Search Documents

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By E. R. Cole

Laboratory heats of an 80 percent copper high-leaded tin-bronze alloy, similar to Brass and Bronze Ingot Institute (BBII) alloy 3A, were made with reduced tin content to determine whether an alloy comparable to BBII alloy 3A could be produced using less tin to aid in conserving this strategic metal. The tin content was lowered from 10 percent to 8 percent and 5 percent (nominal values), respectively, and the reduction in tin was offset by either increasing the lead content or adding zinc. Mechanical properties, machinability, and corrosion characteristics of the resultant alloys were investigated, and the mechanical properties were compared with BBII typical values and American Society for Testing Materials (ASTM) minimums for high-leaded tin-bronze alloy. Results indicate that the tin content of this alloy could be reduced approximately 1 percent (difference between the 8.4 percent actual tin composition obtained and the 9.3 percent BBII minimum) without seriously affecting the desired properties. Results also show the tin content could be reduced without significantly increasing the chances of rejects for mechanical property failures, which might result from normal variations in the casting process.

Jan 1, 1972

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

The estimation of the spatial variation of the b-value of the Gutenberg- Richter relationship is important for both the general interpretation of the mechanism of rock mass response and seismic hazard assessment. The interpretation of b-value as a parameter of rock mass response is discussed in this paper. The methods applied to evaluate the spatial variation of b-value and the algorithm for obtaining the magnitude of completeness and b-value for subsets of data are presented with some verification analyses. The algorithms presented enable the automation of a spatial evaluation of b-value.

Jan 1, 2014

By Virgil A. Marple

The objective of this contract was to conduct characterization, evaluation and/or calibration studies of instrumentation used for measuring the quantity of respirable dust in mining atmospheres. Initially, this work involved the upgrading and detailed evaluation of the aerosol test chamber and the development of impactors with respirable classification characteristics. These were used as standards in the chamber for measuring the quantity of respirable dust based on either the ACGIH or BMRC respirable dust criteria. A program was then conducted to calibrate several photometers. In addition, the mass sensitivity of the GCA RAM-1 photometer to water droplets in the respirable size range was determined. Three additional studies were also made in this program. First, an experimental study was performed to ascertain the effect of crosswind, cyclone orientation and particle size on particle sampling and penetration through the 10 mm Dorr-Oliver cyclone. Second, a theoretical study was conducted to refine the theory used to predict the particle collection characteristics of impactors. Third, filter samples with known quantities of diesel and coal particles were produced and delivered to the B. of Mines for testing a Raman scattering analysis technique to discriminate diesel particles in the presence of coal dust.

Jan 1, 1984

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001

By R. J. Gunderman

A conventional trailing cable connection box on a continuous mining machine was modified by the addition of two innovative devices. These are a pressure vent to preclude buildup of high pressure due to an explosion in-side the enclosure, and a grommet-type cable entry to simplify and speedup cable entering procedures. The innovative devices were evaluated for eight and one-half months in a working section of an underground coal mine. Laboratory tests before and after the in-mine exposure show no measurable change in the devices. Following the favorable in-mine evaluation, technical performance criteria were defined to serve as the basis of approval for the use of the innovative devices. Additional tests to measure comparable gripping of the cable by asbestos rope, substitution rope materials and by the urethane grommet-type entry were included in this effort. Also, literature for the last 80 years was searched. Comments are provided as to how the innovative devices comply with 30 CFR Part 18.

Jan 1, 1982

By S. P. Mishra, G. R. Chaudhury

The adsorption of Cu2+ ions by Penicillium sp. displayed a dual rate, with an initial faster phase followed by a slower one. The adsorption rate increased with increasing pH due to chemical and biochemical reactions. The Cu-loading capacity of the biomass increased at higher initial Cu2+ concentrations. Above 40 degrees C the adsorption rate decreased which may be due to partial hydrolysis of biopolymers which are essential constituents of the cell wall. Adsorption kinetics followed the Freundlich isotherm and the equilibrium concentration that was calculated on the basis of the isotherm matched the observed value well. A series of theoretical adsorption curves were produced using mathematical correlations between the mass transfer coefficient, the Cu2+ ion concentration at equilibrium and at time t. The correlation between the theoretical and observed adsorption rates for different experimental conditions was good. It was concluded that the results from the study were best explained using a mass-transfer adsorption model

