Search Documents

By Edmond Chin

The area encompassed by the political entities included in this study com-prises 11 million square miles or about 15 percent of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest is-land or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The region is noted for its great rivers. The Chang, Huang, Amur, and Mekong are respectively the fifth, sixth, eighth, and eleventh longest rivers in the world. The Ganges-Brahmaputra has created the world's largest delta, which covers 30,000 square miles. Abutting East Asia are the Sea of Japan, Dong Hai, Nan Hai, Bay of Ben-gal, and Arabian Sea. In the Southern Hemisphere, there is the Indian Ocean and the South Pacific Ocean. The Continental Shelf adjacent to the region constitutes a large proportion of the world's readily accessible shelf area. On the other hand, the Philippine and Java trenches and, further out, the Mariana Trench reach to formidable, abyssal depths, downward to 6,000 fathoms. Contrasting to this is Mount Everest, which reaches a lofty height of 29,028 feet. And then there is Xizang, whose high plateaus have been called the roof of the world.

Jan 1, 1992

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

ON mineral lease 38 of the Sulphide Corporation Limited, Broken Hill, a shaft was sunk in the early days Ior prospecting purposes and at the present time it is accessible as far as the 1000-ft. level where a connexion exists with the main workings of the Corporation's Central Mine, mineral lease 9. About the year 1895· a crosscut was driven east from this shaft at the 1330-ft. level cutting the Central Ore-body in mineral lease 9 and the shaft is supposed to extend a further depth of 25 ft; but no records of any of this work are in existence, the whole of the evidence being based on hearsay and memory:Fig. 1 shows the position of the Extended shaft in relation to the main workings. The shaft filled with water to the 1000-ft. level where it overflowed through the crosscut to the main shaft and was pumped to the surface, but when the South drive on the 1300-ft. level was pushed to the southern boundary, it was deemed advisable for safety, to tap the water at this level and so relieve the...

Jan 1, 1919

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By K. Awuah-Offei

Energy efficiency has become significant due to cost and environmental considerations. Comminution and material handling have been identified as the two most energy intensive processes in mining. The objective of this work was to evaluate truck-shovel energy efficiency strategies using discrete event modeling. Energy audits and time and motion studies were conducted at a surface coal mine to acquire data. A discrete event simulation model of truck-shovel operations was built in Arena® and validated with the field data. The model was used to evaluate the effect of using a larger shovel, and optimizing truck-shovel matching on fuel efficiency. The results indicate that using a larger excavator increases the fuel efficiency of the operation while optimizing truck-shovel matching does not. However, using a larger shovel will lead to under-utilization of the shovel. This work shows the potential benefits of using discrete event simulation to model energy efficiency of mining operations.

Jan 1, 2012

By R. C. D. Phillis

The management of critical resource inventories is an important productivity lever and a significant risk factor?risk in the sense that poor resource availability lends itself to disempowerment of workers, unsafe work practices, wasted spending (high unit costs),and poor quality of work (including mining waste/rework). Most underground platinum mines experience lost blasts that directly lead to reduced productivity. In most surveyed shafts, 30% of lost blasts can be attributed to shortages of critical material and/or equipment. The problem is prevalent despite the existence of conventional transitory surface and underground stores. This paper discusses the introduction of buffer stores as a complementary materials storage system in order to improve health and safety in mines as well as reduce lost blasts. Both quantitative and qualitative results have shown that buffer stores result in dramatic improvements in productivity and are readily acceptable by stakeholders. Keywords Buffer stores, lost blast.

Jan 1, 2011

By S. F. Diehl

Drill cores from uranium roll-front deposits, hosted in lower Cretaceous strata, were examined from the proposed Dewey Burdock in-situ uranium recovery site in the northern part of the Edgemont uranium district, South Dakota. Uraninite (UO2), coffinite U(SiO4)0.9(OH)0.4, and doloresite (H8V6O16) occur as pore-occluding cements within the Fall River Formation in the Dewey area. In contrast, within the Lakota Formation in the Burdock area, uranium (with very little vanadium) is absorbed onto woody fragments and amorphous carbonaceous material in pressure-solution seams. Both areas have typical uranium roll-front mineralogy with 0.5 wt. % pyrite in the reduced solid phase and no pyrite in the oxidized solid phase. The groundwater at the ore zone is not oxygenated, so the uranium is relatively insoluble. Uranium in solution in ground waters is <10µg/L at Dewey and <22 µg/L at Burdock. Micromineralogic and geochemical data are being used to understand water/rock interactions, uranium distribution and movement, and as input factors for predictive reactive transport models.

