Search Documents

By Mario H. Castro-Cedeno

"A design for a handheld MEMS chemical detector is proposed. The detector will be used to detect trace amounts of chemicals in air. It can detect drugs, toxic chemicals and/or explosives. The proposed detector will use ion mobility spectrometry (IMS), a technique that is well known for accuracy and has been used in the past in suitcase sized chemical detectors. The separation and detection of the chemicals occurs in the drift channel and the process was modeled using the finite element method and CoventorWare modeling software. A manufacturing process sequence for the drift channel is proposed and was demonstrated.IntroductionThe goal of this effort is to design, mode~ and prototype a MEMS chip that will be the key component in an ion mobility spectrometer (IMS). This technique uses and asymmetric potential to separate the various ion species in a stream of incoming air [1-4]. One advantage of IMS is its ability to separate chemical species from air at atmospheric pressure and temperature. This is a requirement for a simple to use handheld drug or chemical detector. IMS can be used to detect drugs, toxic chemicals and explosives and it is well known for accuracy in detecting very small amounts of chemicals. This chemical detection technique has been used in the past, but not in handheld detectors.One variant of IMS is the high-field asymmetric waveform ion mobility spectrometry or FAIMS [3]. The FAIMS process, shown in Figure l, works as follows: a gas sample is admitted into the instrument where gas molecules are ionized, typically by a weak radioactive isotope source, ultraviolet light source; and more recently through field emission. The ions move along the length of a channel while they are separated in the transverse direction by an asymmetric electrical potential. The potential, in the form of an asymmetric waveform, causes relative motion between the various chemical species. The species that hit the charged top and bottom plates are neutralized and only those ions that move along the center are detectable as charged chemical ions at the end of the channel."

Jan 1, 2004

By D. M. Hausen

A refractory siliceous low-grade silver ore (265 g/t Ag) from a prospect in Sonora, Mexico was investigated mineralogically and metallurgically to evaluate extraction of the silver by conventional methods. Approximately half of the silver was recoverable, occurring as coarsely crystalline acanthite (70-300 Am) that was liberated in material crushed to minus 10 mesh. The remaining silver is refractory and occurs mostly as finely locked (-2 to 0.2 Am) acanthite in cherty quartz, and as minor amounts of finely disseminated stylotypite or freibergite in fluorite. The mineralogic data have thus served to explain the 50-60% recovery of silver by flotation and cyanidation.

Jan 1, 1991

By Ryosuke Matsuoka

Keywords: Tantalum capacitor, Scrap, Recovery, Titanium, Chlorination A recycling process for tantalum from capacitor scraps using an oxidation process followed by mechanical separation and chemical treatment was investigated. This study demonstrates that sintered tantalum electrodes inside the capacitor scraps can be mechanically collected after the oxidation of the scraps in air, and high-purity tantalum oxide powder (Ta2O5) was efficiently recovered after chemical treatment. By reducing the Ta2O5 obtained through magnesiothermic reduction, tantalum powder with 99 mass-% purity was obtained. Using the chlorination for tantalum recovery was also investigated, and the tantalum or tantalum compounds were reacted with chloride wastes such as FeClx. It was found that tantalum was effectively separated and purified when tantalum powder is reacted with FeClx at 1100 K under an argon atmosphere. This recycling process utilizing chloride scrap has now been extended to other reactive metals such as titanium.

Jan 1, 2004

By Ahmad Umar

A variety of ZnO nanostructures such as sea-urchin-like structures composed of nanowires and nanorods, nanocombs, nano/micro spheres and cages, star-shaped ZnO nanostructures, flower-shaped nanostructures, needle-like nanostructures etc. have been synthesized applying two different fabrication techniques i.e. thermal evaporation and cyclic feeding chemical vapor deposition techniques at different reaction parameters such as reaction temperature, growth period, reactant concentrations, types of source material and substrates etc. It was observed from the experiments that the morphologies of the grown structures were highly influenced by the reaction parameters and fabrication techniques and specific morphology can be obtained at particular reaction parameters in a specific synthetic procedure. Extensive morphological investigations of the obtained products demonstrate that the grown structures are single crystalline and having a wurtzite hexagonal phase. Room-temperature photoluminescence spectra of all the deposited products exhibited good optical properties. Finally, the growth process of the fabricated structures were proposed and discussed in detail.

