Search Documents

Ground falls (roof and rib) have historically been responsible for about 50% of all fatalities in bituminous underground coal mines. In some recent years, the number of ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, last year?s Crandall Canyon twin mine disasters, in which 9 miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990?s these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents in the past 5 years. Progress has also been made in pillar recovery. Safer mining technologies have reduced the number of fatal incidents, but some recent failures have underlined the need for careful management of the retreat mining process. On the other hand, more than 400 miners continue to be injured each year by rock falling from between supports, and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities. Available technologies such as roof screen, rib bolting, and inside control roof bolters could dramatically reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By G. L. Oldright

The Metallurgical Branch of the Bureau of Mines, as a part of its duties under the Organic Act, works to prevent wastes in industry and to disuse inmate information on the fundamentals of metallurgical processes. During the war, the necessity of large production was increasingly emphasized. Such duties necessitate from time to time the study of units of full commercial size, the operation of which is beyond the facilities of the Branch. When developments have reached this stage; work has been continued in cooperative agreements with operating companies that have been willing to contribute the use of their plants and staffs and to allow the publication of the results obtained for the common good of the industry.

Jan 1, 1948

By Zetti Gavelan, Eric Ruiz, Emilio Delgado, Ely Loayza, Jesus Cruces

La planta concentradora de minera Las Bambas logró rápidamente, y de manera sostenible, llegar a su capacidad de diseño de 140 Kton/día. Para mejorar el concepto de conminución, se inició el proceso de reducción de tamaño en el manejo de los factores de carga, diseño de mallas de perforación y diseño de voladura del macizo rocoso, debido a la variabilidad de la competitividad del yacimiento que está formado por skarn y pórfidos. Gracias a un trabajo en conjunto, la maximización del sistema de molienda SAG se consigue de manera sostenible con la integración del equipo de voladura en las optimizaciones realizadas en la planta, de manera que se logra incrementar la operación a 150 kton/día, lo que utiliza de manera eficiente la energía de la operación.

Sep 20, 2019

Jan 1, 1966

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall As used in the mills to replace losses from evaporation, seepage, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation- Which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects.

Jan 1, 1932

By T. P. Meloy

Traditionally the mineral and mining engineers have characterized particles by sieving and-settling. Within the last decade, with the advent of the scanning microscope, entirely new experimental and theoretical approachesl-10/have been taken to minutely define the particle surface. This approach depends upon a hypothesis which takes advantage of the recent developments in automatic micro-scopes which can acquire large amounts of information in a short time and the new computational techniques which rapidly reduce the information to meaningful, practical data. Historically sieving and settling are the oldest sizing techniques known. Sieving by square screens, shown on Figure l-A is a common, current practice for sizing particles both in the laboratory and in production. A woven cloth is used which usually has square openings. The size particle that will pass through the opening dependent on a complex relationship of its morphology. As can be seen in Figure l-A, neither the width nor the height of the particle is determined by sieving. From square screens one and only one parameter characterizing the particle size is obtained, that parameter is the radius of the sphere that will just pass through the given sieve opening. A variation of square mesh screen is the slot screens, shown in Figure 1-B. Here another measure more closely associated with the height of the particle is obtained. Once again, one and only one parameter is associated with the particles' shape.

Jan 1, 1977

By D. Duvris

Health and safety issues are a very important aspect of mining activities. Although the application of scientific research and current technology shields workers from many dangerous aspects of mining, accidents do happen. Many companies and institutions worldwide have committed to a continuous effort to minimize such occurrences. In this study, the health and safety data pertaining to the Greek mining and quarrying industry for the last 3 decades are presented and critically evaluated with respect to number of workers, annual production, etc. Appropriate indices are also calculated regarding the incidence and frequency of accidents. Health and safety issues specific to mining in Greek are also discussed.

Jan 1, 2000

By J. R. Campbell

THE need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. WASHABILITY STUDIES The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money, can hardly be spent on "feed surveys" to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus.

