Search Documents

By Joshua Hescock, Zach Agioutantis

"The Surface Deformation Prediction System (SDPS) has been developed as an engineering tool for the prediction of subsidence deformation indices through the implementation of an influence function. SDPS provides a reliable and fast method for the prediction of mining-induced displacements, strains, tilt, and so forth at any elevation between the seam and the horizontal or varying surface topography. One of the key aspects in obtaining reliable ground deformation prediction results is the determination of the edge effect offset. The value assigned to the edge effect corresponds to a virtual offsetting of boundary lines delineating the extracted panel to allow for roof cantilevering over the mined out area. The objective of this paper is to describe the methods implemented in updating the edge effect offset code within SDPS. Using known geometric equations, the newly developed code provides a more robust calculation of the offset boundary line of the extracted panel for simplistic, as well as more complex, mining geometries. Assuming that an extracted panel is represented by a closed polyline, the new edge offset algorithm calculates a polyline offset into the extracted panel by the user-defined edge effect offset distance. Surface deformations are then calculated using this adjusted panel geometry. The MATLAB® program was used for development and testing of the new edge effect offset feature. In completing rigorous testing regimes, the new offset features will be integrated into SDPS, further increasing the speed and reliability of the programs resulting in a retrospective increase in capability and flexibility. INTRODUCTION Underground operations have been known to cause mining-induced subsidence inside and outside of the mine permit area (Karmis, Agioutantis, and Andrews, 2008). Additionally, subsidence can impact surface water bodies, such as rivers, streams, lakes, and wetlands (Karmis and Agioutantis, 2015; Newman et al., 2016), as well as infrastructure, such as roads, railroads, pipelines, and buildings. With an increase in regulatory focus on mining-induced impacts to local structures, the calculation of mining-induced subsidence indices has become necessary in determining potential damage and mitigation efforts. The accurate prediction and evaluation of mining-induced ground deformations is required to obtain underground mining permits due to potential impacts to nearby structures, as well as hydrogeological sources. The prediction of ground deformation indices is often a complex task due to the number of input parameters required, such as mining geometries, overburden lithology, surface topography, the rate of mining (Karmis, Agioutantis, and Andrews, 2008)."

Jan 1, 2017

By Joe McQuerrey, William Kendall, Gene Wilson

"Roof bolting is the standard for ground control in underground coal mining. Rib and truss bolting is just as important when conditions are less than desirable. As a manufacturer of roof drills, J.H. Fletcher & Co. (""Fletcher"") promotes a walkthrough design machine to protect the machine operators from rib hazards.When installing rib and brow bolts in high mined heights, the operator's natural desire is to step from under the canopy onto the drill feed mechanism. This is done to allow a better reach to the drilled hole in the rib or brow. This, of course, is not an approved or acceptable practice.The effort to improve the operators' ability to reach the rib and brow has resulted in a new boom design. The design was first shown in September 2008 at the MINExpo in Las Vegas, NV. The design incorporates a step out area towards the rib side of the machine. The step provides improved access to the mine rib and brow.Having a solid concept does not guarantee an accepted design. Operator acceptance is the goal. When the machine was first tried in the underground environment, the machine operators did exactly as requested: run the machine as supplied and suggest improvements.In the fast pace job of roof bolting, any ergonomic improvements are welcome. These improvements usually increase the operator's productivity and safety. Based on operator feedback and final evaluation with Fletcher, machine revisions were generated. When the machine revisions were completed, Fletcher again asked the operators for comments, giving the boom design an evolving path into our industry.INTRODUCTIONIt's human nature to find the most comfortable position in which to do a task, especially for repetitive tasks. Designing a machine that will withstand the rigors of underground mining is a challenge in itself. With stringent safety requirements and limited real estate, there is a constant evolution in design to converge safety with productivity. With the ongoing development of the ""Rib Access Boom,"" one more step in the evolution process has been taken."

