Search Documents

By Christopher Mark

The Bureau of Mines has recently completed a comprehensive study of coal strength. More than 4000 individual test results from over 60 seams were extracted from the literature and combined in the most complete data base of the uniaxial compressive strength of coal ever assembled. In addition, more than 100 case studies of in-mine pillar performance were available in the Analysis of Retreat Mining Pillar Stability (ARMPS) data base. Statistical analysis of this wealth of data has yielded valuable results. The data shows clearly that the "size effect" is related to coal structure. The widely-used Gaddy formula, which predicts a significant strength reduction as the specimen size is increased, was found to apply only to "blocky" coals. For friable coals, the size effect was much less pronounced or even non-existent. Case histories of failed pillars are the best available data on in situ coal strength. This study found no correlation between the ARMPS stability factor of failed pillars and coal specimen strength. Pillar design was much more reliable when a uniform coal strength was used in all case histories.

Jan 1, 1996

By G. R. Corbett

The introduction of roof bolts to Phalen Colliery in the Sydney Coalfield, Nova Scotia (annual output of 2Mt) has been successfully implemented in maingate and tailgate entries over the last four years. Monitoring of the roof bolted areas continues to be an integral part of the quality control program as the results are utilized to maintain safety and to aid in long-term design strategies. Although all gateroads in the Phalen Colliery have converted to roof bolts as their primary means of support, the majority of intersections which intersect the main slopes remain supported by large steel structures. Several intersections within the Phalen Colliery were monitored as they were created by the mining process. A comparison is made between intersections supported with only traditional 6.4 to 6.7 m steel structure and intersections supported by 2.44 m fully resin encapsulated roof bolts in conjunction with 7.6 m fully cement grouted cable bolts. Detailed monitoring was conducted using CA NM ET's intrinsically safe sonic probe extensometer datalogger which has the ability to read up to sixteen probes simultaneously at programmed intervals. The density of the data from the datalogger has allowed a better understanding of the deformation of cable bolted intersections than was possible with manual monitoring. Test results have helped mine operators to design safer cable bolted intersections.

Jan 1, 1995

By Dwayne C. Kicker

This paper introduces the concept of design theory and methodology as applied to rock mechanics for more innovative and efficient design. This is a "frontier" research area in rock mechanics because although design is a fundamental foundation to all engineering branches, very little attention has been paid to this aspect in mining. In discussing the theoretical premise of design, this paper identifies the principles which form the basis of design activity. Also, from a practical viewpoint, the findings from a series of interviews with mine design engineers are presented. These findings lead to the identification of needs arising from overlooked design methodology in practice.

Jan 1, 1989

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

Appropriate roof control is the most important requirement in underground coal mining and, in the case of longwall panels or second mining in room and pillar extractions, this can be simply expressed in terms of good and predictable roof caveability. Studies of roof caveability have been undertaken in many coalfields around the world. Most of their conclusions. however, are directly related to the mining and geological conditions experienced in these areas and as a result, may not be applicable to the conditions encountered in the Appalachian coalfield. Furthermore, some of these studies appear to be theoretical and conceptual, ignoring many important parameters of the geological environment, whereas others rely heavily on geological information but lack a rigorous foundations upon which quantitative design guidelines can be built. The objective of this study is to analyze caving and mass deformation characteristics above longwall panels in Appalachia and includes: - Analysis of the effects of the geological and geomechanical characteristics of the strata on the caving height and the bulking of the caved-material. - Testing of the applicability of the various theoretical and empirical models of roof caving. Formulation of a numerical around- deformation model for ion-elastic material behavior.

