Search Documents

By Sergio N. Monteiro

Jute fabric obtained from discarded sackcloth is a promising low cost and post-used material being considered as reinforcement of polymeric matrix composites. In particular, the combination of this fabric with a recycled plastic constitutes an environmentally correct composite with both economical and environmental advantages. The present work investigates the toughness of recycled polyethylene composites reinforced with up to 40 wt% of post-used jute fabric extracted from discarded sackcloth. Standard Izod notched specimens were impact tested and the results showed an increase in toughness with the amount of jute fabric. Observation of the composite fracture by SEM revealed that the fabric weave, in spite of damages caused by the previous use of the sackcloth, act as an effective obstacle to crack propagation.

Jan 1, 2009

By A. J. Duncan, S. Viswanathan, Q. Han

"Measurements of liquid permeability in the mushy zones of Al-15.42% Cu and Al-8.68% Cu alloy samples have been performed isothermally just above the eutectic temperature, using eutectic liquid as the fluid. A modified method has been developed to determine the specific permeability, Ks, as a function of time during the test from the data collected on these alloys. Factors affecting permeability measurements are discussed. Permeabilties are observed to vary throughout the experiment. This is attributed to rnicrostructural coarsening and channeling that occurs in the sample during the experiment. The permeability is related to the rnicrostructure of the sample using the Kozeny-Carman equation. The correlation between the measured Ks, liquid fraction, gL and the specific solid surface area, Sv, improves markedly when compared to previous studies in which rnicrostructural coarsening was ignored.IntroductionThe permeability of interdendritic liquids flowing through dendritic structures ·is an important parameter needed to predict the level of porosity in castings. The permeability is a component of Darcy's Law, used to estimate the pressure drop due to the resistance to the flow of interdendritic fluid to feed shrinkage. Therefore, much research has focused on measuring the permeability of alloys in the mushy zone (1-10). The Kozeny-Carman equation for liquid permeability in the mushy zones of alloys may be written as"

Jan 1, 1999

By Sun-Hee Cheong

This study sought to produce L(+)-calcium lactate using precipitated calcium carbonate as a starter culture composite of lactic acid bacteria in lactic acid fermentation. Specifically, precipitated calcium carbonate was synthesized by reacting calcium hydroxide with sodium carbonate in the previous study by the authors. Synthetic precipitated calcium carbonate was then used as the calcium source of lactic acid bacteria during the fermentation process. In general, precipitated calcium carbonate has low absorption rate in the human body. On the other hand, calcium lactate has high absorption rate; it is commonly used in food and drug industries as calcium additives in various foods such as cookies, beverages, bread, sauces, powdered milk, and fruit juice. Calcium lactate has two racemates, e.g., L(+)-lactate and D(-)-lactate. In particular, L(+)-lactate is known to be more soluble than D(-)-lactate and generally produced from lactose by homo-fermentative lactic acid bacteria such as Lactococcus spp., Lactobacillus plantarum, Lactobacillus casei, Lactobacillus curvatus, and Pediococcus spp. Thus, the characteristics of the pertinent lactic acid bacteria and optimal condition such as temperature, pH, precipitated calcium carbonate addition rate, and content of fermentation for increasing formation yield and purity were investigated. The findings suggested the possibility of manufacturing L(+)-calcium lactate using precipitated calcium carbonate as a calcium source with high value-added instead of commercial calcium lactate.

Jan 1, 2006

By Tejs Vegge

The lack of suitable means of storing hydrogen for use in the transport sector is generally viewed as a primary showstopper for a hydrogen economy. Recent developments within solid state hydrogen storage in complex hydrides and metal ammines have sparked new hope of a long term solution, but as of now, no materials fulfill all the DoE targets for onboard storage [1]. A detailed physical understanding of the ab-/desorption processes and the role of the essential catalytic additives is an essential prerequisite for the development of new optimized hydrogen storage systems. Here, we illustrate the potential of utilizing the synergy of combining state-of-the-art in theoretical methods and experimental techniques in the analysis and design of materials for hydrogen storage. Recent advances in computer hard- and software has made it possible to treat many of the essential problems in such materials, i.e. structural stability, hydrogen dissociation and diffusion, with high accuracy methods like density functional theory. We rely on such results to guide our synthesis of new materials, and to interpret our experimental results from, e.g. time dependant in situ x-ray diffraction, synchrotron/neutron experiments, and advanced materials testing. Through a continuous feed-back optimization loop between theory and experiments, the obtained nano-scale insight is used to expedite the design and development of novel materials for hydrogen storage.

