Search Documents

By A. V. Tarasov

One or more of the main alloying metals, i.e. copper, silicon, nickel, magnesium, zinc and other metals can form a composition with aluminum, by dissolving in the latter. The thermodynamic computations have indicated that within a range of temperatures from 700°C to 1300°C the reactions of molten aluminum with zinc and nickel oxides are shifted toward formation of free metals because it is possible to use the main alloying metals, i.e. zinc and nickel, in the form of inexpensive intermediate products and waste. The laboratory studies conducted have confirmed a possibility for production of aluminum alloys using intermediate products in the form of oxides of alloying metals.

Jan 1, 2006

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The basics of microwave drying process of CuCl residue were studied by comparing the dielectric property of the residue with different moisture contents. The dielectric properties were measured by microwave cavity perturbation method. The dielectric constant and dielectric loss factor of the CuCl residue have a linear correlation with the moisture content. With this relationship, we can realize on-line measurement of moisture content of the CuCl residue by dielectric properties. The microwave drying experiments with different thicknesses (1-5cm) of CuCl residue were carried out, and the heating curve of the materials under different microwave powers (250-450W) was made. From these parameters, an optimized operation parameter of microwave roasting technology, the thickness of CuCl residue filter cake to be microwave roasted should be 2cm , was deduced.

Jan 1, 2015

By J. R. Hartin

Traditionally, many of the advances in casting technology have been made by expensive and time consuming trial-and-error methodology. Modeling of the complex solidification process promises production of castings which are made "right the first time." Even though several models are available for simulation of conventional casting processes, none of them address this relatively new technology of investment cast titanium aluminides. In this paper, modification and application of a transient, three-dimensional, fully coupled fluid flow and heat transfer solidification modeling computer program to the analysis of centrifugally cast titanium aluminides is discussed. The predictive results of the program are compared to qualities of actual cast parts for validation.

Jan 1, 1992

By J. -P. Nepper

It has been possible to largely contain converter aisle emissions of SO2 and fumes in the case of batch-wise operated Peirce Smith converters during normal blowing periods with the help of suitably designed primary hoods. Controlling the escape of off-gas during the periods of turning the converter in or out of the stack has been problematic in the past. Effective automated contro1 systems have been deve1oped for the purpose and successfully applied in smelter operations in Spain, Taiwan and Germany. This has led not only to an effective reduction of emissions in the converter environment but also to an improvement in the converter operation.

Jan 1, 1992

By Xuemei Zheng, Aiyuan Ma, Yonggang Zuo, Jinhui Peng, Shiwei Li, Libo Zhang

The effect of moisture content on the dielectric properties and microwave drying behavior of zirconium hydroxide was studied by using an open-ended sensor dielectric measurement system at the frequency of 2.45 GHz. The experimental results showed that moisture content can significantly influence the variation of dielectric properties. Dielectric constant, loss factor and loss tangent all increase with the increasing moisture content. Compared with the conventional drying method, the microwave-assisted drying method resulted in a substantial decrease (81.8%) in the drying time, and the drying effect was better at the lower power level of 600 W. This study offers the useful information on dielectric properties of zirconium hydroxide, which can be used for developing microwave drying applications in mineral processing and designing better microwave sensors for measuring zirconium hydroxide moisture content.

Jan 1, 2015

By Yang Guangqing, Shao Jiugang, Zhang Jianliang, Wan Dan, Fu Yuandi, Guo Hongwei

"Resource of metallurgical coke is becoming scarce, and although coke can be partially replaced by pulverized coal injection, there are many restrictions for further increase in coal ratio. Mixed charge of ore and lump coal from top to replace more coke was studied in this paper. Softening-melting property of the burden was affected by charge of lump coal. Softening-melting properties of mixed charge of ore and coke, mixed charge of ore and lump coal were tested respectively. Results show: the property of the burden mixed with coke is superior to the burden mixed with lump coal; lump coal would not deteriorate softening-melting property of the burden and some of them can even improve softening-melting property of the burden. Top charge of lump coal would not deteriorate softening-melting process, and this should be a new way to increase coal consumption to decrease coke rate.IntroductionThe blast furnace is still the predominant process for the reduction of iron ore and will probably remain so for the next decades. Metallurgical coke is becoming scarce and expensive, so the cost of hot metal can be decreased by reducing the consumption of metallurgical coke[l]. Coke can be partially replaced by pulverized coal injection, currently the highest rate of pulverized coal reached 266kg/tHM, most of blast furnace PCR is about 150kg/tHM, and it is very difficult to further increase of PCR. Nut coke is charged into blast furnace mixed with iron ore, not only for improving utilization of metallurgical coke, but also for lowering the coke rate. Presently the majority of blast furnaces in the world use nut coke although its amount is very different: from 10-20 to 70--100 kg/tHM and more[2-4].The effect ofnut coke in blast furnace is extensively researched, and the main conclusions recommend: to improve gas permeability of cohesive layer in blast furnace, to promote reduction of iron burden, protect metallurgical coke from the solution in the shaft due to higher reactivity of nut coke. There is no special requirement for the strength of nut coke[5-8]. Nut coke is also used for sintering fuel, which may lead to the shortage of the nut coke charging into blast furnace. So lump coal mixed with iron ore is considered to be charged into the blast furnace, not only to reduce the cost of grinding coal, but also to increase the use amount of coal."

