Search Documents

By J. M. Stuve

In this Bureau of Mines investigation, the low-temperature heat capacities of polycrystalline phases corresponding to the sulfide compounds CoSO?89' CoS1?33, and CoS2 were measured by adiabatic calorimetry within the nominal temperature range 5 to 300 K. The derived absolute entropies S298 were 10.36±O.02, 12.96±O.03, and 16.31±O.03 cal?mol-1?K-l, respectively, assuming third-law behavior. In addition, the standard enthalpy of formation 8Hf298 of CoSO?89 was determined by bromine solution calorimetry. The derived value of 8Hf298 was -50.63±2.1 kcal?mol-1, based on the 8Hf298 of Co0. This result is considerably more negative than previously published formation values based on high-temperature gas equilibrium studies.

Jan 1, 1985

By Baruch Grinbaum, Edwin Bwalya, Robert Minango, Deogratias Bukunkwe

Solvent extraction of Cu from acidic leach, using an oxime extractant, e.g. LIX 984 or Acorga is a well known and established process. As the process advances, Cu is extracted to the solvent and is replaced by H+ in the aqueous phase. At high acidity the distribution coefficient of Cu between the solvent and the aqueous phase decreases, and eventually relatively high concentration of Cu remains in the raffinate, regardless of the number of equilibrium stages. In many processes this phenomenon is immaterial, as the raffinate returns to the leaching and no copper is lost. But when the copper raffinate is used for processing of additional metals, minimal concentration of Cu in the raffinate is essential for an effective process. The recommended process includes three steps: 1. SX-1: Standard extraction of Cu with oxime. The resulting raffinate contains about 6-8 g/L Cu and 50 g/L H2SO4. 2. SX-N: Extraction of most of the acid into an amine-based solvent, and stripping it with a base, e.g. aqueous ammonia, caustic, Na2CO3 etc. The extraction removes no metals, but decreases the concentration of acid from 50 to 10 g/L. 3. SX-2: Extraction of the neutralized solution once more with oxime, to remove the residual copper. Such a process enables one to get down to 100-150 ppm Cu in the final raffinate. This process was developed and tested in the R&D facility in Chambishi Metals plc, by a joint team of Chambishi & Bateman, using Cognis LIX 984N and real solutions from the plant. In the laboratory scale, the equilibrium isotherms for SX-1, SX-2 and the neutralization were developed. Computer simulation of the results showed that the optimal configuration is two stages for both extraction and stripping for SX-1. For SX-2 2-3 stages of extraction and two stages of stripping are needed. The stripping stages may be common to both SX-1 and SX-2. The neutralization of SX1 raffinate was tested both by conventional precipitation with lime and by extraction with Alamine based solvent extraction and stripping with a solution of 10% NaOH. For the SX-N only one stage was needed for both the extraction and stripping. The bench scale pilot plant was run for both SX-1 & SX-2. The results were very similar to the simulated ones, and the configuration of 2E2S for SX-1 and 3E=2S for SX-2 delivered the required raffinate with less than 150 ppm Cu.

Jan 1, 2005

By S. Fawell, H. R. Manouchehri

The main electrophysical properties, i.e., dielectric constant and electrical conductivity, of pure calcite, quartz and wollastonite mineral samples were measured and their triboelectric charge attributes were investigated by contacting minerals particles with different tribochargers made from different materials. In addition the energetic work function values for mineral samples were estimated due to their acquisition charge. Besides, the behaviour of triboelectrically charged of different particle size fractions of mineral samples were inferred. Finally an attempt were made to translate the findings from single mineral systems to a real carbonate ore. The results exposed good prospects to beneficate the examined minerals by triboelectric separation.