Aug 1, 1995

By Kristineq Pankow

The August 2007 Crandall Canyon mine disaster raised national awareness of mining-induced seismicity (MIS) in Utah as well as general interest in how seismic monitoring might improve mine safety in the region. Unlike the situation in most other mining areas in the U.S., local seismographs in Utah?s Wasatch Plateau (WP) and Book Cliffs (BC) coal fields are an integral part of a modern real-time earthquake information system developed by the University of Utah Seismograph Stations (UUSS) as part of an Advanced National Seismic System. The UUSS earthquake catalog contains a continuous record of MIS at all active mine sites in the WP-BC region since 1978 (more than 18,000 seismic events = M 4.2). We describe characteristics of MIS and current seismic monitoring capabilities in the WP-BC region. We then demonstrate, using MIS from an example Utah coal mine, the ability to refine event locations with estimated absolute errors of ~200 m or less using a combination of (1) a double-difference relocation methodology and (2) ground truth information provided by mine operators. This approach enables sufficient spatial resolution to correlate MIS with mining activities, providing a useful tool to help improve mine safety.

Jan 1, 2008

The following pages discuss the objectives, the background, and scope of work of an industrial engineering analysis of far-,n haulage systems in underground retreat coal mining. This study ran concurrently with an existing industrial engineering study of methods of improving safety and production efficiency in underground pillar extraction. 1. OBJECTIVES The objective of this project was to provide basic data inputs that will inpart knowledge as to the major constraint to pillar extraction sections. Furthermore, the industrial engineering study will suggest ways to optimize haulage systems and to develop more efficient work practices and operational techniques that will maximize equipment utilization.

Jan 1, 1975

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. But wait a minute: Isn&apos;t head loss a negative number, a debit? And isn&apos;t fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves - pressure losses as negative values and energy additions as positive values-and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Feb 24, 1997

By Nuno Cruz, Saúl Rodríguez

"When executing offshore bored piles there are several specific factors and problems to consider in order to guarantee excavation stability. One of the methods employed to carry out this type of work consists in setting up a floating work platform, typically a barge, and implementing a soil stabilization system that combines a partial steel guiding casing with third generation polymeric drilling fluids. The main aspects to take into consideration when performing offshore pile boring works are soil stabilization, project design, work methodology and operational aspects. An example of a work methodology problem arises before any pile boring work takes place as the steel guiding casing contains water, sometimes salt water. What to do with this water in order to replace it by an adequate polymer fluid will determine the stabilization capacity as soon as the shaft advances below the protection of the casing. Another example of operational problem may derive from barge movements while executing boring activities. This study is the result of extensive field data collection and concrete logging analysis from marine projects using polymers in different continents. The bored pile stability target was set ranging between 2% to 15% of concrete overbreak. Values above 15% or below 2% mean that there is a stability problem. Then the off-target pile’s data is collected, analyzed and classified under categories. Thus, a direct correlation is established between the problem category and the final results. Modifying steps in the pre-established construction methods or operational variables guarantees target results without the need to replace the approved construction methods. As a general conclusion, the worldwide experience in large diameter marine works, allows to provide truthful information and solutions for these problems. In knowing how to follow a logical sequence of work and applying adequate work methodology will be the key for success.GENERALBackgroundTo carry out the drilling process of offshore bored piles there are two main options to take into consideration: drilling the pile by using full guiding casing until final depth; or using a combined system of partial steel guiding casing and support drilling fluids.The knowledge and situations described in this paper come from the experience acquired in different projects where the second method was employed. This construction method consists in installing a steel guiding casing by vibration and thus covering the water table and further stabilizing the soil below it with polymeric fluids until reaching the pile’s final depth. The Fig. 1 schematic shows an example of this method where H corresponds to the length of the steel guiding casing whereas the remainder of the shaft’s length is stabilized by polymer fluid. The entire bored length is full of slurry up to top of casing.In most cases this kind of civil works results from the need to build a bridge or executing port structures in places where the creation of temporary artificial peninsulas with fill material is impracticable or not allowed. Hence the need to use floating work platforms, commonly referred to as barges."

