Search Documents

By H. H. Fields

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot-deep vertical borehole¬. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmos¬phere, the total gas and water flows and the in situ pressure dropped, respec¬tively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the correspond¬ing values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By R. Pallini

The Franklin Research Center (FRO, a Division of The Franklin Institute was contracted by the U.S. Department of Energy to investigate the application of elastomeric materials for the purpose of smoothing loads on dragline thrust rollers. This report covers the design, fabrication, and demonstration of a portable- device for measuring roller circle track deviations and roller loadings. The results of this work are documented in this report. During December 1981, a field test group visited the Falkirk Mine, Underwood, North Dakota for the purpose of demonstrating the use of the designed and built device. The data collected indicates the practicality and usefulness of such a device for determining actual dragline roller circle roller loads, while the dragline is in service. The device was useful in determining roller load peaking that may be a contributing Factor in the premature failure of these thrust rollers. The device could be used for field evaluation of elastomeric cushioning materials used to eliminate these load peaks.

Jan 1, 1982

By Pedro Condori

Usualmente, la minera Atacocha está expuesta a grandes precipitaciones pluviales durante una larga temporada húmeda. Por lo que es necesario eliminar gran parte del agua colectada por las lluvias a través de las plantas de tratamiento de aguas de exceso que garanticen los contenidos metálicos por debajo de los limites máximos permisibles. En ese sentido, el presente texto describe la aplicación de un modelo matemático para comprender, manejar y optimizar las diferentes variables que afectan al proceso del tratamiento. El modelo está basado en los fenómenos de transporte de solución a través de la pila y la cinética de cianuración de los metales contenidos en el mineral, el cual permitirá simular los cambios en los parámetros operacionales y metalúrgicos como diferentes tipos de mineral, flujos entre plantas Merrill Crowe y CIC, un mejor tratamiento de excesos de agua para minimizar su efecto en la producción de oro y el manejo óptimo de soluciones y predicciones a futuro de producción de oro.

Sep 9, 2007

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel-economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By Se-joon Kim, Jong-hwa Chun

"‘Gas hydrate’ is the common term for a solid material formed from the combination of various gases as ‘guest’ and water as ‘host’. A series of large-scale scientific drilling and coring programmes conducted since 2000 revealed that natural gas hydrate exists in a wide variety of accumulations in the sediments. The scaled-up onshore and offshore field production tests during the last decade show that gas production technology will be realized to make gas production from gas hydrates viable in the future, recognizing its potentials as one of the future sustainable energy resources.The total produced gas was approximately 470 m3 by the hot water circulation method over 6 days of operation in the permafrost-associated Mallik 2002 project in the Mackenzie Delta of Canada. In the Mallik 2007-2008 project, the gas was successfully produced stably by the depressurization method for 6 days, up to 13,000 m3 cumulatively. The depressurization method applied in the Mallik test was shown to be an effective way to produce gas from gas hydrates. The Alaska field trial to inject mixed gas of CO2 and N2 to exchange CH4 in 2012 was successfully done for the first time to produce maximum 1,270 m3 per day. A remarkable achievement was made by Japan when it completed its first offshore production test in the Eastern Nankai Trough, producing approximately 120,000 m3 of methane by the depressurization method over 6 days in March 2013. The technical challenges and scientific uncertainties obtained from Nankai Trough production test provide Korea with more considerations as to the aspects of well completion, reservoir formation and seafloor stability, sand control, flow assurance, environmental monitoring, and etc., due to the different geological setting and geomechanical properties of the Ulleung Basin in Korea."

