Search Documents

By John W. Crawford

The majority of the regulations in Part 75 for underground coal mines have been in effect since March of 1970, almost nine years now. Although there have been some additions each year in specific areas where the need became apparent or the statute required some action, the bulk was promulgated on March 28, 1970 for the purpose of clarifying the statutory provisions of the Federal Coal Mine Health and Safety Act of 1969. Many of those regulations were derived from the Federal Mine Safety Code, or from experience gained by the Bureau of Mines in the enforcement of Public Law 552. Upon passage of the Federal Mine Safety and Health Act of 1977, these same regulations remained in effect and the statutory requirements of the Act placed a responsibility upon the Secretary of Labor to promulgate additional regulations in specific areas not previously covered. The Federal inspectorate has received formal training at the National Mine Health and Safety Academy in the proper application of the regulations, as well as routine retraining and special training courses subsequent to the promulgation of new regulations. With some exceptions, the vast majority of these regulations are nothing more than good mining practice. Basically, the regulatory problems are two-fold. There are a few specific regulations that, under certain circumstances, compliance is nearly, if not actually, impossible. There is non-uniform application of enforcement of regulations by the inspectorate based on opinions developed from personal experience of inspectors or lack of experience. The record is replete with examples of overzealous inspectors applying regulations that either do not exist or have been stretched far beyond the intent of the regulations.

Jan 1, 1979

By G. F. Ayakwah

Point load strength (Is50) and slake durability (ID2) indices provide a measure of the strength and durability of rock fragments and are related to the alteration intensity and frictional resistance of the materials. Samples were collected from the rock piles, alteration scars and debris flows at the Questa mine with the purpose of examining relationships between Is50 and ID2, mineralogy, chemistry, weathering, hydrothermal alteration, and other geotechnical parameters. The Is50 from the various rock piles ranges from 0.6-8.2 MPa and the ID2 ranges from 80.9-99.5%. The Is50 and ID2 results indicate that the samples from the debris flows are stronger (average Is50= 4.0 MPa and ID2= 98.4%) than the rock-pile samples and that the alteration scar samples are weaker (average Is50 = 2.8 MPa and ID2 = 89.2%) than the rock-pile samples, but still most of these rocks are strong in terms of their Is50 and ID2. The Is50 decreases as the degree of alteration increases in some rock pile and alteration scar samples, but not in all. However, the majority of the rock fragments within the rock piles still indicate high strength, even after 25-40 years of weathering.

Jan 1, 2009

By P. Massacci, F. La Marca, G. Bonifazi

Some deposits of inhomogeneous materials, which occur near the surface and are exploitable by open-pit mining, may he characterized in real time prior to mining through groundsurface imagery. If the slice to be stripped is not overly thick, surface texture and color properties may be extrapolated to its entire thickness. Image-analysis techniques for processing ground-surface images acquired in situ or in the laboratory shortly after their acquisition have been developed. These images yield pattern vectors representative of red, green and blue (RGB) color component distributions and hue, saturation and brightness (HSB) texture parameters. The techniques were applied to a sandy ore deposit containing three lithotypes. Geostatistical analysis indicated that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multibarycenter classification algorithm. Such in situ image-analysis procedures provide a means for selecting the ore to be mined, selecting the proper ore-processing method and determining the appropriate blend to he processed. This can be done either before or during mining.

Jan 1, 2000

By Leo J. Miller

Sulphur deposits occur within the upper Salado and Rustler gypsum beds. The formation of a sulphur ore deposit requires large quantities of oil and /or gas, which must find a permeable pathway into the gypsum beds. The Permian beds weathered for 90 million years in an arid environment prior to the advent of a more humid climate at the beginning of the Cretaceous Period. The first Cretaceous rivers enlarged the sinkholes and caverns of the Karstified Permian terrain and deposited coarse conglomerates and sands into the subsurface gypsum beds. The resulting network of caverns and sinkholes, filled with permeable sediments, permitted the free flow of hydrocarbons through gypsum. All sinkholes and caverns infilled with Cretaceous sediments that have penetrated beds of gypsum are associated with sulphur deposits. The Castile gypsum lies directly upon the oil bearing Bell Canyon formation. Sinkholes and caverns filled with Cretaceous sediments occur in the lower Castile. Biogenic calcite and sulphur are adjacent to these sediments. However, faults assume the major role in generating the initial permeability, allowing hydrocarbons to penetrate the lower Castile gypsum. The largest faults are associated with biogenic calcite and sulphur for a distance of 250 meters up from the bottom of the Castile gypsum. It is apparent that two dynamic geological processes are generating permeability within the gypsum beds: (1) the Cretaceous sands decending with difficulty into gypsum and (2) the faults creating permeability in the lower Castile but losing energy through soft bed deformation in the overlying gypsum. Both of these sulphur ore controls are mappable, but another large sulphur deposit of the magnitude of the Culberson Sulphur Mine has yet to be discovered. It appears that massive sulphur deposits are associated with the largest scale examples of each system, that is (1) high densities of deep sinkholes and separately

