Search Documents

By Manuel Caro

El presente trabajo describe el proceso de mantenimiento del equipo de aire denominado Optiair. Este filtro al tener una mayor capacidad de retención de polvo, permite que el equipo pueda trabajar por periodos más largos sin tener que detenerse para realizar el cambio de filtros, lo cual incrementa el factor de disponibilidad del equipo. Entre los beneficios principales tenemos: el incremento de salida de aire, menor restricción del flujo, menor caída de presión y una mayor cantidad de contaminante capturado.

Aug 25, 2002

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U. S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. Cambrell and Haynes1 (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and Singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 45°. However, to date, no systematic attempt has been made to establish design criteria. In this paper, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1979

The Department of Mineral Resources has a statutory responsibility for mine site environmental management and control in New South Wales. The Department is focusing on an environmental management systems (EMS) approach, as a management tool to achieve æbest practiceÆ outcomes both within our own organisation and on mine sites. One of the DepartmentÆs tools is environmental risk assessment and management which incorporates the Mining, Rehabilitation and Environmental Management Process (MREMP). The MREMP was introduced many years ago in order to integrate the activities of key stakeholders who may have a material interest in the mine. The MREMP provides an ideal mechanism by which ædue diligenceÆ requirements and environmental management programs can be integrated into mining operations and lead to a sustainable post-mining land use.

Jan 1, 2002

By Wilton Johnson

Native asphalt was produced by three companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm, R. L. White Co., Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Colorado and Utah, was mined by two firms, American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), and Ziegler Chemical and Mineral Corp. Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) closed its mining operation during the year.

Jan 1, 1988

By Jimmy Rodríguez Las Heras

Durante la explotación de los niveles inferiores en la mina Yauliyacu, se generaron dudas sobre la ubicación de las concentraciones de esfuerzos y sus relaciones con los estallidos de roca. En este sentido, se instala un sistema microsísmico donde mediante el análisis de la microsismicidad se elaboró los estándares que permitieron reducir los incidentes por estallidos de roca presente, así como la frecuencia, magnitud y daños a las personas, y equipo e infraestructura de mina, debido a la energía liberada por los eventos microsísmicos. Por ello, el presente trabajo señala los beneficios del uso del sistema de análisis de microsismicidad como la actualización contínua de la zonificación minera de acuerdo a la concentración de esfuerzos, procediendo al reforzamiento del sostenimiento como medida de prevención.

Sep 21, 2013

By A. Uiga

The U.S. Bureau of Mines funded a project which addressed objectives concerning irrigation of native plants and inoculation of native plants with vesicular-arbuscular mycorrhizal (VAM) fungi. The specific irrigation objectives were 1) to demonstrate the performance capabilities of solid-set irrigation for reclaimed mineland conditions, and 2) to demonstrate and evaluate three irrigation concepts under two separate water supply conditions. The VAM inoculations were to assess irrigation benefits in establishing VAM relationships for transplanted native species. Following the seasonal demonstration (May to September 1983) at 3 separate mine sites, conclusions were made that apply to the 6 state Western mining industry. The demonstration sites were located in Montana, Wyoming, and New Mexico. Positive conclusions were reached for 1) the use of soil moisture sampling with or without irrigation, and 2) the selection of solid-set sprinklers as the irrigation method. The conclusions about the irrigation concepts and strategy were mixed, due to the short-term (1 season) nature of the project. No conclusions could be reached for the VAM inoculations because the study time was too short.

Jan 1, 1984

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By Heikki Jalkanen

The mineralogical composition and morphology of solidified copper smelting and converting slags are of some interest from slag cleaning (by froth flotation), impurity elimination, and environmental points of view. Properties result from both the state of molten slag before solidification and processes taking place during solidification and cooling. In solidification and cooling, copper and sulfur dissolved in molten slag are .precipitating substantially from the silicate phase. Even in water quenching of slag, dissolved copper is pushed out of the solution in the form of finely divided precipitate. Elements present in the raw materials are distributed in a distinct manner between the solidified slag and non-silicate solidification products. Arsenic, antimony, and tin are strongly accumulated in copper precipitate, but not the other metallic constituents common in copper concentrates. Smelting and converting slags differ remarkably on their mineralogical composition and morphology although resulting principally of same chemical processes. Converter slags are more inhomogenous; they often contain solid particles and copper content is .as a rule higher than in matte smelting slags. The final copper content of converter slags was observed to be in a distinct manner dependent on iron oxide - silica ratio. Slag forming, solidification, and precipitation phenomena are discussed on the basis of mineralogical and morphology analysis of smelter slags and laboratory scale experiments.

