Search Documents

By Balladares V. Eduardo

Most of the arsenic contained in copper concentrates is removed in the gas phase during the smelting and converting processes and, according to recent environmental regulations, it is required to fix it in a solid stable form. In this regards, ferric arsenate has been reported as thermal and aqueous stable compound. Therefore, various alternatives for treating gas containing arsenic were considered in this work. From data obtained at laboratory scale on fixation of arsenic using iron oxide, a new process to treat copper concentrates containing arsenic was evaluated. The effect of temperature, oxygen potential and the sample porosity on the fixation of arsenic contained in a gaseous stream was studied, and the iron oxide converted into ferric arsenate was up to 10%. The obtained results suggest a new alternative for gas treatment with an interesting and attractive technical development. The arsenic was retained as ferric arsenate with thermal and aqueous stability, and it allows a safe disposal keeping the environmental restrictions. The kinetics parameters are used to scale up laboratory results to higher processing rates.

Jan 1, 2005

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2Si/MgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (P/M) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2JIm is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ forming process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm) and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By F. Ajersch, P: Tsantrizos, K: Shanker

"TiN films have been deposited on various substrates by a novel reactive plasma technology. In this process, a nitrogen source (NH3 or N2) and TiCl4 are reacted in the jet of a plasma torch, and are deposited onto a substrate forming TiN films at a high growth rate ( > 2µm/min). It was found that the process parameters strongly affect the microstructure, thickness, density, and growth rate of the TiN films. These parameters include source of nitrogen (NH3 or N2, N/Ti ratio, temperature of substrate, and spray distance. In general, it was found that thick and dense coatings were deposited when the N:Ti ratio was kept low, and the substrate temperature was high. Also, for the series of conditions investigated, NH3 was found to give much better results than N2•. The limitations and advantages of this technique are also discussed in this paper.IntroductionTiN is an extremely hard material and is used in many wear applications, particularly as a protective coating on cutting tools to extend their Iife(1.2). Owing to its excellent chemical stability, TiN is also frequently used as a diffusion barrier in the electronics industry for sub-micron Al/TiN/Si ohmic contact systems (3) or as a coating on high-temperature resistant alloys in gas turbine applications (4), based on its good resistance to oxidation. Other applications include decorative coatings in the jewelry industry, and specialized applications such as solar energy absorbers and transparent heat mirrors(5).TiN films can be deposited/formed using various techniques. The main techniques of deposition are CVD (Chemical Vapour Deposition) and PVD (Physical Vapour Deposition). Each of these techniques can have many variations in equipment characteristics, reactants as well as a range of process parameters (pressure and temperature). In the CVD process, TiN is generally deposited onto a heated substrate where a chemical reaction takes place. The reaction can be one of reduction(6) (e.g.: TiCI4 + 0.5N2 + 2H2 --> TiN + 4HCI), of thermal decomposition(7) (e.g. decomposition of titanium dialkylamide), or of displacement (e.g. TiCI4 + NH3 --> TiN + 3HCI + 0.5CI2)' The displacement and reduction reactions are the most common."

Jan 1, 1994

By T. Wang, R. G. Reddy

"The corrosion of stainless steel SS316L in a low melting point novel LiNO3-NaNO3-KNO3- NaNO2 eutectic molten salt mixture was investigated at 695K. After long-term isothermal dipping corrosion experiments, the SS316L samples were analyzed using scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS) to determine the topography and corrosion products. Dense and protective lithium iron oxide scale formed on the surface and prevented the SS316L sample from further severe corrosion. Therefore, SS316L is considered to be suitable construction material for solar thermal energy storage materials containers.IntroductionMolten salt mixtures have been considered as potential candidates for thermal energy storage and heat transfer media in solar energy applications. To apply the molten salt in the energy transfer process, the standard pipes made of stainless steel must be utilized to carry the molten salt mixtures in parabolic trough system of solar power production. The pipes encounter continuous flow of hot and cold molten salt every day. Thus corrosion of stainless steel in molten salt mixtures becomes extremely essential for the long-term utilization of the thermal energy storage media. The corrosion of passivity materials inside high temperature molten salt systems have been studied which gives fundamental understanding of basic mechanism about the corrosion process [1-8].The corrosion behavior of Fe-Ni-Cr alloys in an equi-molar LiNO3–NaNO3–KNO3 mixture was studied [9]. According to the XRD analyses, the major phases in the oxide scales were identified as LiFeO2, Fe3O4 and Cr2O3. A HITEC® salt mixture (NaNO3–NaNO2–KNO3) was also tested as a corrosion medium for stainless steel [10] and the corrosion rate was found to be affected by the protective oxide layer. In most cases, the alloys having more than 10wt% chromium show high resistance to corrosion in molten salts."

