Search Documents

By E. M. Cukrowska

The evaporative pan complex consists of two adjacent seasonal pans. These pans carry an exceptionally high salt (TDS) load due to over 50 years of effluent discharge via the pipeline from mines. The nutrient, heavy metal, radionuclide load in the water and sediments of the pans are very high affecting groundwater around the pans. The groundwater in the region contains TDS > 40 000 mgl-1 and sulphates > 7000 mgl-1, whereas groundwater in areas assumed to be unpolluted by mining activities have TDS < 500 mgl-1 and sulphates < 200 mgl-1. The extent of continuity between the pans and the groundwater is unknown, although there appears to be seepage of contaminated groundwater into the river system.

Jan 1, 2006

By Christopher Haycocks

Subsidence induced innerburden shearing and stress fields, whether active or passive, frequently contribute to significant ground control failures in overlying seams. In this paper proven multi-seam technology is used on upper seams to forecast and quantify the magnitude and severity of damage and the increased mining risk due to interaction. Increased upper seam ground control problems are demonstrated using hazard mapping which provides a viable technique for utilizing damage predictions in design.

Jan 1, 1986

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Gas holdup profiles in the collection zones of a pilot flotation column (0.91 m x 13.5 m) and a laboratory flotation column (0.057 m x 9.5 m) operated with air and water only were determined from pressure measurements. The profiles were determined discretely and continuously. For the pilot column, a minimum distance between pressure measurements was necessary to give reliable results. For the laboratory column, a third-degree polynomial fit to the pressure vs. height data was required. Water manometers proved to be less sensitive to sensor and process noise than pressure transducers. The profiles showed that gas holdup approximately doubled over a height of 8 to 10 m. The profiles were not linear, and the gradient increased towards the top of the column, especially for gas rates greater than 1 cm/s. The profiles cannot be predicted by a simple bubble expansion model. The implications of this new finding of a significant gas holdup increase with height in the collection zone on various aspects of flotation column design and operation are discussed.

Jan 1, 1996

By D. E. Ranta, M. G. Schulz

Mining of Molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the orebody. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1992

By John B. Ackerman, John G. Mansanti

INTRODUCTION Placer Dome&apos;s Turquoise Ridge Joint Venture operation is located some 75 km northeast of Winnemucca, a community in north central Nevada. Formerly known as the Getchell Gold Corporation and First Miss Gold, the operation mines refractory ore from the Getchell and Turquoise Ridge gold deposits located on the east flank of the Osgood Mountain Range above the Kelly Creek Basin in the Potosi Mining District. Mining has been ongoing at Getchell since shortly after its discovery in 1934, and was the nation&apos;s second leading producer of gold after Homestake in the early 1940s. Over its history the Getchell property has been mined for gold, tungsten, molybdenum and arsenic; mining methods varied from open pit mining to underground mining; processing options included conventional milling, flotation, roasting, heap leaching, and most recently pressure oxidation followed by CIL (carbon-in-leach). As an historical note, the US Bureau of Mines developed the use of carbon for gold recovery at Getchell during the 1940s (Horton 1999). Placer Dome acquired the property in May 1999. The pressure oxidation plant was mothballed in July 1999 and the property was placed on care and maintenance in February 2002 pending further exploration results. The property is currently ramping up to full production status. A joint venture agreement (75% Placer Dome, 25% Newmont) was established with Newmont Mining in 2003 and ore is processed at their nearby Twin Creeks autoclave plant. Mine dewatering is a key element to success. Arsenic is a ubiquitous mineral in many of the mineralized areas of northern Nevada, necessitating treatment of water prior to re-infiltration.