Jan 1, 2006

By M. A. Barron, D. Y. Medina, R. T. Hernandez, I. Hilerio

"Chromium Nitride (CrN) thin fihns were deposited on steel AISI 316 substrates with reactive magnetron sputtering method. CrN films were produced under two different conditions. In the first one, the substrate was heated by a d.c. source. At the second coating was applied a negative substrate bias voltage. X ray diffraction, quantitative energy dispersive and scanning electron microscope, were employed to characterize their phases, chemical composition and microstructure. Additionally microhardness was evaluated using a microhardness tester. The results show that the phase formation of CrN thin films in the first case (with temperature) is better. Both coatings presented homogeneous surface. Their compositions shows differences though that gases flow are same. In attention to their hardness, presents an increment if it's compared with hardness substrate.Nomenclature.P Ar =Argon gas pressure during coating.PN2 = Nitrogen gas pressure during coating.Ts = Substrate temperature during coating.T f = Coating melting temperature. (CrN = 1050°C).E=Potential difference.t =Coating time.P=Target power (Cr) in magnetron sputtering de.HV = Vickers hardness.F = Applied charge.d= Average length of longitude of the two diagonals (mm)Introduction.Wear causes losses in materials surface, generating that components of mechanical systems suffer irreversible changes in their properties, causing a faulty operation of the system. It is important to control their effects, measuring and interpreting their causes clearly."

Jan 1, 2013

By Marco Olper

The CX-EW technology, developed by B.U.S Engitec, is improved introducing besides the battery paste electrowinning, the direct electrorefining of metallic lead (grids and poles) obtained from CX breakers. This new concept of electrorefming the antimonial lead scrap is aimed to the production of 99.99 lead and of slimes with high antimony content, avoiding gaseous emissions in melting lead scrap, and expensive and pollutant thermic refining operations. In this way, practically all lead content in the battery is available as 99.99 lead, hence with a wider market for the lead recyclers. This paper will describe the tests performed on a pilot plant scale with special reference to the relatively low energy consumption of the process.

Jan 1, 1993

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By T. S. Bannos

Section 1417 of the Safe Drinking Water Act Amendments enacted by the O.S. Congress prohibits the use of lead containing solders for potable water systems in new construction or when making repairs. The legislature defines "lead-free" solder as containing less than 0.2% lead. In the development of a new solder it was recognized in addition to the lead free requirement, the alloy should perform as well as the popular 50/50 tin lead solder, both in application and properties. Another objective was to have only nontoxic elements. This led to the development of a 4.0% copper, 0.5% silver and 95.5% tin solder. Review of the merits of other alloy systems and the development of the physical properties along with test data are presented for the lead free tin. rich alloy.

Jan 1, 1990

By Tabbetha A. Dobbins

We report studies concerning the time frame for catalytic reactions between NaAlH4 (sodium alanate) and TiCl3 during high energy milling. Spectral features in x-ray absorption spectra were analyzed for samples milled for various times (0 minutes, 1 minute, 5 minutes, 25 minutes, and 125 minutes). A structural transition from Ti3+ to Ti0 is observed within the first 5 minutes of milling. The Ti0 structure persists for samples milled for times longer than 5 minutes?even after those samples underwent a subsequent single hydrogen desorption/absorption cycle. Samples milled for less than 5 minutes retain Ti3+. For samples milled for 1 minute, the Ti-K edge position shifts from Ti3+ to Ti0 after a single desorption/absorption cycle. However, the first coordination sphere around the Ti0 absorber occurs at longer distances for 1 minute milled sample. These results hint at the formation of Ti0 pure metallic clusters upon desorption/adsorption cycling of 1 minute milled sample. Previously reported x-ray absorption spectroscopy studies have demonstrated the structural transition from Ti3+ (in TiCl3) to Ti0(determined to be TiAl3 found at the surface of the alanate powder). Aluminum deficiency on the NaAlH4 lattice is responsible for controlling hydrogen absorption capacity. These time-resolved spectroscopy studies suggest the possibility for controlling aluminum deficiency, while still maintaining titanium activation of the alanate powder, by manipulating the coordination environment of the titanium dopant during the first five minutes of high energy milling. Specifically, a possible approach to mitigating aluminum deficiency during doping would be to introduce an alternative species to which the to Ti3+ catalyst would form a metallic bond after the TiCl3 has attached at the surface of the sodium alanate powder and before the Ti3+ forms the TiAl3 intermetallic species.

Jan 1, 2006

By I. Ohnaka

Although many works have been reported on the semisolid casting, the mold filling behavior of semi-solid alloys has not been so well understood. This paper compares the physical and numerical simulation results on the mold filling behavior. Physical simulation was performed by using solid-water mixture. The numerical simulation was made under the assumption of one phase flow with an effective viscosity. It was found that the solid particles stabilize the flow greatly if the kaction solid exceeds about 0.4, because viscosity increases greatly. The overall flow behavior can be estimated by the numerical simulation. Interesting flow behavior was also found which can not be observed in the case of one phase flow and which is difficult to simulate by the one phase flow assumption.

