Search Documents

By C. Einberger

Groundwater Monitoring is typically required by regulatory agencies at potentially hazardous landfills or surface impoundments. Agencies have often required an arbitrary number of wells with limited evaluation of the effectiveness of the network to detect a leak. A Monitoring Efficiency Model (MEMO) has been developed to improve the design and cost effectiveness of monitoring well networks. MEMO 15 an analytical model that simulates the migration of hypothetical contaminant plumes from a site and quantifies the efficiency of alternative well network designs in detecting the plumes. The computed monitoring efficiency provides a quantitative measure of the well network adequacy based on hydrogeologic considerations. The model was recently used to design the groundwater monitoring well network for a heap leach pad at the proposed Beartrack Project.

Jan 1, 1993

By M. P. Oommen

This paper provides a brief look at a proposed short-longwall for coal, development. The proposed method is an attempt to realize the advantages of longwall mining in deposits that, historically, would only be minable by continuous mining methods. An overview of the proposed layout, development requirements, production rate, ventilation scheme and other associated features is provided. This mining method could help operators in above-drainage seams where minable areas are smaller. It may also have application in areas that are peppered with gas wells and in environmentally sensitive areas which preclude the use of conventional longwalls.

Jan 1, 1993

By Jan M. Mutmansky

While production scheduling for both surface and underground mining operations is similar in nature, a rather large array of techniques is applied in solving such planning problems. The techniques consist of both rigid operations research (OR) methods and practical procedures which are not mathematically based. In the following sections, a short summary of some of the techniques that are applicable to production scheduling problems in mineral operations is presented. The techniques discussed are: linear programming, integer programming, dynamic programming, graph and network theory, simulation, and heuristic methods. For an in-depth comprehension of these techniques, the reader is referred to any of the available textbooks on these subjects. One or more references will be listed for each topic to provide a starting point.

Jan 1, 1979

By John D. Katsllometes

In the mining and processing industry, the maintenance plan has often evolved rather than being consciously set up resulting in an overreliance on breakdown and fixed-time maintenance (planned maintenance). Historically mining and processing plant equipment has been robust and less automated than modem equipment, making it relatively easy to work on. Mining and processing plants have relied on large and expensive maintenance departments to enable rapid attention to breakdowns. Maintenance itself can result in excessive downtime and costs. This results from the requirement to take the machinery off-line to carry out (possibly unnecessary and invasive) maintenance. The danger of infant mortality after it has been put back on line again and also the cost of the maintenance action itself contributes to costs. A goal of any well-run maintenance program is to have the lowest cost while providing 100% capacity 100% of the time to operations. When maintenance investments are at a minimum, the cost of lost production is at its highest. As maintenance effort and investments are intelligently increased, the production loss gradually decreases until the lowest combined cost is achieved. This is the maintenance goal. A road map is needed to achieving maintenance excellence. This article addresses a "Road Map" to achieving maintenance excellence. INTRODUCTION Mining and processing industry maintenance is big business. A world-class maintenance program is characterized by maintenance excellence.