Jan 1, 1992

By Stefano Colombelli, Nicola Bona, Gabriele Eccher, Luca Schiavinato, Paolo Cucino, Domenico Nave

"BIM technologies provide tools and processes to effectively support the entire life of an infrastructure, from strategic planning to maintenance. As a consequence, infrastructure design processes currently make frequent use of BIM tools. This paper describes the BIM oriented design of the underground railway extension in the metropolitan area of Catania. The paper highlights the design process and the chosen BIM tools considering the boundary conditions characterizing the project, i.e. basic information missing in the final design project, need of coordination between different design disciplines and designer companies, and, finally, need for a flexible design approach able to adapt to changes occurring during design development. INTRODUCTION The underground railway extension in the metropolitan area of Catania is composed of two lots of approximately two km each, namely “Stesicoro-Aeroporto” and “Nesima –Misterbianco”. Works to be realized are: •,Main tunnel: mechanized tunneling using a TBM-EPB machine, for the entire length of the lot; •,Underground stations: San Domenico, Vittorio Emanuele and Palestro, conventionally excavated as enlargement of the TBM tunnel after the partial demolition of precast segments; •,Ventilation and emergency shafts: connecting seven tunnel levels to road level on Stesicoro-Areaposto lot, six on Nesima-Misterbianco lot; •,Additional structures such as technical rooms and parking lot; •,Electric Substation at Monte Po' stop; •,Temporary works: TBM launching and arrival pit to be dismantled at the end of the works."

Jan 1, 2016

By Sundar S. Saluja

Efficient and re1iable methods of fragmentation through blasting have been sought ever since the introduction of black powder in mining operations, but the pace of investigation became faster with the discovery of nitroglycerine. The development of modern measuring instruments and the need to blast more rock with the least damage has made the study of blasting mechanics and its application more important, particularly since the oil embargo. Investigations into the practical approach evolved by Daws (1909) and the work done to make it more useful is discussed. The work of several investigators is touched upon with particular reference to the development of computer programs to simulate and optimize blasting operations.

Jan 1, 1986

By J. F. Able, F. Djahanguiri

The US Bureau of Mines conducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1998

By Xi Huang

The coal workers' pneumoconiosis (CWP) has been considered as the most serious health problem in the coal mining industry. The development of CWP in a worker lung depends on the average concentration and toxic components of the coal dust and the exposure length. Toxicity studies on coal dust shows the bio-available iron (BAI) in the coal dust plays an adverse role in the CWP development. It is also found that presence of calcite in the coal seams can significantly reduce the CWP cases as evidenced by the significant difference between the coal miners in the western and Appalachian coal regions. Based on this finding, it is proposed to artificially introduce calcite to BAI -containing coals in the effort to mitigate the CWP disease in coal industry. This paper introduces the scientific bases, the main geological factor that makes the differences, the proposed methods to introduce calcite to coal dust or to coal seams. Feasibility for the proposed methods is also discussed.

Jan 1, 2013

By John Frostiak, Don Welch, David Landriault

The use of paste technology for underground cemented backfill is widely accepted in the mining industry today as a potentially cost effective alternative to cemented rock and hydraulic slurry fill. While paste backfill is not the appropriate backfilling method for all mines, there are presently 23 operating tailings paste backfill plants throughout the world. This new technology has gained increasing acceptance as a backfill method over the last decade and its use is now expanding into the surface disposal of tailings using the stacked, thickened tailings disposal concept. Over the next 18 months there will be ten new paste plants commissioned in the world. Five of these ten plants will be used exclusively for surface tailings disposal or a combination of surface disposal and underground backfill production. The thickened tailings disposal concept, developed by Dr. Eli Robinsky in the early 1970's, has been in use for decades at several mine sites throughout the world (Kidd Creek Mine site in Northern Ontario), but always utilizing non segregating high density tailings slurry central discharge, stacked tailings placement. With the use of a higher solids content paste, the typical 2-degree beach angle can be increased to ten degrees or more with no runoff water and minimal shrinkage crack development through desiccation. This paper presents the design of the first mine to implement true surface paste disposal, Barrick Gold Corp's Bulyanhulu Mine in Tanzania. The paste system will be commissioned in the first quarter of 2001 allowing performance data to be collected to define the full potential of paste technology for surface tailings disposal.