Jan 1, 2010

By Liu Changyou

This paper analyzes experimentally the stress-strain relationship and the characteristics and variation trends of acoustic emission signals of the medium- and high-burst-prone coal/rock fracture process. The precursor and sensitive characteristics of the acoustic emissions when the burst-prone coal/rock fracture occurs were obtained. The characteristic index and the feasibility for predicting rock bursts using acoustic emissions technology were proposed. Keywords: burst-prone coal/rock, acoustic emissions, energy, prediction index

Jan 1, 2003

By Ken Mills

This paper describes the first successful use of hydraulic fracturing to induce caving events "on demand" in Australia. Moonee Colliery operate a longwall immediately below a thick conglomerate strata. This strata temporarily bridges across the extracted longwall panel to create a large area of standing goal' When this standing goat' eventually collapses, the windblast generated presents a significant hazard to men working on and around the longwall face. Hydraulic Fracturing has been successfully introduced to take control of the timing of these caving events so as to eliminate the risk of windblast injury, The longwall face area is completely evacuated during the treatment. Water is pumped into an injection point located in the conglomerate strata above the standing goat. A horizontal fracture is generated and grows outward from the in point, separating the conglomerate strata below the fracture horizon_ At some point the strata can no longer span and a goat fall is initiated. After a treatment, mining can be recommenced with the windblast hazard eliminated.

Jan 1, 2000

By William B. Beerbower

When full length resin grouted bolts were introduced into U. S. coal mines some 11 years ago, it was assumed that safety would be the primary benefit. There is ample testimony to substantiate the safety factor as an important reason for using resin roof bolts. More recently, it has been determined that many coal operators not only concur with the safety consideration but also benefit economically from the safer working conditions resulting from a reduction in roof falls. IMPROVED SAFETY Some typical roof fall reduction experiences with resin bolting follow: ? Western Kentucky Mine - Resin bolting reduced roof falls by 80%. ? Southern West Virginia Mine - Experienced 141 roof falls between 1971 and 1972. In 1973 with resin bolting, roof falls were reduced 85%. ? Western Pennsylvania Mine - In 1973 had 59 roof falls with mechanical bolts. During the same period of 1974 with resin, only 19 falls were experienced - a reduction of 66%. The overall experience with resin bolted roof support has been an average 50% reduction in roof falls. Long term, this can translate into improved worker morale. As a matter of fact, a general mine foreman at the same Southern West Virginia mine mentioned above commented that improved miner morale was noticeable following the introduction of resin bolting. HOW GREATER SAFETY CAN BE COMBINED WITH INCREASED PRODUCTIVITY IN COAL MINING OPERATIONS Experience has also shown that a reduction of roof falls with resin bolting has resulted in increased production for many coal operators. Some typical examples with mines using resin bolting follow: ? Western Kentucky Mine - Resin bolting contributed to increasing production from 7000 to 11,000 tons per day, due to a 80% reduction in roof falls. This was accomplished in part by a reduction of 50% in timbering requirements and the reassignment of three roof fall cleanup crews to coal production. ? Pennsylvania Mine - Following resin bolting introduction the section showed a 50% increase in production. ? Central West Virginia Mine - Continuous miner production averaged 6 cuts per unit shift prior to resin bolting. Reduction of cleanup time, resulting from improved roof support with resin bolting, increased production to an average of 9 cuts per unit shift. PROPERTIES OF RESIN BOLTING SYSTEMS Several of the important properties of resin bolting systems which contribute to its improved performance are listed below: ? Full length anchored resin bolts and many resin anchored, point anchored bolts provide effective resistance to changing rock strata stresses throughout their length, thereby improving stabilization of rock strata over long periods of time. ? Individual layers of rock are anchored into a single high strength beam providing excellent resistance to vertical and lateral strata movement, the most common cause of roof failure. ? Moisture cannot corrode the fully grouted bolt. ? Has twice the pull strength of mechanical bolts (See Figure 1)

Jan 1, 1982

By Dale S. Preece

In 1975 Congress passed the Energy Conservation Act to establish a U. S. Strategic Petroleum Reserve (SPR) with a capacity of 750 million barrels of crude oil. The most economic storage medium was determined to be salt caverns leached in salt domes in Louisiana and Texas. Salt caverns existed at several sites when the reserve was created. These were obtained by the U. S. Department of Energy (DOE) and used to initiate SPR oil storage. In order to meet the storage capacity approved by Congress, new caverns also had to be leached. To support the resulting design effort, finite element computer program have been used to determine the creep closure and structural stability of salt caverns. Using site specific material properties including creep models, elastic moduli and fracture data, the finite element analyses have replaced earlier empirical approaches to cavern design. This report presents results of such finite element analyses to determine the best cavern roof shape and the minium pillar to dimeter ratio. , P/D. These numerical predictions indicate that the current cavern design is safe.

