Search Documents

Last year in the US alone, about 425 Mt (468 million st) of minerals and coal were beneficiated by froth flotation. This number indicates that from 1983 there was a 10% increase in tonnage of min¬erals and coal beneficiated by the indus¬try. A significant improvement was seen in the tonnage processed by the nonferrous minerals and coal industries. BP Minerals America installed 85 m; (3000 cu ft) flotation cells at the Bing¬ham Canyon mine and concentrator. The new flotation circuit has fewer than 100 cells compared to 2000 flotation cells used in the old plant (Mining Engi¬neering, November 1988). Column flotation use on a commer¬cial scale continues to expand as seen from the interest expressed at the Col¬umn Flotation Symposium (Column Flotation '88). The Magma Copper Co., San Manuel Division replaced all con¬ventional cells with 1.8 x 12 m (6 x 40 ft) column flotation cells for copper con¬centrate cleaning. Also, 1220 mm and 760 mm-diam (48 in. and 30 in.-diam) column cells are operating at the plant in the molybdenum circuit. A commercial Diester Flotaire col¬umn cell for fine coal recovery was installed at the United Coal Wellmore No. 20 plant. The 36.8 m3 (1300 cu ft) cell recovers 13.6 to 18 t/h (15 to 20 stph) of -590 gm (-28 mesh) coal. A similar unit has been installed at Tanoma Mining Co. in Pennsylvania. Various modifications of the column cells are being designed around the world. Jameson (Mining and Metal¬lurgy, 1988) described a new concept whereby the feed and air stream mixture is discharged into a cylindrical column of about 1.2 m (4 ft) height. Recovery and grade of nonferrous minerals have been reported to be better than that in a four-stage conventional flotation clean¬ing circuit. Flotation reagents American Cyanamid and Dow Chemical continued development of a new generation of sulfide collectors. A general feeling is development of new sulfide collectors has not kept up with flotation technology. Additionally, joint efforts between industry and chemical suppliers will likely be necessary to realize the economic benefits of the new technologies, since new chemistries respond differently compared to the conventional collectors. Flocculant development in recent years has been evolutionary rather than revolutionary. Rothenborg reported on development of a new flocculant family (a hydroxymated polyacrylamide desig¬nated S-6703) that has shown consider¬able promise in red mud clarification. Plant testing showed that this new floc¬culant could replace starch and poly¬acrylate and provide significantly higher overflow clarity. Barol Kami (Siirak) and Cleveland¬Cliffs (Hancock) reported development of an amphoteric apatite collector (ATRAC 873) that was used in Tilden's silica flotation process to increase apatite rejection. The collector was engineered for the particular flotation conditions in the complex Tilden process. Significant plant testing with ATRAC 873 showed that this reagent gave significantly in¬creased apatite rejection without any effect on silica flotation effectiveness or selectivity. Electrostatic separation Electrostatic separation is now em¬ployed in the precious metals mining industry to recover gold and silver grills from crushed slag. The installation at Paradise Peak has prompted other op¬erators to consider this application. In another development, attractive potentials for treating very fine minerals (-45 µm or -325 mesh) are being devel¬oped by Advanced Energy Dynamics and by the Department of Energy. Demonstration tests using triboelectric charging/electrostatic separation have been successful on a variety of minerals as well as coal. Magnetic separation Developments in magnetic separa¬tion have transpired on a production scale. Superconducting, high gradient magnetic separation has gained accep¬tance with the successful startup of a second unit treating kaolin at J.M. Huber Corp. This liquid-helium-cooled mag¬net generates 2.0 tesla in a 3-m-diam (120-in.-diam) bore with no power con¬sumption. Wet, high-intensity magnetic separation has been applied to sulfide mineral separations both domestically and abroad. These continuous type of separators are effective in removing residual chalcopyrite and sphalerite from other base metal sulfide concentrates. Separators using high energy rare earth permanent magnets are continu¬ally increasing. Now offered as both drum and roll type, these units are be¬coming a staple in the processing of industrial minerals. Tests using rare earth magnets strategically placed on a spiral concentrator have demonstrated the enhanced recovery of heavy miner¬als such as ilmenite. Classification Although no major technology break¬throughs in classification appear immi¬nent, there is an increasing need for more efficient and cost-effective meth¬ods to make size separations. It is be¬coming more apparent that mineral concentration methods will be more common at very fine sizes, say below 50