Sep 1, 2014

By Wingham D. W

Based upon the previous work of Norman & Loeb, a method was used to assess the comparative wearing properties of ten different alloys being used, or being considered for use, as mill liners and grinding media at Mount Isa, The materials to be tested were obtained in the form of large diameter balls, and were run, along with the regular ball charge, in a large ball mill operating under normal grinding conditions. At selected intervals, the test balls were removed from the mill, weighed and identified, and their relative wear rates determined.INTRODUCTIONInformation in metallurgical journals, from local iron and steel foundries, and from various metal promotional organizations has suggested that the various alloy compositions available should be examined and assessed for possible use as milllfners and grinding media.Previous attempts at evaluation of recommended materials for these applications elsewhere, have usually involved the purchase of large quantities of grinding balls or complete mill liner sets, requiring running periods of up to two years or more. As well as being both a costly and lengthy procedure, the information obtained may be of little significance, due to changes in milling practice, and ore characteristics during the period of operation.To overcome these difficuities, a method was adopted based on the short time wear rate test recommended by Norman & Loeb (1949) and Norman (1957) in which all the materialsunder consideration are ·subjected·concurrently to the conditions of service.Previous calculations of wear rates have been dependent1. Senior Metallurgist (Materials), Mount Isa Mines Limited.2. Metallographer, Mount Isa Mines Limited.Manuscript received at The Institute, 22nd April, 1963, and presented to the1963 Annual Conference.

Jan 1, 1963

By Verónica Rueda

El proceso de explotación de la Minera Rayrock se inició hace seis años a tajo abierto y ahora comprende las etapas de extracción del mineral, chancado, aglomeración, lixiviación, extracción por solventes y electro-obtención. En ese sentido, el presente trabajo describe el avance del proceso de extracción en el proyecto minero Ivan, perteneciente al yacimiento de la minera Rayrock a través de las técnicas de lixiviación de minerales oxidados y sulfurados de cobre y del manejo innovador en las operaciones de extracción por solventes y electro-obtención.

Sep 13, 2001

By Charles Sabine

The U.S. Bureau of Mines studied mines and prospects in the Bristol/Granite Mountains Wilderness Study Area (WSA) in 1982. The 45,000 acre WSA, located in the eastern Mojave Desert of California, is underlain by Mesozoic plutonic rocks with scattered roof pendants of Paleozoic (?) metasedimentary rocks. Two mines and six prospects are identified; one mine, the Silver Lode Mine, and a prospect of unknown name are adjacent to the area. The Silver Lode Mine has occurrences of silver, lead and zinc. Within the study area, the Comanche Mine has occurrences of iron and copper and the Iron Victory Prospect has an occurrence of iron. None are large enough to constitute a resource. Occurrences of magnesian marble at the Comanche Mine, Iron Victory Prospect, and elsewhere in the area contain too much MgO for commercial use other than agricultural soil supplements or crushed stone. Transportation costs to markets would exceed the value of the rock. At the Comanche Mine, situated in a roof pendant of marble, about 10 tons remain of a 110-ton pod of magnetite which contained 42.5% iron, and less than 50 tons remain of a mineralized fault breccia which averaged 2.5% copper and 0.3 oz/ton silver. Magnesian marble contained 41 to 45% CaO and 14 to 16% MgO. Primary and secondary silver, lead, zinc, and copper minerals are disseminated along altered joints and in quartz veins in quartz monzonite at the Silver Lode Mine, adjacent to the WSA. Analytical data are sporadic; samples contained as much as 0.12 oz/ton gold, 1.8 oz/ton Silver, 1.1% lead, 3.8% zinc, and 0.3% copper. Mineralized zones in the workings are not resources, but they might indicate possible silver-lead-zinc resources at depth. At the Iron Victory Prospect, lenses of magnetite and hematite with some chalcopyrite occur in a skarn lone in a marble roof pendant. About 110,000 tons of iron-rich rock, averaging 47.2% iron, are present; the largest lens contains about 30,000 tons. About 150,000 tons of magnesian marble, averaging 41.0% CaO and 11.7% MgO, are also present. Deposits of stone, and sand and gravel in the WSA are too distant from markets to be resources. Occurrences of energy minerals were not identified.