Jan 1, 1928

This paper discusses the prediction of subsidence over partial extraction systems in thick coal seams. A model based on empirical techniques using influence functions is developed to calculate the surface ground settlements above extraction panels. Independent of the influence function, two field parameters, the subsidence factor and the angle of draw (limit angle) are required to define the model. Both these parameters are best observed from critical or super critical subsidence areas. However in thick seams, extraction widths are typically sub critical and therefore it was necessary to refine an estimation process for sub critical conditions. Partial extraction systems in NZ are characterised by variability with respect to extraction thickness and depth. As extraction proceeds along a panel, conditions deteriorate once the critical span width is exceeded and therefore percentage extraction decreases. A further variable was introduced to the modelling which allows for varying extraction sequences. Two comparisons with field observations, one over a partial extraction panel, the other over abandoned workings, showed the method gave good agreement to measured subsidence values.

Jan 1, 2002

By Frank L. Hess

"New England" and "granite" if not synonymous are at least associated terms. Where there are granites that are not deeply eroded there are usually pegmatites, the most erratic of rocks, and of them New England has a full portion. Many of the New England pegmatites contain the rare alkalis - lithium, rubidium, and cesium. however, the same in homogeneity of the earth's crust that has made the New England pegmatites unusual, in that so many of them contain the rare alkalis, has likewise made the distribution of the rare-alkali minerals sporadic even in those pegmatites, and most contain only enough to furnish collectors with more or less ornamental and uncommon minerals. New England has long had numberless collectors of minerals, and the mineralogists of its various schools have published many papers on the pegmatitic minerals, including those of the rare alkalis, but none of the papers have dealt with estimates of quantities. In this paper we have tried to place the emphasis on quantity rather than on mineralogy.

Jan 1, 1943

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

By Charles T. Ford

In 1971, Bituminous Coal Research, Inc~ established a program to provide the coal industry with the necessary information and technical capability to investigate and evaluate potential problems concerning trace elements in coal and coal-related materials. The initial efforts at BCR in developing or adapting analytical procedures for the precise determination of trace elements in the parts per million to parts per billion range were detailed in a report titled "The Development of Analytical Methods for Determining Trace Elements in Coal and Coal-related Products." A subsequent reports contained descriptions of reliable analytical methods refined by BCR for determining mercury in coal and coal ash and also in coal mine water. his paper reports initial progress in applying recently-acquired trace-element analytical capabilities to solving potential coal industry problems. In this case, the effect of a coal-cleaning process on the distribution and removal of potentially harmful trace elements in coal was evaluated. Coal cleaning offers the possibility of controlling potentially harmful emissions resulting from combustion of large tonnages of coal by removing the pollutants prior to combustion.

Jan 1, 1977

By R Lastra, Y Choi, C Hamilton, P Kondos

Hydroseparation (http://www.cnt-mc.com) was used to concentrate sized fractions (from <38 ¦m to 150 ¦m) of various ore products ahead of carbon-in-pulp (CIP)-treatment. The resulting size-by-size concentrates were mounted as monolayer polished sections and subjected to automated unattended precious metal searches by image analysis (see Lastra, Wilson and Cabri, 1999). Systematic variations in Au-deportment permit quantification of Au reporting as discrete grains from fresh-feed through to pressure oxidation (POX)- and CIP-feed. Application of hydroseparation, image analysis and assays to characterising tailings (from <10 ¦m to 106 ¦m) from four mine sites is also described. Results are encouraging enough to predict that the combination of hydroseparation (HS) and automated image analysis could become a standard methodology for study of precious metal ores and metallurgical products.

Jan 1, 2008

By Amit Srivastava, Monica Malhotra

In a congested city or urban area, so called “lifeline of the city”, i.e. Gas, Electricity, telecommunication, as well as other utilities or facilities are supplied or transported underground through buried pipes or utility tunnel. Sometimes these buried pipes or utility tunnels are deep underground and interfere with the foundation of new structure. It is highly probable that a pile foundation is placed near an existing underground buried pipe or utilities tunnel and may influence its load bearing capacity. Hence, estimation of reduce load bearing capacity of the pile foundation placed near the existing buried conduit or utility tunnel is a complex soil-buried structure interaction problem. It is further complicated owing to uncertainty in estimation of geotechnical parameters of foundation soil due to measurement and testing errors, inherent soil variability and model transation. Under such circumstances, load bearing capacity is best assessed in probabilistic framework or through reliability analysis. The present study demonstrates how concept of response surface method (RSM) in conjunction with Numerical Analysis and First Order Second Moment (FOSM) methods can be combined to per the reliability analysis. The study answers the following question “reliability in reduction in the load bearing capacity of single pile placed near the existing underground pipe or utilities tunnel”. It is demonstrated that the approach provides first hand ination on the reduction in the load bearing capacity and then estimate the reliability of that estimation in terms of an index called Reliability Index (). Such preliminary investigation can be useful for advocating the detailed analysis as well as in the decision making for relocation of pile foundation.