Jan 1, 1989

By William H. Engelleitner

Agglomeration by balling in cylindrical or shallow pan devices dates back to the early part of this century. The first sintering tests conducted by Dwight-Lloyd on nonferrous ores included a mixing step for ore, flux and fuel carried out in a deep pan device similar to the balling pans, or discs, presently in use. Further work directed mainly toward sintering of ferrous and nonferrous ores always included a preparatory step, usually referred to as mixing, agglomerating or green-balling of the ingredients. In the late forties and early fifties two methods of particle preparation prior to firing were in general use. In Europe the balling pan was used predominantly, both as a mixer and as a pelletizer. In the United States many pilot plants and semi¬commercial plants used balling drums. When the first iron ore pelletizing plants were built in this country, the most frequently used device for green-balling was the cylindrical drum. At the same time, the pan device was used both in Europe and the United States for many other materials such as fertilizer, cement, flyash, alumina and copper concentrates, as well as to mix the feed for sinter machines. The difference between these two balling devices - -the drum and the disc - has been the subject of much discussion and is well covered by several papers included in the 1962 publication "Agglomeration' issued by AIMS, based on their 1961 International Symposium held in Philadelphia. (1)

Jan 1, 1965

By George W. Luxbacher

The inclusion of a new term "planned subsidence" in the Surface Mining and Reclamation Act of 1977 has lead the U.S. coal mining industry into a new aspect of engineering: subsidence planning. Subsidence planning has necessitated the integration of geotechnical, civil, and mining engineering disciplines. Although much of the foundation and application work has been completed, subsidence planning is still a developing area. This paper discusses the application of subsidence planning in several brief case studies (a high voltage transmission tower, a sewage treatment plant, and a slurry impoundment), emphasizing the risk assessment aspects necessary to account for some of the uncertainties that may exist.

Jan 1, 1986

The need for an integrated approach to optimization of unit operations in both the pit and the mill has long been recognized, but the complexity and nature of the overall problem has up to now resisted solution. This paper reports on a modeling methodology which couples symbolic and numeric computing to unify operations in both the pit and mill. The ultimate goal of this work is to optimize all operations that are influenced by blasting. Blasting plays a key role in all facets of operations. Obviously, drilling and blasting costs are determined by blast design, but the down-stream costs that are closely related to blasting results are often treated as separate functions: loading, hauling, cleanup, and crushing and grinding are all heavily influenced. Diggablilty and bucket fill factor are a function of fragmentation, the condition of the floor and uniformity in the shape of the muck pile. Likewise, cycle times and loading delays partially determine haul cycles, while fragmentation distribution and size determines the efficiency of truck loading. Removal and breakage of oversize causes loading delays and increases cleanup costs. The influence of blasting doesn't stop at the crusher. Mill productivity, power consumption, and maintenance are a function of the feed. Even at the SAG mill a reduction of a critical particle size during blasting can increase throughput. Thus, a bottle-neck for production far removed from unit operations in the pit can be alleviated by a modification in blast design. The question is: how do we optimize blasting with respect not only to itself but to al\ related mining and milling operations? For that matter, how do we even model blasting so that we can control the results of a blast?