Jan 1, 2013

By John J. Mortvedt

Application of some by-products of the metals industry which contain plant nutrients to agricultural lands could constitute resource recovery instead of costly disposal. Some industrial by-products contain appreciable concentrations of heavy metal contaminants, such as Cd, Cr, Ni, and Pb. After land application, these metals may be absorbed by plants and enter the human food chain or be leached to groundwaters. Plant uptake of these heavy metals varies with plant species:, soil pH, soil texture, and the particular metal. Certain leafy vegetables can absorb significant amounts of heavy metals, while absorbed metals are usually poorly translocated to cereal grains. Allowable heavy metal concentrations in fertilizers now are not regulated, but EPA is considering such regulations. Heavy metal impurities in animal feed supplements are regulated by the states; so some by-products may not be permitted for this use.

Jan 1, 1992

By Jim Sarvinis, Rory Hynes, Elizabet Cruz, Kerry McKenna, Maytinee Vatanakul

"Energy efficiency improvements achieved using heat recovery processes offer benefits to both the business case and environmental impact of metallurgical facilities. Global demand drives the development of lower and lower grade ore bodies. This trend results in higher energy intensity and consequently increased waste heat. Waste heat boilers and Organic Rankine Cycle (ORC) processes are becoming cost competitive methods of utilizing this waste heat.This study analyzes heat recovery from available sources to produce power using, • High grade: waste heat boiler and steam turbine generator. This system will produce electricity, and/or process steam.• Low grade: ORC to produce electricity. The cycle is well adapted to low- moderate temperature heat sources.Processes used in metallurgical plants, such as hot exhaust streams, cooling and condensers could benefit from application of these systems.The study demonstrates:• The energy and cost saving potential of waste heat recovery technologies,• The environmental benefit.IntroductionIn recent decades, process intensification has resulted in increased productivity from unit operations such as kilns, fluidized bed reactors and smelting furnaces and decreased unit operating costs. In the coming decades, the industry’s challenge will be to continue this trend while at the same time decreasing the consumption of fossil fuels and further reducing the environmental impact of its processes.The U.S. Department of Energy reports that available waste heat sources in industry, which is approximately seven quadrillion BTU (~7,400 PJ/y), exceeds the current production of all renewable power sources combined. In Canada there are about 2,300 PJ/y of available waste heat, with the pulp and paper, metallurgy, chemical/petrochemical and oil refining industries the main players. Natural Resources Canada (NRCan)9 has estimated that about 25% of that heat could be recoverable using existing technologies, which in turn, represents a reduction of 27 Mt/y of Green House Gas (GHG) emissions, plus considerable water savings due to lower water cooling requirements and less fossil fuel consumption."

Jan 1, 2011

By Robert G. Robins

Precipitation of ferric arsenate is an effective method for removing arsenic(v) from hydrometallurgical process solutions. The solubility and stability of this compound. FeAs04.2H20, has received some attention in recent years and the reported solubilities of amorphous and crystalline material have varied considerably. This paper reviews previous studies and reports some recent work with a consistent model to explain the variable results. Free energy data for ferric arsenate and its associated dissolved complexes are presented.

Jan 1, 1990

By John C. Carpenter

Solvent extraction is used to selectively recover copper from iron containing sulphate solutions. As chloride ions, which form series of complexes with transition metals, are now being used for leaching. Little is known of the effects of these ions, on solvent extraction behavior. It has been shown that commercial extractants of the L1X and Kelex series extract copper from chloride media: (1) at a lower pH than from sulphate solutions, (2) to similar loadings, and (3) except for L1X 63, without transferring chloride to the organic phase. A process for selective extraction of copper from chloride solutions should thus be compatible with standard stripping and electrowinning practice. Of several diluents, differing in aromaticity, kerosene gave enhanced extraction only with L1X reagents. A change in operating temperature had little effect on equilibrium metal distribution. All the extractants examined gave adequate separation of copper from iron. L1X 63 was found to extract chloro-complexes of copper and of iron and thus transfer chloride to the organic solution. Consequently this extractant and its mixtures are not preferred for use with chloride leaching systems.

