Search Documents

By T. Mutoh

Tellurium in raw slime has recently been recovered as copper telluride in Onahama Smelter & Refinery. The slime is decopperized with sulfuric acid solution in conventional leaching tanks. The pregnant leach solution containing 45 g/l of copper and 1 g/l of tellurium is introduced to a copper telluride recovering reactor. The tail solution from the reactor containing less than 20 mg/l of tellurium is recycled directly to circulation tanks of copper electrolysis. The impurities of the product copper telluride is kept below 1% without any purification.

Jan 1, 1990

By David Hughes

The paper covers the utilization of on-line analysis in process control of solvent extraction in nickel leach solvent extraction processes in Finland and Australia and in copper heap-leach and solvent extraction in Chile. The goals of and requirements for controlling the solvent extraction stages of the processes are reviewed. The applications at three plants are compared. The development of the technology used is reviewed and design considerations are discussed. Requirements for on-line control and analyzer performance are compared. A new generation of analyzers and its effect on the set-up process of a project is introduced.

Jan 1, 2003

By Wenjie Zhu

Chromite ore processing residue (COPR) is a hazardous waste containing high concentration of chromium. We describe here a pioneer trial of detoxification of COPR in column reactor with an indigenous chromate reducing bacterium Leucobacter sp. Ch1, which showed high chromate reducing ability at high pH. Under the optimum conditions, at 30°C and pH 10.0, pH of leachate decreased from 10.3 to 8.3, and Cr(VI) concentration in solution decreased to zero mg L-1, and 76.4% of Cr(VI) was removed from COPR samples. The leaching toxicity of detoxified residue was 1.1 mg L-1 that was lower than national standard of China.

Jan 1, 2008

By Hector Henao

To provide thermodynamic data for converting the nickel matte to liquid nickel, an experimental study was conducted in the phase equilibrium between the Ni-S alloy and the CaO-Al2O3 based slag melted in a MgO crucible at 1873 K under controlled Pso2 of 10.1 kPa and Po2 in a range between 2.5x 10-and 10.1 Pa by using CO-CO2-SO2 gas mixtures. The content of nickel in the slag at Po, of 10.1 Pa, above which solid NiO is expected to precipitate in the equilibrium state, was found to be 4, I mass% and the contents of sulfur and oxygen in the nickel melt were 0.4 and 02 mass%, respectively. ft was clarified that increase in the temperature reduces the solubility of nickel in the slag and the contents of sulfur and oxygen in the alloy, The distribution of minor elements such as gold, silver, copper, cobalt, iron, arsenic and antimony between the Ni-S alloy and the CaO-Al2O3 based slag was also studied. The distribution ratios of iron and cobalt, defined by (%X in slag)/[%X in alloy] where X is the minor element, are larger values than that of nickel, while those of copper, silver and antimony are similar to that of nickel. The distribution ratios of arsenic and gold are lower than that of nickel in the higher range of oxygen partial pressure.

Jan 1, 2003

By Jose Carlos D’Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano, Helio Marques Kohler

Nowadays the most important Direct Reduction - DR processes in shaft furnaces has to deal with carbon fines precipitation and DRI carburization issues. Based in a cooperative research program joining Catholic University (PUC-Rio) and SAMARCO Mining Co, a project dealing with pellets reduction and those two phenomena was established. This work analyzes kinetically the three reactions mentioned before, considering typical values for the operational variables temperature, flowrate, pressure and gas composition, parameters commonly used to control the DRI formation in the Reduction Zone - RZ of the shaft furnaces. From laboratories experimental results, the kinetic equations for those reactions were established and, using the superposition principle, generated a specific global kinetic model for the iron oxide reduction and the soot formation. Finally, using those experimental results and applying a planned statistical factorial analysis for the experiments, the numerical coefficients for each equation were calculated and the correlation factor determined for the proposed global kinetic equation.

