and -500 µ m fine coal with addition of flocculants, surfactants and oil-emulsions in vacuum filtration are further investigated Significant differences were observed in the reduction of the cake moisture. The utilized emulsions were found to be very powerful and promising filtration aids for both ultrafine and fine fractions of hydrophobic and hydrophilic coal

Jan 1, 1995

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/AgCl reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrode to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 1994

By H. Sevim

Long term production planning in open pit mines requires the determination of cutoff grade, mining and milling production rates, mining sequence, mine life, and ultimate pit limits. These variables interact in a circular fashion, that is, the value of a variable can not be determined without the knowledge of the value of the preceding variable in the circle. Therefore, a genuine solution to the problem necessitates simultaneous determination of the variables. Such a solution methodology, comprised of a group of heuristic algorithms and an unconventional dynamic programming algorithm, is described in this paper. The methodology is applied to a small size Western US gold deposit to illustrate its logic and capabilities.

Jan 1, 1995

By G. A. Kordosky

The literature contains several references to the influence of copper solvent extraction reagents on crud formation, but, there is disagreement as to whether the reagent has an influence on crud generation. The results of three pilot plant campaigns, where crud generation was studied as a function of the copper solvent extraction reagent, are reported. These pilot plants were run at operating copper solvent extraction plants using the aqueous solutions being treated by the commercial copper solvent extraction plants. Two of the pilot plant studies showed that the copper solvent extraction reagent had a significant influence on the extent of crud formation while the other pilot plant study indicated the copper solvent extraction reagent had a lesser influence on crud generation.

Jan 1, 1996

By D. W. Niosi

In this chapter, a review is made of the various stages of an exploration program, mineral rights acquisition methods and the partners involved in an agreement, the after- tax cash flow approach using present value discounting principles, the establishment of computerized financial models for assistance during the negotiating stages for a mineral property, and the various evaluation techniques and their specific applications during different phases of an exploration program. A set of examples is shown encompassing the initial target-seeking stages to the ultimate feasibility study stage.

Jan 1, 1979

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

By Charles T. Steuart, Richard B. Berg

Tripoli and the related mineral commodities such as micro- crystalline silica have been mined for more than 100 years for their abrasive properties. Although abrasive and buffing compound markets are still very important, within the last 15 years the filler and extender markets in paint, plastics, rubber, adhesives, and sealants have increased substantially. Tripoli or microcrystalline silica consists almost entirely of very small quartz crystals, many less than one micrometer in length. Material mined from different districts differs in crystal shape, grain size, and texture of the rock, all of which influence markets. Most US deposits are now mined by surface methods, and both air floated and micronized products are marketed. Deposits of tripoli now mined in the United States occur in chert-bearing Paleozoic limestone in the central part of the country with producing districts in southern Illinois, central Arkansas, and eastern Oklahoma. Although deposits within each district are confined to specific formations and extend laterally within those formations, individual bodies form minable deposits that are typically several hectares in areal extent. Tripoli is white to cream to rose and characterized by high porosity and ease of disaggregation. DEFINITIONS Tripoli In the United States, tripoli was first used to describe the fine-grained, easily disaggregated material from Seneca, MO, be- cause of its similarity to a rock from the Tripoli region of North Africa (Hovey, 1894). The North African rock is actually diatomaceous earth, a material that is similar in appearance to the rock from Seneca, but is of entirely different origin having formed by the accumulation of siliceous remains of microscopic marine or fresh- water animals. Tripoli is best defined as a very fine-grained, generally porous rock that consists of microcrystalline quartz, typically formed by the alteration of a chert-bearing limestone. Tripolite A term used to describe a rock from the vicinity of Tripoli in North Africa which is diatomaceous earth (Quirk and Bates, 1978) Microcrystalline Silica Microcrystalline silica is the same material as tripoli, but the distinction between the use of these two names is dictated largely by convention and markets. Material produced from southern I1linois deposits and used in white pigment and filler applications is generally referred to as microcrystalline silica, whereas that used in abrasive applications, both from the Illinois district and from other states, is commonly called tripoli. Amorphous Silica Amorphous silica, a term formerly used to describe the material produced from the deposits in southern Illinois, is now replaced by the term microcrystalline silica. Amorphous silica came into use when even optical methods for the identification of very fine- grained quartz were not widely available and the Illinois product, composed of quartz grains too small to be seen with the unaided eye, was thought to consist of amorphous silica. The Illinois material is clearly crystalline quartz, as shown by X-ray diffraction analysis and scanning electron microscopy (Fig. 1). Novaculite Although originally used to describe a rock suitable for the manufacture of whetstones, novaculite is now defined more generally " - as a homogeneous, mostly white or light colored rock, translucent on thin edges, with a waxy or dull luster, and almost entirely composed of microcrystalline quartz" (Steuart et al., 1983). The more compact rock mined in central Arkansas from the Arkansas Novaculite is referred to as novaculite, whereas the more porous rock is referred to as tripoli. Rottenstone The commodity rottenstone is sometimes included within the general mineral commodity category of tripoli. Rottenstone is mined in Northumberland County in eastern Pennsvlvania and formed by the weathering of a siliceous shale of Devonian age (Faill, 1979, Berkheiser, private communication, 1991). This material is used as a filler and extender, but is apparently unlike tripoli both in origin and physical properties. Spiculite Spiculite is a rock consisting of siliceous sponge spicules having formed by the removal by solution of the carbonate matrix of a spicule-bearing limestone. Spiculite has been mined in Texas and, because it resembles tripoli in several aspects, is included in the discussion of deposits.