Jan 1, 2017

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

By Robert M. Matyas, P. E. Sperry, Robert J. Smith, A. A. Mathews

INTRODUCTION The first Dispute Review Board (DRB) was utilized on a tunnel project 20 years ago. Increasingly utilized on a wide range of construction projects, DRB&apos;s are becoming the norm on tunnel and underground projects. This paper summarizes the growth in this usage, uses observations and experience to establish that barriers to the utilization of DRB&apos;s are more perceived than real and that many arguments against the DRB concept are not valid, and notes some of the salient elements that should be considered in practice to optimize DRB effectiveness. The purpose of the paper is to provide an annotated checklist for current and prospective users. The basic concept, structure, and operation of DRB&apos;s are described elsewhere and will not be repeated here (ASCE, 1991). DISPUTE REVIEW BOARD USAGE A compilation of Dispute Review Board usage for tunnel and underground projects to January 1994 indicated use on 63 contracts with a cumulative construction value of $3.8 billion and a total of 60 disputes settled. As of that same date, DRB&apos;s were planned for another 63 contracts with an estimated construction value of $4.7 billion. (A listing of these 126 projects is available from the authors.) This success and popularity have spread to other civil projects as well as process and building construction. The increase in DRB usage has been exponential. See Figure 1.

Jan 1, 1995

Site specific geotechnical data, deposit characteristics and method of mining are key factors when assessing an appropriate slope design philosophy. Mining geotechnics should be viewed as an iterative design process linked closely with mine planning, development and operational safety constraints. This case study presents geotechnical investigations for slope design at Macraes Flat Gold Mine using kinematic, probabilistic and economic analyses tempered with knowledge of site specific conditions. The recommended designs not only reduce early waste stripping tonnages but also provide data to optimise final walls.

Jan 1, 1992

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973

"INTRODUCTION Industrial utilization of the present submarginal domestic manganese resources of the United States is wholely dependent at this time on the electrolytic manganese process established as the result of 4 years of continuous operation of the Bureau of Mines pilot plant at Boulder City and 7 years' operations of the Electro Manganese Corporation commercial plant at Knoxville, Tenn.Three Kids ore provided the feed for the Boulder City pilot plant during 3 years of operation. Hence, the electrowinning characteristics of the ore have been thoroughly established, making possible accurate estimates for commercial operations.Before the Defense Plant Corporation constructed the leaching plant, the Bureau of Mines conducted an exploration project to determine the extent and grade of the ore reserves. Additional exploration, development, and mining by the Manganese Ore Cc, have accurately determined the tonnage and grade of ore. A large tonnage of stock piled ore is now available for immediate processing, and a considerable tonnage of openpit ore has been stripped of overburden preparatory to mining. Numerous facilities, such as power, water, and housing, needed for an electrolytic manganese plant are already available.All of these factors, as well as plans for installation of scale electrolytic manganese plant facilities, are presented in detail in the chapter entitled, ""Mining and. Electrolytic Reduction of use from Three Kids Manganese Mine."" The Manganese Ore Co. kindly provided information on the present ore reserves and state of development of the mine."

Jun 1, 1945

By Joram M. Amir, Ernst Niederleithinger, Nikolaus Schneider

"Abstract: Diaphragm walls are used to provide a stable and watertight confinement for the construction of tunnels, underground railway stations, deep basements and other structures requiring deep excavations. Water seepage and soil loss through the joints have occurred on several occasions, causing extensive damage. This may have been due to uncontrolled concrete flow between the joints, unexpected geologic conditions or just poor workmanship.Different ways of quality assurance are applied on construction sites. Most of them rely on recording parameters of the construction equipment and conventional concrete quality control. In the frame of the EUREKA/ZIM project DiWaQ we have looked at several ways to perform non-destructive quality control. Some methods are to be applied after excavation before concreting (phase 1); others after the wall is completed (phase 2).For phase 1 we have used two different principles for checking the shape of the excavation, especially the joint to existing panels. A mechanical device which can be adapted to the excavating equipment was developed; field tested and validated on test and construction sites. It is described in detail in another paper in the same volume. A sonar-based device with a 10 mm resolution has shown good performance in the lab, but is still under development.For phase 2 different temperature sensors have been lowered into access holes to monitor the hydration heat developed during concrete curing. The same tubes can also be used to perform electromagnetic and ultrasonic crosshole measurements across or along joints to detect flaws. Especially the ultrasonic method has shown promising results on validation specimen at the BAM test site at Horstwalde, but limitations as well. Success substantially depended on the joint type, flaw size and distance of the sensors to the joint."

