Search Documents

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By S. Assemi

Interaction forces between a hydrophilic silica particle and an air bubble were measured by atomic force microscopy using simplified model systems with deionized water and dilute KCl solutions. Contributions from the hydrodynamic force were minimized by using a low piezo speed. Particle-bubble separation distance and the bubble spring constant were calculated from linear regression of the piezo extension versus cantilever deflection. The bubble surface potential was then estimated from fitting the AFM-measured forces to the Hogg-Healy-Fuerstenau (HHF) model, using the surface element integration (SEI) method. Surface potentials obtained for the bubble at a low applied force were comparable with the literature data, suggesting that the simplified model used here can give a reasonable estimation of the bubble surface potential under moderate applied forces. Interaction forces between a silica particle and an air bubble were also measured at different locations on the air bubble surface. The force curves obtained at the edges of the bubble fitted very well to the theoretical force curves regardless of the applied force, while curves obtained at the center and halfway to the center, were more difficult to fit, in particular at higher applied forces (> 13 nN), suggesting that force curves obtained at the edges of the air bubble might be less prone to deformation effects.

Jan 1, 2008

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nomnetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By Spencee L. Willett

A sand and gravel deposit exists in the Wildrose Canyon Wilderness Study Area (WSA), Out it is limited to local use because of the distance from major markets and resulting high transportation costs. The WSA has no identified metallic minerals, oil, gas or other energy related deposits. INTRODUCTION The WSA encompasses 17,366 acres (7,028 ha) in the Panamint Range, Inyo County, California. Access to the area is by State Route 190, approximately 45 miles (72.4 km) east of Lone Pine, California and 16 miles (26 km) southwest of Stovepipe Wells, California (fig. 1).

Jan 1, 1983

By Jeffrey W. Fergus, Shiqiang Hui

"Aluminum is an important alloying addition to the zinc used in the hot-dip galvanization of sheet steel to control the properties and appearance of the resulting coating. Optimization of the galvanization process requires control of the alloy concentration which can be improved through the use of chemical sensors. Aluminum sensors based on molten electrolytes are commercially available but are not widely used because of their high cost. One approach to reducing the cost is to use a solid electrolyte which can simplify the sensor design and thus reduce the cost of fabrication. In this paper, the development of an aluminum sensor based on a solid fluoride electrolyte, specifically magnesium fluoride, will be described.IntroductionThe concentration of the zinc bath used in hot-dip galvanization affects the galvanization process as well as the properties of the resulting coating. Thus, accurate in situ measurement of the alloy composition can be used to improve process control. This paper describes a solid-electrolyte-based aluminum sensor for monitoring the bath composition during hot-dip galvanization."

Jan 1, 1997

By Richard Frentress, Dave Donelon, Robert Henderson, Mike Warnert

"The Round Mountain gold mine is an open-pit mining operation located 97 kilometres north of Tonopah in Nye County, Nevada. Gold has been produced from the property since 1906.Gold is currently recovered using a combination of four independent processing operations. These include a 10,000 ton per day mill, a 30,000 ton per day, crushed ore heap leach, a 150,000 ton per day, run-of-mine ore heap leach and a small high-grade gravity concentration circuit. In 2002, Round Mountain Gold Corporation produced 755,494 troy ounces of gold at a total direct operating cost of US$2.14 per ton ($193/oz).This paper presents a summary of the Round Mountain operations and discusses some of the processing innovations that have enabled the mine to profitably recover gold from a large low-grade ore body.INTRODUCTIONRound Mountain Gold Corporation is a 50/50 joint venture between Kinross Gold Corporation and Barrick Gold Corporation. Kinross acquired its ownership interest in the Round Mountain mine upon completion of combination with Echo Bay on January 31, 2003. The joint venture partners continue to support an aggressive exploration program in the vicinity of the mine in order to add reserves and extend the mine life.The Round Mountain mine currently operates a conventional open pit that is approximately 8,200 feet long, 4,900 feet wide and 980 feet deep. Mining is conducted on 34-metre benches by electric shovels and front-end loaders paired with 150, 190 and 240-ton haul trucks. Blasthole samples are collected and assayed and provide the control for ore segregation. Based upon these assays, blasted pit rock is determined to be run-of-mine Dedicated Pad ore, crushed Reusable Pad ore, high-grade ore or waste.Gold is recovered using a combination of four independent processing operations. These include run-of-mine ore heap leaching (Dedicated Pad), crushed ore heap leaching (Reusable Pad), milling and the gravity concentration circuit. Non-mineralised rock is delivered directly to the waste dumps. Low-grade ore is trucked directly to the Dedicated Pad and medium-grade ore is crushed and placed on the Reusable Pad. High-grade ore is handled in one of three ways: 1) leached on the Reusable Pad and offloaded to the mill; 2) sent directly to the gravity plant with tails reporting to the mill; or 3) sent directly to the mill or mill stockpile. The gold particle size distribution of highgrade ore determines the processing method."