Jan 1, 2005

By E. Turner

This is the 3rd Paper in a series by this author, the first two being published at the two previous International Conferences. Since the Aachen Conference, Rio Tinto has carried out an extensive benchmarking exercise to see how we are positioned with respect to other leading companies (in our sector and other sectors of major economic importance). We need to be sure that Rio Tinto is at the forefront of best practises in Sustainable Development (SD) and is using the most effective tools and methods. This paper will present key findings from this work. Rio Tinto Minerals, working as representatives of IMA-Europe was a leading contributor to the European Commission DG Enterprise Voluntary Reporting Scheme for SD Indicators in the Non-Energy Extractive Industry. In Rio Tinto Minerals we have been using these SDIs in the management of our business and the paper will report on how they contribute to the management of our business and the paper will report on how they contribute to business value in: deepening customer relationships, eco-efficiency of operations, land use planning and permitting for new and expanding facilities, community relations, policy engagement with government authorities and strengthening the bond between the company and employees. We continue to support the Voluntary SDI Reporting Scheme, considering it to be important in the expanding EU and as a model for other regions globally. For example we have ore suppliers in developing countries and we use these SDIs in assisting them to better their performance, for we have an obligation to use our influence for continuous improvement. The paper will describe this work. Over the last 12 months our company has created a new Industrial Minerals unit called Rio Tinto Minerals which brings together all the borates, talc and salt operations, R&D, marketing, sales and customer care worldwide. The paper will present also the new Sustainability Policy of Rio Tinto Minerals.

Jan 1, 2007

By D. Malhotra, K. Purdy, G. Ramadorai

INTRODUCTION Today, flotation is clearly the dominant mineral concentration method. Since it is a relatively selective process, it is used for almost all sulfide minerals. A recent U. S. Bureau of Mines study indicated that approximately 225 million metric tons of sulfide ore was processed in 67 plants in the United States in 1980 (USBM Staff, 1981). There were over 100 plants processing copper ores in the world (Bassarear, 1985). Sulfide ores containing lead, zinc, copper, molybdenum, precious metals, cobalt, nickel, and iron are generally separated and concentrated by flotation. This chapter briefly reviews the plant practice related to the recovery of the above-mentioned sulfide minerals with emphasis on chemical reagents used for the production of marketable-grade products. PROCESSING OF SULFIDE ORES It is beyond the scope of this chapter to review the milling data for operating plants which have been extensively covered in literature (Tveter and McQuiston, 1962; Rausch and Mariacher, 1970; Weiss, 1985; Crozier, 1979). However, the following generalizations can be made regarding the processing of sulfide ores: 1. The primary grind is targeted to produce as coarse a product as necessary to provide an economic degree of liberation. 2. The concentration process, generally flotation, is designed to produce a concentrate consisting predominantly of valuable minerals and a middling fraction which may require further grinding to produce an optimum release of minerals. 3. The chemical reagent suite (collectors, frothers, etc.) for the separation of sulfide minerals from gangue minerals is generally complex. Total reagents used in the flotation process can be as high as six to eight, as is the case for lead and molybdenite separation from complex sulfide ores. 4. Chemical reagents are generally expensive because of the high selectivity for sulfide minerals. The process flowsheet is dependent on several factors, including ore grade and mineralogical composition. Generic process flowsheets for processing different sulfide ores have been developed for discussion in this chapter. However, there appears to be a consistent relationship between the reagent combination choice and the mineralogical composition of the ore (Tveter and McQuiston, 1962). These are covered in detail in the following sections. LEAD AND ZINC Galena (PbS) and sphalerite (ZnS), which commonly occur together, are the only minerals of lead and zinc, respectively, in most primary deposits. Feed ore grades are typically 1 to 5 percent Pb and 1 to 10 percent Zn. Very often economic quantities of copper and precious metals, silver and gold, also occur with these base metals.

Jan 1, 1986

By S. Chander

The advantages and disadvantages of various techniques available for controlling reagents in the mineral flotation systems are discussed. Special interest is placed on potentiometric and voltammetric sensors for monitoring flotation pulps. Different approaches to increase the sensitivity of detection and to facilitate in-stream monitoring of solution species are also discussed. The potentiometric sensors are simple to use but are limited by the availability of an electrode reversible to the species to be monitored. In some cases the response signal could be unreliable due to the presence of interfering species. In comparison, voltammetric sensors require a higher degree of instrumentation which, however, provides an opportunity to decrease interferences and increase levels of detection.

