Search Documents

By Gift Makusha

The Witbank Coalfield in South Africa contains up to five economically viable coal seams. These seams have been mined continuously for over 100 years and the reserve in now becoming depleted. The normal mining method has been bord and pillar with examples of stooping. The situation now occurs where the formed pillars, left to maintain stability, have a higher quality than the coal that is left in the unmined reserves. Where the reserves are less than 70m deep and continuous over several kilometers, opencast mining is being successfully applied. After several years of investigation, Anglo Coal has identified blocks of coal that warrant investigation with regard to pillar extraction by underground methods The proposed method is pillar extraction using Mobile Roof Supports (MRS) It is proposed to mine three panels at a depth of 120m, by keeping the panels narrow and sub-critical. The sub-critical layout does not allow caving to surface and more stress is thrown onto the barrier pillar rather than the face pillars. The sub-critical span is anticipated to be 100m. The paper describes the full geotechnical investigation, including numerical modelling, instrumentation and drawing on the local South African experience of shortwall mining. The project will be unique in that pillars were not designed for pillar extraction and have low factors of safety (l.4 - 1.8) and width to height ratios of less than 4. The mining height will be approximately 4-4 5m, and this represents "new" operating heights for Mining Roof Supports. The required equipment was ordered in late 2002 and pillar extraction is anticipated to begin in June 2003.

Jan 1, 2003

By B. (Mamas) Das

A project to evaluate the suitability of point Load strength tests for testing and classifying coal measure rocks for coal mining application was initiated by Canada Centre for Mineral and Energy Technology (CANMET). A summary of this study with emphasis on the important findings is presented in this paper. The instrument as used in this study is a Robertson Research Rock Strength Index Log. Because of the variation in the correlation ratio between uniaxial compressive strength and point Load strength index for hard rocks and soft rocks it was decided to establish this corre¬lation initially on cement concrete specimens specially prepared for this purpose following ASTM specifications. These specimens are expected to represent soft rocks and at the same time would be of uniform quality. Once a general trend of this correlation was established tests were performed on coal and rock samples from the sub-bituminous and bituminous coalfields in Canada. The most important results may be stated as follows: (i) Generally, the common value of the ratio between the uniaxial compressive strength and the point load strength index ranges between 8 to L4. (ii) The Robertson Research Rock Strength Index Log proves to be quite suitable for testing sandstone, siltstone and some coals from the bituminous coalfields but problems have been experienced when testing weathered samples or samples from the sub-bituminous coalfields. (iii) In some cases tests were successful if Larger samples from weathered zones or from sub-bituminous coalfields were used. However, a magnified load gauge for 0-3KN or 0-5KN is expected to be the best solution for soft and weathered rocks in most of the cases. Some mudstones and some rocks from weathered zone do not appear to be suitable for these tests. This aspect of the study is still under investigation. (iv) Deterioration of rock properties due to weathering has been determined through tests on samples collected from weathered and unweathered samples.

Jan 1, 1984

By Krzysztof Tajdus

In Europe, horizontal strain is a primary parameter for estimating building hazard resistance. Other measured indices, like curvature, are less important, since in most cases of European excavation depths are very large (about 1,000 m (328 ft)) and, in such circumstances, curvature influence decreases. Therefore, a proper description of horizontal displacement (and strain) in the scope of minimizing influence is essential. This article presents a development of European methods of horizontal displacement and horizontal strain calculations, as well as current solutions in this respect.