Jan 1, 1984

By Phillip M. Dight

A number of impending and actual pit wall failures have been observed and documented which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

The objective of this handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. There are several portions of the handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-1) List of Most Frequently Encountered Contaminants (Page 2-2) List of Candidate Contaminants and their Sampling Conditions (Table 2, Starting on page 2-5) Interpretation of Results (Page 2-16) Procedure for a, Health and Safety Inspection (Page 2-25) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, the Glossary of Terms, and the List of Commercial Products Encountered in Surveys.

Jan 1, 1975

Alluvial mining even of shallow deposits is often economically a marginal proposition and causes significant disruption of the land surface through the need for large scale excavation. In-situ leaching using chlorine-based solutions eliminates the need for excavation, the disruption of surface activities, and may greatly reduce processing costs and improve recovery especially of fine gold. A spreadsheet model has been developed to design and analyse the economics of in-situ leaching of alluvial deposits. In-situ leaching of shallow deposits may be achieved in a number of ways including solution infiltration via perimeter ditches or the use of injection and production wells. In most instances deeper alluvials may only be processed using well systems. Two deposits are analysed in this paper. The first consists of one metre of payable wash beneath one metre of overburden. Some thirty fields per year are treated processing 450 000 BCM per year at a cut-off grade of around $4/tonne ($8/rn3 or the gold value equivalent of 0.26 gh or 0.52 g/m3). The principal costs are well drilling and labour. Sensitivity analysis indicates that doubling the throughput halves the cost. The economics of the project are relatively insensitive to reagent costs and consumptions, and halving the recovery doubles the cut-off grade. Shallow deposits treated using the infiltration ditch system may be marginally cheaper and more conveniently managed although this depends on the relative cost of digging the perimeter ditches. In a second example, deep leads with one metre of wash beneath 30 metres of overburden necessitate significant drilling and feature reduced throughputs as a consequence. In the example chosen 30 fields a year are processed for an annual throughput of 65 000 tonnes costed at around $20/tonne (1.4 g/t Au equivalent, $40 /m3). Sensitivity analysis indicates that throughput, and drilling cost per metre are not important but there is a high sensitivity to recovery and to the depth to payable wash.

Jan 1, 1992

By M. Cornelius

Drilled shaft construction through caving soils has historically been an uncertain, risky and costly operation. Uncertain, because the zone of caving may or may not be known, risky because the loss of a shaft is disastrous, and costly because the Contractor, who faces these risks, must include large sums of money in his bid for shaft wall stabilization techniques. This case study will discuss the stabilization techniques that are typically used within the United States, and then present new technologies, born in Europe, that are being utilized in the States by Malcolm Drilling Company today.

Jan 1, 1999

By G. L. Neumann

Owing to the need for additional sources of supply of both zinc and lead following World War II, the Bureau of Mines investigated many abandoned lead-zinc mines in the eastern United States. A series of shallow veins in south-western St. Lawrence County has long been a subject of speculation. These veins, which average about 4 feet in width and cut across the bedding of the country rock at right angles, are filled with calcite-carrying galena and sphalerite. The deposits have been worked sporadically during the last 115 years. From 1837 to 1852 the Coal Hill, the North, and the Victoria mines near the village of Rossie were at their peak of activity. Other calcite veins were prospected and a small production was realized. The Bureau of Mines began diamond drilling May 1, 1950, under the general supervision of McHenry Mosier, chief, Mining Branch, Bureau of Mines, Region VIII, and under the immediate supervision of the author) who was project engineer, following the preliminary examination by Robert S. Sanford. A total of 3,870.2 feet was drilled in 18 holes on four of the numerous deposits scattered over Macomb and Rossie townships. Drilling was completed September 21, 1950.

Jan 1, 1952

By Wm. W. Adell

"These hydrocarbons belonging to the same chemical series as methane, having the general formula CnH2n have many chemical properties in common with methane and their addition to a lean gas charges the properties and burning characteristics of the gas in the same general direction although to a different extent. The hydrocarbons of this series do not readily enter into chemical reaction with other substances and therefore are incapable of combining with oxygen or polymerizing in the disturbing system and thus cannot cause gum and room troubles commonly met with in the distribution of manufactured gas.As the number of carbon atoms in the molecule increases, i.e. in proceeding from methane throughout the series, the oxygen requirements for the complete combustion of unit volume of the gases also increases; in other words, the calorific values of these hydrocarbons (as gases) increases from methane. Similarly the specific gravity increases from methane in the same order. In Table 1 are shown some of the physical constants and properties of a few of these hydrocarbons which hive bearing on their use for enriching gas."