Jan 1, 2014

By I. D. Reznik

Regularities of cobalt and nickel distribution between slag and matte, slag and metallic alloy on the base of concepts on exchange reaction equilibrium are considered. It is shown that the distribution of cobalt and nickel in industrial processes approaches to equilibrium one. Oxysulphiae influence on the bahaviour of cobalt, nickel and sulphur is shown. The recommendations on conduction of the processes of smelting, converting and slag cleaning based on the analysis of the methods or" non : ferrous metal separation from iron are given.

Jan 1, 1993

By Konstantina Chalastara

Mixed phase titanium dioxide (TiO2) nanoparticles synthesized through hydrolysis of TiCl4 solution at different conditions, namely concentration, pH, and residence time are characterized and evaluated as photocatalysts. The process is operated in a continuous stirred-tank reactor, CSTR giving blends of anatase, brookite, and rutile nanoparticles that were further evaluated to find the optimum mixture for a photocatalytic sorption material. The titania nanoparticles are first characterized in terms of photocatalytic activity under UV light illumination using an organic model compound (methyl orange) and after that are tested for removal of toxic selenate and selenite species from simulated effluent waters.

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By Maurizio Marezio Bertini

Ammonia - ammonium sulfate solutions were sparged in a glass reactor with a SO2/O2 gas mixture (2% SO2 and 98% O2) to leach copper from pure chalcopyrite and chalcopyrite concentrate. The SO2/O2 mixture produces higher and faster extractions than O2 by itself. The effect of temperature, particle size and free ammonia concentration was investigated. The fastest and highest recoveries were obtained at 80 oC from a chalcopyrite concentrate with a d80equal to 13 m, with about 83 gpl free ammonia, an average pH equal to 8.75 and a stirring speed of 500 rpm. The extraction process was controlled by diffusion through a product layer, according to the shrinking core model, with an activation energy of 41 kJ/mole.

Jan 1, 2003

By Marco Zurco, Claudia M. Mendez, Alicia E. Ares, Carlos E. Schvezov, Carlos M. Rodriguez

"Zinc-Tin alloys were solidified in horizontal form and the obtained results were analyzed. During solidification the distribution of temperatures were measured by using thermocouples located strategically along the length of the samples. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solids fronts. Comparing the structure of the samples and the values of these parameters it was found that the temperature gradient reaches minimum values of as low as - 0.6 °C/cm, and velocities of the fronts of around 0.1 cm/s. In addition, the grain size was measured along the samples. The results are presented and discussed in the frame of the results previously obtained for other alloys.IntroductionGenerally solidification leads to two types of grain morphologies: columnar and equiaxed. The origin of each one has been the subject of numerous theoretical and experimental researches in the field of metallurgy for many years [1-7]. The columnar-to-equiaxed transition, CET, is considered as an object of high technological relevance with respect to the directional solidification of metallic alloys. This structure transition may be sharp or gradual and it has been reported to be dependent on thermal conditions associated with the casting process, including melt convection, heat transfer coefficients at the metal-mold interface, growth rates, thermal gradients, cooling rates, transport of solute, alloy composition, melt superheat, mold temperature, mold design, casting size, casting geometry, and the concentration of nucleating particles. As a consequence, it is critical for industrial applications to understand the physical mechanisms which control this transition during solidification. Many studies highlight the importance of the relative growth of the equiaxed and columnar grains and develop expressions or numerical procedures to describe a criterion for the CET. A number of experimental investigations reported in the literature suggest that the CET occurs when GL in the melt reaches a minimum critical value [5-7]."

Jan 1, 2012

By Carlos Maurício Fontes Vieira, Sergio Neves Monteiro, Diogo Neves Henriques

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850 to 1100oC. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at temperatures above 1000 ° C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antônio de Pádua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antônio de Pádua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption and low mechanical strength [3,4]. To avoid these problems, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2008

By Guanghui Li, Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Xiaohui Fan, Zhiyuan Yu

With the increase of proportion of biochar(without modified) replacing coke breeze, the physical strength of sinter decreases due to the faster burning speed of biochar. An investigation upon passivating biochar with boric acid was then conducted to strengthen sintering in this paper. A layer of thin film of B2O3 distributed in the surface of biochar was observed, which could reduce the contact between reaction gas and biochar. So the burning speed of biochar was decreased properly after passivation, and the combustion efficiency increased due to the inhibition of carbon gasification. The comprehensive effects of above changes could increase the maximum temperature of sintering bed, which facilitated to the mineralization of sintering mixtures. Eventually sintering indices got reinforced. Thus the indices of sinter as applying 40% passivated biochar were comparable with that of 100% coke breeze.