Jan 1, 2005

Magnetite cenospheres 40-270 I/m in diameter have been found during the combustion of pyrite concentrate.Micrographs of the surface and internal structures are presented together with comment on the mechanism of forrnation.The similarity to cenospheres found during the combustion of pulverized fuel was noted and speculation raised to their contribution to the dust and fume load in flash smelters.

Jan 1, 1980

By S. M. M. Safvi, A. Jowett

Small-scale continuous flotation tests are described in which the influence of 1) pulp density and 2) feed rate on the rate of flotation are investigated. The results provide further evidence of first-order kinetics for flotation and indicate that tests at different feed rates provide a particularly simple method of determining rate constants. Flotation kinetics are discussed in general terms. Over a period of many years numerous research workers have studied the rate of recovery of valuable materials from flotation pulps with a view to deter-mining the mechanism of the froth flotation process. Froth flo ation is fundamentally a collision process involviug at some stage collision and then mutual attachment between air bubbles and mineral particles. It is possible to draw analogies therefore between the flotation process involving mainly macroscopic particles and the ordinary processes of chemical reaction kinetics involving collisions between atoms, molecules and ions. By adopting this analogy we may postulate a general equation representing the kinetics of the flotation process: -dC/dt =K.CC ,Aa (1) The rate constant, K, will be a complex function involving reagent concentrations, particle and bubble sizes, induction times and no doubt flotation cell design. However, these are factors which can be kept constant in any series of experiments, permitting investigation of the exponents a and c, which determine the order of the reaction occurring in flotation. The various research investigations carried out so far have all aimed at evaluating a and c and in the majority of cases only since the concentration of air has usually been kept constant in a series of tests, so that a relationship of the following type has been investigated: -dC/dt = K1 Cc (2) The techniques of both batch testing and continuous testing have been used to investigate this relationship. The technique of continuous testing, in which steady-state conditions are established, permits direct investigation of the above equation. In the case of batch testing, C is decreasing continuously

Jan 1, 1961

By A. B. Cecala

Enclosed cabs have been used on surface mining equipment for many years to protect equipment operators from health and safety hazards. The surface mining and quarrying process is a highly mechanized process that generates large quantities of respirable dust. Due to economic factors, more older mining equipment is being used today than in years past. With this older equipment, it is common to observe deterioration of many components on the enclosed cabs which greatly reduce their protection effectiveness. NIOSH has performed a number of different field studies, as well as a comprehensive laboratory study evaluating various factors and parameters regarding enclosed cabs. NIOSH has recently completed a cooperative research effort with Sy-Klone International and Vulcan Materials Company to evaluate the effectiveness of a newly designed uni-directional filtration and pressurization system that brings all the clean filtered air in at the roof of the cab and extracts all recirculated air near the floor. This design provides the highest air quality to the equipment operator. Testing on this new system showed an almost 10-fold reduction in respirable dust inside the enclosed cab. The uni-directional design is easy to incorporate and should be considered for all new and retrofit systems in surface mining equipment.

Jan 1, 2009

Jan 1, 1963

By M. W. Franklin, D. W. Hendriks

"Changing ore types, feed grades and c1rculat1ng loads are some of the many factors that can make flotation feed-back control difficult. To control a flotation circuit using conventional fixed-parameter control algorithms, one must either tune the controllers very often or tune the controllers to the middle of the normal operating range. The former approach is very time consuming, while the latter approach can lead to long periods of either very sluggish responses or highly reactive responses which can lead to instability. The problem becomes compounded if feed-forward variables are introduced, creating even more variables to tune. An alternative to a fixed-parameter control algorithm is an adaptive control algorithm. An adaptive control algorithm continuously retunes itself based on previous reactions to its changes. Feed-forward control also becomes much more viable because the algorithm will tune the feed-forward parameters and the feed-back parameters simultaneously. Using the combination of feed-forward and feed-back tuning is an effective way to decouple the loops needed in flotation circuits where one circuit feeds into another. The advantages of adaptive controllers over conventional controllers will be introduced through the use of a simulator. Also discussed will the be the implementation of adaptive controllers at Brunswick Mining and some of the modifications that are available to help solve more difficult control problems.Brunswick Mining is located just outside of Bathurst, New Brunswick. The concentrator processes approximately 10250 tonnes per day of ore that assays at approximately 8.9 %zn, 3.6 %Pb, 0.3 r.cu and I 00 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 34 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb."