Jan 1, 1997

By Huimin Lu, Lian Zhou, Qiang Li

"A three-dimensional mathematical model is developed for the regenerative rotary hearth furnace with 40 meters medium diameter. The influence of combustion switchover and outlet pressure on the fluctuation and distribution of temperature and pressure is studied with numerical simulation method. The results showed that the temperature field and flow field is suitable for requirement of industrial production; the fluctuation of the temperature field and pressure is acceptable; the influence of outlet pressure on the furnace pressure is great.IntroduceRotary hearth furnace which is originally utilized as heat treating and reheating industrial furnace, now is also used for carbon based DRl production. With the need of market and the concern of resource recycling and environmental issues, the DRl production from ore or from waste material by rotary hearth furnace attracts more and more attentions from steel industry [1,2].When rotary hearth furnace works, the feed pellets are charged on the hearth and rotate within an annular furnace chamber with the process of reduction. For the sake of rapid reduction, usually the depth of the pellet is one or two layers, accounting for less than 90% of the volume of furnace. As result, the exhaust gases carry away a lot of heat, so that energy utilization efficient is low [3]. Currently, in order to reduce the consumption of energy and improve the production efficiency, many methods have been adopted. The regenerative combustion technology is one of the most promising."

Jan 1, 2013

By Junji Shibata

Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni, 0.1 kglm3 Fe, 0.0 I kg/m3 Zn, 48 kg/m3 S042-, 98 kg/m3 HP032-and 31 kg/m3 laetic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods are possible to use for the treatment of this kind of solution. In this study, solvent extraction of Ni was investigated using two kinds of extractants to clarify the relation between extraction percent and pH for various extractant mixtures. As Ni ion has an octahedral structure with ligands, the synergistic effect for Ni extraction is considered to take place in solvent extraction using two types of extractants. The investigation of the synergistic effect for Ni extraction was carried out in case of various extractant systems.

Jan 1, 2003

By C. B. Solnordal, R. N. Taylor

"The heat transfer conditions on the outer side of a Sirosmelt lance have been determined using experimental measurements in combination with a mathematical model. By measuring the temperature distribution along the wall of an operating Sirosmelt lance, as well as the thickness of the slag layer on it, it was possible to use the model to determine both the heat transfer coefficient between the vessel contents and the lance, as well as the effective thermal conductivity of the slag layer. The effective thermal conductivity of the slag layer was found to be within the range 0.7-1.3 W.m-1. ºCl, which was in good agreement with measured values for magnetite. The outside heat transfer coefficient varied from 80 to ISO W.m-2. ºC1, which was smaller than quoted in the literature for metal/slag systems. The discrepancy was attributed to the high thermal resistance experienced between the lance wall and the slag layer, as well as the large quantities of combustion gases that envelop the lance tip and reduce convection and conduction from the melt to the lance. INTRODUCTIONThe Sirosmelt submerged combustion smelting process [1] utilizes top injection lances to deliver fuel and air into a metallurgical melt. To help prevent lance failure from attack by liquid slag, helical vane swirlers are used within the annular lance to impart swirl to the flowing air and enhance the heat transfer from the lance wall to the air. The swirlers thus cool the wall, and enable a frozen layer of slag to form on its outer surface. This solid layer ensures liquid slag cannot reach the lance surface, and the lance is protected.A mathematical model of the heat transfer processes associated with the lance has been developed, which combines heat balance equations with engineering correlations to predict the wall and cooling air temperature of the lance, as well as the air pressure distribution. An account of the model was given by Rankin et al. [2]. To further enhance the model and enable it to predict the thickness of slag accumulating on the lance, a detailed analysis of the heat flow through the slag layer commenced in 1992. By far the most complex aspect of the model, the flow of heat from the vessel contents to the outside of the lance was dependent on many factors, including:-"

Jan 1, 1996

By Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, William Gleason, Maureen Chorney

Experimental and industrially produced polystyrene and silica resins are tested for recovery capabilities of Rare Earth Elements (REE). Testing regimes being used are typical of resin analysis. Inductively Coupled Plasma-AES results indicate that preferential separation and recovery is possible in the adjusted pH range of2 to 10, solution conditions, and resin type. Testing conditions are resulting in structure modification of the composite resin as indicated by X-Ray Diffraction, Differential Scanning Calorimetry, Scanning Electron Microscopy, Mercury Porisometry, and density analysis. Resin modification indicates both surface and internal structure alteration outside of reported standard behavior of resins. Structural changes have ramification for both Rare Earth Recovery RER and traditional resin operations. Analysis shows that the resin uptake of REE can be manipulated for concentration. Further analysis with SEM work indicates that widespread surface and interior modification is taking place as resins load with REE. This modification is leading to pore rupture and particle breakage. Further investigation is being performed to determine the mode of breakage.

