Search Documents

By Isıl Kerti, Sibel Daglılar, Sinem Yıldırım

In this study, effect of rolling and coiling temperature in thermo mechanical controlled process (TMCP), on the microstructure and mechanical properties of dual phase (DP) steel according to martensite volume fraction (MVF) rate was investigated. By using various finishing mill exit temperature and cooling conditions that is controlled laminar cooling system, the microstructural evolution of coil improves the mechanical properties with lower costs and higher productivities, in comparison to the heat treatment after rolling. The main part of the paper contains the result of tensile, yield and microstructure properties of DP600 steel produced on hot strip rolling plant and run- out table line. The results show that a higher MVF and an increasing cooling rate after the last deformation raised strength of the DP600 steel. The yield strength and ultimate tensile strength increase by decreasing coiling temperature.

Jan 1, 2015

By J. R. Wynnyckyj, R. Marr

Continuous measurement based on radiation pyrometry has often met with difficulties whose causes have been obscure. In this paper the experience gained with on-line pyrometry in utility and Kraft recovery boilers in the range 800-l400oC will be reported. It is shown that the inherent problems are best resolved by using a spectral pyrometer not sensitive to gas radiation. The radiation from the suspended particles thus provides the signal. It is further shown that the principle cause of difficulties is signal calibration drift caused by heat fluxes originating from surrounding surfaces and reflected by the particles to the pyrometer. Several examples are given how such problems may be resolved using process information and/or additional measurements, fed to and processed by and on-line microcomputer.

Jan 1, 1989

By J. D. Sloop

This paper discusses the current state of EAF dust recycling at AmeriSteel's Dust Processing Division in Jackson, Tennessee. Included are a brief history of the plant, a description of the facility, a description of the process, and operating data.

Jan 1, 2000

By Sergey Komarov, Manuela Diaz, Sano. Masamichi

"Mixing time, bubble behavior and absorption rate of gas injected into a liquid bath through rotary L-shaped lances have been studied by cold models with an effort to improve refining characteristics of metallurgical processes. Two kinds of the rotary lances were tested, namely the single-hole lance and the multi-hole lance. The effects of gas flow rate, bath depth and rotation speed were examined.It is found that when gas is injected through the rotary lances, the mixing intensity and the gas absorption rate are larger than that for the gas injection through stationary lances. The effect of rotation speed decreases as the bath depth and the gas flow rate increase.The multi-hole lance produces much smaller bubbles, which lead to an increase in the volumetric mass transfer coefficient by 3-4 times as compared with the single-hole lance. However, the effect of rotation speed is smaller for the multi-hole lance. The obtained results are explained in terms of the bubble coalescence and fragmentation, the rate of which depends on the departure bubble size and the power supplied to the liquid bath.IntroductionIn recent years, there has been a growing interest in the development of gas injector for metallurgical processes. The majority of the previous work was focused on modification to the injector design to improve mixing and to increase the of chemical reaction rate. These two goals can not be necessarily achieved by the same way. Bottom nozzles and stationary immersed top lances, which have been widely applied to steelmaking processes, are effective for the bath mixing, but have a limit to decrease in the bubble size. This results from a vigorous coalescence occurring between the bubbles when they rise in the molten bath as a bubble swarm.One of the ways to ensure the small bubble size and the effective bath stirring is the gas purging through rotary injectors. A number of studies have been undertaken to improve the refining characteristics by using rotary injectors. All of them are related to aluminum refining. The SNIF equipment (The Spinning Nozzle Inert Flotation) has significantly improved the quality of aluminum products at National Luxemburg Aluminum [1]. Rotary injectors made in the form of a disc have been applied to the Alcoa 622 [2] and the GBF processes [3]. A study of the gas injection by a rotary impeller has been carried out by C. Leroy and G. Pignacelt [4]. All researchers note the significant improvement in removal of sodium, calcium, hydrogen and non-metallic inclusion."

Jan 1, 1996

By John J. Mazza

Treatability studies were performed to determine the effectiveness of two commercially available treatment methods (solvent extraction and thermal desorption) for the removal of PCBs and PAHs from contaminated dredged riverbed sediments. The solvent extraction method evaluated was the B.E.S.T. process which extracts the contaminants with triethylamine. The thermal desorption method utilized was the ATP process which desorbs the contaminants at elevated temperature in an anaerobic atmosphere. A description of both methods and. an evaluation of the treatability study results is provided. Each treatment method was used to treat two separate samples (high and low concentration) from the site. Overall, both methods proved to be very effective with solvent extraction achieving 98% removal of both PCBs and PAHs and thermal desorption achieving better than 99% removal of both the PCBs and PAHs from the high concentration sample. Both solvent extraction and thermal desorption achieved greater than 99% removals of PCBs and PAHs from the low concentration sample. Vendor cost estimates for full scale treatment were roughly equivalent. The primary differences between the two methods lies in the realm of permitting, operational requirements, and emission concerns.