Nov 1, 1927

By C. T. Baroch

The purpose of this report is to describe the design features and techniques used in operating a plant capable of producing about 1,500 pounds of titanium metal per day. The process used was based on the reduction of titanium tetrachloride with magnesium, a modification of what is generally known and spoken of as the Kroll process. Sponge metal crushed to melter's specifications was the end product of the operation as conducted. The report is divided into sections covering general plant layout and the major unit operations. These, in turn, are each divided into discussions of the equipment, operating procedures, and typical results. Descriptions are given in more detail than is generally expected of a technical report. During 1953 and 1954 over 130 engineers and businessmen, officially representing some 80 industrial, chemical, end engineering firms, visited the operating plant, and their questions, which indicated a serious interest in details, have served as a guide for the material contained in this report.

Jan 1, 1955

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By Richard D. Short

The Pseudo Static Pile Load Test, PLT, is a rapid method for determining pile capacity. Pile design is usually based on theoretical calculations of ultimate load capacity using soil data from a field investigation. The pile capacity is confirmed during construction by analysis of blow counts using dynamic formulae, dynamic pile monitoring, and load testing. Load testing is the most direct and reliable method of determining the actual capacity of a pile. Conventional load testing procedures, however, are time consuming and expensive. A typical load test requires installation of two to four reaction piles, construction of a high-capacity steel test frame, hydraulic jacks, and dial gauges, and will typically take one to three days per pile. Costs for load tests range from $10,000 to $20,000 per test. The Pile Load Test machine features a 25-tonne weight mounted on a mobile test frame. PLT load tests can be performed in a matter of minutes once the equipment has been mobilized to the site. This paper examines three test sites where the PLT test method was used and compares the results to conventional load test results and theoretical capacity calculations.

Jan 1, 2000

By Jack F. Harang, P. B. Leavenworth

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By P. B. Leavenworth, Jack F. Harang

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By A. Trusiak

"Increasing energy costs in mineral processing is making it necessary for tighter controls over various parts of the concentrating process. Continuous monitoring and control of critical process streams can be easily performed by today's many computer systems. Indeed, the list of successful applications of computers to grinding and flotation control continues to grow. The day is rapidly approaching when the use of computers within concentrators for either process control or simply metallurgical accounting will no longer be a luxury, but a necessity. The benefits from such applications far out weight the initial investment.This paper describes the current application of a process control system at Brunswick Mining in north-eastern New Brunswick. Emphasis is placed on the control of a CuPb flotation circuit, and the benefits derived-from this control.No. 12 Cu-Pb Flotation: The complex nature of the Brunswick flotation process has been described else-where. 1,2,3 Four final concentrates are eventually produced, these being a Zn concentrate assaying 53% Zn, a 30% Pb concentrate, a 20% Cu concentrate, and a bulk Pb Zn concentrate assaying 35% Zn and 17% Pb. The Cu concentate, Pb concentrate, and bulk Pb Zn concentrate are all derived from a primary CuPb concentrate assaying 26% Pb, 11% Zn and 1.8% Cu.The No. 12 CuPb circuit produces approximately two thirds of the total primary CuPb concentrate. No. 12 ore, assaying 3.5% Pb, 9% Zn, 0.25% Cu and 100 g/tne silver, is ground in two parallel grinding circuits. Each line uses a 3.2 x 4.2 meter rod mill in closed circuit with two parallel 3.2 x 3.9 meter ball mills. Ball mill and rod mill discharges are classified in two stages of cycloning. The secondary cyclone overflow, or flotation feed, is controlled at 65% passing 37 microns."

Jan 1, 1981