Jan 1, 1976

Acid mine drainage containing heavy metal ions is a large environmental problem facing the mining and mineral processing industry. The femte coprecipitation is a novel technique for removing heavy metal ions from waste water, recently applied to acid mine drainage. The fenite precipitation is usually performed at high temperature and therefore if applied in conventional manner, it becomes uneconomical to treat large quantities of acid mine drainage. In this paper the ferrite precipitation at ambient temperature-is &died. The possible mechanism of ferrite formation is discussed Experimental results from Noranda Tailing and Berkeley Pit water treated by this process are presented.

Jan 1, 1994

By Peter Stiaszny, Andrej Samoilov, Yuri Titovets, Gottfried Hribernig, Nikolai Zolotorevskii

"The model has been developed to simultaneously predict both transformation product portions and mean ferrite grain size from the same common · principles as a result of the austenite decomposition during any cooling path of dual phase steels. The transformation products considered are polygonal ferrite, pearlite, bainite and martensite. The model is based on the classical equations of nucleation-growth theory and also contains some empirical parameters. The chemical driving forces for nucleation and composition of elements at the phase interfaces are derived by computation thermodynamics. The empirical parameters related to the model were determined on the basis of a series of austenite transformation dilatometric curves and grain size measurements for continuous and interrupted cooling of several steel types. The model is aimed to predict phase transformation in the complex cooling conditions of the run-out table of the hot strip mill at YOEST-ALPINE STAHL LINZ GmbH as a part of the computer aided system for prediction and on-line controlling of the mechanical properties of hot-rolled strip.IntroductionThe term ""dual phase steels"" is used to refer to a steel consisting essentially of a dispersion of martensite in a fine-grained ferrite matrix. These steels are of increasing technological interest since they provide a better combination of strength and ductility than any other conventional steel sheet material. The strength is important because it offers an opportunity to produce lighter components, while good ductility is needed to permit easy forming of components. It is generally recognized that martensite plays an important role in determining the strength level of dual phase steels. A full understanding of the role played by the phases in determining such characteristics requires investigating in more detail how to optimize the martensite level of such steels, while maintaining good ductility remains the subject of continued research in the industry."

Jan 1, 2000

Two pilot-plant investigations were conducted in which strong-base resins were compared with activated carbon for the extraction of gold cyanide from leached pulp from the Golden Jubilee Mine. The results show that gold can be recovered with carbon, but that the extraction efficiency is poor, probably because high concentrations of humic and fulvic acids are. present m the pulp. .However the extraction of gold cyamde from this material with strong-base resins JS very effo:1ent, and the overall efficiency of extraction is better with resin than with carbon, even when the concentration of resin is one-third that of carbon, and the flowrate of resin is one-third that of carbon. The results of the pilot-plant campaign reported in this paper led to the conversion of the Golden Jubilee plant from carbon-in-pulp to resin-in-pulp in February 1988.

Jan 1, 1989

By Mark R. Jolly, Jean-Christophe Gebelin, Aleksander Cendrowicz

"Injection of wax patterns is the first stage of the multi-stage process of investment casting. The quality of the final casting and its dimensional accuracy is highly dependent on this stage of the process. Pattern waxes used in the industry behave in a complex visco-elastic-plastic manner. The modelling of such material behaviour is therefore not simple.In this paper a number of configurations of die will be shown in which the injection of the wax has been carried out for a range of processing conditions. Some of the dies are transparent and the movements of wax front observed can be compared with those predicted by simulation. Surface defects in final components will also be shown and compared with the location predicted by simulation software. Some discussion will be presented on the limitations of the software used and the time-scales achieved for practical use as a design tool within the foundry environment. IntroductionThis paper presents the research activities carried out at the University of Birmingham on the modelling and prediction of the behaviour of industrial investment casting waxes during the injection of wax patterns. These research activities are done in the context of a more global study of the fundamental aspects of the investment casting process, the FOCAST project. Regarding the wax injection process, the aim of the project is to achieve a better understanding of the key factors that will lead to better castings. The filling of the die during the injection has been studied. Some other phenomena such as shrinkage/warpage or creep under residual stresses are also studied, but not presented here. Two commercial investment casting waxes have been characterised in order to model their behaviour and predict mould filling and subsequent defects.This paper will present the models that have been used in our work, the simulation packages used, the experiments carried out to validate the modelling and exhibit the defects due to bad filling, and finally the numerical simulation results."