Jan 1, 1994

By J. P. Fitzgerald

This paper is an accumulation of information on the geology, mineralogy and mining of the Hectorite clay deposit owned by NL Chemicals (U.S.A.), Inc. The mine is located in San Bernardino County, California approximately 35 miles east of Barstow and 1-1/2 miles south of U.S. Highway 40. The region is known as the Mojave Block which is a region bound by the San Andreas fault zone to the southeast and the Garlock fault zone to the North. The faults of both zones are active, vertical faults along which movements are mainly horizontal. Most of the faults within the Mojave Block are high angle faults which trend northwest. They are considered part of the San Andreas fault system and are a result of the right- lateral movement characteristic of this system. The east-trending faults are also high angle faults, along which movement has displaced rock units vertically. Manix fault is the only mapped fault that shows evidence of left slip which is characteristic of the Garlock sys tem to the North.

Jan 1, 1986

By R. S. Austin

One third of the world's and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. . Its whiteness, brightness, fine particle size, platelet shape, surface chemistry, and chemical composition make kaolin an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

By Sean Gallagher, Thomas G. Bobick, Richard L. Unger

This paper describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries. More detail can be found in Bureau of Mines Information Circular 9235 (Gallagher et al. 1990).

Jan 1, 1992

By Cahit Helvaci, Robert B. Kistler

Borates are defined as ' 'salts or esters of boric acid; a compound containing the radical B203" (Bates and Jackson, 1987). Borates are defined by industry as any compound that contains or supplies boric oxide. A large number of minerals contain boric oxide, but the three that are the most important from a worldwide commercial standpoint are: borax, ulexite, and colemanite. These are produced in a limited number of countries (Fig. 1), dominated by the United States and Turkey, which together furnish about 90% of the world's borate supplies (Lyday, 1991). Production in the United States originates in the Mojave Desert of California; borax and kernite are mined by US Borax from its large deposit at Boron. Borate containing brines are pumped from Searles Lake by North American Chemical Co., and a limited amount of colemanite is mined by Newport Mineral Ventures from Death Valley. Turkish production is controlled by Etibank, the national mining enterprise, which supplies most of the commercially traded ulexite and colemanite from mines in the Bigadic and Emet Districts, plus borax from the huge deposit at Kirka. Borate minerals have been employed in a wide range of uses for many centuries, dating from at least the 8th century when they were used primarily as a flux for assaying and refining gold and silver. Their valuable properties and relative rarity soon stimulated international trade in borates; Marco Polo claimed to have trans- ported Chinese borate minerals from Tibet to Europe, and his home port of Venice was the center for borate imports and use throughout the Middle Ages (Travis and Cocks, 1984). Borates were traded at relatively high prices for highly specialized applications into the late years of the 19th century. At that time they were being used for medicines, food preservatives, ceramic glazes, and in expanded applications as metal fluxes. It was in that era that borax was discovered in Clear Lake, CA, and more significantly, the playa deposits of western Nevada were found and exploited by F.M. "Borax" Smith and others. Research and development by Smith's company began the evolution of borates from a high priced commodity with a few specialized uses to the relatively low priced chemical raw material used in large tonnages on a worldwide scale today. Borates are often defined and sold by their boric oxide or B,03 content, and most statistical data are listed in tons of B203. Of the products sold by the industry, borax pentahydrate or 5 mol and boric acid are the most commonly traded commodities. Boric acid plants are operated by all of the major borate producers. Glass fiber insulation is the major end use in the United States followed by textile glass fiber and borosilicate glass, detergents, and ceramics. Detergent usage continues to be a major end use in Europe.

Jan 1, 1994

By Jack Parker

Cycles of mine convergence coincide with annual cycles of temperature and humidity in the mine. Laboratory measurements confirm that the presence of moisture reduces rock strength and induces internal rock stress. Findings are used in the design of mine openings.