Jan 1, 2015

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By Claudio Parra De Lazzari

The determination of the governing step of the deoxidation rate and the effects of the hydrogen content of the mixtures (C), the diameter of the delivery orifice (4) and the Reynolds number of the orifice (Re.) on the product Av kjg were investigated. A,, is the total surface area of the interface between the bubbles and the melt and kjg is the mass transfer coefficient in the gas phase. The design of the experiments was based on a two level statistically fractionated, factorial planning. Oxygen in the melt was measured as a function of time. It was found that the governing step of the deoxidation rate was the transport of hydrogen in the gaseous phase and that {Ay kjg} increases with C, {o} and Reo.

Jan 1, 1997

By W. Dresler

Design details of a 100 kVA DC electric-arc reduction furnace are described. The furnace is equipped with a 610 mm (24 inch) diameter graphite crucible hearth. A 76 mm (3 inch) diameter top graphite electrode is used as a cathode. The current passes through the bottom of the crucible and is carried to a bottom plate (the anode) by conductive magnesia carbon bricks. The furnace can be operated up to a maximum of 120 V, 1800 A, and presently 100 kW. The start-up operating experiences and metallurgical results of one reduction test with a Montana chromite containing 38% Cr2O3 are discussed.

Jan 1, 1994

By Hans Jürgen Maier, Gregory Gerstein, Florian Nürnberger

Microstructural analysis to support the development of material models provides valuable information to design complex forming operations. Damage models such as e.g. by Gurson consider spherical voids only. However, investigations of bcc steels by scanning electron microscopy reveal that voids exhibit an ellipsoidal shape with progressing deformation. The material’s weakening in the Gurson model is taken into account by the void volume fraction. Therefore, a three-dimensional characterization of the void shape offers important data for modelling. Thus, information on the anisotropy of the process of void evolution and accordingly, about the anisotropy of the deformation process is provided. Application of the information regarding the void shape anisotropy within the Gurson model is discussed.

Jan 1, 2016

By Xiaobing Yang, Abhishek Lahiri, Animesh Jha

"In the FFC-Cambridge process, the cathodic dissociation of oxide and CO/CO2 production on carbon anode is the basis for metal production in a CaCl2 bath. By using an inert intermetallic anode, the CO2 evolution can be eliminated altogether with acceleration in the electro-reduction kinetics. At present the process suffers from slow reduction kinetics of TiO2 to Ti metal, which can be enhanced significantly by the incorporation of alkali species in the TiO2 pellet at the cathode and in the CaCl2 bath in the presence of an intermetallic inert anode. Nearly full metallization with greater than 99% of Ti metal containing 1500 ppm of oxygen is possible to achieve in less than 16 hours of electro-reduction. Analyses of phase composition and the microstructures morphology in fully metallized pellets revealed the presence of localized solidified Ti layer, indicating that fast reduction process also involved formation of liquid phase as middle stage reaction. In addition, in situ creation of porosity and maintain higher current level during electrolysis process were two key factors to fully reduction of TiO2.IntroductionDuring cathodic dissociation of TiO2 in a CaCl2 bath and anodic evolution of CO2 on a carbon anode, which is the basis for the FFC Cambridge process [1], the rate of metallization slows down due to the formation of CaTiO3 at the reaction interface. Calcium and alkaline earth perovskites are known for their poor electrical conductivity which adversely affects the overall electro-reduction. One of the ways to increase the porosity is via the addition of polyethylene precursors in the pellet or by directly starting from perovskite [2, 3]. The experimental evidences shown in the literature confirm although the speed of reaction increases, but a complete or near complete metallization is not possible by enhancing the in-situ porosity alone, as the insulating perovskite is very slow to decompose under the equilibrium that prevails in the cell. Plethoric evidences on carbon anode show with the current decrease gradually, and finally stabilize at a very low value between 0.2 and 0.4 A, which is a testimony of the presence of perovskite insulating barrier in the current path. Our aim in this paper is to demonstrate the mechanism of enhanced electro-reduction when alkali ions are present in the oxide pellet at cathode and in the bath. We also show for the first time the use of an intermetallic anode for Ti-metal production using the FFC Cambridge process."