Jan 1, 1986

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By G S. Lane, G D. Richmond, J Dioses

This paper discusses the methods used in the design of flotation plants, including benchscale batch and locked cycle tests and pilot plant trials. Two case studies are presented, one for the Cadia Hill Gold Mine and the other for the Hellyer copper, zinc and lead plant. These case studies present different problems with widely different target grind sizes, liberation characteristics and HellyerÆs sequential flotation circuit versus CadiaÆs æsimpleÆ copper/gold flotation circuit. They have a common theme in that pyrite forms the principal floatable concentrate diluent. Hellyer ore contains finely disseminated chalcopyrite, sphalerite, galena, and tetrahedrite. The flotation plant design was based on extensive benchscale testwork (including locked cycle tests) on drill core and many months of operation of a 30 tonne per hour æpilot plantÆ, using the old Cleveland Tin Mine process plant suitably modified for the duty. The Cadia concentrator was designed on an extensive benchscale variability testwork program, approximately a dozen locked cycle tests conducted on drill core and two weeks of continuous pilot plant trials on three separate samples obtained from an adit into the orebody. The orebody is a monzonite porphyry with disseminated chalcopyrite/bornite/pyrite of very low grade (0.17 per cent Cu, 0.73 g/t Au). Methods used to establish the appropriate flotation circuits for the treatment of the Hellyer and Cadia ores, as well as the interpretation of the testwork data, are discussed in this paper. Plant performance is reviewed in the context of predicted versus operational performance.

Jan 1, 2002

By George D. Raitt

Anyone who has spent any time in and around the drilling and blasting profession knows that probably the most critical part is the drilling portion. A blasthole is nothing more than a cylindrical vehicle designed and strategically situated to hold and contain an explosive charge so that it can be detonated in the most efficient and optimum manner possible. It matters very little if the latest “State-of-the-Art” explosive or detonation system Is employed if the hole is poorly placed; i.e. excessive burden and spacing, sized incorrectly for desired results, insufficient in depth etc.. This is not to mention that the drilling phase is the most expensive, requiring sizeable initial outlays and upkeep. It’s also true that improper drilling can cause costs to skyrocket throughout the remainder of the work cycles such as excavating and hauling, crushing, screening and so on.

Jan 1, 1990

By A. C. Neiva

An energy-dispersive x-ray fluorescence spectrometer was assembled with the aim of analysing alloys and corrosion products of artistic, ethnological and archaeological pieces. The spectrometer is semiportable and consists basically of an 60kV/1.5mA X-ray tube with W anode and a Si-drift X-ray detector with Peltier cooling, with no need of liquid nitrogen. It was used for the analysis of the alloys and occasional corrosion products of several metallic pre-Hispanic pieces of the Museum of Ethnology and Archaeology of the University of São Paulo. Special care was taken to account for the contribution of spurious radiation from both the Pb primary collimator and the Zr detector collimator. The main components of most alloys were Au, Ag and Cu, but Pb, Ca, Fe and other elements were also identified. The characterization of the alloys and corrosion products is important for the subsequent conservation of the collection.

Jan 1, 2006

Komatsu America International has introduced two new hydraulic excavators. They can work in congested and confined areas. The tight tail swing radius of the PC128US-2 and PC22-8USLC-2 enables the excavators to minimize the work space. The units can operate in confined work settings that are inaccessible or counterproductive to traditional machines. Even the door is designed for tight working conditions. A convex door slides open along the exterior curve of the cab, rather than swinging out on hinges past tracks. And the excavators’ tight tail swing design allows them to load within the track width of the machine.

Jan 1, 2000

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962

By Grainne A. Matthews

Jan 1, 2009

By K Gordon, A Black

Two remediation strategies have been considered to reduce the levels of acidity and dissolved metals in acid mine drainage discharging from Sullivan Mine, West Coast, New Zealand. The oxidising strategy involves adding alkalinity and dissolved oxygen (DO) resulting in the precipitation of metallic oxides and decreased acidity. The reducing strategy involves removing DO, resulting in the precipitation of metallic sulfides, followed by addition of alkalinity to decrease acidity. Field remediation trials indicate a reducing system may be more effective for this site than an oxidising system. A residence time of only two hours in the limestone layer of a successive alkalinity producing system (SAPS) is sufficient to reduce acidity by 100 per cent, iron by 71 per cent, aluminium by 59 per cent, nickel by 38 per cent and manganese by 26 per cent. The proposed remediation plan will likely include a series of SAPS, followed by an anoxic limestone drain, and settling ponds to capture any remaining precipitates.

Jan 1, 2003