Jan 1, 2015

By Ki Joo Sim, Sung Beom An, Joonho Lee, Minsoo Shin

Valorization of the electrical arc furnace oxidizing slag by coke was carried out by the reduction of iron oxide in the slag. Since the reduction of iron oxide by solid carbon is an endothermic reaction, supply of heat energy is required. In addition, slag has a low thermal conductivity; traditional fuel injection is not suitable for this reaction. Microwave can be used to supply heat energy to the system. Commercial oxidizing slag was reduced by coke under the microwave irradiation (1.7 kW, 2.45 GHz). The maximum recovery ratio of iron was 87%. In addition, slag composition modification was attempted to use the remaining slag for a mixture in cement clinker. Free-CaO in the slag was successfully suppressed, and the use of the remaining slag as a potential mixture was confirmed.

Jan 1, 2014

By Alex Luyima, Honglan Shi, Lifeng Zhang, Yongqing Jiang

"Leaching process has been suggested to recover most metals from waste PWBs. In this study, the leaching behavior of most metals present in waste PWBs is evaluated before and thermal treatment. Different leaching acids: hydrochloric acid (HCl), nitric acid (HNO3) and aqua regia are compared. The effects of acid concentration, particle size of sample, leaching time and temperature are examined. Results revealed that most metals are present in small particle size and sequential leaching of PWBs with a combination of HCl acid and aqua regia is capable of dissolving most of the metals content of PWBs. Leaching of thermally treated PWBs produced the highest leaching percentages for similar leaching conditions.IntroductionApproximately 20–50 million tonnes of electronic waste (e-waste) is produced globally per year. Waste Electrical and Electronic Equipment (WEEE) or E-waste is one of the fastest growing waste streams in the world. In developed countries, it equals 1% of total solid waste on an average [1]. The growing stockpile of used and obsolete consumer electronics has been called the “largest toxic waste problem of the 21st century [2]. Printed wiring boards (PWBs) is an essential part of almost all WEEE, and accounts approximately 3% of all WEEE by weight [3]. PWBs are a platform upon which microelectronic components are mounted. PWBs contain metals (~40 wt. %), ceramics (~30 wt. %) and plastics (~30 wt. %) [4]. The metallic part includes; Cu, Pb, Zn, Fe, Cd, Be, Cr, Au, Pt, Pd, Ag, etc. The plastic part of the PWBs is mostly epoxy resins. These plastic resins also contain very toxic halogenated flame retardants (HFRs) [5]."

Jan 1, 2012

By Yasuhiro Konishi, Norizoh Saitoh

"We have developed new recycling technologies, based upon an eco-friendly biotechnology, in order to extract precious and rare metals sourced from post-consumer products. Recently we have been focusing on the metal ion-reducing bacteria, Shewanella algae and Shewanella oneidensis, which are able to reduce and deposit the precious metal ions (gold (III), platinum (IV), palladium (II), and rhodium (Ill)) into metal nanoparticles at room temperature within 120 min. When targeting the leachates from printed circuit boards, the Shewanella bacteria were able to allow selective reduction and deposition of gold (III) ions under acidic conditions in the presence of heavy metal ions, proposing a new bio-recovery system for gold. We also found that the Shewanella bacteria can separate and concentrate soluble rare metal ions (dysprosium (III), indium (Ill), and gallium (Ill)) from dilute solutions. Using this biomass adsorbent, the effectiveness of system for the novel recovery of indium from the leachate of used LCD (liquid crystal display) panels has been demonstrated.IntroductionMany high-tech manufacturing industries are highly dependent upon the use of critical raw materials that are the rare metals (e.g. rare earth elements/indium) and precious metals (e.g. gold/platinum group metals). There are now serious global concerns over the short term and long term availability of critical raw materials for high-tech manufacturing. This highlights the paramount importance of sustainable component reuse and material recycling technologies for recovery of critical raw materials. We believe that the most important domestic source of precious metals is through more recycling, and this will require more research and further development for the recycling of precious and rare metals. In general, chemical/thermal recycling is deemed to be the most appropriate means to extract the precious and rare metals from postconsumer products. However, there are issues related to the heavy use of toxic and hazardous chemicals, and the release of toxic emissions.Biological recovery methods provide an attractive alternative strategy and use microorganisms to separate and concentrate soluble precious and rare metals from dilute solutions into microbial cells via biosorption [1-3] and biomineralization [ 4, 5]. Biological systems generally operate at ambient temperature and near-neutral pH. Consequently, microbial recovery of metals would be an environmentally friendly method for recycling precious and rare metals from end-of-use products."