Jan 1, 2001

The Kaldo furnace smelting technique was developed for oxygen steel production by the late Prof. Bo Kalling, Domnarvet, Sweden. Development started in 1948, and production in 1956. Five million tons of steel were produced in TBRC's in 1973. Mainly due to high TBRC maintenance costs, the steel industry now prefers non-rotating converters. In non-ferrous metallurgy, however, qualified new applications of the TBRC technique have been realized or are being considered. Inco, Canada, succeeded to convert nickel matte to metal in the Domnarvet pilot plant in 1959, and have now installed a commercial plant in Copper Cliff. La Metallo-Chimique, Belgium, has pioneered secondary copper smelting and refining in the TBRC, operating plants in Beerse, since 1968, and Alton, U.S.A. Peko-Wallsend Ltd., Tennant Creek, Australia, was faced with the problem of producing saleable blister from concentrates containing 1.5-2.0% Bi. The flash smelting matte, containing 0.2% Bi, could not be refined to an acceptable limit of 0.03% Bi in the blister copper in a Peirce-Smith converter. Tests at Domnarvet indicated that a TBRC would achieve satisfactory bismuth elimina- tion. Two TBRC's were installed in Tennant Creek and operated for 14 months during 1974-75. The problems encountered and how they were over- come are described. Further TBRC applications have been studied in Sweden.

Jan 1, 1976

By Carlos Antonio da Silva

Steel refining reactors based on chemical heating are being used as an alternative to ladle furnaces. They show a high degree of flexibility in respect to heating rate in addition to carrying out refining reactions such as de-S, inclusion removal, alloying etc. IR-UT and CAS-DB are examples of such reactors. Their performance is dependent upon geometrical characteristics as well as operational conditions which determine the flow field inside the vessel. A physical model of the IR-UT process of the Companhia Siderurgica de Tubarao, steel plant located in Serra, Espirito Santo, Brazil, was developed to assess the features of the flow field and its influence on the metallurgical behavior. Results of the physical model were used to optimize the process parameters in the industrial unit.

Jan 1, 2003

By C. Camurri

Results from the Metallurgical Department of Universidad de Conception showed that fire-refined copper could be rolled without previous remelting for deoxidation. The goal of this work is to determine the rheology of fire-refined copper from tensile tests at different temperatures and strain rates, and Ford plane compression tests. All that in order to simulate and calculate rolling process variables. For rheology hardness coefficients, n variables between 0.28 at 600°C and 0.46 at ambient temperature are obtained. The sensibility coefficient for strain rate m varies between 0.056 at 600°C and 0.006 at ambient temperature. The activation energy for plastic flow Q in the considered temperature range is 1436 cal/mol.

Jan 1, 1999

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Guohua Bai, Mingjun Rao, Jianchen Lim, Guanghui Li, Tao Jiang

"By using thermogravimetry, optical microscope and chemical phase analysis, the solid-state reduction of carbon-burdened chromite pellets in the absence and presence of additives were investigated. The effects of reduction temperature, reduction time and additives on the metallization of chromite pellet were studied. The results indicate that the pre-reduction ratio of carbon-burdened chromite pellets is improved with the increase of reduction temperature and the addition of additives. The metallization of chromium is increased from 63.9% to 92.8% at 1300 °C for 4h with the addition of 2 wt.% of sodium borate. Investigation suggests that the reduction of carbon-burdened chromite pellets is diffusion controlled. The apparent activation energy without additive is 192.1 kJ/mol, while it decreases to 170.4 kJ/mol in the present sodium borate.IntroductionFerrochrome is used to produce high strength, corrosion resistant, wear-resisting, high temperature resistant and oxidation resistant special steels, and it is becoming one of the most important alloy materials for the production of stainless and high alloying ferritic steels [1-5]. Demand for ferrochrome is steadily on the rise due to the growth of stainless steel industry. Nowadays, more than 80% of the world's ferrochrome is utilized in the production of stainless steel [6-7].Ferrochrome is mainly produced in submerged-arc furnaces (SAF) with chromite lump ore. However, lump ore merely accounts for 20% of the chromite ore output, while fine ore (< 8 mm) accounts for about 80% [8]. Therefore, agglomeration of chromite fine ore is necessary before charging into SAF."

Jan 1, 2011

By Edward Peters

Scandium (Sc) has unique properties and is one of the more valuable elements in the periodic table. Scandium can be used in solid oxide fuel cells and to produce high strength aluminium alloys of value, for example, in the aerospace industry. Scandium is often grouped together with the rare earth elements (REE). Amongst others, scandium can be found in bauxite residues, so called red mud. It is possible to extract and enrich scandium from red mud by leaching and solvent extraction. Scandium can then be recovered from the pregnant strip liquor by crystallization. The strip liquor will however still contain certain impurity elements. In the present work, a method for obtaining a pure scandium solid phase by direct crystallization from the strip liquor is evaluated. It was found that Fe and Ti co-precipitate with Sc under the conditions employed.