Feb 27, 2013

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

By Donald O. Capstick

The U.S. Bureau of Mines conducted an inventory of the prospects and mineral resources in the Scodies RARE II area (No. 5212) in 1982. No mineral production is recorded from the area, and no mines are being developed. The Scodies RARE II area is comprised primarily of light colored granodiorite with minor inclusions of mafic granitic rocks. Late stage differentiates of magmas resulted in quartz veins and pods. Metasedimentary rocks which have been mineralized in some parts of the Sierra Nevada were not observed within the study area during this investigation but small inclusions have been reported.

Jan 1, 1983

By J. A. Herbst

During the last decade it has been established that conventional flotation control strategies based on classical control theory result in significant increases in grade, recovery, and operating-cost savings. In the current report a description of an advanced model-based control philosophy is presented. The derivation and verification of a simplified flotation model is described. The implementation of a Kalman filter for estimation of unmeasured variables for input to controllers is discussed. Several control strategies using the model-based approach are described, emphasizing the nonlinear nature of the flotation plant. Expected trends in the implementation of such model-based flotation control strategies in the future are discussed.

Jan 1, 1986

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

By S Rupprech, T Lund, H Fourie, PH van Rooyen, NM Vegter

Rosh Pinah Zinc Corporation (Pty) Ltd (RPZC) operates an underground mine at Rosh Pinah in southern Namibia producing zinc and lead sulphide concentrates. It currently mines around 0.7 Mtpa run-of-mine ore containing around 6-10% zinc and 1.5-3.5% lead. As part of past exploration and current intensified exploration, a massive continuous low grade ore body was identified which grades at around 3% zinc equivalent. This ore body is near current mining infrastructure and could be amenable to bulk mining methods. In the present paper a concept is presented on how it could be exploited. As a precursor to exploitation of the low grade a number of enhancements are proposed for the current mining operations including: ? shortening load-and-haul distances by extending the conveyor raise further down the mine in a phased manner and back-filling of waste into mined-out stopes; ? use of mobile crushing plant at the crusher tip, and; ? installation of a system to allow scoops to load directly from stopes into ore passes close by combined with truck loops to haul from these ore passes to the crusher tip. To exploit the low grade ore body the following concepts are proposed: ? open stope mining from two areas at a total rate of up to 2 Mtpa; ? underground pre-beneficiation of mined low-grade ore near the stopes using either dense medium separation or X-ray sorting; ? pre-beneficiated tails back-filled to mined-out stopes and; ? pre-beneficiated product transported to surface by linking into proposed run-of-mine conveying system.

Jan 1, 2007

This paper on the relation of Granite and Sedimentary Contacts to Victorian Mining will, it is hoped, be of interest to members of the Institute.The broad fact that gold often occurs&apos; at or near the junction of granite with sedimentary silurian or metamorphic rocks has been noted by some Victorian geologists, miners, and prospectors; but the fuq practical value -of the fact does not seem to have been fully realised by prospectors. Glancing at the Geological&quot; Map of Victoria, one can see that many of our goldfields &apos;are situated at or near the junction of granite with Palceozoic sedimentary formations, and that some of our alluvial fields are on granite. Many prospectors are possessed of this knowledge but when prospecting a contact locality, they would be just as likely to confine their search for auriferous matrices to spots a quarter of a mile on the sedimentary side, as on the actual contact line of two formations.

By E. D. Wilson

A study of factors related to subsidence was specified in a project proposal entitled "Structural Analysis of Block-Caving Operation, San Manuel Copper Mine, Pinal County, Ariz.," approved by the Bureau of Mines early in 1953. This proposal was designed by Charles H. Johnson, then chief of the Base Metals Branch of the Minerals Division, Washington, D. C., assisted by Dr. Leonard Obert, chief of the Applied Physics Branch, Region VIII (now Region V), College Park, Md., and E. D. Gardner, chief mining engineer, Bureau of Mines, Washington, D. C. It read as follows: This project is a study of the mechanics of undercut block caving in a deep ore deposit. The San Manuel is a low-grade disseminated copper deposit containing nearly a half billion tons of ore lying at depths of 500 to 2,000 feet. Development is just starting. Production is to begin in 3 to 4 years (in 1956) at a rate of 30,000 tons of ore a day, or 60,000 tons of copper a year. A Government loan of $90,000,000 /subsequently increased to $94,000,000/ and a long-term Government purchase contract support the capital investment, which will total about $110,000,000.