Jan 1, 2011

By Keith A. Heasley, Jian Yang

"LaModel uses a laminated overburden boundary-element model and can calculate not only seam-level stresses and displacements but also surface subsidence for thin tabular deposit such as coal seams (Heasley, 1998). Up to this point in time, the material property wizards in LaModel have primarily been designed for calculating accurate stress distributions in single- and multipleseam situations, and for investigating and optimizing pillar sizes and layouts in relation to overburden, abutment, and multipleseam stresses. However, the critical input parameters that will give the most accurate seam-level stress distribution do not necessarily produce the best surface subsidence prediction. The objective of this paper is to develop a methodology for calibrating the critical input parameters in LaModel to optimize surface subsidence prediction.For optimum surface subsidence prediction, it was found that the gob convergence (as defined by the final gob modulus) and the overburden stiffness (as defined by the lamination thickness) were the two most critical parameters that needed to be calibrated (Heasley, 2016). By calibrating numerous panels with various widths and depths, a formula that provides the optimum final gob modulus to use for subsidence prediction was developed. Also, three different empirical formulas for optimizing the lamination thickness as a function of overburden depth and/or the panel width to- depth ratio were determined for the three cases: supercritical panels, and subcritical panels with and without offsets. Further, if the user has measured data for subsidence factor and angle-of draw, the optimum final gob modulus and lamination thickness can be determined from the measured data. These new subsidence prediction formulas are being implemented into new material wizards in LaModel.INTRODUCTIONIn the past few decades, with the increased need for highly productive mining techniques, full extraction mining methods have been increasingly employed in the U.S. coal mining industry. These total extraction mining methods, which include both longwall mining and room-and-pillar retreat mining, normally cause immediate roof caving and the associated surface subsidence. These methods can be highly productive and cost-effective, but the associated surface subsidence can cause damage to surface structures and negatively impact the surface environment (Peng, 2008). Therefore, a reliable program for predicting the surface subsidence associated with full extraction mining is required for appropriately engineering and managing the surface subsidence impacts of full extraction mining."

Jan 1, 2016

By George S. Kalamaras

Coal strata strength is included as a vague term in most of the pillar design formulas, either as a questionable fraction of the intact coal strength or a size-dependent relationship for scaling down a laboratory value to the in situ strength. In order to introduce a coal mass strength criterion which would be compatible with current design trends, the Rock Mass Rating (RMR) system was revised to incorporate factors governing coal seam behavior under load. A number of adjustment factors have been proposed but, the most significant change, is the introduction of a parameter representing the heterogeneity of the seam. When developing a rock mass strength criterion, it is necessary to find the constants of appropriate intact rock strength criteria and to establish a correlation to scale down these constants as a function of the RMR. For four intact rock strength criteria, the constants for coal were found using the Nelder-Mead method. To correlate the constants of the strength criteria with the coal seam quality values (RMR), a procedure was developed based on finite element modeling of in situ large scale tests for which the RMR was known. A new coal strata strength criterion is proposed, in a principal stress formulation, for modeling coal pillar behavior when the stress field in a pillar is known. A linear relationship is also given, to be used when empirical pillar strength formulas are used to design pillars. The proposed criteria have been evaluated in a case study.

Jan 1, 1993

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993

By G. K. Rogers

Portals, which are the surface entrances to underground excavations, are frequently overlooked and often difficult areas In terms of ground control. Failures commonly occur In the typically high angle approach cuts and Initial subsurface portion of the portal. In order to permit rigorous design of all types of portal structures, failures are Identified and subsequently classified. Based on the failure classification and suggested analysis methodology, optimum ground and support loading can be determined.

Jan 1, 1988

By Mohummad Akram

Statistical analysis of multi-seam mining case studies demonstrated that geologic structure and lithological type and sequencing were predominant factors in entry failures. Finite element analysis was used to evaluate the effects of stress field changes on entry instability under differing geologic conditions. Analysis showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Effects of external support on roof stability were examined. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research design, criteria were developed for roof stability evaluation under specified interactive loading conditions.