Jan 1, 1984

By Yanfa Gao

Clusters of underground openings were developed around the shaft bottom of Tangshan Mine. They were deep and located in soft rock strata. After development, those openings have been subjected to considerable deformation and damages. A combined supporting method including grouting and bolting, shotcrete lining and brickwork was used. This paper analyzing the theories on which this supporting method was based. A new theory called "Disturbed Creep" was developed for deformation prediction of openings surrounded by strata subjected to stresses close to limiting or failure strength. Keywords ground pressure, deep mine, soft rock, stability control

Jan 1, 2002

By Ke Yang

"Engineering practices have shown that the skip-fault longwall mining is frequently used when faults with offsets larger than 1 Om are present. Since the skip-fault longwall mining not only reduces the recovery rate of coal reserves, but also increases the cost due to developing another setup room on the opposite side of the fault and moves the longwall into it. The coal pillar so created induced residual stress in and thus affects the safe mining of adjacent coal seams. In order to investigate the influence on panel layout and retreat by a l 6.5m offset normal fault, the similar material simulation model was constructed based on the geological and engineering conditions of No.13 coal seam in the western district of Liuzhuang coal mine employing the down-dip longwall mining. The characteristics of deformation, movement and failure of the overlying strata and abutment pressure when the face cut through the hangingwall and footwall of a normal fault were obtained. There were significant differences between the hangingwall and footwall as conformed by the equilibrium structure model. The results showed that superposition of the tectonic stress from a normal fault of large offset and that induced by mining is one of key factors that lead the severe pressure difficult to control during panel retreating from the hangingwall to footwall. Accordingly, the technical solutions for a fully mechanized mining face directly cutting through the fault are presented and optimized, and the applications of the technical solution in Panels 171301and171303 of Liuzhuang mine enabled them to complete the mining safely and efficiently. INTRODUCTIONFaults have been one of the important technical factors in underground coal mining l1-2i. Engineering practice has shown that the methods of mining through the faults depend on the seam thickness, seam dip angle, offset of fault throw, equipment height, rock strength, and advancing direction l3-5l. In the fully-mechanized longwall mining, the face normally proceeds to cut through the fault directly if the offset of the fault less than 5m, and to skip Uump) the fault if the offset is larger than 5m. In the former case, the most important problem is to efficiently control or avoid roof fall accidents (i.e., crushing, falling, pushover, and rock burst). In the latter case, the most important problem is very expensive to drive a new setup room and move the face equipment to it. The skipped coal pillar may poses problems for mining in adjacent seams."

Jan 1, 2016

By Stephen C. Tadolini

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that arc easy to handle/install under temporary or previously supported roof.

Jan 1, 2001

By Frank Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors using sedimentological descriptors, lead to an understanding of the mechanisms causing roof problems. Types of bedding plane features can be categorized into geometric, internal structures, bedding-plane markings, deformed bedding, solution structures, and accretionary structures. Factors such as encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described.

Jan 1, 2002

By Kewal K. Kohli

An investigation was performed to determine the sequence of events which caused the 1987 surface subsidence and related damage to several homes in Walker County, Alabama, USA (see Figure 1). Surface affects compared to mine maps indicated the subsidence to be mine related. However, two coal seams had been worked under this area. The upper seam, the American seam ranged from 250 to 280 feet beneath the surface in the area in question. It was mined-out before 1955 by room-and-pillar method leaving in place narrow-long pillars to support the overburden strata, and abandoned in 1955. The lower seam, the Mary Lee seam, ranged from 650 to 700 feet beneath the surface. The Mary Lee seam had been abandoned in 1966 and subsequently became flooded. The dewatering of the Mary Lee seam workings in 1986 caused the submerged pillars to be exposed to the atmosphere. Due to multiple seam mining and the fact that workings had been inundated then dewatered, a subsurface investigation ensued to determine the sequence and ultimate cause of surface subsidence. Core sample tests with fracture analysis in conjunction with "down-the-hole" TV camera inspections provided necessary information to determine that the subsidence started in the lower seam and progressed through the upper coal seam to the surface. Evidence from the investigation program established that dewatering of the lower seam workings caused the marginally stable support pillars and the roof to collapse. This failure triggered additional subsidence in the upper seam which broadened the area of the influence at the surface.