Jan 1, 1994

By Daniel C. McLean

Extraction data for Cu, Zn and Fe were obtained from 4.5" and 10" columns using massive sulfide ore and natural acid mine water. The purpose was to determine if recycling of solution through the column would produce leach liquors of 4 g/l Cu and Zn at extraction rates of 1 g/l per pass at typical flow rates of 0.002 to 0.006 gpm/sq.ft. Test results exceeded expectations. Cu and Zn concentrations of 4 g/l were obtrained within 4 to 6 cycles. Concentrations greater than 6 g/l Cu and 8 g/l Zn were reached within 10 cycles. Concentrations of greater than 40 g/l of Fe and free sulfuric acid were obtained with no decrease in biological activity being observed. No reagents were used.

Jan 1, 1995

By Ma Keyi, Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping

"The oxidation of the Multifunctional Electrodeposited RE-Ni-WP- SiC Composites at high temperature is investigated. The results show that during high temperature oxidation the relationship between the mass change of pure Ni , Ni-W-P, Ni-W-P-SiC or RE-Ni-W-P-SiC coating and the oxidation time follows a mixed curve, i.e. it is approximately a linear relationship when the oxidation time is less than 60 mins while it is a power function relationship when the oxidation time is over 60 mins. The order for the oxidation rate of the four coatings is Ni> Ni-W-P> Ni-WP- SiC>RE-Ni-W-P-SiC. The mass change of Ni-W-P, Ni-W-PSiC or RE-Ni-W-P-SiC coating increases exponentially with a rise of oxidation temperature. The high temperature-oxidation resistance of RE-Ni-W-P-SiC composite coating is 3-4 times that ofNi-W-P alloy coating. The cross section morphologies and Xray diffraction patterns indicate that the high temperature oxidation resistance of RE-Ni-W-P-SiC composite coating is better than any other coatings.1. IntroductionWith the rapid development of modem industries the products in engineering industry are continually challenged by the requirements of long-term and stable working at higher temperature, pressure, speed and under adverse conditions. Consequently, the surface properties of the products, such as the resistance to oxidation at high temperature, the resistance to wear and the resistance to corrosion, should be improved continually."

Jan 1, 2000

By Ann M. Hagni

Reflected Light Microscopy (RLM) And Scanning Electron Microscopic-Energy Dispersive Spectroscopic Analysis (SEM-EDS) Study Of Electric Arc Furnace (EAF) Dusts Have Shown That Their Mineralogy Is Complex And Varied. The Particles Are Largely Spherical, And Can Be Seen In RLM Sections To Be Composed Of Franklinite, And Zincite, But They Show Significant Solid Solution With Each Other And May Contain Small Amounts Of Chromium. These Crystalline Phases Occur As Crystals And Skeletal Growths Within Ca-Fe-Si Glass. Because Chlorine Is A Deleterious Constituent In Recovered Zinc Products From EAF Dusts, Special Attention Has Been Given To Chlorine-Bearing Phases, And They Include Hydrophylite (Cacl2), Lime (Cao), And Organic Phases. Pyrohydrolysis-Treated EAF Dusts With Silica (Si02), Tungstite (W03), Alumina (A1203), And Bunsenite (Nio) Additives Contain Franklinite, Scheelite (Cawo4), Willemite (Zn2SiO4), And Hematite (Fe2O3)

Jan 1, 1992

By Wantae Kim

In order to establish the optimized recovery process for heavy minerals from Korean beach sand, we investigated the several physical separation methods such as gravity and magnetic separation followed by mineralogical characterization. There was clear relationship between the particle size and heavy mineral content that heavy minerals were mostly concentrated in the particles below 100mesh. Gravity separation using the spiral and shaking table separators made it possible to concentrate heavy minerals by rejecting the light and coarse particles consist mainly of quartz and other non-valuable minerals. The high-intensity magnetic roll separator and subsequent induced magnetic separator were applied to fractionate magnetic particles according to their magnetic susceptibility. The content of TiO2 of high susceptible ilmenite-rich fraction was 43.98wt.% while those of ZrO2 of non-magnetic and magnetic residue were 6.78wt.% and 3.11wt.%, respectively.