Jan 1, 2002

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By Joelma Krugel Brites

Com a perspectiva do uso de aços API em ambientes sour service, o controle de inclusões e precipitados é essencial para bom desempenho. A precipitação de carbonetos e nitretos de Nb e Ti, assim como a formação do MnS foram analisados criticamente em aços de alta resistência e baixa liga – HSLA- com Mn entre 0,3 e 1,6%, Nb 0,02-0,1%, S 0,001-0,005% e Ti 0-0,02% em peso. Os valores da temperatura de precipitação do MnS, Nb(C,N) e Ti(C,N) foram obtidos por meio do software ThermoCalc™. A partir desses resultados, possíveis tendências da precipitação foram discutidas e relacionadas com a temperatura de não-recristalização, traçando um comparativo entre temperaturas de processo e precipitação. Três aços produzidos com a composição estudada atenderam os requisitos mecânicos de tração da norma API 5L X65M.

Oct 30, 2017

By P. C. Good

The Bureau of Mines conducted a laboratory investigation of a sinter-leach method to recover aluminum and fluorine from waste carbon potlining residues from secondary cryolite recovery operations in aluminum reduction plants. After removal of carbon by burning, the residue was sintered at 900° to 1,100° C with silica and N2CO3, then crushed and leached with dilute NaOH solution, dilute Na2C03 solution, water, or water containing residual Na2O which remained in the sinter after reaction and decomposition of Na2CO3. Over 90 percent of the contained aluminum and up to 87 percent of the contained fluorine were extracted from this waste product in the form of a mixed alkaline solution. Treatment of the alkaline solution with CO2 yielded a white precipitate containing 89 percent of the original aluminum and 61 percent of the original fluorine as a mixture of synthetic cryolite and alumina, together with a variable excess of soda.

Jan 1, 1969

By Jeffrey C. Hillman

The need to recruit locally produced engineers by the South African Mining Industry led to the Engineering Faculty at the University of the Witwatersrand developing a number of academic bridging initiatives for educationally disadvantaged students. The graduation rate achieved during the initial five years of operation by the most successful of these programmes has been on a par with that of al other students but the performance of subsequent intakes has declined to such an extent that the continuance of this scheme could now be at risk. One reason for this reduction in throughput is that many of the applicants for the increasing number of mining bursaries have been more interested in the bursary than the profession and have either failed or dropped out due to a lack of application and motivation. This will have serious consequences for both Wits and the Industry if it continues and some method of identifying unsuitable or suspect applicants needs to be introduced as a mater of urgency. It is recommended that an introductory course be set up at a working mine that would be run under the auspices of Wits, as a joint venture with industry, and include a level of academic input that would provide both bridging needs and certain first year credits. The final form of this course will require extensive consultation with al parties but needs to be completed before the end of 1996. It is further recommended that the advertising and promotion of mining careers be expanded and much improved.

Jan 1, 1996

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005

By Lawrence Addicks

T HIS has been a most momentous year in the annals of the Institute. We have been in the midst of a situation which, were it not for the convulsions of social unrest with which life is surrounded on every side, would have attracted the attention of the world at large. I do not refer to the desperate campaign for new members. That has gone on much as usual except that, this being leap year, the annual proposal to the M. & M. Society has been omitted. Nor do I refer to the desperate situation which we found in other directions, the spread of Bolshevism, the burning of the Engineers' Club, the fact that the selling of copper appears to have become one of the lost arts. No, I speak of the great question which has to be. settled once and for all, as to whether this great Institute should adopt simplified spelling. The whole trouble started in the ranks of the California Hysterical Society. It appears, while most of the San Francisco members can read and write, several of them cannot spell. It also appears that the Secretary, in editing the Transactions, has perhaps made just a little bit too much of a point of employing the correct Stoughton idiom. At any rate, the rebels filed an amendment to the constitution, and the stage was set for civil war, with perhaps more stress on war than on civil.