Jan 1, 1992

By John C. Stankus

The success of cable bolts for mine ground control have been well documented in papers presented at this conference too numerous to reference. Cable bolts have proven effective over the years mainly utilized in the form of supplemental support. Some limited work has been conducted on the use of cable bolts as primary support This work has been mainly confined to the West and the bolts utilized were of a non- tensioned type MSHA requirements for primary support have been that the bolt system he tensioned or if non-tensioned, then fully encapsulated with resin. Many operators are now interested in using cable bolts as primary support Further, despite the enormous success of cable bolts, there have been questions raised about the longevity and corrosion characteristics of the cable itself particularly for long tern applications. To improve the corrosion characteristics of cable bolts, galvanized cable has been used for some applications However. although improving the corrosion resistance of cable, galvanized cable for mine ground control does not provide complete protection under certain types of situations and mine environments. Realizing a need for a cable bolt that can be used for primary support and provides consistent installed tension, complete corrosion protection, and a fast installation, Keystone Mining Services. LLC (KMS), an affiliate of Jennmar Corporation, has developed the INSTáL CableOx system. This paper will detail the development and specifics of this system including two underground case studies

Jan 1, 2000

By E. Bane Kroeger

In underground coal mining, there is often a need for supplemental support for mine openings. In the past, one of the most common types of supplemental support was wooden posts that were installed against the roof using opposing wooden wedges. Underground, wood has the tendency to shrink from moisture loss and dislodge if not under load. Another drawback to using wood is the variability in strength between posts. Defects in the wood such as knots can cause weaknesses that often lead to premature failure of supplemental support. Many mines that install large amounts of supplemental support in certain areas of the mine such as bleeder entries in longwall mining have switched to using steel props rather than wood posts or cribbing. The reactions of steel props under loading are well- defined and there is little variability in strength between props. Steel props and can be fabricated so they can be used in a variety of roof heights without modification. Wooden posts often have to be cut to a usable length underground before installation. This adds to the installation time of the wooden posts. Steel props are more compact and can be lighter than their wooden counterparts, depending on the length and carrying capacity. Often times it is desirable to prestress the supplemental support to improve roof stability. This is often problematic and time consuming with some types if supplemental support. With these factors in mind, research was undertaken at Southern Illinois University Carbondale (SIUC) to design a new steel roof prop. Several new clamping designs were developed and prototypes were fabricated and tested in the labs at SIUC in the spring of 2003. The designs were modified and refined and the first full-size prototype roof prop was tested in January 2004. With the success of the full-size prototypes, a cooperative research program was established between SIUC and Excel Mining Systems, Inc. to further develop the new prop. Development went smoothly and the prop has performed as expected. In February 2005, SIUC and Excel entered into an exclusive licensing agreement. The prop design under license, the K-Prop, will be installed using a lightweight portable hydraulic jacking system under design that can be used to prestress the props, applying load to the roof and floor during installation. By varying the installation load, the prestress load can be varied from about 1,000 to 10,000 pounds (4.448 to 44.48 kN) and at the same time, the carrying capacity of the K-Prop can be varied from 10,000 to 100,000 pounds (44.48 to 444.8 kN). The K- Prop is composed of only 3 pieces and laboratory testing has suggested that it can be installed by a pair of workers in less than two minutes. The speed of installation of the K-Prop should significantly reduce the total installed cost for supplemental support and should provide a safer working environment by prestressing the prop, which will add support load to the roof and floor during installation.

Jan 1, 2005

By Francis Kendorski

One of the most dangerous events in underground coal mining is unexpectedly encountering water inrushes from undetected abandoned mines in the same seam. The surest and most confident method is probe drilling either from the mine or from the surface. However, drilling is expensive and may even miss the suspected mine voids entirely by drilling through pillars. Many operators rely upon one or more of several remote sensing techniques for detecting mine voids. However, mine "voids" often are not air- or water-filled open cavities, but are collapsed, rubble-filled chimneyed columns in the strata. Geophysical techniques, such as seismic reflection and refraction, electrical resistivity, magnetics, ground-penetrating radar, and others, often assume a continuous or fractured rock mass that has varying properties which provide the signatures that allow discrimination of one strata from another, or of strata from voids. However, a rubble-filled cavity has rock block-to-rock block contact throughout its volume and can still respond as a continuous rock mass with the rock blocks allowing signal transmission or mass detection, rather than a void space. Hydraulically, a rubble-filled cavity is essentially as transmissive to water as an open mine void. Thus, the problem of detecting a mine void with confidence is significantly compounded.

Jan 1, 2004

By Wenjun Ju

It's very important to determine the limitation of bed separation in entry roof in order to predict roofs stability and take some necessary precautions. Based on numerical modeling and monitoring in the field, the new concept of Limitation of Roof Layer Separation (LRLS) and its method of determination LRLS is given in this paper

Jan 1, 2001

By Axel Preusse

To detect improper deformations of a roof bolted roadway in order to reduce inner mine damages in the most early stage and to initiate suitable countermeasures if necessary, several different measurement systems were used for monitoring a roadway's stability on the hardcoal mine "Auguste Victoria" (DSK AG). In this paper the different convergence measurement procedures are described and their respective results are introduced. Subsequently the results of the single measurement methods and procedures are correlated with each other.