Jan 1, 2004

By C. J. Bise

Virtual reality (VR) is a concept in which the human experience of perceiving and interacting with a computer-modeled environment is achieved through the use of sensors and effectors. It is an advanced form of computer graphics. The images are generated based on where the user looks and how the user moves. As personal-computer-based (PC) instruction gains acceptance as an innovative approach to providing safety training, VR can provide a multisensory, rather than merely a multimedia, mode of presentation. New technology continues to be introduced into the mining industry to meet the productivity needs of coal and noncoal producers. There is also an increased need for more innovative training of mine workers. New technology and equipment designs often affect the basic causes of accidents. For example, the development of cabs and canopies for underground coal-mine equipment has reduced the number of accidents related to roof falls and rib rolls. However, safety-training specialists then had to focus on the machines themselves, because the modifications had the potential for causing "pinch-point" accidents. In fact, although the overall physical demands on mine workers have diminished, there has been an escalation in the concerns about trauma from repetitive physical activity. Thus, health-and-safety training specialists have shifted their atten¬tion to the recognition, evaluation and control of workplace hazards (Hancock and Hill, 1995). Recognizing that the spatial relationships of a workplace convey more information about hazards when experienced rather than described, trainers agree that simulation is the method of choice. Unfortunately, until recently, simulation systems were either simple software programs that did not come close to portraying the real experience or were complex hardware systems (such as flight simulators) that did, but at a cost of millions of dollars (Fritz, 1991). However, researchers and training specialists are excited about an emerging approach to work-force education based on virtual reality. VR is also described as cyberspace, immersive simulation, artificial reality, telepresence, virtual environment or virtual world (Meyer and Dunn-Roberts, 1992; Peterson, 1992). It represents a group of concurrent advances in computer and interface technologies. They enable an individual to interact in a multisensory way with a computer-generated environment. To achieve this, a typical VR system incorporates a computer that contains the necessary databases for producing realistic images and audio; a head-mounted display (HMD) or screen for viewing the images; and a three-dimensional controller, joystick or data glove for interacting with the computer-generated environment. If virtual reality is to become an effective tool for the safety training of mine workers, its attributes will have to be measured against other forms of delivery. Accordingly, Carr (1992) listed the following areas in which VR should be considered the method of choice: ? When training mistakes would be costly. ? When the necessary environment cannot be experienced in the real world. ? To build interfaces that are sensible and can be manipulated. ? To make training situations really "real." ?To make perceptible the imperceptible.

Jan 1, 1997

By Martin L. Smith, John M. Kemeny

In blasting, an optimal muckpile size distribution can be found in terms of mining and milling productivity and cost. Fragmentation control requires a means of modeling and evaluating blast results. A principle problem in the practical application of empirical blast fragmentation modeling is the evaluation of the muckpile's size distribution. Image analysis of video and photographic records of production size blasts at Cyprus's Miami and Thompson Creek mines is being used to provide data for estimating parameters relating fragmentation to blast design, energy factor and rock quality. The application of image analysis to the estimation of particle size distribution is reviewed with regards to the problem of fragmentation modeling.

Jan 1, 1993

If a fire occurs outby an underground coal mine section, the immediate safe evacuation of miners from the working section should always take precedence. Unfortunately, in many cases, the dedicated escapeways (escape routes) for the evacuation of the miners become contaminated by the byproducts of fire from the adjacent entries. The purpose of this paper is to present the ventilation-control process that would keep the escapeway free from contaminants and, thus, available for travel. A few scenarios of mine fires in longwall development panels are analyzed and discussed. To perform these studies, a mine fire simulator (MFS) was used. This (MFS) provides a dynamic representation of the fire's progress (in real time) and gives a color-graphic visualization of the spread of oxygen, combustion products and temperature of the gases throughout the ventilation system. Also presented and discussed are ways in which the MFS can be used as a training and teaching tool for miners and, particularly, for ventilation and safety specialists.

Jan 1, 1997

By Richard R. Klimpel

This paper reviews the use of sulfide mineral collectors in industrial flotation practice. The approach of the paper is to characterize sulfide mineral collectors in a number of ways, including by chemical structure, by influences with different classes of mineralogy, by interactions with particle size, and by interactions with frother type.