Jan 1, 2006

By Andreas Dietrich

Laser off-gas measurement of CO, O2 and temperature has been carried online in EAFs. A visualization screen shows the values of CO and Oxygen and temperature for the entire heat, and includes the status of furnace equipment. The historical data of the heats are stored such that the furnace performance can be evaluated and optimized. A short comparison between laser based and conventional systems has been carried out related to speed, influence of dust, water, pressure, protection for bag house explosions. A high water and/or dust content in the sample does not represent a problem for this type of system. The measurement method works without interruption even under worst conditions such as dirty scrap, carbon injection etc. The installation was developed in conjunction with Marienhuette, Graz. They are 100% scrap based with a tap to tap time of ca. 46 min. Keywords: Laser Measurement, Off Gas, CO, O2, Temperature

Jan 1, 2003

By Hiroyuki Matsuura, Fumitaka Tsukihashi

"Emission of CO2 gas from steelmaking industry covers more than 12 % of total CO2 emission in Japan. Though many efforts have been made to curtail energy consumption and high energy efficiency of Japanese steel production process has been achieved so far, further reduction of CO2 emission is strongly requested to develop sustainable steel production process and produce “green material”. Recently, authors have proposed the innovative hydrogen production process, in which water vapor is reacted with discharged steelmaking slag to produce hydrogen gas. This reaction can be achieved without any external energy source and operated by huge thermal energy associated with steelmaking slag and FeO or unrecovered Fe droplets that are relatively rich in the slag. In this paper, thermodynamic calculation results with various initial conditions in terms of hydrogen productivity were presented. Laboratory-scale experiments were also conducted to clarify the validity of thermodynamic calculation and the reaction rate in realistic conditions.IntroductionIronmaking and steelmaking process from iron ore through blast furnace and BOF is an essential steel production route for Japanese steel industries to supply high quality steel products in large quantity to society stably. Blast furnace – BOF process requires huge amount of fossil fuels such as mainly coal, resulting the emission of considerable amount of CO2 gas. Since the emission of CO2 gas from steel industries, about 147 Mt (FY2011), accounts for approximately 12 % of domestic CO2 gas emission in Japan (FY2011),[1] it is an urgent issue for steel industries to develop environmental-friendly ironmaking and steelmaking process and reduce CO2 emission. Various kinds of gases and by-products generated from ironmaking and steelmaking processes have been recycled as much as possible at present. Enormous thermal energy is also generated from processes and released to surrounding atmosphere as various forms such as sensible heats of gases, molten steels or by-products, and as heat losses. However, these energies are not utilized before final dissipation to atmosphere. Although various technologies to utilize thermal energy from ironmaking and steelmaking processes have been attempted to develop, practical application of these technologies has not been achieved because the thermal energy is not always useful as an energy source. In steelmaking process by BOF, fluxing agent such as CaO is added during reefing and thus about 100 kg/t-steel of steelmaking slag are generated. Since the steelmaking slag is discharged at temperature range between 1873 and 1923 K after discharge of refined molten steel, it also has large thermal energy. Amount of generated BOF slag is 11.0 Mt/y (FY2012) in Japan.[2] Assuming the amount of steelmaking slag is 10 Mt/y and its average heat capacity from room temperature to 1923 K is 1 kJ/kg·K,[3] unutilized heat is estimated to be 16 PJ/y, which is equal to annual energy consumption of 420 thousand families in Japan.[4]"

Jan 1, 2014

By Zongliang Zhang

Electrowinning is a significant step in metal extraction processes. Because the nature of electrowinning is to reduce metal from its oxidized state, substantial energy consumption accompanies it. Electrowinning processes of different metals have much in common—the deposition of the metal on the cathode and the counter-reaction on the anode. An advanced model was developed that can be applied to a variety of metal electrowinning processes. A model for specific metals can be readily obtained by modifying parameters such as potential, kinetics, and side reactions in the model. The model incorporates mass transfer, gas-liquid flow, electrochemistry, and deposition, making it a comprehensive electrowinning model. The model is applied to copper, nickel, and zinc and verified with the experimental results. In addition, the parameter settings and results of different metals were compared, showing that this model has great versatility and accuracy, thereby making it an efficient and effective research tool.

