Search Documents

By Brijes Mishra

This paper presents a correlation of acoustic emission (A.E.) with physical and mechanical properties of different types of rock and coal specimens which were tested under aegis of a consultancy project from a Columbian Mining Company. In this study, three types of rocks which are sandstone (Arneisca), siltstone (Arciolita) and claystone (Limolita) and two different types of coal were tested. The tests were carried out under constant loading rates according to ASTM Standards for determining Young?s Modulus and Poisson?s Ratio. In both cases a MTS electro-hydraulic loading system was used. Mode of failure in each material was characterized by the acoustic emission and the results were substantiated by the deformation characteristics of the materials during failure.

Jan 1, 2006

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

By Jorge Agramonte Bermejo

Dado que el Perú es un pais rico en carbón antracítico y con limitados yacimientos de carbones semicoquizables, la tecnología que predominará para una producción mayoritaria será en relación con el consumo de la antracita en la industria de acero y de otras que le signifiquen ahorro de divisas y petróleo. En ese sentido, el objetivo del texto radica en hacer conocer la potencialidad de los yacimientos, cantidad, calidad de recursos y reservas de los mismos.

Nov 8, 1982

By Wilton Johnson

The Bureau of Mines study indicates that land utilized by the mining industry for mineral extraction and processing from 1930 through 1980 amounted to 5.7 million acres, or 0.25 percent of the land mass in the United States. Land reclaimed by the industry during the same period was 2.7 million acres, or 47 percent of the land utilized. Land use by the mining industry includes surface land used for excavation or mining, for waste from underground mining, and for wastes from milling or processing operations. Data on land use for disposal of overburden waste from surface coal mines and on areas affected by subsidence associated with underground mining are included for the period 1930-71 only. The 10 leading States in total land used for mining over the 51-year period were, in decreasing order, Pennsylvania, Kentucky, Ohio, Illinois, West Virginia, Florida, Indiana, California, Alabama, and Missouri. Seven mineral commodities accounting for 92 percent of land use are, in decreasing order, bituminous coal, sand and gravel, stone, phosphate rock, clay, copper, and iron ore, all predominately surface mined. Bituminous coal production was responsible for nearly half of the total area utilized. Reclamation of mined lands and waste disposal sites over the reporting period was largely on lands utilized in mining bituminous coal; 75 percent of the land used for bituminous coal production was reclaimed.

Jan 1, 1981

This paper deals with the application of table flotation to two unusual mineral dressing problems. Both problems involved the removal of interfering minerals at sizes too coarse to normal froth flotation.The first problem was the removal of arsenical minerals from Broken Hill gravity concentrates without further size reduction. Table flotation without grinding of the original concentrates gave almost complete rejection of the arsenic from the concentrates. A typical test result was a reduction of arsenic in jig concentrate from 0.75% arsenic to 0.007% arsenic.The second problem was to develop a method to produce a high grade calcium carbonate concentrate from coastal dune sands containing about 10% silica and about 80% calcium carbonate. The sands were about 30 mesh British Standard Screen (B.S.S.), and for economic and other reasons it was stipulated that the separation be made without grinding. Again, table flotation gave excellent results. A concentrate was produced containing 99.62% acid soluble material, representing a recovery of 98.69% of the calcium carbonate in the feed with a rejection of 96.44% of the silica.The investigations' were carried out at the Kalgoorlie Metallurgical Laboratory, under the Department of Mines...

Jan 1, 1954

Jan 1, 1947

Jan 1, 1947

By PW Meisel

An hydraulic-powered reel system to minimize peak tension transients in shuttle car trailing cables has been theoretically designed and analyzed using a computer. A single spring-loaded take-up sheave stores or gives up cable to maintain tension within specified limits. Controls have been incorporated to shut down the vehicle before all cable is removed from the reel and to de-energize the cable in the event of a reel/cable jam. Full-scale hardware configuration drawings sufficient for manufacture of a test system have been completed.

Jan 1, 1983

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By C. H. Johnson

The Big Jim mine of the United Eastern Mining Co. is at Oatman, Mohave County, Ariz. Oatman is in the foothills on the western side of the Black Mountains, at an elevation of about 3,000 feet. It is on a paved highway about 30 miles west of Kingman, the principal distributing; center for mining supplies in the district, and 25 miles from Topock, en the Colorado River. Both latter towns are stations on the Santa Fe Railroad; Oatman has no roil connection. Mining conditions are typical of western Arizona; water is scarce, no mine timber is available locally, and the winters arc mild and the summers hot. The supply of a killed labor is usually adequate, but in 1933-34 it w not more than sufficient for the restricted operations. Wages have been $4.00 to $4.50 for miners. Electric power was supplied from Kingman and cost about 2.6 cents per kilowatt-hour.