Jan 1, 1999

By Kadri Dagdelen, Thys B. Johnson, Salih Ramazan

Long-term production scheduling design is a very important part of mining because it determines the economic outcome of a project There have been many attempts to solve the optimum pit scheduling problem, but there has been no success in developing a scheduling method to give optimum results in maximizing net present value of a mining project. Open pit production scheduling problem can be formulated as a mathematical programming problem and solved using Mixed Integer Programming technique. However, it is not possible to solve the formulation within a reasonable time since the number of integer variables required for the mathematical model is too great to do that by today's available computer technology. There- fore, a methodology is required to combine, or aggregate, the mining blocks and to decrease the number of integer variables in scheduling without losing the optimality. Therefore, the fundamental tree concept was developed in this paper to combine the blocks. A fundamental tree is defined as any combination of blocks such that: 1. the blocks can be profitably mined, 2. the blocks obey the slope constraints and, 3. there is no subset of the chosen blocks that meets 1 and 2. A Linear Programming (LP) formulation is developed as a mathematical model to find a set of fundamental trees that exist for a deposit. Since the blocks are combined to form the fundamental trees, the number of variables required for the scheduling model is decreased significantly. This decrease in the number of variables makes it possible to mathematically formulate the multi-time period scheduling problem as a Mixed Integer Programming (MIP) model. A case study is performed on a multi-mineral copper deposit in Peru, South America. NPVs of annual after-tax cash flows generated based on the schedule provided by the "Fundamental Tree Algorithm" is compared with NPVs resulted from the schedules coming from three of the computer packages presently available to the mining industry. These are Mintec's M821V, Earth- work's NPV Scheduler, and Whittle's Milava open pit mine schedulers.

Jan 1, 2002

By J. A. Cervantes

A statistical model for assessing the risk of ground subsidence in abandoned mine areas is presented. The model is based on the relationship that exists between .the frequency and the location-of subsidence events in a given area and the physical conditions of the ground. These conditions can be described by a series of geological, mining, and physical variables. The model suggests the existence of regions in the multidimensional space of variables which are associated .with increases or decreases in the frequency of subsidence events. Regions associated with an increase in the frequency of subsidence events correspond to regions of higher risks, and vice versa. Risk assessment is based on the ability to express the limits of these high and low risk regions in the, space of variables, and on the ability to express the degree of membership of blocks of land within any of these regions. The theoretical framework for the model is extracted, from discriminant analysis. Risk is quantified by the probabilities of membership of blocks of land into any of these regions. Risk maps are produced by displaying membership probabilities in. appropriate contouring levels. The model has been applied in two urban areas where subsidence of the ground has been active in the past. The two areas are Penn Hills, near Pittsburgh, and Scranton/Wilkes-Barre in northeastern Pennsylvania. In this paper, only the results for the Scranton/Wilkes-Barre area are presented. Those for the Penn Hills area have been presented elsewhere (Cervantes, et al, 1990). In the- Scranton/Wilkes-Barre area, geostatistical estimates of variables likely to affect the stability of the ground were made using samples from 53 drillholes. The estimates were made for 2000x2000 ft squared blocks of land covering the study area. Discriminant functions were computed from the estimated variables and used to establish regions for classifying blocks of land into one of these two populations: 1) blocks not likely to have a subsidence event, and ii) blocks likely to have one or more subsidence events. The same, discriminant functions were used to compute membership probabilities for blocks of land to tall within any of these two populations. These probabilities were contoured to produce a risk map. The risk map produced compares well with the location of the subsidence events which have occurred to date in the area.

Jan 1, 1992

By David A. Roberts, Edward J. Cording, James W. Mahar, Robert A. Robinson, Noppadol Phienweja, Harvey W. Parker

Horizontal inclinometer and deflectometer casings were used to measure deformations up to 15.2 m (50 ft) ahead of and adjacent to the heading in highly fractured and sheared shales at the Stillwater Tunnel. The measurements were compared with borehole extensometer and tape extensometer deformations to evaluate ground movements in advance of, adjacent to, and behind an advancing tunnel heading. Ground deformations of up to 127 mm (5 in.) occurred during passage of the innovative "walking blade-gripper" TBM. Deformations were compared with curvometer/distometer and vibrating wire strain gage data from steel ribs to assess rock-support interaction.