By W. K. Rankin

Achieving continued economic growth with social equity within the natural limits of the Earth's eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

By Jean-Louis Dirion, Guy Depelsenaire, Patrick Sharrock, Souhila Kribi, Ange Nzihou, Jocelyn Ramaroson

"This study assesses the Novosol® process, an emerging technology developed by Solvay to treat heavy metals from dredged sediments using phosphoric acid. The main goal is to convert toxic metal ions, such as Pb2+, Cd2+, Zn2+ and Cu2+ to insoluble metallic phosphates. The effectiveness of the treatment was evaluated by performing the chemical reaction in a tubular reactor, followed by convective drying and maturation of the treated sediment at ambient temperature and finally thermal destruction of the organic matter by calcinations (500°C-700°C). Selected variables (acid concentration, volume fraction of solids, flow rate, drying and calcination temperature and time) were investigated. Laboratory scale experiments were carried out with various combinations of these parameters. The influence of the quantity of acid and the temperature of calcinations on physical properties of the sediment and stabilization of the heavy metals are discussed. Introduction The French territory counts 525 000 km of rivers which transport each year on average 6 million m3 of sediments. Their deposit causes the silting of channels, rivers and lakes. This completely natural phenomenon is exacerbated by the introduction of industrial and urban wastes into the erosion and sedimentation process. This silting leads to clogging of rivers, with a reduction in their flow rates. Consecutively, other problems appear, such as flooding risks, decrease of biological purification capacity and associated loss of the biodiversity. The presence of toxic compounds (from industrial, household or agricultural origins) in the sediments worsens the situation, and requires curing to restore the natural environment and its function. The dredged sediments are either spread on agricultural land, land tipped, confined or sent for chemical or physical treatment [12]. The first research programmes on toxic sediments appeared at the end of the Eighties in the United States, in Canada, in the Netherlands and in Germany. Several techniques of treatment were developed for the sediments; these techniques can be used alone or in combination. These techniques include extraction and concentration of the pollutants: the pollutants are isolated from the sedimentary matrix and the sediment is decontaminated. In some cases of organic contaminations, the pollutants are destroyed by chemical oxidation or biodegradation and in other cases, the contaminated material is either stabilized (mixed with hydraulic binders), or destroyed (incineration) [14,15]. Phytoremediation by afforestation has also been reported [19]."

Jan 1, 2008

Roasting treatments were investigated to remove arsenic from a nickel concentrate. The main arsenic minerals and their proportions in the concentrate were niccolite (NiAs)-50%, gersdorffite (NiAsS)-40% and arsenopyrite (FeAsS)-10%. Thermal analysis showed that gersdorffite and niccolite began decomposing when heated above 640 and 830°C respectively. The maximum roasting temperature was limited by agglomeration of the concentrate above 900°C. A small vibrated bed reactor was used to investigate the effects of temperature and gas flowrate, the latter to sweep away evolved arsenic. At 900°C, 24% of the original arsenic remained in the concentrate. SEM examination of the calcine showed that the residual arsenic was associated with the calcium in the gangue minerals. Additions of sulphur (either as elemental sulphur or from pyrite) facilitated the decomposition of the arsenic-containing minerals, decreased reaction with calcium in the gangue and produced calcine containing 4-6% of the original arsenic. Treatment with chlorine during roasting was effective in reducing the arsenic content to similar levels. Generation of chlorine in the bed by sulphation of CaC12 also produced encouraging results. Arsenic, Nickel Concentrate, Roasting, Chlorine, Sulphur, Gersdorffite, Niccolite

Jan 1, 2005

By Rafael Colás

Computer visualization can be employed in industry as an aid to the understanding of the complex interactions between variables encountered in production. The examples of ingot casting of rimming steel and that of hot rolling of low carbon steel strip are presented. Both processes are mathematically modeled, and their results are presented in a graphical way. Such models have been proven to be an asset in quality improvements and increase of productivity as the personnel involved get a better understanding of their job.