Jan 1, 1920

By M. Hermanus

1. INTRODUCTION It gives me great pleasure to extend my warmest greetings to everyone attending the 30th International Conference of Safety in Mines Research Institutes. I would also like to bid a special welcome to all of the international delegates who have travelled to Johannesburg to take part in what surely be a most rewarding session of deliberations. As you come together over next four days, you will have a wonderful opportunity to exchange ideas and information on strategies and practices for the implementation of sustainable patterns of development. The objectives of this meeting are both timely and far-reaching, as countries around the globe work towards the sustainable use of the world resources. Each of you brings a high level of expertise to these deliberations. I know that you will make the most of this opportunity to address the challenges and opportunities to highlight the most innovative and technologically efficient methods of social protection in order to ensure an increase in the quality of life, health, safety and living environment for the peoples of the Africa. Our country, although endowed with an immense and diverse array of mineral deposits, is perhaps best known in the mining industry for the fact that it is the world’s biggest producer of gold. Although South African gold production has declined over the past years and the industry faces serious problems, it is a myth that the South African industry is moribund. There is a new energy coursing through the South African producers which will ensure their powerful presence for many years to come, based not only on their domestic production but also and probably increasingly on their external operations. Africa features prominently in the latter category.

Jan 1, 2003

By V. R. Degner

En las últimas décadas la declinación en los contenidos metálicos de los yacimientos mineros se ha constituido en un aporte para el desarrollo progresivo de máquinas de flotación de gran tamaño. En este sentido, las máquinas de flotación de las décadas del 50 y 60 fueron reemplazadas por máquinas de mayor capacidad, potencia y simplicidad en los controles del proceso, adquiriendo ventajas económicas y operativas que pueden ser aplicadas a los diseños de plantas de gran tonelaje en el futuro. Por ello, el objetivo del texto es revisar los procedimientos seguidos en el desarrollo sistemático de las celdas de 1000 pies3 de capacidad y la evaluación de su performance en el beneficio de minerales metálicos.

Oct 14, 1980

By N. C. Trivedi

Natural calcium carbonate, commonly known as limestone is an abundant resource pretty much worldwide. Calcium carbonate occurs naturally as the main constituent of chalk, limestone, and marble. One of the unique characteristics of this abundant mineral is its versatility. Major markets for calcium carbonate are: paper, plastics, caulks and sealants, carpet backing, paint, and food additives. This broad spectrum of consuming industries has warranted producers of this industrial mineral to be innovative and quality focused simply to meet the ever increasing demands for performance. This need for improving performance of calcium carbonate has led to the development of new sources of calcium carbonate, natural as well as synthetic.

Jan 1, 2002

By Alan M. Jessop

This paper discusses the distribution of frozen ground in the zone of discontinuous permafrost in relation to the pattern of surface temperature. The importance of understanding permafrost in relation to surface construction and open-pit mining operations is stressed.

Jan 1, 1972

By J. D. Davis

THIS report gives results of an investigation of the carbonizing properties of the following eastern Kentucky coals: Elkhorn No. I bed, No. 28 mine, Wayland, Floyd County; Elkhorn No. 2 bed, Turner No. 5 mine, Drift, Flood County; Leatherwood (Haddix No. 5) bed, Leatherwood mine, Leatherwood. Perry County; and Harlan bed, Path Fork mine, Path Fork, Harlan County. The carbonizing properties were determined by Bureau of Mines-American Gas Association (BM-AGA) tests at 800° and 900° C. and by expansion tests in the sole-heated oven. Plastic properties were determined by tests in the Gieseler and Davis plastometers. The coals were tested singly and as blends with 20- and 30-percent low-volatile Pocahontas No. 3 coal. The dry, mineral-matter-free, fixed-carbon content of the carbonizing samples ranged from 56.7 percent for Elkhorn No. 2 to 59.7 percent for Leatherwood, and the heating values on the moist, mineral-matter-free basis ranged from 14,420 B. t. u. per pound for Elkhorn No. 2 to 14,720 for Harlan. The percentage of ash ranged from 2.9 to 6.1. The fluidity of three coals, measurer. In the Gieseler plastometer, ranged from 230 to 670 dial divisions; the fluidity of Elkhorn No. 2 could not be determined by this method. Blending lowered the fluidity of each coal; the fluidity of the blends containing 20 and 30 percent Pocahontas No. 3 ranged from 16 to 53 and from 8 to 17 dial divisions, respectively. Agglutinating values determined on silicon carbide-coal mixtures in the ratio 15:1 ranged from 3.8 to 6.3.