Jan 1, 1993

By Jim Galvin

4 and 6 point timber chock constructions are used extensively on both a systematic and spot basis by Australian longwall operators to support tailgate roadways. In 1996, the School of Mining Engineering at UNSW published design and performance criteria for timber chocks constructed from Australian hardwoods. The research was funded by the Australian Coal Association Research Program (ACARP). In 1997, ACARP awarded funding for a stage 2 testing program. This testing focussed on examining the effect of using thinner timber elements in chock constructions to improve OH&S and comparing the full-scale performance of traditional 4 point chocks to Link-n-Lock constructions. It was established that chocks constructed from thinner elements have failure loads much less than thicker elements. However up to the failure loads of the thinner elements there was no significant difference in the response to convergence of chocks constructed from 25, 50 or 100mm thick elements. Chocks constructed from 150mm thick elements have a similar ultimate strength to the 100mm thick elements. However, they have a significantly lower resistance to load, thereby permitting more convergence to occur. There is more potential for chocks comprised of thin elements to be constructed 'out of plumb' and so suffer eccentric loading. The full scale testing program established that at any given level of convergence up to 10% strain, the timber in a Link-n-Lock chock generates twice the support resistance of the same quantity of the same timber in an equivalent size 4 pointer chock. On the basis of support resistance per cubic metre of timber, there is only a marginal difference in the performance of 1.0m Link-n-Lock chocks and 1.2m Link-n-Lock chocks constructed from select Blue Gum. The cost per tonne of support provided by a Link-n-Lock chock is effectively half of that provided by a 4 pointer chock of equivalent dimension and timber. Up to a strain level of 4%. Link-n-Lock chocks constructed from 1.2m long elements are slightly more cost effective than the same chocks constructed from 1.0m long elements. Thereafter, there is no significant difference in cost per tonne of support resistance. Beyond a strain level of about 4%, Link-n¬Lock chocks constructed from landscape grade Blue Gum are just as cost effective as Link-n-Lock chocks constructed from structural grade 4 Blue Gum.

Jan 1, 2000

By A. Bortolussi

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables an tool performance (cutting rate and bead wear) has been elucidated.

Jan 1, 1992

By John Ellenberger

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

Jan 1, 2003

By James G. Schotsch

Unmapped abandoned mines are hazards for under¬ground mines, surface mines and surface structures. The Radio Imaging Method (RIM) provides a cross borehole technique to remotely detect abandoned mine works. RIM was used at the Buck Creek Mine, an underground coal mine, to determine the extent of unmapped mine works. The information provided by the RIM survey assisted the mine planners in developing their mine.

Jan 1, 1990

By Stanislaw Prusek

The present state of Czech and Polish coal mining industry is presented at the beginning of the article. This paper will inform the reader of the general data concerning hard coal reserves? number of mines, number of miners, output, number of longwalls, productivity, depth of extraction, and extraction methods?in both countries. The main part of the paper describes the methods of gateroad development as well as gateroad support characteristics (support types, gateroad shape and dimensions, distance between support sets, types of reinforcements). The development prospects of gateroad support in the Czech and Polish coal mining industry are also presented.

Jan 1, 2011

By John Stankus

Regional high horizontal stress has long been recognized as an important factor affecting roof stability However, localized high horizontal stress, although causing many ground control problems, has not received due attention, Through many ground control studies and underground experiences, it has been round that localized horizontal stress can be created by abrupt changes of overburden and stream valleys. The magnitude of localized horizontal stress depends on the valley configuration and overburden depth. Utilizing the Jennmar Finite Element Analysis System (JFEA), this paper analyzes the mechanism of the localized horizontal stress concentration based on two cast studies.

Jan 1, 1999

By Michael Gauna

Ground fall injuries and fatalities in United States underground coal mines have shown a diminishing trend. Advances in bolting and standing support systems have led to improved safety in underground coal mines. However, the Crandall Canyon Mine disaster in 2007, in which 9 individuals were fatally injured as a result of a widespread collapse, emphasized that proper mine design is a critical issue that must be addressed. The Mine Safety and Health Administration (MSHA) has instituted technical review procedures structured to facilitate the implementation of safe mine designs in underground coal mines. The technical review process and the typical information required are outlined in this paper. The range of mining situations that lead to a technical review, common design methods submitted for review, and their relevant guidelines and limitations are also discussed. Additionally, the relationship between design criteria and mine site historical experience is discussed.