Jan 1, 1986

By Frank E. Chase

Clay veins, also referred to as clay elastic dikes, have been responsible for numerous underground injuries and fatalities. These hazardous structures are also responsible for increased production costs during all phases of mining. For these reasons, the Bureau of Nines has investigated the physical characteristics of and roof instability problems associated with clay veins in order to make support and other mining recommendations. In addition the occurrence and origins of clay veins were examined to determine whether or not the structures could be projected into unmined portions of the coalbed. This investigation included portions of the Arkoma, Illinois, Northern Appalachian, Southern Appalachian, and Uarrior Coal Basins. Virtually a11 clay veins observed or documented occurred in the Illinois and Northern Appalachian Basins. Observed clay veins ranged in sire from 1 inch to 16 feet In cross-section and were found under shale, siltstone, sandstone, and limestone roof rock. Individual clay veins were predominantly composed of claystone; however, limestone. siltstone. and sandstone infilled clay veins do occur. Clay vein formation has been associated with the infilling of fissures which result from compressive, tensile, or shear ground failures. These gaping fissures were propagated by compactional processes and/or tectonic stresses active during and subsequent to coal iff cation. Associated fault, fracture, and slickenside planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance the roof is segmented into cantilever beams causing unstable conditions. Therefore, the strata on either side of the clay vein must be bolted and strapped together to form a beam.

Jan 1, 1984

By H. J. Siriwardane

This paper presents results from three case studies involving longwall mine panels at which the measured ground movements were compared with the numerical model predictions based on the finite element method. A new approach called the "displacement approach" was used in this study. The general concept of this method is based on the assumption that total roof collapse occurs behind the mine face as it advances. This assumption appears to be true for almost all longwall mining conditions. The prediction based on the numerical model appears to compare well with the measurements.

Jan 1, 1988

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By Jeffrey M. Listak

This report describes a study, conducted jointly by BethEnergy Mines Inc. and the Bureau of Mines, to assess the effects of longwall front abutment loading on various supplemental support materials utilized in a predriven recovery room. The purpose of the predriven recovery room is to reduce longwall equipment transfer time by eliminating the premove preparation associated with conventional recovery methods. In addition, the room provides a large area in which face salvage equipment can maneuver. Results of four recovery-room study areas show the progression and influence of the front abutment on the longwall panel and supports and their subsequent behavior. The best performance (i. e. the support that most facilitated recovery) of support material was achieved through the use of a concrete mixture which had a sand content of 35 percent by volume. The longwall transfer time was reduced by 30 percent which translates to a production advantage of 37,000 raw tons of coal per panel.

Jan 1, 1989

By Kausik M. Sinha

Hydraulic stowing, which is being practiced in several major coal producing countries to deal with adverse mining conditions, usually permits almost 100% coal recovery from underground mines with minimal and controlled surface subsidence. It can be implemented in the US coal mines to reduce the severe effect of land subsidence and at the same time improve the cost of coal production, both of which are major setbacks for the coal industry in the USA

Jan 1, 1989

By Stephen C. Tadolini

The U.S. Bureau of Mines, in cooperation with the Cyprus- Plateau Mining Company, has conducted research to provide an alternative to traditional secondary support systems in a two-entry, yield pillar gate road. As recent as two years ago, it was impossible to imagine a gate road supported solely with internal high-strength resin-grouted cable supports that would virtually eliminate the necessity for crib or concrete external supports. The support system evaluated consisted of 1.6-m (5-ft) full-column resin-grouted bolts and 4.8-m (164) long cable supports installed in conjunction with wire mesh and "monster-mats." Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during first and second panel extractions. The stress and loading histories for the panels and yield pillar were monitored to evaluate the stress transfer and pillar performance in conjunction with the roof and floor behavior. The test results indicated that the designed support system successfully maintained the roof during the extraction of two longwall panels and dramatically reduced the cost of secondary support. This paper will describe the theory of a cribless support system, the advantages of cable supports, and present the pillar, roof, and floor measurements made to assess the support performance during longwall retreat mining.

Jan 1, 1995

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By M. Craig Miller

As the trend continues in the U. S. toward inceased capital investment in longwall mining equipment and wider panels. the risk also increases for gotential financial and production loses due to undetected geologic anomalies. This paper describes how RIM Sm (Radio Imaging Method) is utilized in conjunction with more traditional exploration and interpretive methods to delineate fluvial channels. displacement faults and poor roof conditions in a Southeastern Ohio coal mine

Jan 1, 1990

By Danell. R. E.

A drill monitoring system has been developed which measures performance characteristics of a rotary drill and relates this to the material strength and rotary specific energy. The drill monitor is computer based and is used to produce a profile of the relative in-situ material strength as a function of depth. This information has been used in determining the placement of explosive in selective loading of blastholes and estimating the amount of lump product in a particular section of an ore body.