Jan 1, 1969

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By Christopher Haycocks

Self-supporting, open stoping underground mining methods are some of the earliest, starting with the prehistoric flint mines of Europe and the Egyptian gold mines of Nubia in the time of the pharaohs. When the early miner created an opening, it had to be inherently stable and self-supporting to enable him to continue. Therefore, as mining progressed beyond simple gophering, self-supported open stoping methods were devised to meet the needs of individual ore bodies. Timber for support appears in mines as early as 1000 BC, but this was for no more than local ground control. The ingenuity of mining engineers through history has so refined open stoping methods that today they produce more tonnage than any other mining system. Self-supported open stoping finds its application in moderate to strong rocks that exhibit little jointing or fiagmentation. Good back, hanging wall, and footwall conditions that require no more than incidental support are an essential part of these mining methods. Open stoping methods find applications in all inclinations of ore body from flat to vertical, and where ore movement may be either mechanical or under the influence of gravity. Table 18.0.1 demonstrates the range of ore bodies suitable for open stoping, with particular reference to their dip and the deposit thickness. Most of the flat-dipping applications use ore pillars for overall support and ground control that may be recovered under some conditions after completion of normal stoping practices. In steeper ore bodies, rib, crown, and sill pillars used to block out the ore may be recovered subsequent to the completion of stoping. Open stopes are frequently filled to facilitate pillar recovery. Two of the methods, vertical crater retreat (VCR) and shrinkage stoping, utilize fragmented ore for temporary support in the stopes. In these two cases, the stope is not strictly open until after drawdown.

Jan 1, 2008

By J. Herbst, H. W. Kropholler, L. A. Cramer, E. T. Woodburn, J. C. A. Greene, G. Poling

A generalized mathematical structure is proposed whereby internal species mass flows within a flotation network are defined uniquely by a matrix of enhancement factors. An element of the enhancement factor matrix is defined as the ratio of the mass flow of that species leaving a given cell in the concentrate to the species mass flow leaving the same cell in the tailings. To predict the enhancement factors, knowledge of flotation kinetics effects is required. Recently experimental data has become available relating to the performance of industrial flotation circuits which indicate that the discrete or discrete-distributed kinetic schemes are capable of reasonably effective simulations. These simulations show the importance of including froth effects. The prediction of performance of networks from small-scale batch tests on flotation streams shows that the model for the froth phase used in the simulations does not scale-up well and that aeration effects are also difficult to predict. The network analysis should be useful in differential flotation of complex ores and it is disappointing in this context that little information on the kinetics of activation and depression is available.

Jan 1, 1976

What is your assessment of the current state of the minerals industry? It is no understatement that domestic mining is facing a severe crisis at this time. The sharp decline in commodity prices and demand is putting a great strain on domestic and worldwide mining, causing major declines in profits and market capital of mining companies. This, in turn, has lead to major production cuts, layoffs, shut-downs of operating properties, and the deferral of new and expansion projects. These changes in the minerals industry have played a major role in the health of the economy. Operationally, the industry continues to develop new technologies that are making our work more efficient, more cost effective and more environmentally acceptable and safe. During downturns like this, companies generally pay closer attention to operational efficiencies and process optimization. Historically, new technologies and processes tend to be developed during down markets, and I believe we will see the same thing as companies strive to preserve liquidity and maintain or improve their margins. On the positive side, the drop in commodity prices has resulted in a reduction in operational costs, as the costs for fuel supplies and construction materials have decreased.

Jan 1, 2009

By Lloyd H. Yeager

Good morning gentlemen. I'm very pleased to be a part of this fine program for the Society of Mining Engineers. Gypsum, as many of you know, is one of the most unique minerals on earth. The very excellent presentations which you have just witnessed, revealed the geological aspects of gypsum operations. It is not our purpose this morning to pursue this subject further. Instead, we felt you would be interested in some of the uses of gypsum . . . and what the future holds for gypsum products. To help accomplish this, we're going to first show the Gypsum Association's new film, "Shape Of The Future. ' This short movie traces gypsum f ram mines and quarries to its ultimate destination in homes, schools, offices -- in virtually every type of construction. We think you'll be particularly interested in the description of gypsum's fire resistive nature.

Jan 1, 1965

By George F. Weaton

During the past eight years there has been a dramatic change in the iron ore industry of Minnesota, in that its status has changed from that of a seller's market to a higly competitive buyer's market. Minnesota's natural ores must now be beneficiated and up-graded considerably to be marketed in order to compete with the higher grade foreign ores as well as with the locally produced and highly desirable taconite pellets. With the passage of the "Taconite Amendment' in the November, 1964 election, the taconite industry commenced to expand in Minnesota, which, although initiated in that state, was benefiting many other states and some foreign countries to a much greater extent than Minnesota. These other areas were actually appropriating markets that had been established and retained by Minnesota for many years. Since the approval by the state voters of this amendment, there has been a great increase in the development of taconite properties on the Mesabi Range.

Jan 1, 1966