Jan 1, 1991

By Stuart M. Lipofsky, Norm Hutchins

The Metropolitan Water District of Southern California has undertaken the Lake Mathews Outlet Facilities project to replace the existing outlet facilities. In the late1990s, consulting engineers for the District determined that the Lake Mathews Outlet Facilities were susceptible to a catastrophic failure during a seismic event. To ensure a reliable supply of water to Metropolitan’s customers in the Los Angeles area, the District decided to construct new outlet facilities. This Project consists of excavating a large diameter junction shaft, a 6.10 m (20 ft.) horseshoe tunnel, three short 4.88 m(16 ft.) horseshoe bypass tunnels, and a large excavation within a cofferdam that were all driven in difficult rock conditions. Additionally, a new concrete outlet tower was constructed and connected to the existing tunnel by the new bypass tunnels and through the junction shaft. The J.F. Shea Co., Inc. of Walnut, California, is currently finishing the construction of the Lake Mathews Outlet Facilities Project for Metropolitan. The large diameter junction shaft is 50.60 m (166 ft.) deep, excavated 16.15 m (52 ft.) in diameter and lined with a61 cm (2´-0?) thick steel reinforced concrete lining to a finished diameter of 14.63 m (48ft.). The shaft was excavated full face with one stationary shaft three-boom jumbo, modified for the large diameter. The shaft also consists of four sets of gate guides extruding from the shaft wall towards the center of the shaft that provide the ability to operate up to four mechanical gates at any time, to open or close each tunnel. This paper will present the junction shaft excavation and concrete construction techniques, including the innovative slip form method utilized to construct the junction shaft.

Jan 1, 2003

By R. E. Miller

Hoisting coal using water and air is a technology which has potential to improve the economics and safety of transporting coal. The Coal Air-Lift Hydrohoist is a prototype coal hoisting system developed by the U.S. Bureau of Mines (USBM). This paper discusses the method used to regulate the supply of water to the 50-m-high hydrohoist U-tube such that the pressure difference at the bottom of the U-tube is held constant. Maintaining a constant pressure difference results in a steady flow of slurry out of the hydrohoist.

Jan 1, 1995

By D. A. Norrgran, J. N. Orlich

Described is the application of high- intensity magnetic separation throughout the spectrum of industrial minerals. Performed either wet or dry, the separation has application in both the recovery and concentration of value minerals and in removing deleterious mineral constituents. The various types of magnetic separators along with the design and operating parameters relative to separation response are characterized. The characteristics of specific minerals to magnetic collection and the production of high-grade concentrates are described. Laboratory, pilot-scale, and plant studies carried out on a variety of industrial minerals have demonstrated the effectiveness of magnetic separation as either a primary or a secondary unit operation to achieve product quality.

Jan 1, 1987

By George D. Roberts

Dams are constructed to retard the flow of water or debris; therefore natural forces are constantly at work to remove such obstructions. To circumvent nature and avoid expensive trouble with a dam requires thoughtful far-sighted planning, careful construction control and vigilant periodic inspections to detect and repair deterioration at its inception. Although the factuality of the foregoing statements is apparent, all too many have failed to consider them in the past as will many in the future. "The economic, but safe construction of dams calls for the highest order of technical knowledge, practical experience and sound judgment." (1)

Jan 1, 1967

On my arrival in New York after the Russian examinations John D. Ryan, president of Anaconda, asked me what my plans were. I told him I wanted to be useful somehow in the World War that we had entered while I was away, but I did not know how. Ryan and Thayer told me that the new American Air Corps was gathering a group of executives, most of them young, to go to France as Army officers to help with the industrial side of our aviation activities. This would include construction of military airports, maintenance, and supply for our rapidly growing Air Corps. They thought I might be accepted in this group of about 30. It seemed to be just what I wanted, and I put in my application at once. My application was accepted about three weeks later and I was told to come to Washington to take physical and other tests and to meet others of the group. I liked them. They were a cross section of competent American manufacturers, bankers, automobile executives, and merchants. I was the only miner. I had many discussions in the days in Washington with members of our organization and others I knew who were going into war service. Attitudes were very different from those 55 years later. There was no discussion as to whether war was right or wrong. We were in it and must do all we could to help. At the same time there was a holdover from the days when, at least for the elite, war was high adventure. Even the most high-minded did not then realize that war is a horrible form of wholesale murder and, in 1917, it would have been treason to suggest this. I had two weeks before our industrial group was to start work which gave me time for a hurried trip to Berkeley where Dorothy and I announced our engagement.