Jan 1, 1935

MINExpo International is billed as the largest exposition for the mining and mineral processing industry. And the 2012 edition, scheduled for Sept. 24-26 in Las Vegas, NV, is no exception. Put on by the National Mining Association (NMA), attendance at this year?s show is expected to be significantly more than the 38,500 who attended the last MINExpo in 2008. The exhibit will also be quite a bit larger in 2012 than it was at the previous MINExpo. More than 1,800 companies, representing more than 30 countries, will fill the Las Vegas Convention Center. The more than 850,000 sq ft of exhibit space will include the North and Central halls as well as South Halls Nos. 3 and 4. And the Silver Lot outside of the front door, under construction in 2008, will be filled with more exhibitors. The 2008 show attracted about 1,220 exhibitors occupying more than 600,000 sq ft of exhibit space.

Jan 1, 2012

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. loader. These instructions are based upon two actual install .at ions: one made in a mine on loader, model 14BU10-11AH, and one in the factory on model 14BU10- 11AH. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other loaders with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other loaders and can determine any necessary modifications if they are not.

Jan 1, 1973

By Júlia Mont’Alverne Martins

A Votorantim Metais processa pós de aciaria elétrica (PAE) e outros resíduos contendo zinco em sua unidade de Juiz de Fora, por meio do processo Waelz. Devido ao alto teor de óxido de cálcio (CaO) nos resíduos processados, a etapa de desalogenação apresenta baixo rendimento de remoção de fluoretos -aproximadamente 20%. O processo de lixiviação sob pressão foi testado para o tratamento de amostras de óxido Waelz (O.W.) da Votorantim Metais com o objetivo de lixiviar os cloretos e fluoretos contidos nesse material. Os parâmetros avaliados foram: temperatura de lixiviação (120°C a 180°C) e razão de carbonato de sódio (Na2CO3) adicionado (100kg/t a 200kg/t óxido Waelz), em um reator piloto com capacidade de 10L. A técnica mostrou-se eficiente para lixiviação de cloretos, com remoção acima de 94,2%. Os resultados para fluoretos obtidos apresentaram variação entre 63,0% e 96,2% de rendimento de lixiviação e uma forte correlação dos resultados com a temperatura. Esse processo mostrou-se eficiente em escala de bancada, apresentando rendimento de extração superior a 90% para a remoção de halogênios em temperaturas acima de 150°C e adição de Na2CO3 de 140 kg/t O.W.

Aug 17, 2017

Greater mining productivity requires a more efficient cutting process. The cutting force available from today?s mining machines has been optimized with respect to machine size and weight. Researchers have shown that when employing water-jet-assisted cutting, bit forces and drum torques can be reduced significantly, which may allow mining machines to become lighter and more efficient. The Bureau of Mines has initiated a program to develop a water- jet-assisted rotary cutting system using the conventional bit assisted by a directed water jet operating at moderate pressures (3,000 to 10,000 psi). This water-jet-assisted cutting system has the potential to improve cutting efficiency without increasing machine horsepower or water usage (beyond what is presently used for dust control) or requiring fundamental changes in mining practice. IR addition to improvements in productivity, other anticipated benefits of water-jet cutting include reduced generation of respirable dust, elimination of frictional ignitions, increased bit life, reduced fines, and fewer machine vibrations. The papers presented at this open industry meeting discuss the development of water-jet-assisted cutting technology and future application of this technology to a variety of mining techniques including roof drilling and longwall mining.

Jan 1, 1985

By Thomas M. Gurtowski

The New Pacific Northwest Baseball Park, now known as Safeco Field, is located directly south of the Kingdome in Seattle, Washington, and will be the new home of the Seattle Mariners baseball team. The location of the ball field is shown on Figure 1, Vicinity Map. The seating capacity is 45,600, and outfield distances are 331 feet in left, 405 feet in center, and 326 feet in right field. The overall dimensions of the stadium are 680 by 800 feet. It is bordered on the east by the Burlington Northern Santa Fe Railroad main line. A unique aspect of this ballpark is the retractable roof with a north-south span length of 660 feet. The roof consists of three separate sections that roll on elevated rails running east-west on the north and south sides of the stadium. The soil conditions consisted of near-surface fill underlain with alluvial and Estuarine deposits to depths of 60 to 80 feet. The bearing soils consisted of very dense, glacially overridden deposits. Groundwater is 4 to 7 feet below the ground surface, and the alluvial deposits are subject to liquefaction during a strong motion earthquake.