Jan 1, 2000

At any given lime, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes in the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

By Abdolreza (Reza) Osouli

Determining the roof stability condition of underground coal mines in the Illinois Basin is sometimes very challenging. The roof stability of Illinois mines are mostly affected by two types of shales: Anna Shale and Energy Shale. These layers are sometimes weak in parallel bedding when subjected to horizontal stresses. The roof rocks in the Illinois Basin are are typically more moisture sensitive than the other coal fields. In this study the geotechnical properties of some of the shale units as well as limestone layers will be presented. The geotechnical properties of roof rocks consist of moisture content, unconfined compressive strength, slake durability, indirect tensile strength, and point load tests (Axial and Diametral). The correlation of indirect tensile strength versus diametral point load strength as well as unconfined compressive strength versus axial point load test are explored and discussed. These correlations will help in identifying the roof mass index and planning appropriate roof control measures. This study also evaluates the application of CMRR rock mass index for an Illinois coal mine.

Jan 1, 2014

By Hai Rong

EH-4 Electrical conductivity imaging system has been playing an important role in prospecting, looking for water resource, and determining coal mine gob boundary by virtue of its significant advantages such as collection of large volume of data, light weight, fast analysis, high-precision, and low cost. However, it has little application in determining the overburden failure zone and development of water flowing fractured zone and bed separation space in complex extra thick coal seam conditions. In order to confirm the overburden failure range and evolution of water flowing fractured zone and bed separations in complex extra thick coal seam conditions the panel 63005 of Laohutai coal mine in China was selected for study in this paper,. EH-4 magnetotelluric method was used to determine the overburden failure zones and bed separations in the overburden. Theoretical analysis and numerical simulation were employed to verify the EH4 survey results. The results show that the failure height in the overburden of the three coal splits was 120m to 170m before panel mining, and increased to 150m to 220m after panel mining. The overburden failure height was on average 7.4 times the equivalent mining height in complex extra thick coal seam condition of Laohutai coal mine when the sand backfilling and fully mechanized top coal caving methods were employed. After mining of panel 63005 started, bed separations were found on the hanging wall and footwall of the F18 fault where water bodies existed. The results obtained in this research not only provide a theoretical guidance for safe mining at Laohutai coal mine but also serve as a reference for predicting and preventing water inrush accidents for coal mines under similar condition in China.

Jan 1, 2014

By Joseph Hirschi, Naga S. Y. Tirumalaraju, Aditya Mishra, Anthony (Sam) J. S. Spearing

"Primary roof support in underground coal mines in the USA consists mostly of fully grouted passive rebar or grouted (partially or fully) tensioned rebar. Research conducted at two room-and pillar coal mines in the Illinois Basin and one longwall mine in Colorado monitored the performance of these passive and active rock bolts under similar geologic and mining conditions and found no significant initial loads in either passive or active rock bolts (Spearing et al., 2011). Active rock bolts showed significant loss of initial pre-load, although the exact reasons for this were not fully investigated. Subsequent laboratory testing has also shown that in weak rock, resin creep occurs, caused by slippage of the mechanical key between resin column and rock interface. These creep tests were studied in the laboratory in an effort to quantifythis phenomenon.INTRODUCTIONResin-grouted rock bolts are the first and main line of defense to counter roof and rib falls in underground coal mines of the United States. Rock bolts are categorized as active or passive. Active bolts are tensioned during installation whilst no (or limited) tension is applied to passive bolts, which need subsequent strata movement to generate reactive loads. During installation of passive bolts, some reactive pre-load may be generated by a significant up-thrust from the rock bolter boom.The selection of active or passive bolts is critical and is mostly dependent on the conditions and properties of the immediate roof (Unrug, 2009). This decision is frequently made based on personal experience, bias, and most recently cost. Active bolts are generally used in cases of highly laminated roof rock. When active bolts are tensioned, they develop compressive forces between these layers forming a beam, which helps to stabilize weak individual layers thereby increasing frictional forces between layers and decreasing effects of horizontal stresses. The fully grouted tensioned rebar system is high in stiffness as compared to mechanical bolts and provides higher surface area of contact along the length of the bolt due to the grout, which permits it to develop a strong anchorage mechanism."

Jan 1, 2015