Jan 1, 1976

By Alfred F. Savage

The Oglebay Norton Company has traditionally been a supplier of metallurgical grade fluorspar gravel to the American steel industry and, in the early sixties, fluorspar pellets were entered into the market. The gravel has been imported from Mexico, the pellets were produced by the Minerva Company in southern Illinois. While the acceptance of the pellets by the industry was satisfactory, overall marketing considerations caused the Minerva Company to discontinue the pelletizing operations. Thus it was that Oglebay Norton came to the decision to revive earlier plans to produce fluorspar agglomerates. A survey of the market and related factors led into two basic conclusions: 1) Because of steel plant safety considerations, flat, pillow- shaped briquets were preferable to easily rolling, marble-like pellets. 2) Briquets competitive with gravel could be produced by cutting imported, low-duty, acid grade spar to metallurgical grade by limestone and binders. A plant was built in Brownsville, Texas, and started operations in early 1970.

Jan 1, 1975

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By T. J. Jr. DeMull, F. G. Miller, J. P. Matoney

For some time a need had existed in the minerals processing field for a relatively efficient separator that would treat high tonnages of particles in the intermediate size range, i.e., those particles too large for froth flotation and too small for conventional gravity-type separa¬tors. Among those devices developed to meet this need are the centrifu¬gal specific gravity separators. These devices employ centrifugal acceleration to assist gravitational acceleration in separating light¬density minerals from heavy-density minerals. In the category of centrifugal specific gravity separators are the heavy-media centrifugal separator and the water-only cyclone. The two major centrifugal heavy-media separators, i.e., the heavy-media cyclone and the DynaWhirlpool, as well as the water-only cyclone, are discussed in terms of: design features, operating variables, operat¬ing data, and flowsheet design criteria. Examples of plant applications are given in the field of coal processing as well as the processing of other minerals such as iron ores, potash, and tin. Finally, the subject of the staging of centrifugal separators and their use in combination with other separators is discussed. PRINCIPLES For coarse sizes of minerals, efficient specific gravity separations have been possible for many years with open-bath vessels using the natural settling velocity or buoyancy of the particles. These bath ves¬sels process ore by utilizing micron-size solid particles suspended in the slurry fed to the separator. The inclusion of these particles in the slurry increases the effective density of the separating fluid to allow particle separations to be made at densities greater than that of water. However, if vessel size is to remain within economical limits, the particles processed in the bath vessel must have high settling rates in a IG gravitational field. Because of this requirement, heavy¬medium bath vessels are usually restricted to processing +V4-in. sizes. To extend efficient specific gravity separation to smaller sizes, the gravitational acceleration of particles is replaced by centrifugal acceleration. The settling of a small particle in a fluid in a centrifugal force field is similar to that found in a static bath except that the acceleration due to gravity, g, is replaced by a centrifugal acceleration where v, is the tangential velocity at radius r: V=kdm(P-P,), V'. (J) µ In more practical terms where the particles settle in a suspension of finer particles comprising the heavy media and with an effective suspension density p" V = kdm' (P P ) . v'. (2) U r To date the most effective use of this principle has been obtained with devices that rotate a liquid or suspension within a stationary enclosure in order to create centrifugal force. Cyclones are the most common devices used for this purpose, because they generate centrifu¬gal forces far greater than the force of gravity and therefore not only have high capacities but can treat finer sizes than bath-type vessels can. The two main types of cyclones used by industry are the heavy-media cyclone and the water-only cyclone. Also quite widely used is the DynaWhirlpool, which, though based on the same princi¬ple, differs in design from the conventional cyclone. HEAVY-MEDIA CENTRIFUGAL SEPARATORS Like the bath vessels, the heavy-media centrifugal separators em¬ploy media composed of micron-size particles suspended in water. However, the centrifugal force generated in these separators accentu¬ates the difference in settling rate between particles of different density and thus makes possible separations of finer size particles than can be treated in bath vessels. The two most common heavy-media centri¬fugal separators are the heavy-media cyclone and the DynaWhirlpool. Heavy-Media Cyclone Although cyclones were originally developed for use as classifiers or thickeners, it was later found that they could also effectively serve as heavy-media separators.63. 64, Design Features Fig. I I is a schematic of a typical cyclone developed to serve for any one of the following purposes: as a classifier, thickener, or specific gravity separator. The cyclone consists of a cylindrical section joined to a conical section, usually having an included angle of between 14° and 25°. Feed enters the cyclone tangentially through an orifice attached to the cylindrical section. The overflow orifice is located in the base plate of the cylindrical section. The vortex finder, a tube attached to the overflow orifice, extends into the cyclone from the base plate of the cylindrical section. The underflow orifice is located at the apex of the conical section. As some medium together with mineral particles is fed through the feed orifice, a vortex with a hollow air core extending from the overflow to the underflow orifice forms in the cyclone while hollow spray discharges form at each of these orifices. Under the influence of the centrifugal force, high specific-gravity particles move through the medium to the wall of the cyclone and descend in a spiral flow pattern to the underflow orifice. Those particles in the feed stream, lower in specific gravity than the feed medium, follow the major portion of the flow to the center of the core where they are caught in the high-velocity upward central current and are carried out through the overflow orifice. Fig. 12 shows a family of curves that illustrates how materials of varying specific gravity are recovered by a cyclone. Since the specific gravity of the medium is 1.40, the particles of 1.40 sp gr actually act as part of the medium and, regardless of the particle size, split between the underflow and overflow of the cyclone in proportion to the volume split of the medium. Particles higher in specific gravity than 1.40 are recovered in the underflow of the cyclone at increasing rates as the difference in specific gravity increases and the particle size increases. Particles lower than 1.40 in specific gravity are dis¬charged through the overflow orifice at increasing rates as the specific¬gravity difference increases and the particle size increases. However, all the curves originate at the fluid-flow ratio point for the finest particles of any gravity. The fluid-flow ratio is defined as the ratio of the rate of fluid flowing from the underflow to the rate of fluid