Jan 1, 1957

By P. Wyhoit

En las últimas décadas, la industria minera sueca se ha caracterizado por una racionalización y mecanización crecientes. En ese sentido, el nivel de producción debe ser correlativo con el número de empleados. Por ello, el cambio del transporte con rieles a sin rieles progresaba rápidamente, ya que de esta forma iniciaba una nueva fase de automatización mecánica. Sin embargo, los ingresos de muchas minas pequeñas suecas disminuyeron durante la década del 60 debido a la caída de los precios del mineral y al aumento del costo de la mano de obra. En consecuencia, el presente texto describe el uso de la minería sin rieles desde 1971. Esto condujo a un rápido aumento de producción que compensaba el bajo precio del mineral. De esta manera, la operación sin rieles permitió la supervivencia de minas menores que enfrentaban, durante los últimos años, los decrecientes precios de minerales hierro-fosfóricos en Europa.

Nov 1, 1975

By H. G. Hammon

Uranium miners have been shown to develop lung cancer in direct proportion to the time of exposure in the mine and the concentration of radioactivity (cumulative working level).1 Radon gas is continually evolved from the uranium ore, but because of its shoe half-life, 3.82 days, it is soon decomposed into particulate daughter products, which along with the dust in the mine, become deposited in the miners&apos; lungs. At present, massive ventilation is the only effective method of reducing the radioactivity concentration in the mines. However, the Bureau of Mines is evaluating the possibility of using coatings on the mine wall that will have sufficiently low permeability to radon that the gas will decompose into the particulate daughter products before it can permeate the coating. Permanently trapped in the coating, the daughter products would be prevented from dispersing in the mine atmosphere. Lawrence Livermore Laboratory was asked to aid in this investigation. The direct determination of radon permeability is more difficult than that of the other noble gases because of the short half-life of the gas and radioactive contamination of the apparatus. We felt that it should be possible to estimate radon permeation coefficients from other noble gas permeation coefficients. It was noted that the log of the diffusion constants for helium, neon, argon, and krypton, as reported by Meares2,3 plotted to a straight line-against the square of-the gas molecularddia meter. The log of the permeation coefficients also plotted to a straight line against the square of the gas molecular diameter. Thus, by determining the permeation coefficients of such gases as argon and krypton through various films and coatings, it appeared likely that radon permeation coefficients could be estimated. In addition we felt it should be possible to find some relationship between polymer structure and he noble gas permeation coefficient that would aid in the selection of coatings materials as radon barriers.

Jan 1, 1975

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

By T. J. Driscoll

Methane-air mixtures can ignite as a result of sparking or rubbing of materials, particularly by impact involving light alloys and rusted steel where an exothermic thermite reaction can occur. This report reviews the published literature and describes a new method utilized by the Bureau of Mines for studying the processes occurring during collisions of light metals with rusted steels. The method involves measuring the spectra of sparks and explosions in methane-air mixtures using a photodiode array. Initial results obtained using magnesium and aluminum alloy 6061-T651 projectiles striking rusted steel are reported. These results indicate that the continuous parts of the spectra show a larger intensity for incendive sparks compared with nonincendive sparks, with the largest relative change in the higher energy, ultraviolet region. An unexpected shift of the intensity maximum for the continuous parts of the spectra towards the infrared region was observed for the more incendive sparks. Evaluation of rusted steel samples with electron microscopy, energy-dispersive X-ray spectrography, and Auger electron spectroscopy after they had been impacted by aluminum alloys indicated that aluminum was transferred to the steel in the form of islands that became larger as a function of increasing projectile velocity.

Jan 1, 1982

By Orlando C. Gaspar

The presence of ?ne-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sul?de ores. The bene?ciation of most massive sul?de ores from the Iberian Pyrite Belt requires extremely ?ne grinding to liberation sizes of K80= 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning pat-terns has shown that the different ore types are distributed as ore lenses within the massive sul?des. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the ef?ciency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types de?ned at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sul?de ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997

By Orlando C. Gaspar

Abstract - The presence of fine-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sulfide ores. The beneficiation of most massive sulfide ores from the Iberian Pyrite Belt requires extremely fine grinding to liberation sizes of K80 = 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning patterns has shown that the different ore types are distributed as ore lenses within the massive sulfides. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the efficiency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types defined at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sulfide ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997