Jan 1, 2002

By Wayne Trudel, Eric Saderhold, Lloyd McEvers, Lori Clarke, Charles Lynn Bolin, Leroy Schutz

Editor’s note: This is the second part of a two-part series on how mine geologists added about 141t (4.53 million oz) at Newmont Mining’s gold operations in Nevada during 2003. Part one (ME, July2004, pp. 19-26) showed how cross-functional teamwork among mine geologists, engineers, metallurgists and operators added $65 million in revenues at Newmont’s Gold Quarry Mine. Part two deals with how this same cross-functional team added about 25.8 t (830,000 oz) of gold reserves and two years of life at the company’s LoneTree Mine. This was done through improved reconciliation methods, pit optimization designs and updated geotechnical parameters. Part two also discusses how Newmont’s Nevada mine personnel added about 62.2 t (2 million oz) of gold reserves at its Twin Creeks Mine, extending the mine’s life by several years. The Lone Tree Mine is a sediment-hosted, micron gold deposit. It is dominantly situated in the Golconda thrust footwall. The north-south trending Wayne Zone fault controls the highest-grade ores and

Jan 1, 2004

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By K. Zipf, Z. T. Bieniawski

"An extensive mixed-mode fracture toughness testing programme was conducted on coal from three coal fields. A special mixed-mode testing fixture for coal and other geologic materials was developed together with reliable specimen preparation procedures. Dynamic modulus measurements made on each of the 116 fracture toughness specimens showed that these coals exhibit certain degrees of anisotropy. The fracture toughness testing programme systematically varied the loading rate, specimen orientation and fracture loading mode. Loading rate did not significantly effect the fracture toughness over the quasi-static range tested. Orientation did have a significant effect on measured fracture toughness. In the coals tested, the divider orientation and arrester orientation had higher fracture toughness than the short transverse orientation. Data showed that one orientation could have almost twice the fracture toughness as another. The fracture toughness testing enabled certain evaluations of three mixed-mode fracture theories: maximum tangential stress, maximum energy release rate and strain energy density theory. Due to the extreme heterogeneity of the coals tested, definitive conclusions regarding the best mixed-mode fracture theory are not possible; however, data do tend to support the strain energy density theory. INTRODUCTIONThe major aim of this research is to ·develop a fundamental understanding of how fine· fragments of coal (respirable dust) are generated during a fracture process. In a related paper [l], a hypothesis was presented for the mechanism of fine fragment formation during a generic coal material/cutting tool interaction. In this hypothesis, fine fragments are created during coal material/cutting tool interactions that are best described as general mixed-mode fracture processes. Data are required on the mixed-mode fracture behaviour of coal, the physical character of the newly-created fracture surfaces and the character of the inherent flaw structure of the coal material. Accordingly, a test programme was designed that provided some information in each of these areas. The testing effort seeks to measure critical fracture toughness under mixed-mode loadings as a material parameter characterizing in part the tendency of various coals to generate undesirable quantities of fines and respirable dust."

Jan 1, 1990

The maximum current density at which conventional copper electrowinning plants will result in satisfactory, adherent, and dendrite·free cathodes is determined by the thickness of the diffusion boundary layer. A decrease in the value of that thickness will permit an increase in the current density. This fact is utilized to develop a high current density cell in which the reduction of the boundary layer thickness is accomplished by means of a specially designed electrolyte circulation system. The high current density cell is used to determine the effect of current density on such process parameters as current efficiency, cell voltage, power consumption, and cathode purity. A number of empirical equations are developed for the purpose of estimating the magnitude of these effects.

Jan 1, 1972

By Lon A. Williams

This report, authorized under Contract Number H0220065, Amendment Number Six, documents the results of an investigation of lighting system modifications and designs for working place illumination in high and low coal entries of underground coal mines. The portable and machine mounted system designs, both modified and prototype, represent a continuation of work performed under Contract Number H0111403, Amendment Number One. See the Final Technical Report dated May 26, 1972 for detailed information concerning this prior Contract. All modified and prototype systems met the performance requirements of Bureau of Mines Specification 2G, as proved by test. In addition, the systems met the requirement for illumination, as specified in the Contract and in the proposed standards which were generated in response to Public Law 91-173.

Jan 1, 1976

By V. Petr, G. G. W. Mustoe, T. G. Rozgonyi

We introduced a numerical method that is applicable for the analysis of static and dynamic deformations of elastic media. In this numerical study, each elastic body is modeled with a system of several hundred rigid particles that are joined together elastically. Maximum shear stress fields due to external loading are obtained and compared with those obtained by photoelastic experiment. Preliminary results are presented for the stresses generated in circular disk shaped bodies idealized with connected systems of particles. Extension of this simulation method to fragmentation of brittle materials is also illustrated in an example.