Jan 1, 2009

By Mingming Zhang

This paper describes the aluminum electrowinning in a batch recirculation cell system using 1-hexyl-3-methylimidazolium chloride and aluminum chloride (ionic liquids) as electrolyte at low temperatures. The technique proposed to deposit aluminum from ionic liquid electrolyte was a three-component electrolytic cell system. Ionic liquid electrolyte was circulated between electrolytic cell and electrolyte reservoir by ceramic piston pump. Two different anodes were used in the electrowinning and it was found the extruded carbon anode had better electrochemical stability and reusability. The cell performance variables studied were the current density and current efficiency as a function of aluminum ion concentration, electrolyte flow rate and applied cell voltage during batch recirculation operation. Results indicated that the current density was directly proportional to the applied cell voltage, initial electrolyte concentration and electrolyte flow rate. Under batch recirculation operation at applied voltage of 3.5 V and temperature of 80-90°C, 80-90% current efficiency of cathodic aluminum deposition can be achieved when flow rate is 20mL/min and initial concentration is 10 mol/L.

Jan 1, 2006

By Patricia Negrini Siqueira

Abstract. Polymers are susceptible to changes in their chemical structures that affect their mechanical properties under weather condition. Exposure of plastics to UV radiation causes a loss in their mechanical properties and/or change in appearance, including reduced ductility, color changes, yellowing and cracking. Today, there are several additive systems (light stabilizers) developed to work according to resin, final application, type of cultivation, and other characteristics. This study evaluates the different additive systems (Hindered Amine Light Stabilizer - HALS, nano calcium carbonate - NPCC, nZnO and nTiO2), applied 0.75% (in weight) in linear low density polyethylene (LLDPE). The samples were mixed by high rotation homogenizer and extrusion. Later, the samples were molded by injection and aged in QUV-B simulating 6 months of exposure to weather. Tests of FT-IR and tensile strength comparing to the non-aged samples were carried out in order to evaluate the performance of several additive systems.

Jan 1, 2015

By E. Salinas R.

This work is related with a whole characterization of cantera stone, to establish its characteristics that can give it an additional value for the reuse and reutilization of dust, slurries and small pieces of stone which can be treated as wastes. The obtained results reflects that the residues studied can be used as substitutes of feldspars in the production of pieces of ceramic, and also in the elaboration of paints for the same pieces according to the mixes that can be made with the variation of Na2O, CaO and K2O. According to the humidity proofs and specific gravity done, this material can be proposed as a soil improver into hydroponics systems, leading so an important alternative for food production in zones leaking of water. In the same way, it was found the possibility of use this material as a seal 3A in processes of asphalting of roads, highways and streets.

Jan 1, 2009

Four slag types covering the range of Fe-Ca-Si-O compositions and two iron blast furnace slags were melted at 1300 °C and doped with 1% of arsenic, antimony, cadmium, zinc and chromium. The melts were either slow cooled or quenched and the solidified slags were leached according to TCLP procedures. The morphology of the solidified slags was characterised using XRD, optical and electron microprobe techniques. Theoretical considerations showed that the capacity of the molten slag to hold the above toxic elements depended upon slag basicity and this was confirmed in practice. The experiments showed that the leaching of the toxic elements was a function of surface area and the phases present, both of which were affected by the mode of cooling. Iron silicate slags produced in nonferrous smelting operations and blast furnace slag from ferrous smelting operations both show promise of being suitable media for immobilising low levels of toxic elements and complying with current regulatory requirements.