Jan 1, 1989

By L. J. Lorig

Much of the present knowledge about caving behavior of rock masses has been obtained from empirical observations. Additional notions about caving have been developed through inferences derived from two-dimensional finite element analyses. These analyses have indicated that a combination of one low-angle set of fractures and one nearly vertical set of fractures is the optimum fracturing configuration for ease of cavability of an orebody. This paper presents the results of two- and three-dimensional distinct element analyses which draw different conclusions than those reported from finite element studies. The distinct element method is selected far analysis of cavability because this method treats the rock mass as an assemblage of rock blocks which may interact individually, The results of the analyses are compared to a documented case history which involved a groundfall of 80,000 tons of ore in a 160-foot high pillar. The mechanics associated with these results are-explained in terms of simple static stability analysis of wedges. The propensity for orebody caving is primarily a function of the number of joint sets or potential "release" surfaces in the orebody. This mechanism is influenced by the bounding weak discontinuities, and intact strength of rock material.

Jan 1, 1989

By Erdal Ünal

The computer program introduced in this paper is based on design guidelines developed for selection of support systems used in mine roadways. The support types considered include rock bolts as well as rigid and yieldable steel arches. Using the computer program, the design engineer can select the type, pattern and specifications of the support systems suitable for various roof conditions. The concepts utilized, assumptions made, support selection criteria and description of the computer program, developed for the PC, are included.

Jan 1, 1989

By Keith A. Heasley

In the past, numerous displacement-discontinuity (DD) models of stratified rock masses have been proposed using a homogeneous isotropic elastic overburden. In this paper, it is postulated that a laminated overburden model might be more accurate for describing the displacements and stress in these stratified deposits. In order to investigate the utility of using a laminated overburden in a DD model, the fundamental mathematical basis of the laminated model is presented and graphically compared with the fundamental behavior of homogeneous isotropic elastic overburden and with field data. Specifically, the stresses and displacements surrounding an idealized longwall panel as determined from the laminated overburden model are presented and compared with results from the homogeneous isotropic overburden and with measured abutment stress data. Also, the remote displacements and surface subsidence as calculated by the laminated overburden model are compared with homogeneous isotropic calculations and with measured subsidence data. The results of this investigation show that the laminated overburden is more supple, apt to propagate displacements and stress further, and better able to fit observed data than the classic homogeneous isotropic overburden. Ultimately, it is suggested that the laminated model has the potential to increase the accuracy of displacement and stress calculations for a variety of mining situations.

Jan 1, 1996

By Peter Cain

In response to the appearance of excessive convergence of bolted gateroads in the front abutment zone of retreating coal faces at Phalen Colliery, staff from the CANMET Cape Breton Coal Research Laboratory in Sydney, N.S. initiated a programme of roof profile measurements in the front abutment zone of longwall headgates. The results of these measurements allowed a characteristic deformation curve to be determined for each headgate, and the early identification of areas showing an unstable deformation trend. These areas were then reinforced with supplementary support. The monitoring programme was adopted and enlarged by the rock mechanics staff of the Cape Breton Development Corporation, and has been continuing for a period of approximately two years. A sufficient quantity of data now exists to be able to make an assessment of the effects of a number of mining parameters on the performance of the gateroad in the front abutment zone. The following paper describes the method of measurement, illustrated by typical results, and goes on to relate variations in rate and patterns of movement to geology, interaction, method of support and pre-mining stresses.

Jan 1, 1996

By Miklos D. G. Salamon

If all stratifications are horizontal, the computation of surface deformation induced by coal mining involves the prediction of roof and floor convergence and then the transfer of the effects of this relative displacement to the surface through the use of the appropriate influence functions. A laminated model, in the form of a quasi- continuum, provides a simple means of computing the approximate convergence distribution and leads to the Gaussian distribution as the influence function. The ideas presented in this paper represent a subtle but fundamental generalization of the influence function Method. It is postulated that the influence of a small area of extraction is proportional to the roof and floor convergence and not to the thickness extracted. This difference in definition removes many conceptual difficulties associated with the influence function method. To demonstrate the utility of the model, the surface disturbances induced by the extraction of a parallel sided long panel are derived. Formulae giving subsidence, tilt, horizontal displacement and strain are given.

Jan 1, 1989

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986