Jan 1, 2000

By Sabri Ergun

This report gives the result of investigations of coals of different rank, coal com¬ponents, chemically and thermally treated and irradiated coals, and sedimented organic matter. In most studies the arbitrary parameters obtained from the usual quantitative profile analyses are not given largely because they lack physical meaning. Instead comp interpretations are offered. X-ray patterns of high-volatile bituminous and lower rank coals are not self¬-sufficient for structural interpretation by the methods of analysis developed to date. The patterns of hydrogenated and dehydrogenated coals indicate that the basic change in the structure of bituminous coals with increase in rank is the conversion of alicyclic structures into aromatic layers. In low-rank anthracites the aromatic layers are about 10 A in size. The increase in rank is the result of coalescence of layers. High-rank anthracites have layer sizes of 25 to 40 A and exhibit the development of three-dimensional (hkl) reflections of graphite, indicating ordering of adjacent layers. In meta-anthracites the layers are > 1000 A and the basic structure is that of defective crystalline graphite. The well-known petrographic components in low-rank coals have different structures; the differences dissappear in low-volatile bituminous and higher rank coals. The patterns of sedimented organic matter, except impsonites, differ from those of coal hydrogen contents are high, and their X-ray patterns are consistent with those of structures. In contrast to normal coals, the patterns of uranium-bearing coals show increased diffuseness with decrease in hydrogen content. The diffuseness is accompanied by increase in the uranium content of the coal. It is very likely that high uranium-bearing coals have predominantly tetrahedral structures.

Jan 1, 1968

By David Dardick

Tround International Inc. is developing rock excavation and drilling devices which utilize a simple patented mechanism for firing frangible projectiles. This system launches a salvo of three projectiles with every shot in automatic sequence. Studies conducted by Physics International Inc. have demonstrated that firing projectiles into hard rock such as granite creates fragmentation which is much faster and cheaper than conventional drilling and blasting. The Tround salvo approach enhances this further by a controlled stresswave interaction created by a slight time difference during impact of the individual projectiles. The University of Maryland is conducting additional studies to optimize these parameters.

Jan 1, 1981

Standards And Laboratory Monitoring In Gold Assay Key Components Of Best Practice

Jan 1, 2005

Esso-BHP have installed a production supervisory control system that is presently controlling the offshore oil and gas facilities on the Barracouta and Marlin platforms from an onshore master station. This control is achieved with a computerized master station onshore which uses a UHF radio system for telemetry and control.The system is designed to control, monitor, and gather data from a large number of oil and gas production platforms and has flexibility to handle future variations in operating conditions.The system will be extended to the Halibut platform late in 1970 and to the Kirlgfish platforms during 1971.

Jan 1, 1971

By N. C. Saxena, S. K. Puri, A. K. Pal

The condition-based monitoring system is an important innovation for reducing the downtime of costly, heavy earth- moving machinery (HEMM). Vibration severity measurements were made on the HEMM located at the Gevra Project, the largest coal opencast project in India. Whenever the vibration severity levels exceeded the permissible limits, necessary actions were taken to replace the defective parts of the ma- chine. The systematic vibration monitoring of 120-t (132-st) dumpers, followed by corrective measures led to a substantial increase in component life (8.18% for an 445E Dressor and 28.44% for an MK-30 Unit Rig). The associated costs (including spareparts) were reduced by 21.55% and 25.74%, respectively. Because of the reduced downtime, savings for these two dumpers over the period from March 26 to June 25,1998, were of the order of Rs.26.47 (US$0.649) million.

Jan 1, 2000

By T. Lane Carter

(Canal Zone Meeting , October , 1910.) INTRODUCTION. IT is a curious fact that while in our Transactions there are papers dealing with mining-districts in all parts of the world, in Europe, Asia, Africa, and Australia, there is not one which describes the mining possibilities of Nicaragua; our near neighbor. To be most interested in distant objects, like the moon, .and to neglect what lies at our feet, appears to be a trait of human nature. The neglect of Nicaragua is not confined to the American Institute of Mining Engineers. In no other transactions am I :able to find papers dealing with mining in Nicaragua, some parts of which are as much in need of discovery and research as the North Pole.. I hope this paper will be the precursor of many others to be printed in our Transactions, dealing not only with the mining possibilities of Nicaragua, but with the whole of Central America, where there are vast areas awaiting skill and capital for their development. Much of this capital and skill should come from the United States in the future, although it is probable that European capitalists, when they appreciate fully the possibilities, will investigate more and more the mining-resources of Nicaragua and other Central American republics. Fig. 1 is a sketch-map of Nicaragua showing the principal mining-districts. II. HISTORY. Mining in Nicaragua did not begin yesterday. It was commenced by civilized man when the Spanish conquerors penetrated into the interior and forced the natives to procure the precious metal for them. It is strange that the Spaniards did not find more gold, and work on a scale as extensive as in Colombia and other parts of South America. Probably in Nicaragua the Indians covered up most of the rich prospects

Dec 1, 1910