Jan 1, 2006

By S. Rick Gilbert

In the course of producing a final metal product, smelters, refineries, and other metallurgical facilities produce wastes which often come under the ?scrutiny of Federal and state regulatory agencies. Many of these wastes contain combinations on zinc, copper, lead, cadmium, nickel or other metals. Frequently in the form of reverts, dusts, or sludges, these metal-containing wastes are often buried in a landfill or speculatively accumulated for future action. Environmental liability can be reduced in many cases by selecting,-a recycling facility which can re-process the waste for.' metal recovery. Encycle, at its hydrometallurgical facility Corpus Christi, has Successfully processed a variety of metallurgical by-products and wastes and returned those contained metals to commerce.

Jan 1, 1995

By Dong Liang, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"The formation, distribution and survival of pure Al nuclei under surface pulsed magneto oscillation (SPMO) treatment were investigated with thecombination of experiments and numerical simulation. The results indicated that the nuclei originated from the whole top surface of melt owing to the oscillation of top surface induced by SPMO. The temperature field significantly affected the survival of the nuclei The electromagnetic force and flow field of the melt with SPMO treatment were simulated by finite element software ANSYS. The electromagnetic force mainly distributed below the top surface near the mould wall. The electromagnetic farce not only made the melt oscillate but also increased the convection of meh below the top surface vigorously. The oscillation near the top surface of the melt promoted the nucleation largely, and the convection increased the uniform of the temperature distribution in the whole meh which favored the survival of nucleiIntroductionAs we all know, fine equiaxed grains are beneficial fur the improvement of the mechanical property, process ability and the uniformity of metallic materials [1-2]. With the researches of recent decades, people discovered that the electromagnetic field is an efficient method to refine the solidified structure of metals [3-7]. Pulsed magnetic field technology obtains more and more attentions in recent years due to its smaller power consumption, bigger instantaneous magnetic field intensity, non-contacting with the meh and simple convenient equipment manufacturing [8-9]. However, the melts would splash fiercely when pulsed magnetic field is applied with a slightly higher power. Thus, based on the understanding of the solidification refinement mechanism of electric current pulse (ECP) [10], Gong et al [11] developed a novel technology called pulse magneto-oscillation (PMO) to refine the solidification structure. The technology can be easily applied in the solidification structure refinement of continuous casting slab. But fur aluminum continuous casting, the sump is very shallow, which greatly limits the application of pulse magneto-oscillation technology."

Jan 1, 2014

By Murray Johnston

New measurements have been made on the equilibrium distribution of selenium and tellurium between molten slag and metal phases. Distribution coefficients of Se and Te between magnesia-saturated calcium ferrite slag and copper or silver alloys were measured over the temperature range 1473 and 1673 K under controlled oxygen patrial pressures of 10-11 to 10-0.68atm. The results demonstrate that the minor elements are present in the calcium ferrite slag as the selenide (Se2-) and telluride (Te2-) respectively, up to a PO2 of 10-6 atm. As conditions become more oxidising, Te undergoes a transition to the divalent oxide whereas Se does not. Increasing the temperature was found to enhance partitioning of the minor elements to the slag. In terms of activities, at 1573 K, Se showed strong negative deviation from the ideal behaviour in the slag, while Te showed only slight positive deviation.

Jan 1, 2006

By R. M. Cunningham

Asarco operates one of the largest individual copper electrolytic refineries in the world at Amarillo, Texas. The feed for this refinery is a mixture of anodes produced at Asarco smelters and copper purchased t?om a number of primary and secondary sources. The variation in feed makes it imperative that the refinery practices state-of-the-art quality control to minimize the effects'of unwanted impurities in the electrolytic refining process. In late 1993, a plant designed to sigru6cantly reduce the antimony and bismuth levels in the electrolyte was commissioned. The purification plant uses ion exchange technology in conjunction with a novel strippiing system developed by Zeneca Specialties (U.K.). The strippiing system permits the recycling of the eluant and thus avoids the extremely high costs of stripping with conventional reagents. In addition, the environmental impact of treating the eluant for recovery of antimony and bismuth is minimized. This paper outlines the development of the technology and, in particular, describes the operational practices and improvements at Amarillo since the commissioning of the plant.

Jan 1, 1997

By Taner Kavas

The refractory bricks of a rotary cement furnace containing of alumina and magnesium chromite were studied in order to determine whether they could be used in the concrete production as aggregates. Three mortars were prepared by mixing 1 part cement, 3 part aggregate materials, 0.5 part water by weight and mechanical, chemical, thermomechanical and microstructural characteristics were evaluated. The compressive and bending strength of samples were determined after 2 and 28 days curing. Resistance to chemicals were established by calculating the weight gain of mortars stored in 2 % HCl solution for 1 h and 24 h. Thermomechanical characteristics were determined by measuring the compressive strength of heat treated specimens at temperatures of 400 °C, 600 °C and 800 °C. Consequently, magnesium chromite containing waste brick aggregates have given the best results.