Jan 1, 1985

By D. L. Purcell, B. T. McClure, J. McDonald

The U.S. Bureau of Mines has completed a laboratory evaluation of exhaust emissions from a diesel engine using an oxygenated diesel fuel. The fuels tested were soy methyl esters in a neat (100%) form and low sulfur, petroleum number 2 diesel fuel (D2). The engine tested was a Caterpillar 3304, indirect injection, naturally aspirated, 75 kW, diesel engine that is typical of engines used in underground mining applications. The objective was to determine the extent to which oxygenated fuels, such as methyl esters, reduce diesel particulate matter (DPM), and their influence on upon gaseous emissions such as total hydrocarbons, CO, NOx, NO2, formaldehyde, and other exhaust emissions. Heavy- and light-duty transient tests were used to simulate load cycles typical of mine applications. The soy methyl ester fuel produced greater amounts of volatile DPM (organic material) but much less nonvolatile DPM (carbon soot) for overall DPM reductions. A diesel oxidation catalyst (DOC) typical of the type commonly used in metal and nonmetal mines was tested with both fuels. The DOC further reduced the volatile and total DPM when used with the soy methyl esters, but increased the total DPM for D2 due to sulfate formation. The soy methyl ester fuel reduced CO and hydrocarbon, and NOx emissions. The DOC further reduced CO and hydrocarbon emissions.

Jan 1, 1995

By W. H. Schiffbauer

The U.S. National Institute for Occupational Safety and Health (NIOSH) developed an active proximity warning system called hazardous area signaling and ranging device (HASARD) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, which is worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels that are calibrated to identify levels of danger. The receiver outputs can include visual, audible and vibratory indicators, and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak and on a high wall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed, and it proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2003

By Mark Kuchta, Hans Engberg

The Swedish mining company LKAB operates two of the largest underground mines in the world today that together produce around 35 Mton of iron ore per year. During the 1990s, the company embarked on a massive effort to computerize its mine planning system. The goal was to combine various mine planning operations including mine surveying, geologic modeling, mine layout, production planning, and production follow-up into one modular based integrated system. The system was built around a large Oracle database and the Microstation CAD system. This overall design strategy and the various system modules are described, and some experiences gained using the system are discussed.

Jan 1, 2002

By J. V. Calara, J. D. Miller

The sign of the surface potential for complex non-reactive ionic solids cannot be predicted solely from consideration of the hydration energy of gaseous ions which constitute the ionic lattice. Accurate analysis of these systems must involve the hydration energy of surface ions, which requires knowledge of the crystal structure, the identification of cleavage planes, and the calculation of binding energies of surface ions. Surface binding energies for ionic solids can be deter- mined if the Surface Madelung Constant is known. A computational technique was developed for the calculation of Madelung Constants for infinite lattices which gives excellent agreement with the values calculated by other more complicated methods reported in the literature. Extension of this technique permits the calculation of Surface Madelung Constants and binding energies of surface ions, ?Us, for semi-infinite solids. The hydration free energy of gaseous Ions, ?Fh, together with the calculated binding energy of surface ions, ?Us, allows calculation of the hydration energy of surface ions, ?Gh, as for the case of the ionic solid, MX:

Jan 1, 1976

By D. Maxton

INTRODUCTION This paper traces the application of High Pressure Grinding Rolls (HPGR) at industrial and pilot scale in Australia. The Argyle Diamond Mine installed the first of two smooth segmented HPGRs during 1990 in an open-circuit secondary-tertiary crushing application to increase throughput. In 2002 a third HPGR was added to improve liberation and so increase the recovery of smaller diamonds. The latest improvements in wear technology (tyre with tungsten carbide studs) were incorporated in the design of this machine. Extensive HPGR pilot-plant trials were undertaken during the 1990s at both the Kalgoorlie Consolidate Gold Mine and the Boddington Gold Mine. The purpose of these trials was to evaluate HPGR as a method to increase throughput, as an alternative to SAG milling, and also to ascertain if downstream benefits existed. One of the challenges for HPGR circuit designers is to translate what occurs at small laboratory and pilot scale into what is likely to happen in a full-scale circuit. Scale-up from pilot machine results is normally recommended by manufacturers. However, such tests need relatively large quantities of material, particularly if meaningful data on wear are to be obtained. Laboratory tests are preferable, as they need relatively small quantities of ore, but may be questioned in terms of how they relate to full-scale operation. Modelling and simulation have played a particularly important role in this respect in Australia. Models are available which have proven to be very accurate at being able to scale throughput and specific energy response from laboratory to industrial machines. More recently, work in Australia has also been done in developing a model which has the potential to scale laboratory wear data as well.