Jan 1, 2015

By Afshin Sadri

Acousto Ultrasonic-Echo (AU-E) is a technique developed to provide accurate measurements of the refractory lining wear in operating smelters based on the principles of stress wave propagation. The objective of the system is to provide feedback for the continuous optimization of the overall smelter operation. In some cases, the AU-E refractory lining measurements have allowed clients to extend their smelter campaigns and operate safely for several years beyond their planned reline schedule. In other cases, AU-E results inform clients of serious issues within their furnace allowing them to shut down their smelters ahead of predicted failures and possible disasters. This paper presents the results of several smelter AU-E inspections of the hearth and sidewall. These case studies demonstrate how the AU-E results were used to positively affect the smelter operation.

By Robert W. Bartlett

Chalcopyrite in copper flotation concentrates can be hydrothermally converted to digenite with oxygen in a continuous process, with rapid kinetics when operated above 200°C. This eliminates large amounts of sulfur and iron. These "super-concentrates" have potential for debottlenecking smelters and avoiding capital intensive future smelter expansions, otherwise required in the late 1990s. The technology of producing super- concentrates is described, with cost estimates, and the use of super-concentrates as smelter feed is discussed, with examples.

Jan 1, 1992

By Katie Schumacher, Greg Roset, Dayle Flynn

The Columbus Processing Complex of the Stillwater Mining Company began operations at Columbus, Montana in 1990 based on electric furnace smelting treating a precious metals concentrate from the nearby Stillwater mine and mill. Since that time, the smelter plant has been expanded in stages in order to treat recycled materials in addition to the concentrate. This paper describes a number of changes made at the plant to effectively handle recycled materials.

Jan 1, 2014

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment .step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1M sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250 °C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 1995

By R. Gampala

The consolidation of mom matrix composite monotapes occurs by the plastic (time independant) and creep deformation of monotape asperities. Past models of the process used seperate micromechanical analyses of the contact deformation by (rate independent) plasticity and power law creep (i.e steady state creep). These models are now used to simulate consolidation and to optimize/control consolidation process cycles so that the composite's microstructure is "steered" to, a user defined goal state. However, the models do not incorporate the sometimes dominant transient creep process and the instantaneous response of the plasticity mechanism causes finite discontinuities in the microstructure state vector field and therefore eliminates the possibility of using the powerful array of trajectory optimization schemes that all require continuous vector field for optimization and control. To overcome this problem, a inified creep/plasticity constitutive model that results in a continuous state vector field is used to rederive the contact deformation response during monotape consolidation. The contact blunting of a laterally constrained hemispherical asperity is first analyzed and its response represented by two coefficients; one relating the contact area to the blunting strain (C), the second, the mean contact pressure to the blunting rate (F).The C and F coefficients for this unified blunting problem are then obtained by finite element analysis, and detailed results presented for two composite matri-ces of topical interest (Ti-24A1-11Nb and Ti-6Al-4V).

Jan 1, 1996

By Ximena Diaz

Mercury is one of the most undesirable contaminants in gold bearing ores. During cyanidation mercury cyanide compounds accompany gold in all the extraction and recovery processes. Of course mercury in the carbon eluates creates environmental problems in subsequent refining steps. One possible process alternative for the separation of gold from mercury in such concentrated alkaline cyanide solutions is the selective solvent extraction of gold by undiluted Dibutyl Butyl Phosphonate (DBBP). In order to describe the behavior of mercury during extraction by DBBP, the results from a preliminary research program are presented. In this study, temperature and cyanide concentration have been found to be the most significant variables which influence the separation of gold from mercury by solvent extraction using DBBP. It was found, using plant eluate from a carbon strip, that excellent separation of gold from mercury can be obtained at 60' C with 98% gold recovery and complete mercury rejection in a single stage of extraction. The influence of pH is also discussed in terms of the extraction chemistry. These results complement previous research which described the DBBP solvation extraction of an aurocyanide ion pair. In addition, these results extend our understanding of the alkyl phosphorous ester extraction systems by illustrating that neutral ionic species such as Hg(cN)02sq, can be extracted at low cyanide concentrations, a phenomenon which had not been observed previously for other cyanoanions.

Jan 1, 1993