Jan 1, 2006

By Philip L. LeHoux

"Kennecott Barneys Canyon Mining Co. is a gold heap leaching facility that has been in operation since 1989. In 1994, a flotation plant was commissioned to remove sulphide minerals from refractory sulphide ore. Tailings from the plant are mixed with oxide heap leach material in order to produce a geotechnically stable agglomerate from which the gold is leached and recovered in a conventional heap leach cyanidation process. The experience to arrive at an effective blending methodology is discussed.IntroductionAgglomeration is the practice of binding fine particles to coarser rock or other fines in order to avoid the deleterious effects of mobilizing the fines during the course of heap leaching(l-Chamberlin). Agglomeration has been considered a key component of successful operation at many heap leach sites. If the ore is of sedimentary origin and crushed, there is a high likelihood that the resulting product will contain a significant quantity of fines and a skewed gradation, that i~, a disproportionate amount of coarse and fine particles, with few in the intermediate size range. The exact methodology for determining whether the practice of agglomeration will have to be integrated into the operating scheme has been well discussed. These conditions are primarily geotechnical and geochemical. This paper will deal with the specific experiences of Kennecott Barneys Canyon Mining Company in modifying the agglomeration practices to suit evolving operational requirements."

Jan 1, 1997

By Xingming Zhang, Huawei Zhang, Yanxiang Li

"A hybrid porous metal with nano-micro double scale pore size and regular-random bimodal porous structure has been fabricated by unidirectional solidification of a lotus-type alloy followed by dealloying treatment to the base alloy. The base alloy selected is a Cu-Mn binary alloy. The lotus-type porous Cu-Mn alloy with straight pores of several hundred micrometers in diameter was manufactured by unidirectional solidification with a mould casting process. Dealloying treatment was then done to the lotus-type porous structure of Cu-Mn alloy. The solid Cu-Mn alloy wall of the lotus-type porous structure was transformed to random porous structure of dozens to hundreds nanometers. The influence of corrosion parameters, such as the current and time in electrochemical corrosion, temperature and corrosion agent in chemical corrosion, on the nano-porous structure formed has been studied systematically.1. IntroductionA hybrid porous metal is a kind of cellular structure with different porous or cellular forms inside, which possesses special properties and can be applied in many fields as fuel cells, catalysis, sensors, etc. Several means have been developed to fabricate this kind of porous material [1-2]. In this paper, a novel process of Gasar plus dealloying is introduced to fabricate a new form of hybrid porous metal with nano-micro double size and regular-random bimodal structure.The Gasar process, also called the metal-gas eutectic directional solidification, that invented by Shapovalov [3] in Ukraine and now in USA some twenty years ago, is used to fabricate porous metals with regularly aligned pores basing on the solubility difference of a gaseous element in solid and liquid metal. Nakajima and his colleagues [4] in Japan studied this process further and called this kind of structure a lotus-type porous metal. They put more attention to various fabrication techniques and properties of lotus-type porous metals. Li heading a group [5-6] in P.R. China studied the mechanism of Gasar process and process controlling techniques. The Gasar pore structure and porosity can be controlled by processing parameters, and a regular Gasar structure with oriented pores distributing uniformly in the solid matrix can be obtained under optimized processing parameters."

Jan 1, 2014

By S. Yin, A. Bogno, H. Henein, P. Natzke

Impulse Atomization (IA) (a single fluid atomization technique) was used to rapidly solidify Al- 4.5wt%Cu and Al-4.5wt%Cu-0.4wt%Sc under argon atmosphere. In addition to the IA-generated droplets, the same technique was used to produce strips by Spray Deposition (SD) of the same alloys on a copper substrate with and without oil coating. The rapid solidification microstructures were analyzed using Scanning Electron Microscopy (SEM). From the SEM images, the amount of eutectic and the secondary dendrite arm spacing (SDAS) were measured. These SDAS results lead to the estimation of cooling rate. The eutectic fraction coupled with the metastable extension of the solidus and liquidus lines of Al-Cu (Sc) phase diagram lead to the estimation of primary and eutectic undercoolings. A comparison of the solidification path of the droplets and the strips was done as well as the analysis of the effects of scandium.