Jan 1, 1998

By R. W. Watson, H. D. Peer

"This paper outlines the history of steel linings in the Autogenous Mills, the factors influencing the decision to convert to rubber lining, and the operating and cost experience with the rubber liners to date. INTRODUCTIONSherman Mine is an open pit iron ore mining, concentrating and pelletizing operation located at Temagami, Ontario. The operation employs 392 hourly employees and 81 salaried employees and has an annual capacity of over one million L.T. of high quality iron ore pellets produced from low-grade magnetite ore.The Sherman Mine is a joint venture; 90% owned by Dominion Foundries and Steel Limited (Dofasco) of Hamilton, Ontario, and 10% owned by the Tetapaga Mining Company, a wholly-owned subsidiary of the Cleveland Cliffs Iron Company of Cleveland, Ohio. The operation and management of the mine is by Cliffs of Canada, Limited. Development of the property was started in 1965, with pellet plant production beginning on March 17, 1968. At the present time, the orebodies contain sufficient reserves to sustain operations at current production levels for 30 years. Mining was originally carried out in three orebodies, the North, South, and West pits. The North Pit has been exhausted and mining operations ceased in the spring of 1980. A fourth pit, the East Pit, will be developed during the early 1980's."

Jan 1, 1981

By Marcel Vallée

Frequently, costs overruns and defaults in mining project performance result in serious problems and headaches for all project participants and impact on corporate objectives, profits and image and, occasionally, lead to project failure. As mining professional s, we should be very concerned that, in a recent World Bank paper (Weber-Fahr, 2001), geological and technical risks were considered the most important ones facing mining projects. Whenever we manage to reduce or minimize these risks, we are in better position to overcome the environment-, market-, finance- and community-related ones. The causes of this situation seem rather systemic, as a fairly long list of industry problems with new pro jects has been described in industry papers in pas t and recent years. A brief review of industry problems with mining projects will be given first, followed by a review of the basics of the current Quality Management and Continuous Improvement perspectives that have evolved from earlier quality control and quality assurance systems and policies. Particular particular attention will be given to the work of W. E. Deming. As the system approach is an essential part of such policies, it will be described succinctly. Given that poor communications and interactions among geologists, mineral processors and mining engineers/operators ca n seriously affect project efficiency and profitability, these interrelated processes with in the mining systems will be analyzed and modelled and the impacts of such situations will be described through a number of anonymous case histories and examples. A synthesis of Dr Deming's management system, includ ing his Four teen P oints and System of Profound Knowledge, will be prese nted .

May 1, 2002

Recently discovered Carboniferous bentonites are variable in charadeI and thickness, but being altered aeolian, ash-fall tuffs, they are probably extensive. Most are the Ca-montmorillonite type without the natural swelling characteristics of the Wyoming deposits, but their situation, thickness, and response to beneficiation through cation exchange may give them some potential as sources of future economic deposits.INTRODUCTIONLoughnan and See (1959) gave an account of bentonites and fuller's earth deposits of New South Wales. The most likely potential industrial sources were those occurring in the uppermost formations of the Newcastle and Singleton Coal Measures (Permian) in the Hunter Valley and deposited during epochs not marked by strong contemporary vulcanicity.One feature of the record of known occurrences at that time was the absence of bentonites from the thick volcanic sequences of the Carboniferous, but since this paper appeared, many bentonite beds have been discovered by the writer in the Carboniferous facies formerly known as the "Kuttung Series".The purpose of this contribution is to report briefly on the occurrence, genesis, mineralogy, and economic potential of these deposits which augment possible sources of bentonite near major industrial centres on the eastern seaboard.The potential world demand for bentonite would increase markedly with the trend to pelletization in the steel industry, if its use in this field became more general. More detailed mineralogical studies will be presented in later publications.STRATIGRAPHIC DISTRIBUTIONBentonite occurs at irregular intervals throughout a thick sequence of dominantly continental, plant bearing strata...

Jan 1, 1965