Jan 1, 2004

By J. A. King, D. R. Weir, P. C. Robinson

Preconcentration of Porgera ore results in high recoveries of gold into gravity and flotation concentrates. The bulk of the gold is contained in auriferous pyrite flotation concentrate and is not readily recoverable by direct cyanidation. Oxidation in autoclaves at high pressure and temperature produces a residue that contains the gold in recoverable form. Pilot plant treatment of the autoclave residue is described, through washing and jarosite decomposition stages, to cyanide leaching and recovery of gold and silver by carbon-in-pulp techniques. The concern associated with disposal of plant effluents are also addressed.

Jan 1, 1987

By J. Luo

A major design problem for upper seam longwall gate roads that are to be constructed in a multi-seam environment is to predict the effects of stress field changes created by interaction. To quantify these effects, case study data were analyzed to develop empirical stress transfer relationships between seams for both longwall and room and pillar mining. Data analysis showed vertical movement and roof characterization in the upper seam to be controlling factors in damage prediction and, therefore, gate road planning and design. CMRR (Coal Mine Roof Rating) was correlated with the multi-seam roof characterization systems previously used. A WINDOWS-based software package named UGLY (Upperseam Gateroad Longwall Stability) was developed. Results from selected case studies were correlated with upper seam stress predictions.

Jan 1, 1997

By John S. Anderson

The need for fuels and minerals in this country is estimated to double, triple, or even quadruple by the end of the present century. Even assuming more recycling of scrap metals and some priority allocation of energy, as has been done, for instance in war time, the projected increase in the nation's population and ever-increasing wants of that population will require vastly more minerals than are now being produced. Since mineral ores are being mined at lower grades, and since all minerals, including fuels, are having to be mined from deeper deposits, the amount of surface land to be disturbed will, inevitably, be increased. We cannot depend on foreign sources to supply all the extra requirements, since the non-U.S. population is increasing, in most cases, faster than our own. Furthermore, starting from a lower base, their mineral needs may accelerate more rapidly than ours. Restrictions on exports may be applied in foreign countries, if it appears that remaining reserves are not sufficient to fill the national needs. In vice; of the opposition which the mineral industry is receiving, as has been well described at these sessions and elsewhere, what can we, as mineral producers, anticipate as regards our ability to continue to operate, to sway nothing of expanding production? Although not minimizing the problems involved, it seems obvious that, except under emergency conditions, the country cannot tolerate a reduction in the available

Jan 1, 1971

I met Austin Taylor in Vancouver on my way home from my first Pioneer examination. He asked me to examine the unsuccessful old Lorne mine, adjoining and west of the Pioneer. I had no idea that this meeting would lead to one of the outstanding successes and pleasant associations of my career. I knew nothing of Taylor, except that Gen. McRae and associates said that he had been engaged in lumbering and was interested in an oil and gasoline marketing company called Home Oil. But even if the Lorne examination would be only a small one, in the depths of the Depression in 1931, I was glad to have a chance to look at another gold property, so I agreed to visit the Lorne early in August. The start of the trip was not auspicious. I had been working hard on an unproductive study, and was greatly worried by my father's hopeless illness with tuberculosis. To get a little rest on my way north I had arranged to go from Seattle to Vancouver on the night boat that connected with my train. To my surprise, Bill Boultbee, an associate of Taylor, met me at the train in Seattle at 9:30. He said he would drive me to Vancouver, arriving at one In the morning. I was so tired that I begged off and let him take the drive alone Boultbee was most understanding and friendly, but I knew how I would have felt if I had been kind enough to take the long drive to help a stranger and then had been forced to make the return midnight drive alone. I was lucky they did not call off the examination at once. I got a good sleep on the Vancouver boat and Austin Taylor met me at the Hotel Vancouver for breakfast. After a brief talk he took me to the small steamer that made the 4-hr sail up Howe Sound to the village of Squamish. This was the end of the Province-owned Pacific Great Eastern Railway that was eventually to be a shortcut from Vancouver to the Canadian National main line at Prince George. Because

Jan 1, 1976