Jan 1, 2015

By Adam Powell, David Dussault

"Electric Field-Enhanced Smelting and Refining is a process for driving the reaction between carbon in hot metal and iron oxide in slag, for example, in a steelmaking reactor. This process involves inserting electrodes into the slag and metal phases, such that the overall reaction FeO + C -> Fe + CO is separated into two half-cell reactions: Fe2+ + 2e· -> Fe at the cathode in the slag, and C + O 2 • -> CO + 2e· at the anodic slag-metal interface. Without the electrodes, the reaction is very slow, but with electrodes, the additional surface area available to the ferrous ions for reduction accelerates the reaction even without any applied bias. When a bias is applied to the electrodes, the electric field across the slag further accelerates the overall reaction.With or without applied bias, the process is first-order in the ferrous ion concentration, and limited by ferrous ion transport to the cathode. To complicate matters, as the liquid iron is reduced at the cathode, the Mullins-Sekerka instability leads to formation of dendrite-like liquid iron fingers which grow into the slag. Because of this, the design of the cathode can have a significant effect on the overall process kinetics, and understanding of the dynamics of these fingers and of their effect on mass transfer is necessary for the intelligent design of the overall process and the cathode in particular.Toward this end, a detailed mesoscopic two-phase slag-metal model is presented here which describes multi component diffusion in the slag and fluid flow in both phases in the vicinity of the cathode. Diffusion in the slag is driven by chemical and electrical potentials. The phase boundary is modeled as a diffuse interface using a phase field approach. Because this electrochemical reaction occurs at high-temperature, the kinetics of charge transfer and adsorption through the double layer are fast relative to transport, permitting the use of simple linear reaction kinetics. This also eliminates the need to discretize the double layer, with the result that charge neutrality may be assumed everywhere in the domain. Introducing electric field dependence of the gradient potential and well height coefficients in the free energy function allows the model to capture electrocapillarity at the interface."

Jan 1, 2001

By Sharon K. Young

What might an ideal leach-to-cathode/product system look like in the next century? The paper looks at the synergies of the 60's and 70's that led to the highly effective copper leach SX-EW system of the 90's. Standing in the year 2020 focuses on what breakthrough technologies might make possible a next generation leach/extraction/metal recovery system. Many of the pieces of such a technology have been developed, even piloted: in situ leaching, enhanced bioleaching, heap leaching of fine particles, resin in pulp, ion exchange, alternate anode reaction electrowinning, novel anode coatings. With nearly non-existent research on the part of individual large companies, the greatest challenge may not be inventing the technologies but rather inventing an industry "will to create."

Jan 1, 1999

By W. B. Carter, A. T. Hunt, G. W. Book

"Combustion Chemical Vapor Deposition (CCVDSM ), an open air, flame assisted CVD process, is under development. The CCVD process produces non-line-of-sight, epitaxial deposition. Materials deposited include YBa2Cu3Ox' Y2BaCuOx, BaTiO3, Y2FesOI2, ZrO2, yttria stabilized ZrO2 (YSZ), partially (yttria) stabilized ZrO2 (PSZ), and amorphous silica. Two modifications of the CCVD process are being studied. Liquid fuel CCVD deposition, involves the combustion of an organic solvent that contains dissolved reagents carrying the desired coating cations. Gaseous fuel CCVD deposition uses a flammable gas as fuel. A non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol prior to its combustion. Substrates to be coated are held near the flames' ends.IntroductionThin films and coatings can be deposited using a wide variety of techniques including chemical vapor deposition (CVD). CVD is ""a materials synthesis process whereby constituents of the vapor phase react chemically near or on a substrate surface to form a solid product.""lIn conventional CVD processing, gases carrying coating constituents flow into a reaction vessel where deposition occurs onto a heated substrate. The deposition process is often conducted at reduced pressure. Both cold and hot wall reaction chambers are used. Heat can be provided by a resistance furnace, rf induction, or high-intensity radiation lamps. Plasma, microwave, photo, laser, RF, and electron-enhanced CVD processes have been developed. The necessity of using a reaction vessel limits the substrate size and affects coating economics. Although most CVD depositions are performed as batch processes, continuous deposition can be accomplished with the use of appropriate hardware.The chemical vapor deposition of thin, dense oxide films has been accomplished in the open atmosphere with a flame assisted process. The process is called combustion chemical vapor deposition (CCVDSM).2 Two modifications of the CCVD process have been developed. The liquid fuel CCVD process involves the combustion of an organic solvent in which reagents (containing the coating cations) are dissolved. The gaseous fuel CCVD process uses a flammable gas as fuel. In this modification, a non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol of small droplets prior to its combustion. Substrates to be coated are held near the flames' ends."

Jan 1, 1994