Jan 1, 2014

By Corby G. Anderson

In nature, mercury is quite commonly found in association with antimony ores. This can be as a separate mineral such as cinnabar or in direct association with the antimony ore. The most common antimony-mercury mineral is livingstonite that occurs in places such as Algeria, Mexico, USSR and China. In the Roznava deposit in eastern Slovakia, tetrahedrite ore containing mercury ore has historically been processed pyrometallurgically for its silver and copper values. As well, in Tajikistan, major antimony deposits there contain significant mercury ore concentrations within the stibnite ore body. The mercury contained in these materials poses both a processing and environmental challenge. This paper will outline the processing of these types materials by industrial alkaline sulfide hydrometallurgical methods. The economics relevant to this potential application at Roznava in Slovakia will be outlined.

Jan 1, 2003

By N. Kanari

The thermal decomposition studies of two zinc basic carbonate samples were carried out up to 400 "C by thermogravimetric analysis, boat experiments and differential scanning calorimetry measurements 'DSC'. The initial samples and the solid decomposition products were analyzed by scanning electron microscopy, x-ray diffraction and laser particle size analyzer. The thermal decomposition of both samples started at about 150 "C and the rate of decomposition became significant at temperatures higher than 200 "C. The apparent activation energies 'Ea' in the temperature range 150-240 "C for sample decomposition were between 132 and 153 kJ1mole depending on the sample origin. The XRD analyses of the intermediately decomposed samples and the DSC results up to 400 "C suggest that the decomposition reaction probably occur in a single step.

Jan 1, 2002

By Vinod K. Sikka, René Cooper

"Cohoes, New York 12047 Intermetallics are an attractive class of advanced materials. The aluminide intermetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other intermetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (1) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intelmetallics into the forefront of research and their commercial applications. This paper has described a method for melting Ni3AI-based alloys that successfully utilize the exotherrn for the formation of NiAl from the elemental materials. The reaction-synthesis method has also been utilized for the production of NiAI and NiAI-based alloy powders from the elemental powders. The reaction-synthesized powders of NiAI and NiAI-based alloys were consolidated by hot extrusion and evaluated for tensile properties over a temperature range from room temperature to 1050ºC. The powder-processing conditions have been found to have more influence on the ductile-to-brittle transition temperature of NiAI than the powder-production method.IntroductionIntermetallics are an attractive class of advanced materials [1-11]. The alum in ide interrnetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other interrnetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (I) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intermetallics into the forefront of research and their commercial applications. The paper will briefly review the processing techniques being pursued for the commercial applications of Ni3Al-based intermetallics. The major emphasis of the paper will deal with synthesis of Ni3Al and NiAI intelmetallics."

Jan 1, 1994

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

By Raj P. Singh

Applications of cementation in the recovery of metal ions from process solutions have been known for a long time. Cementation reactions involve electrochemical precipitation of a noble metal from solutions of its salts on a more electropositive metal which, in tum, progressively dissolves. For example, addition of zinc metal powder in a solution containing zinc and cobalt ions would allow for the precipitation (separation) of cobalt according to the following chemical reaction. This paper pertains to the recovery of cobalt from cobalt process solutions via a cementation reaction on aluminum shavings (metal scraps from cans etc). Specifically, we report on the characterization of cobalt process solutions, a by-product obtained from cobalt chemicals, and the kinetics of cobalt, nickel and manganese cementation from process solutions on aluminum shavings.

Jan 1, 2000

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Army Research Laboratory (ARL) has an interest in the recovery and processing of rare earth elements. At Montana Tech, elevated temperature chlorination of rare earth oxides is presently being investigated as a potential methods leading to the selective separation and recovery of rare earth elements from mineral ores and concentrates. After preliminary evaluation, ytterbium oxide was selected as a representative surrogate material for more extensive chlorination studies. Methods used to determine the conversion and recovery include X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis. These data have been used to establish and confirm process conditions that consistently yield high conversion efficiencies. Based on the promising results, further experimentation is underway to ascertain the metallurgical response of other rare earth oxides and carbonates to the roasting process. The end goal is to create a robust process for industrial application that has greater efficiency and reduced costs as compared to current practice.

Jan 1, 2015