Jan 1, 1985

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By William D. Meakins

INTRODUCTION Today, auxiliary fans, or boosters as they are sometimes called, are commonly used underground to provide ventilation for safe working conditions for personnel. Fans are installed in many ways and for many purposes; however, their use falls into three main categories depending upon the application. Auxiliary Face Ventilation For Coal Mines Usually the application of auxiliary fans underground in coal mines presents problems not normally encountered in other types of mining. Two of the major problems deal with liberation of methane at the coal face and the production of coal dust in the mining process. For these conditions it is necessary to use permissible (explosion-proof) type of equipment. As a result, these fans are discussed in a category by themselves. Auxiliary Fans For Tunnel and Drift Ventilation Tunnels and drifts present unique ventilation requirements. For instance, tunnels and drifts can be developed for considerable distances into virgin territory. Since they are generally dead-ended, the only way to obtain ventilation at the face is to use ventilation pipe to establish one leg of a ventilation circuit. The ventilation of tunnels and drifts therefore falls into another natural category. Other Uses of Auxiliary Fans For Mining Purposes Fans can be applied to mining applications in many ways other than those discussed under the other two categories. For example, many times auxiliary fans can do a much more practical job of proper air control and distribution that can be achieved with any other mechanical means; therefore, these other uses are discussed as a special category. AUXILIARY FACE VENTILATION FOR COAL MINES After 1936, federal and state coal mining laws prohibited the use of auxiliary underground fans in coal mines since such equipment had been widely misused. In certain cases, recirculation of face air had been allowed to occur thereby creating a serious potential explosive hazard by the possible buildup of excessive methane concentrations. By the late 1950s, mining machines with rapid face penetration were commonly being used in coal seams which liberated higher quantities of methane than in earlier years. As a consequence, in the late 1950s and early 1960s, the use of auxiliary face fans was again allowed under strict experimental conditions because conventional methods of face ventilation control without fans were becoming inadequate. Today, auxiliary face fans are widely used under strict federal and state control. Such auxiliary ventilation does not reduce the need for the amount of primary air from the main mine fans; however, it does help to distribute primary air more efficiently at the face. The present trend is toward an exhaust system of ventilation utilizing 406- to 610-mm (16- to 24-in.) diam tubing extending from the face to an outby auxiliary fan. Since the tubing is normally applied with negative pressure, spiral wire reinforced tubing has been replaced largely with metal and, more commonly, fiberglass tub¬ing. Additional auxiliary blower units are often used at the mouth of the room being developed, or installed on the miner or loader near the face, depending upon the amount of gas liberation present. Often one (or more) of the fan units is equipped with an integrally mounted hopper and feeder which automatically adds a continuously metered amount of rock dust to the exhaust air. The combination unit tends to make the mixture of discharge particles noncombustible and reduces to some extent the need for additional rock dusting of return airways. In this part of the chapter, typical auxiliary ventilation systems are described including curves and photograph of typical/applicable equipment. Reference will be made to "blowers" and "ex¬hausters." Both are fans and are basically the same units. They take on their name through the manner in which they are used. A blower usually has an inlet bell on the inlet side to help to obtain good air flow into the blades. An exhauster often has a discharge cone added to reduce the discharge loss. Any basic fan unit can be used either as a blower or an exhauster. Description of Auxiliary Ventilation Systems Several auxiliary ventilation systems and modifications of basic systems have evolved over recent years. Some of these systems are described and illustrated. System No. 1, an exhaust system for faces with comparatively low gas liberation, is shown in Fig. 1. Here