Jan 1, 1993

By B. M. Satish

The aim of the present work is to study the effect of annealing on the vibration damping capacity of high-chromium (16%) ferromagnetic steel. The alloys were prepared from raw materials of 99.9% purity melted in a high frequency induction furnace under high vacuum. The samples were heat-treated in vacuum at various temperatures (800 to 1200°C) for 1 hour followed by slow cooling (120°C/h). The inverted torsional pendulum method was used to evaluate the vibration damping capacity. The results indicated that the vibration damping capacity of the alloys is influenced by annealing and there exists a critical annealing temperature after 1000°C. The damping capacity increases quickly below the critical temperature since the magnetic domains move more easily.

Jan 1, 2009

By A. J. Maselli, E. C. Cemak

Hartford Steel Technologies (HST) has a pyrometallurgical and hydrometaliurgical process capable of reclaiming valuable metals from a hazardous waste· stream such as EAF Dust. The HST Process effectively addresses the growing environmental concerns surrounding the increasing production of EAF Dust without producing any hazardous waste material as byproducts. Currently EAF Dust production levels are exceeding the 1,000,000 metric tons per year mark. The HST Process is designed to separate iron, zinc, lead, cadmium, copper, and silver metals using a two-phased process. The Pyrometallurgical side of the Process utilizes a Rotary Hearth Furnace to separate the iron metal from the remaining metals. These remaining metals are further separated, using a Hydrometallurgical Process, in a series of digestion tanks. The individual metals are then collected in saleable form.

Jan 1, 2000

By D. A. Milligan

Ammonia leaching of copper sulfide concentrates, matte, scrap or other sources of copper yields copper amnine sulfate solutions which are converted to metal in a two-stage process involving precipitation of inter- mediate sulfites and their thermal decomposition to copper powder of high purity. Processing details and results are given. Considerable simplification in circuitry and cost savings are indicated. Energy requirements are reduced by substitution of copper powder precipitation and ammonium sulfate crystallization for solvent extraction, electrowinning and lime boil.

Jan 1, 1976

By A. Kiziltas, D. J. Gardner, C. W. Mcllwraith, J. W. Bridge, M. L. Peterson

"Dynamic mechanical thermal analysis (DMTA) tests were conducted on high-oil content, paraffin-based wax used in wax-coated granular composites. These composites make up the surface of synthetic Thoroughbred horse racetracks used in North America. The modulus and damping response from the DMTA tests were correlated with the dynamic triaxial shear strength response of the bulk track material taken at two different operational temperatures and at four strain rates. The purpose of these tests is to understand the mechanisms of shear strengthening of the bulk track material as the wax is heated through the first crystalline solid to liquid nominal transition temperature. Previous work using differential scanning calorimetry confirmed that under common operational surface temperatures, the wax coatings undergo distinct thermal transitions. The resulting increase in triaxial shear strength values affects the consistency of the racetrack which, in turn, can potentially affect Thoroughbred racing performance and safety of the track surface.IntroductionSynthetic granular composite materials are being used in nine Thoroughbred horse racetracks in the United States as well as in other tracks around the world. In one case, their use was mandated by the state of California in 2007 due to testimony that these tracks were significantly safer than traditional dirt tracks [1]. Several synthetic tracks have shown substantial reductions in injuries since switching to synthetics; one California track showed a 75% reduction in catastrophic horse injuries during the first year as compared to the previous year racing on a dirt track [2]. The composition of the tracks in the U.S. generally consist of silica sand (>70%), polymer fibers (<5%), and rubber particles (0-15%) all coated with a paraffin-based, high oil content wax [3, 4]. In a recent study of several synthetic racetracks, to include the track location in this study, the oil content ranged from 34 to over 44% by mass [5]."