Jan 1, 2014

By Edmund S. Leaver, Charles E. Van Barneveld

In response to numerous requests from metallurgists and operators for information regarding the status of the sulphur dioxide leaching process , developed at the Southwest experiment station of the U. S. Bureau of Mines , Tucson , Ariz . , the following statement has been prepared . A more complete report is now in course of publication and will appear as Technical Paper 312. This process was devised to provide a cheap and efficient method for treating the so- called "porphyry " copper ores of the Southwest which generally contain both " sulphide " and "nonsulphide " copper minerals , mixed in such proportions that they can only be satisfactorily treated by a method which will concurrently recover both the sulphide copper and the nonsulphide copper . The latter term has been adopted to include all the minerals commonly referred to in operating phraseology in the mills of the Southwest as " oxidized" , " oxide " , or " soluble " copper . confident that the sulphide dioxide leaching process , as developed by us with the cooperation of the Miami Copper Co. and the Arizona Copper Co. , is suitable and commercially available for a wide range of ores .

May 1, 1922

By Richard H. Bares

The general or macroclimate of the study sites in western North Dakota is characterized by rapid and sometimes extreme daily and day-to-day temperature fluctuations, rainfall patterns which are erratic in spatial and temporal distribution and intensity, generally low relative humidity, plentiful sunshine, nearly continuous air movement, and a relatively short frost-free period. Of particular relevance to plant growth and productivity is the mosaic of microclimates: these microclimates are affected by landform (convex and concave surfaces); exposure; slope angle, length and aspect; soil color, texture and surface cover (litter), and vegetation cover. The most critical plant growth governing factor in this region is available water. It is determined principally by water input (precipitation) and water loss (evapotranspiration) which is increased by high temperatures, wind, and poor litter and vegetation cover. While spring and fall precipitation is generally gentle and soil-soaking summer rains frequently come in the form of intensive, soil-washing, localized convective thunderstorms of short duration. Due to the convective nature of these storms, summer rainfall is particularly affected by regional topography; southwest slopes and crests often receive more rainfall since these storms usually move in a northeasterly direction. The water loss due to runoff and consequent soil erosion arc major problems resulting from such "cloudbursts". Previous fall precipitation (September - October) when added to current seasonal precipitation (March - August) was found to be significantly correlated (r-.93) with plant production. Winter precipitation (snowfall) is relatively light as the prevailing weather is dominated by dry polar air masses from the north. The nearly continuous wind is responsible for removing snow from open exposures and depositing it in depressions and windbreaks. Although the winter precipitation is not a large component of the total annual precipitation, conservation of that which does occur would contribute to plant production during the following growing season. Generally clear skies over the region facilitate receipt of abundant sunshine at the earth&apos;s surface. While good for early season soil warming and plant photosynthesis, this abundant sunshine coupled with long days and nearly continuous wind is responsible for evapotranspiration exceeding precipitation by an average of six inches between June&apos; and September. On a local (micro) scale, the water deficit is most severe on the southern exposures which receive the most direct (most effective) solar radiation and therefore are warmer than other exposures. On a broader scale, it was found that ambient temperature extremes were slightly but significantly greater in the town of Beulah in the Knife River Valley than at the upland test sites, This may have been due to the difference in topography and/or the "urban heat island" effect. It is known that air temperatures in large cities may be 2° to 4°C higher than that of the surrounding countryside. It is also well known that basins, depressions or valleys are sinks for cold air masses and are often subject to frosts not occurring on adjacent upland sites.

Jan 1, 1982