Jan 1, 2001

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-adsorbed onto clay surfaces or inner layers, or organically bound. Rare earth minerals such as monazite exist in coal and have grain sizes smaller than 5 µm. In this study, froth flotation was successful in concentrating rare earth minerals existing in a thickener underflow material derived from Fire Clay seam coal that contained around 431 ppm of total rare earth elements (TREE) on a dry ash basis. Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2,300 ppm TREE. Using a laboratory flotation column to limit hydraulic entrainment, the TREE content was further enriched to around 4,700 ppm, which equated to an enrichment ratio of 10:1.IntroductionRare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets and batteries (Binnemans et al., 2013; Zhang et al., 2015). REE recovery from alternative sources such as coal and coal byproducts has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials.The average REE content of the world’s coal resources is around 60 to 70 ppm (Zhang et al., 2015). There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia with contents of 300 to 1,000 ppm, the Fire Clay coal seam in eastern Kentucky in the United States with contents around 500 ppm and the Sydney Basin in Nova Scotia, Canada, with contents of 72 to 483 ppm (Birk and White, 1991; Seredin, 1996; Hower, Ruppert and Eble, 1999; Blissett, Smalley and Rowson, 2014). The occurrence of REEs in coal and coal byproducts can be classified into three types: (1) rare earth minerals, such as monazite and xenotime, (2) ion-adsorbed REEs on clays and (3) REEs associated with organic matrices. The rare earth minerals in coal and coal byproducts are very small in particle size, generally on the micrometer and/or nanometer scales (Honaker et al., 2014). Froth flotation, which concentrates minerals based on surface chemistry differences, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime and bastnaesite (Abeidu, 1972; Cheng, Holtham and Tran, 1993; Pavez and Peres, 1994; Pavez, Brandao and Peres, 1996; Jordens et al., 2014). As such, flotation is a promising method for the concentration of rare earth minerals from coal and coal byproducts."

Jan 1, 2017

By G. Triantafillou

The aim of this paper is to present the progress of the plan of the Greek Public Power Corporation S.A. (PPC S.A.) at the Lignite Centre of Megalopolis in Peloponnesus (southern Greece) to manage impacts on local communities in areas affected by its activities during the lignite mining operation and post-closure. The reclamation works in the waste dump areas of the mines that constitute the Megalopolis Lignite Centre, concerning the utilization of waste dumps for infrastructure community projects constructions are discussed. Moreover, selected environmental indicators concerning land use and closure and rehabilitation are presented.

Jan 1, 2008

By T. Winkler, J. Tokarczyk, D. Michalak, W. Chuchnowski, M. Dudek

Engineering Methods aiding Sustainable Development of Mining Systems will be presented, and especially: virtual prototyping for designing of Mining Systems with Health Protection and Safety criteria taken into consideration, modelling and assessment of technical and health hazards that can occur during operation of Mining Systems, creation of knowledge repositories that disseminate safe work methods with consideration of existing language and culture barriers, dissemination of the methods integrating world community and Mining Systems users.

Jan 1, 2011

By Ian H. Clark

A series of numerical experiments were performed in order to elucidate the stress distribution, fracture strength and mineral liberation potential in single specimens of rock during crushing. Fracture strength was shown to reduce under eccentric loading conditions. Similarly, the presence of inclusions, both hard and soft, reduced the fracture strength. The predicted crack paths indicate that mineral liberation is unlikely to be preferential.

Jan 1, 1992

By E. M. Frizzell

Decisions affecting ground control design require detailed knowledge of roof rock geology. This is especially true when weak roof materials and anomalies create hazardous conditions and. if not properly supported, result in roof falls. The U.S. Bureau of Mines has developed a system to evaluate geological conditions by using a roof drill that will provide an estimate of the compressive strength of the roof rock in real time. Through the use of sensors and a microcomputer on the roof drill critical drilling parameters can be interpreted and analyzed almost instantaneously, making it possible to inform an operator of hazardous roof conditions such as voids and changes in strata during the drilling process. Geotechnical data can be downloaded to a portable semiconductor memory device, which is brought to the surface so that data can be directly accessed with a personal computer for further analysis. Results from field tests are presented.

Jan 1, 1992

By L. D. Savage

Several experiments were conducted using a large crib fire adjacent to a Kennedy Metal Products steel stopping in a simulated cross cut to evaluate the proposed mechanisms by which a mine fire would breach the stopping. Temperatures in the convective air paths on both sides of the stopping, at the surface of the roof and 16mm within the roof were measured to evaluate the effects of heat transfer. The results indicate that roof failure is the prime method of breaching this design of stopping.