Jan 1, 2011

By Mark Cross, Andrew P. Campbell, Koulis A. Pericleous

"Computational Fluid Dynamics (CFD) modelling is being used to simulate the freeze layers formed within direct smelting processes. There has been some concern whether water-cooled elements can withstand the p~ocess conditions and in particular abnormal cases where they may be splashed in molten metal.To validate the models being developed, two cases from literature have been modelled for solidification and stress analysis. The solidification case is presented in detail and is for hot molten metal flowing through a cylindrical pipe. The walls are at a temperature below the melting point for the metal. The resulting solid (or freeze) layer is within 3% of the value calculated by Sampson & Gibson9 •Preliminary modelling of the refractory-slag interactions is presented. Although three basic mechanisms: Penetration; Corrosion; and Erosion will eventually be modelled, only the penetration is considered here. The corrosion mechanism is to be modelled by tracking the time that the penetrated refractory is at the required temperature.Future work, after adding all the required physics, will focus on the modelling of a water-cooled element placed lower in the smelter. Process perturbations will be simulated to examine what these elements will withstand."

Jan 1, 2001

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"In this study we attempted to model a response surface for the apparent dry density of ternary blends of calcitic marble particles. The crushed marble was divided into three granulometric ranges. Simplex network methodology was used to determine the mathematical relation between granulometric ranges and apparent dry density (ADD) of particle mixtures. A highly significant regression was obtained and the simplex network methodology proved to be able to predict high packing particle compositions.IntroductionProblems with packing and expected porosity of particles are common and widely recognized to be important in terms of both fundamental physics and engineering applications. For example, densification of a powder mass is important in the shaping of solids in ceramics, powder metallurgy or composite synthesis; chemical processes such as solid-liquid separation (sedimentation, thickening and filtration), raw material handling (stockpiling, blending, drying, storage and transportation) and pyrometallurgical processes (agglomeration, coke making, ore sintering, blast furnace iron making and new iron making processes) [1,2].Many factors can affect particle packing, but in practice, there are three main factors: (dimensionless) particle size distribution, particle shape and absolute particle size [2].Geometrical and practical methods were developed to predict properties in mixtures. Zou, Gan and Yu [2] present a paper treating a prediction of the porosity of multi-component mixtures of cohesive (fine) and non-cohesive (coarse) particles. Bahiense et al. [3,4] used a simplex network to determine a mathematical model for obtain the optimal compositions between aggregates to a greater packing of a ternary particles mixture. Despite these techniques for predicting particle packing, some studies in particulate composites production don't present clear criteria for choice of particle distribution [5,6]. As the best particle packaging depends on the size, distribution and shape of these particles, individual models can be constructed for specific combinations of these factors."

Jan 1, 2014

By Sanaz Mosadeghsedghi

The feasibility of the application of electrodialysis in separation of light and heavy rare earth elements (REE) in synthetic solutions was investigated. The experiments were carried out using single and binary solutions of a light (cerium) and heavy (ytterbium) REE. The effects of electrical voltage, electrical current, and the addition of complexing agent (EDTA) to increase the separation selectivity were investigated. Separation of Ce and Yb was achieved in binary solutions with and without the addition of EDTA. Higher degrees of separation were seen at higher voltages. Ce–Yb separation was more significant in the presence of EDTA. The separation factor of Ce–Yb and Ce–Yb-EDTA were 1.44 and 2.60, respectively.

By W. G. Davenport

Chapters 7,8and 9 calculated three combinations of: blast composition (mass% O2, mass% N2) oil quantity per tonne of concentrate blast temperature that will steadily produce molten 65% Cu matte from pure chalcopyrite-concentrate. The combinations are:

Jan 1, 2001

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016