Jan 1, 1993

By William E. Robinson

Why did it fail? My first reaction when assigned this topic was to say: because somebody "goofed"--then thank you all for letting me say those few words, then promptly sit down. All of you have been bandying this problem around for many years--so all of a sudden I should come up with the solution. Well, While I might not provide you with your particular answer, I think I can show you some of the resolutions to it. Somewhere along your path of experience you may have discovered that a good formula for starting a fight is to tell a group of dedicated (Nordberg Crusher) users they should be using (Allis-Chalmers), or a group of (Allis-Chalmers) &apos;users they should be a (Traylor). Now, if you really want a melee, get both groups together and tell them they should be using a (Stedman Cage Mill). This is one sure way you can learn how great minds arrive at logical, well thought-out conclusions, based on all the relevant facts. Why did it fail? I could go on for hours giving you specific reasons why. One of my engineering professors used to start his new class off each year by writing on the blackboard--four and two, then turn to the class and ask: What is the problem? One brave scholar would venture to answer 8. His head would shake no. Another would dare 6. Again, a head shake. Now that the ball had gotten rolling, a number would vocally decide it had to be two, which produced only another shake of the head--no. All of them had missed the question he had asked : What is the problem? What he had gotten ,were some of the possible answers to the problem.

Jan 1, 1977

By Louis G. Silano, Aram Grigoryan

Parsons Brinckerhoff is providing engineering services for the Atlantic Avenue Station Complex Rehabilitation and Passageway Reconstruction for New York City Transit. Project reflects current realities and challenges of underground excavation, support, and construction under operating subway tracks and platforms, and under major transportation hub, comprising three subway stations, railroad terminal station, and busy street intersection. The construction requires extensive underpinning of subway structures and operating tracks. This Paper addresses engineering challenges of IRT subway station rehabilitation and passageway reconstruction without interruption of transit operations and street traffic. Total construction cost of the Project is $ 105,000,000.

Jan 1, 2003

By Steve Garcia

GEORGE WEINMAN: Our next speaker is Steve Garcia, operations vice president and general manager of mining at IMC-Agrico, Florida. Steve was born in Lakeland, Florida, to an IMC mining family. He has 17 years with IMC-Agrico and Freeport companies, including assignments in North Carolina, Nevada, Arkansas, and Indonesia. His work within the industry includes technical and operating positions including chief metallurgist, drying superintendent, and mines operations manager at Pane Creek. Other experiences include design of a grassroots phosphate facility in North Carolina; construction and start-up of a gold facility near Elko, Nevada; work in the Blytheville, Arkansas, ammonia urea facility; and three years managing engineering, construction, and support services in Irian Jaya, Indonesia. Steve&apos;s presentation is "Evaluation and Standardization of Multiple Slurry Pumping Systems."

Jan 1, 1998

By Joseph A. Dos Santos

The Expanded Conveyor Technology, a rationalization of the conventional conveyor technology, allows us to apply the theory and principles beyond the current (perceived) limits. This was first prompted by the writer&apos;s advancements in Sandwich Belt High Angle Conveyors. The introduction defines the Expanded Conveyor Technology and outlines the range of applicability for the wide variations in conventional and non-conventional conveyors. The writing deals with the theory and design of sandwich-belt, high-angle conveyors in the context of the Expanded Conveyor Technology, including the equations of friction, hugging pressure and the continuity of hugging principle; curvature constraints and criteria for tension, curvature, trough, and belt construction; and drive and tension analysis, load sharing and traction, including "derived load equivalents."

Jan 1, 2000

By J. W. Jang

The wear behaviors of grinding media with different chemical compositions and microstructures in wet grinding of a quartz-pyrrhotite mixture was investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation? behaviors. The galvanic interactions between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive conditions in a slurry. The rates of formation of passive films controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1989