Jan 1, 1996

By Klaus Böde

Within the national and international strategy of the German based construction company HOCHTIEF, the majority of its business units is equipped with the comprehensive software package ARISTOTELES. This software is a powerful business information system for all accounting and controlling related processes in medium-sized and large construction and other related companies. Due to the complexity of the software, time constraints, and limited financial resources an implementation of this software package requires thorough project management. In this paper the relevant elements of project management are outlined based on practical experiences gained during this international IT - implementation project. Special emphasis is directed to the identification and management of potential risks. In this case particular acknowledgement was given to the multinational nature of the project and modernization of the business. This includes thorough reorganization of the company, significant changes of job requirements, and substantial trainings for its employees. At the same time key success factors like knowledge transfer, adoption of Czech legal requirements, commitment of management, networked thinking, and integrated project planning come into play. The costs for implementation had to be carefully evaluated because the software was implemented in a country with a considerably low cost I price level. All these impacts to the business had to be managed within the scope of transformation of business and political environment from socialist to market driven economy.

Jan 1, 2002

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of a massive pillar failure in a room-and-pillar mine. The mine employed a nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated out by quickly, and, within 24 hours, it had covered an area approximately 1,250-m- (4,100 ft-) long by 762-m- (2,500-ft-) wide. The failure was caught and stopped by a solid barrier pillar. Using computer modeling, this study indicates that the massive failure was initiated because of a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of the absence of barrier pillars between some panels and between mains and panels. Based on computer modeling, alternative mine plans were proposed to avoid such problems.

Jan 1, 2002

By Stephen G. Hardcastle

CANMET has developed a simple yet very effective tracer gas method to test the efficiency of stench gas emergency warning systems which can easily be performed by mine personnel. This test method uses sulphur hexafluoride (SF,) as a surrogate for such stench gases as ethyl mercaptan. The test has many advantages: it is non-disruptive to production because SF, is odourless, colourless; it is safe to use as it is inert and only a small volume, insufficient to reduce oxygen levels, is necessary to dope the air with a measurable concentration; and most importantly it provides definitive results to assess the adequacy of the warning system. Specific findings of these tests have included, over doping sections of the mine and subsequent production loss due to sickness, the warning being ignored, the injection period being too short, excessive dispersion, and inadequate notification times. The simple test protocol involves releasing a known volume of the SF, under similar circumstances to those of the stench gas, and then sampling for its presence downstream. These samples are collected in air-tight syringes which are then analyzed in a laboratory with a gas chromatograph. By direct proportion, between the size of the stench and tracer gas releases, it is possible to convert the SF, concentration into equivalent stench gas concentrations profiles. From these, it is possible to define, the initial arrival time of the gas, the time it takes to reach a "target" notification concentration, whether the gas peak will exceed TWAEV, STEV and CEV exposure limits, and the duration of the peak above these levels. Since 1993, this test protocol has been employed a total of eight times on four different Canadian mine properties and the results are being used to optimize the stench gas release system with respect to volume of gas used, duration of injection, and number of injection locations.

Jan 1, 1997

By Ronald E. Yarbrough, Theodore L. Triplett, Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from a high-extraction retreat room-and-pillar operation in southern Illinois. The objective of this monitoring program is to study the inter- action between the ground surface and a structure during a subsidence event. Data from such a study should enhance the understanding of the mechanisms that produce structural damage and aid in the design of structures that resist such damage. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tiltmeter to detect and follow the tilt of the foundations caused by the mining subsidence sequence is demonstrated. Using data from this tiltmeter, the development of curvature in the foundations as they conformed to the displaced ground surface is shown. This curvature is rep- resented by differences in tilt at various points on the foundations, indicating a change in tilt over a horizontal distance. Also, even though subsidence damage has not been fully analyzed, preliminary observations of the cracks that formed in the foundations are reported. These cracks resulted in the separation of one footing into distinct pieces; therefore, their effect on the tilt readings is cited.

Jan 1, 1986

By Taghi Sherizadeh, Paul Brooks, Dogukan Guner, Samuel Nowak

Large excavations are well known to result in rock mass deformations which can present challenging situations for mine personnel. Most of the currently available ground movement monitoring devices fail to adequately provide mine operators with highly accurate and meaningful insights into rock mass deformation or displacement. The use of distributed fiber optic sensors (DFOS) in industries such as oil and gas and civil engineering has shown the potential of these sensors to deliver real-time, highly accurate, and long-range distributed strain measurements with great success. However, the use of these sensors in underground mining is limited to a few case studies.