Jan 1, 2011

By Vincent Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2002

By John K. Wood

The development of an expanded cement product represents a major advance in the technology of roof control systems. Such a product is gaining recognition as a valuable tool in today's cost- conscious coal mines. The National Coal Board's Bretby Research Lab, in conjunction with Polement Ltd., developed the first lightweight cement for use in the mines of the United Kingdom. The product, Aqualight, is a low-density (about 12.5 PCF) cement with a typical compressive strength of about 19 p.s.i. The final product increases in volume by approximately 15 times its dry powder volume. Aqualight gels in about 2 minutes, becomes self-supporting in 15 minutes, and fully cur& in 24 hours. When subjected to a load, the "cells" within its bubble structure collapse so that the product gains in density and compressive strength while retaining its integrity. Traditional methods to contain and support roof fall cavities through cribbing and blocking are both dangerous and labor-intensive. Aqualight represents a significant advantage over such traditional methods. It is non-toxic, non-cmbustible, and very easy to install. Aqualight can be pumped to the worksite from re- mote locations (as much as 600 feet), thereby reducing danger to men and equipment. Addition- ally, the strength of the cured product can be varied by adjusting the expansion ratio and resulting density. A compressive strength of 150 p.s.i. can be obtained in this manner. Although primarily designed to fill cavities resulting from roof falls. Aqualight has found a wide range of applications in mining industries around the world. In addition to cavity- filling, Aqualight has been used for ventilation stoppings, fire stoppings and emergency fire control, backfilling between arches and the roof and ribs, and backfilling of old workings. Since its recent introduction into the United States. Aqualight has been used by MICON SER- VICES, INC. to fill several roof fall cavities along headgate entries. In all cases, the cavities were contained and the longwall moved through without problems. Roof Pall cavities along main haulage entries and at shaft/slope bottoms have been successfully filled. MICON has also installed Aqualight as backfill material around arches. A current major project is the installation of trial ventilation seals using Aqualight as an alternative to traditional block and mortar construction. Pending MSHA approval, MICON anticipates the use of Aqualight in the construction of both ventilation seals and stoppings. In addition to new construction, Aqualight can be employed to repair stoppings damaged by roof convergence and floor heave. In labor savings alone, this is very attractive for remote stopping repair. Among the many other uses of Aqualight is the backfilling of old auger holes, which will support the highwall and allow access to coal re- serves which are presently sterilized.

Jan 1, 1986

By Sun Henghu

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed. The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by excess water drainage under the ground are resolved.

Jan 1, 1992

By Thomas M. Barczak

Wood cribs are used extensively to stabilize mine openings by providing resistance to deflections of the immediate roof and floor and by supporting the weight of unstable rock masses. While the unit costs of these supports are relatively low, their extensive use results in significant costs to coal mining. The Bureau of Mines has developed a model that computes the load capacity of wood cribs as a function of the displacement of the crib structure induced by mine roof and floor convergence. This permits comparison of the loading characteristics of various crib constructions and enables systems to be designed with consideration of the load conditions imposed by the mine environment. The design method matches the stiffness, strength, and stability of the crib structure with expected rock mass behavior to determine a crib design and employment spacing that will provide the lowest cost support.

Jan 1, 1993

By Holger Witthaus

The conditions of great mining depth and multi-seam¬longwalling require a special method of rockbolting, It can be described as a control loop which is based on the elements of planning, drivage and measurement. Different planning elements such as the results of the observation of physical models, numerical programmes for calculation of stress-distribution and support success, lab and underground support testing and the knowledge of strata behaviour underground including geotechnical classification are used to get best results. The increasing geotechnical information collected during drivage of roadways are used to estimate and minimise the risks of support-overload. The repeated plan/acutal comparison during the use of roadway and continuously monitoring of support and roadways provided the opportunity of optimising support design during the process of drivage and if necessary in front and after of the longwall face.

Jan 1, 2000