By Harold B. Goldman

On the basis of tonnage, the sand and gravel industry is the second largest nonfuel mineral industry in the United States. In 1990, the production of sand and gravel was 927 Mt valued at $3.4 billion. California, which leads the nation with more than 126 Mt, together with Texas, Washington, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 Sieve (0.074 mm openings) to those passing a No. 4 Sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see chapter on Industrial Sand and Sandstone and Glass Raw Materials). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material that is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Sand and gravel is also used as construction fill, road base and subbase, and decorative material. Portland Cement Concrete Aggregates: Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15 to 20% water, 7 to 14% cement, and66 to 78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman and Reining, 1983). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate: Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.076 mm), uniformly coated and mixed with asphalt produced in the refining of petroleum. Sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement aggregate. GEOLOGY General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles that are sound and durable. Soundness and durability are terms used to denote the ability of aggregates to retain a uniform physical and chemical state over a long period of time so as not to disintegrate when exposed to weathering and other destructive processes. Individual particles must be tough and firm, possessing the strength to resist physical stresses and chemical and physical changes, that may cause swelling, cracking, softening, and leaching. The aggregate should not be contaminated by excessive clayey material, silt, mica, organic matter, chemical salts, and surface coatings. Physical Properties: The quality of aggregate depends upon its physical and chemical properties. These, in turn, may be inherent mineralogical and textural features of the rock or may be the effects of later changes such as tectonics, mechanical or chemical weathering, or incrustations. The physical properties most significant for concrete use are: 1) abundance and nature of fractures and pores, 2) particle shape and surface texture, and 3) volume changes which may occur because of freezing and thawing or wetting and drying. An aggregate is considered to be physically sound if it is adequately strong and capable of resisting the agencies of weathering without disruption or decomposition. Minerals or rock particles that are physically weak, extremely water absorptive, and easily cleavable are susceptible to breakdown. The use of such materials in concrete reduces strength or leads to early deterioration by promoting weak bond between cement and aggregate, or by inducing cracking, spalling, or popouts. Severely weathered, soft, micaceous, or porous materials may cause localized stresses to develop in concrete by swelling and shrinking during wetting and drying or freezing and thawing cycles. Physical Suitability of the Various Rock Types. Sedimentary rocks have a wide range in physical and chemical qualities. Sand- stones and limestones, if hard and dense, are ordinarily satisfactory, but many sandstones are friable and excessively porous and commonly are clay-bearing. Shales generally make poor aggregate material, being soft, weak, and absorptive. Most igneous rocks are satisfactory, being normally hard, tough, and dense. Tuffs and certain flow rocks may be extremely porous and have high water absorption and low strength. Metamorphic rocks differ in character. Most quartzites are massive, tough, and dense. Fine-grained marbles are usually durable, but coarse-grained marbles have low abrasion resistance. Gneisses are ordinarily very tough and durable. Some schists contain micaceous minerals that are undesirable because they are soft, laminated, and absorptive. Micaceous minerals are susceptible to splitting along cleavage planes and thereby impair particle strength and durability. Some schists and slates in particular are thinly laminated and tend to assume flat slabby shapes that lack strength-and do not pack well. Any or all of these rock types may be rendered undesirable because of harmful exterior coatings. Weathering processes, particularly the action of ground waters, deposit these coatings. The most common coatings are calcium carbonate, clay, silt, opal, chalcedony, iron oxide, manganese oxide, and gypsum. Particles with these coatings are undesirable as aggregates because the bond between particle and coating may be weak, and decreasing the strength of the aggregate-cement bond.

Jan 1, 1994

By James Stewart

"THAT WHICH WE CANNOT SEE" INTRODUCTION Often it has been stated that the greatest of all fears is fear itself - fear created only by that which we cannot see or by that which we fail to understand. The elimination or minimization of fear can best be accomplished by a thorough understanding of the underlying causes of the fear. As related to the mining industry the omnipresent fear is the dread of acquiring cancer through accumulated exposure to "that which we cannot see" - radioactivity. The understanding of the resulting exposure effects can best be obtained through acquisition of authentic data and the subsequent analysis of the same by a group of highly qualified specialists. I may point out that the nuclear industry and its source, uranium mining, greatly surpass any other industries in the degree of public awareness as to its potential environmental effects. Public out-cry has always influenced major decisions relating to how industries conduct their operations and much of their effort has resulted in many changes. The issues of health and safety in the mining industry have created considerable public concern, but intense concern to those of us directly involved within the industry. Increasing concern regarding the effect of human activity on the quality of the outer environment of air, land, and water has developed within the past two decades. There is now a growing concern about the health and safety of persons at work in their inner environment, of their working-places in industry. Hearings and investigations conducted in Canada by three appointed "Royal Commissions" have all confirmed that this concern is well justified when focused on the health and safety of workers in our mines. REGULATORY CONTROL OF URANIUM MINING OPERATIONS In Canada, the ownership of mineral resources and the control of their extraction, except for uranium, is vested under the "British North America Act" in the provinces. In all provinces the statutory basis for health and safety provisions in the mining industry can be found in the provincial "Mining Acts" with each province assuming the responsibility to produce its own "Mining Act". In particular, all of the Mining Acts in Canada place upon the management of a mine the responsibility to ensure that provincial provisions are met. The "Federal Register" and mining companies parallel this arrangement in the United States. Equivalent legal