Jan 1, 1952

By R. H. Schutz

This publication lists the respiratory protective devices approved by the Bureau of Mines as of December 31, 1968, and the names and addresses of their manufacturers. The purpose of this publication is to inform the public about approved equipment for safe use in mines and mineral and allied industries.

Jan 1, 1969

By Jorge Ganoza

Dado que la metalurgia no es una ciencia nueva -en tanto que los conceptos utiilizados como propiedades geológicas, mineralización, procedimientos de extracción y recuperación de oro son practicados durante mucho tiempo, la variación actual de su nombre, no es determinante. En ese sentido, el presente texto señala algunos aspectos metalúrgicos del oro como: mineralogía de los depósitos de oro, las muestras geometalúrgicas para el programa de pruebas, mezclas de minerales, ley de oro y relaves de cianuración.

May 1, 2013

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By Leslie F. Sawatsky

Each potential oil sands developer deals with the question of optional sources of raw water to supply large water demands that range from 50 to 80 million cubic metres per year for each of six existing and planned developments. The Athabasca River currently supplies nearly all of the water to the existing mines via conventional bank intakes, which has resulted in some concern over the effects of reduced river flows. This paper describes the various water supply options, and the likely scenario for future oil sands water supply projects. Various water supply options have been suggested including Athabasca River water via infiltration galleries, groundwater, combined Athabasca River water and alluvial groundwater using wells (i.e. bank filtration systems), diversion of tributary rivers, utilization of large lakes in the region and pumping from other large rivers in the region. Investigations show that the size of river catchment needed to support raw water usage by a typical oil sands mines exceeds 5,000 km2 eliminating all tributary rivers that are located in the oil sands region except those rivers with large drainage areas like Firebag and MacKay Rivers. Lakes cannot be used as a source of supply due to large water deficits for smaller lakes and the large cost of sourcing water from a lake as large as Lake Athabasca. A groundwater source alone would not likely meet the large water demands. River intakes on the Athabasca River will likely continue to be the most practical water supply option for oil sands mines north of Fort McMurray, although various types of Athabasca River intakes are possible. Existing intake systems include screened riverbank intakes, forebay intakes, and river bottom intakes. Infiltration galleries are not feasible for most sites, though some bank-filtration-type systems using high capacity wells may be an option if there is sufficient thickness of high-permeability alluvium at a suitable location in the Athabasca River valley.

May 1, 2004

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

By Detnet Solutions

1. “Daisy-Chain” concept The term “daisy-chain” stems from the fact that when the HotShot? detonators are connected there is a chain or electrical path for electrical current to flow from detonator A to detonator B, detonator B to detonator C etc until the path is terminated by an electrical means. The “daisy-chain” concept has long been used in electronic detonator systems, historically used in Expert Explosives’ ExEx 1000 5/6 wire system and currently in use in African Explosives Limited (AEL’s) Electrodet? electronic detonator system and has been adopted as the basis upon which the “auto-programmability” of the HotShot? electronic detonator system functions. HotShot? Detonators are connected to each other in a string, completing a “daisy chain”, and during the auto-detection mode of the control equipment, it is possible for the equipment to determine the order of hookup of the detonators as well as map the entire blast layout. The auxiliary components (Row Controllers & Branch Controllers) assist the control equipment in mapping the entire blast by indicating different points on the blast, i.e. The inflection point of a row of blast holes on a closed chevron timing pattern, the beginning of row of blast holes on open chevron timing pattern and extra blast holes or extra blast rows.

Jan 1, 2004