Jan 1, 1994

By Luben Xie, Lin Hu, Qiang Wang, Min Gan, Tao Jiang, Wenqi Li, Yi Wang, Xiaohui Fan

"The mineralization behaviors of typical fluxes are studied by investigating the microstructures with optical microscope. The results show that the reactions begin with between iron ore and lime, limestone with small particle to form primary liquid. Then coarse limestone, dolomite and serpentine take part in reaction under the action of primary liquid. Limestone is the easiest to mineralization, next dolomite, and the last is serpentine. The higher basicity and smaller fluxes size favor the mineralization process of dolomite and serpentine.IntroductionThe purposes of adding fluxes into sintering are that:(1) to increase the basicity of sinter, so as to reduce even eliminate addition fluxes into BF(blast furnace) and decrease the coke ratio of BF[1,2]. (2) to decrease the melting point of sintering mixture to ensure sintering can be carried out at a lower temperature and reduce the energy consumption. (3) to improve the qualities of sinter by forming binding phase with iron ore fines [3].Flux is another significant component for sinter besides iron ore, especially for high basicity sinter[4]. The proportion of flux is usually higher than 10% in sinter mixture(excluding return mine).There were many reports about the influence of the flux types on sintering, such as limestone, dolomite, lime and so on[5-7]. It is very important to choose suitable fluxes for iron ore sintering. Although the effect of flux size on sintering also has been researched, the mineralization behaviors of the fluxes in the sintering process has not been illuminated. The paper will study the mineralization behavior of fluxes in sintering."

Jan 1, 2011

By Vojteh Leskov?ek

The tribological load is the load on forging tools resulting from the relative motions between the plastically deformed workpiece and the die. In comparison to many other forming processes hot die forging has an especially disadvantageous tribological system. The advantages of the application of hard coatings, which are well known for cutting tools, are to a much lesser extent explored for casting, extrusion, molding and forging tools. Increasing the lifetime of these tools is an important task in surface engineering because of the complex loading conditions and often complicated tool geometry. The plasma-assisted chemical-vapor-deposition (PACVD) technique is well suited to depositing hard coatings onto large dies and molds. The aim of this study is to present and discus results obtained on a duplex PACVD hard coating in an industrial application like the hot forging of automotive parts. A new generation of vacuum-melted and remelted (VMR) hot-work tool steels has been developed; these can reach a hardness of 58 HRc, and have a fracture toughness at this hardness equivalent to that of standard hot-work tool steels at 45 HRc. This offers one of two advantages: the steels can be used at the higher hardness to provide resistance to wear or deformation, or, when used at a hardness of 47?49 HRc for hot forging, to provide temper resistance, nitriding behavior and adhesive wear resistance. The results presented here are from a preliminary investigation. The experimental results indicate that the introduction of a proper duplex PACVD hard coating will lead to an improved wear resistance and a longer lifetime for the hot-forging dies. Furthermore, by using a hard, low-friction coating excellent anti-sticking properties can be obtained. At this stage of the investigation it is also necessary to carry out pilot trials to determine the wear resistance and the tool life in practice.

Jan 1, 2006

By Xuling Chen, Yi Wang, Xiaohui Fan

"The current control method of grate-kiln iron ore oxide pellet production is lack of accuracy and normalization due to the limited detection conditions. Therefore, mathematical models of grate-kiln temperature field are presented. With calculation of gas-particle heat transfer as well as enthalpy changes of moisture evaporation and magnetite oxidation, the thermal history of pellets throughout grate-kiln process can be acquired and used for production status estimation. Taking the calculated results as well as detected data in production as inputs, process parameters such as running speed, fan opening and coal injection rate as adjusting objects, expert system for grate-kiln pellet production is outlined. And the preheating section dominated control strategy is explained. Results of production application show that the stability rate of gas temperature in gas hood of preheating section is increased from 91.0% to 94.2%, compressive strength and first grade rate of pellet are increased by 3.62% and 2.36%, respectively, while FeO content is 18.18% lower. Control guidance of this expert system can solve production anomalies effectively, stabilize grate-kiln iron ore oxide pellet production and improve pellet quality.IntroductionSteel industry in China has developed rapidly in recent years. China’s crude steel production in 2010 is nearly 627 million, which is 44.2% of the world total production. Burden with higher quality is demanded by enlargement and modernization of blast furnaces. And oxide pellet production has become a growing concern. In 2010, the total production of pellet in China is 110 million, and about 60% is produced by grate-kiln process."