Jan 1, 1981

By J. E. Gebhardt, S. Chander

Significant advances have occurred in the use of electrochemical techniques for sulfide mineral flotation research. The techniques have been used singly or jointly with other characterization methods. When used in combination with other methods, the electrochemical methods provide a means to control the state of oxidation of the surface. Various analytical methods are employed for characterization. The methods that have been used include wetting, x-ray photoelectron and fourier transform infrared spectroscopies. The electrochemical methods include voltammetry and transient electrochemical techniques of galvanostatic polarization and AC impedance spectroscopy. The challenge for the future lies in the utilization of this knowledge in plant operations so as to increase the overall efficiency of flotation separations.

Jan 1, 1989

By J. R. Batista, J. C. Young

Leachates from gold heap-leaching mines may contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina from relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for a full-scale activated alumina process. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH levels greater than 5.0. At pH levels less than 4, silica was poorly adsorbed by alumina, and selenium adsorption was improved. Silica adversely affected the selenium adsorption capacity.

Jan 1, 1998

By T. P. Meloy

Media mills operate by having energy transferred to the media which in turn grinds the feed material in a packed bed. Regardless of the mill type, the media energy density per unit surface area is constant. Since for optimum grinding conditions, both peak pressures and particle number of the bed depth are constant, the frequency of energy input is inversely proportional to feed size. As the particle size decreases the voles energy density increases linearly necessitating cooling in stirred mills. Grinding finer particles therefore, requires moving from rotary to vibratory mills, and the finest, the stirred mills.

Jan 1, 1987

Stratabound uranium deposits consist generally of two comingled geologic and statistical populations. Barren zones, usually having radiometric assays too low for recording on digitized logs, comprise a large portion of a mineralized stratum. In between are mineralized zones; where the grades are distributed essentially lognormally. Estimation of open-pit ore reserves requires the prediction of the tonnages of selective mining units (the smallest mined volume which may be segregated as ore or waste) and their grades within panels of convenient size for open pit planning and economic analysis. The proportionate tonnage of mineralized selective mining units within each panel can be predicted by kriging an an indicator function assigned to each composite (1 if mineralized, 0 if barren). Next, using logarithms of mineralized assays, the conditional lognormal distribution of grades of mineralized selective mining units can be found. Using this distribution and the krigedestimate of the probability a selective mining unit is mineralized, the grade and tonnage of selective- mining units above any cutoff can be predicted. A case study illustrating this two- step procedure is presented for the Imouraren uranium deposit located in the Republic of Niger. Using cross validation, the estimation procedures were checked and were shown to be adequately accurate for mine planning purposes.

Jan 1, 1979

By Jon P. Stone

The Automated Minerals Information System (AMIS) is an integrated data base system being developed to support the Bureau of Mines minerals information collection and analysis activities. The system facilitates cross-referencing and integration of domestic and foreign information from a variety of sources. The AMIS provides a central source of minerals information that is versatile and responsive to the needs of problem and policy analysts as well as supporting the needs of those involved in data collection and interpretation. As the AMIS becomes fully implemented, it will become an important tool in forecasting and assessing the impact of policy decisions that affect the supply and demand for minerals. The Bureau of Mines has long been the Federal Government&apos;s principal source of worldwide information on non-fuel minerals. Emphasis is placed on the analysis of mineral problems and policies as they affect the world&apos;s nonfuel mineral resources. To facilitate timely and accurate analysis, comprehensive data on 87 commodities are collected by various Bureau programs. Minerals information is made available through a number of periodic publications including the annual Minerals Yearbook and monthly Mineral Industry Surveys. These data collection and analysis activities have traditionally been supported by over 200 separate information processing systems. The Bureau of Mines has begun to implement a broad information strategy to provide a better response to the mineral problems and issues of the 1980&apos;s. The cornerstone of the Bureau of Mines information strategy is the development of the Automated Minerals Information System. When fully operational, we believe that the AMIS will provide the Bureau of Mines with the most comprehensive source of minerals information available anywhere in the world.

Jan 1, 1982