Jan 1, 1982

By S. R. Dismuke

Ore at the Magmont Mine in southeast Missouri is extracted by the room and pillar method on two and sometimes three horizons. In 1991, an innovative plan was formulated for recovery of high grade ore in pillars using cable bolts to accommodate spans of more than 27 m (90 ft). A test area was subsequently selected and a recovery plan developed. A cooperative rock mechanics study effort by COMINCO METALS, the U.S. Bureau of Mines and the University of Utah was later established. When initially opened in 1968, the planned production rate was about 1,000,000 tons per year. Due to declining reserves, the production rate was decreased to 630,000 tons per year in November 1992. Pillar recovery now accounts for approximately 40%-50% of the mined tonnage and plays a vital role in allowing Magmont to continue to operate.

Apr 13, 2011

By Jean-Luc Cornet

Advances in conveyor technology over the past decade have enabled the design and erection of very long overland belt conveyors. Such conveyors usually require head and tail drives to lower the belt tension and belt strength required. This paper provides an overview of the problems encountered in controlling the head and tail drives on such conveyors and some of the solutions developed by CDI for several such projects.

Jan 1, 2002

By C. Cigna, M. Patrucco, D. Savoca, E. Lovera

The paper deals with the activity program and the preliminary results of a research work commissioned by IReR Research Centre and Regione Lombardia to the Department of Land, Environment and Geotechnologies of Politecnico di Torino. The aim is to define measurement, analysis and control criteria for the emission of chemical and physical pollutants from non-metal mining industries, with particular reference to noise and airborne particulates. Such emissions are related to health risks and annoyance problems, both for the working crews and the neighbouring population, and so, in order to get an effective sustainability of the industry, suitable reduction methods and assessment tools are required. A simple technique for the evaluation and forecasting of both the emission levels and deriving impact has been tested at different mining and quarrying sites, considering their differences in terms of layout and exploitation method, the latter ascribed to a series of main typologies as present in Lombardia region.

Jan 1, 2005

Because the Environmental Protection Agency has identified methane as a greenhouse gas, the importance of de gasification through gob wells has become more critical. It has been observed that the degree of methane emission is closely related to the geomechanical characteristics of coal bearing strata, roof, floor, and surrounding coal seams. Monthly production data from 250 gob wells were collected from the Warrior Basin in Alabama, and many interesting correlations were observed between methane production with longwall face width, face advancement rate, number of gob wells in a panel, and geologic columns. Extensive finite element analyses were performed to estimate the characteristics of the emission zone in an attempt to corroborate these findings. This paper describes an investigation for developing correlations between the geomechanical behavior of the methane emission zone with methane production.

Jan 1, 1996

By Richard Switalski, Mark R. Kritzer, Boro J. Lukajic, Robert Pintabona

Ground freezing was chosen as an initial support method during construction of two deep shafts at the Mill Creek project. The Mill Creek, Phase 2 tunnel (MCT-2) is utilized to convey and store combined storm and sanitary sewage collected from the member communities in the greater Cleveland area. The main objective of groundfreezing was to provide a strong support structure to resist soil and groundwater pressures. This was achieved by creating a watertight, frozen-ground barrier around the shaft perimeter. The paper will provide an overview of ground freezing techniques applied during the construction of two shafts, each 250-feet deep.

Jan 1, 2003

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982