Jan 1, 2012

By Bo Jiang, Lianyun Liu, Hongmin Zhu, Kai Huang

"Watermelon peel is selected as a novel adsorbent to remove Pb(II) from aqueous solution. A simple saponification process is proposed to modify the peel and the adsorbent is characterized by SEM and FTIR. The effects of pH, contact time, initial concentration of Pb(ll), biosorbent dosage and temperature on adsorption of Pb(II) are investigated. Different models are used to fit experimental data. These models indicate that the adsorption process follows the Langmuir model and pseudo-second-order model. The maximum adsorption capacity obtained from Langmuir model is 1.05mol kg-1 for the prepared sorbent. Equilibrium time is attained in 5-10 min for the studied concentrations. The watermelon peel can be used as an effective and low-cost biosorbent for removal of Pb(ll) from aqueous solution.IntroductionRecently, removal of heavy metal ions from industrial effluents by biosorption has become a very attractive topic, since the more serious pollution issues caused by heavy metals emerge frequently, and more strict requirements for its control are called upon by society [1,2]. In this case, most conventional purification technologies are not suitable due to poor cost-effectiveness [3]. For example, chemical precipitation by alkaline reagents usually can not decrease the metal ion concentration below the permissive levels, and also it will produce a large amount of sludge containing toxic metals. Membrane separation techniques can realize deep purification of wastewater easily, although its operating cost is usually high. Thus, considering the high effectiveness, low cost and free-sludge operation, bisorption has become a promising technique in water treatment [4]. The most important thing for this technology is the synthesis of a suitable biosorbent, whose adsorption properties will determine the removal efficiency and economic cost for the whole process. Watermelon is one of the most popular fruits for mankind for its delicious flavor. Usually, the watermelon is consumed mainly for its edible pulp, and its peel is discarded or only used as feed for livestock. Considering the pectin contained in the watermelon peel, just like that in orange wastes in the reported literatures [3], the idea of using it as the raw material to prepare the biosorbents for heavy metal ions removal from the aqueous solution was evaluated in this study."

Jan 1, 2012

By K. Adham

For use in many existing and emerging applications, the purification of natural graphite is required to achieve +99.9% carbon content with minimum metallic impurities. Currently, the hydrofluoric acid process is used, which carries certain environmental and workplace health and safety impacts. While thermal purification of graphite at temperatures over 2500 °C is a known alternative, such high-temperature furnaces are expensive to build and operate. Using chlorine at lower temperatures to purify graphite is also known and patented, but is currently limited to treating solid synthetic graphite shapes in small-scale batch furnaces. Chlorine treatment of natural flake graphite resources can be used commercially, if certain drawbacks are addressed through process improvements that can be helped with the use of fluidized bed reactor technology.

By Zhen Zhang, Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie, Hong-Yi Li

Extracting vanadium from vanadium containing hot metal by LD process has been proven an effective solution for the utilization of vanadium-titanium magnetite ore, but the systematic analyses of vanadium extraction rate and mechanism by basic slag are seldom reported. In this study, mathematical model of vanadium transfer from metal to slag was formulated and the rates of vanadium extraction of hot metal with basic slag were investigated. The results indicated that the apparent vanadium extraction rate constant, kp, were in the range of 1.33~9.07×10-4g/(cm3·s). And the rate constant was increased with the increase of final slag basicity, reaction temperature and stirring gas flow. The apparent of mass transfer parameter decreases significantly from 0.13 cm3/ s to 0 cm3/ s in 20min, and the data changed as negative due to the decrease of slag oxidation and recovery of vanadium from slag to metal.

Jan 1, 2015