Sep 1, 2022

By J. C. Fox, V. L. Ketellapper

The Summitville Mine, located in the mountains of Southwest Colorado, is an abandoned gold mine. From 1984 to 1992, Summitville was mined for gold using an open pit heap leaching technology. During this period, the volume of acid mine drainage released from the mine significantly increased. This was attributed to the development of the mine pits, the waste rock piles, the heap leach pad, and increased discharges from the drainage adit. The release of this acid mine drainage resulted in the destruction of the aquatic ecosystem for more than twenty miles downstream of the mine. Beginning in 1993, plans were implemented to reduce the amount of acid mine drainage released from the mine. The majority of this work has been completed at the mine. This work includes removal of the Cropsy Waste Pile, closure of the Heap Leach Pad, and revegetation of disturbed areas. Significant improvements to water quality downstream of the mine have occurred resulting from mine reclamation. Aquatic life has returned to portions of the previously mining impacted areas. This study discusses the actions taken to reduce the amount of acid mine drainage generated at the Summitville Mine, the costs of these actions and the resulting reduction in metal loadings. Over 250 samples taken at over 10 locations since 1993 form the basis of this evaluation. Copper loading is analyzed as an indicator of the effectiveness of the actions taken.

Jan 1, 2002

The Production Profile Program is written for use on a Digital Model PDP 11/70 computer using a Fortran IV level G language. It may be run on any system which uses G level or an upward compatible version of Fortran IV language. Please note, however, that the Model PDP 11/70 for which the program was written is programed to read DEC026 type keypunching. If the user's computer is programed for another type of keypunching it may be necessary to re-keypunch the Production Profile Program. The Production Profile Program uses a fourteen card input. The data must be keypunched according to the layout described in detail in the multiple card layout forms (following). The output from this program must be printed on wide paper, as a full 120 columns are used. The samples of output at the back of this appendix have been reduced for inclusion in this report.

Jan 1, 1977

By Marcos Meyer Machado

A determinação de características microestruturais como base de controle de qualidade tem demonstrado cada vez mais a sua importância nos processos de aglomeração de minério de ferro. A linha de pesquisa do presente trabalho envolveu o desenvolvimento de técnicas de embutimento de pelotas seccionadas em resina condutora, de desbaste e polimento da superfície das amostras e emprego do microscópio eletrônico de varredura em conjunto com a técnica de Electron Backscattering Difraction. Por meio das técnicas empregadas de microscopia baseadas em parâmetros cristalográficos específicos, foram obtidas ilustrações forescatter e mapas de fases minerais ferríticas, silicatos e óxido de ferro que caracterizam a microestrutura de pelotas tratadas termicamente em forno piloto. O desenvolvimento desta metodologia promove subsídios para estabelecer futuramente uma relação das estruturas observadas em escala microscópica com as propriedades reconhecidas e mapeadas no produto final.

Aug 17, 2017

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

By G. H. Gronhovd

This report describes the design and initial operation of a slagging gasification pilot plant installed by the Bureau of Mines at the Lignite Research Laboratory, Grand Forks, N. Dak., in 1958-59. The tests covered in this report were conducted over a period of about 2 years, beginning in April 1959. The pilot plant was designed for eventual operation at pressures ranging from 400 to 600 p.s.i.g. (pounds per square inch gage); however, for the preliminary test reported here, the gasifier was fitted with a low-pressure slagging section and operated at atmospheric pressure and at 80 p.s.i.g. The reason for using a low-pressure slagging section for initial operation was to facilitate modifications in design during the development of a reliable slagging procedure.

Jan 1, 1962

By Lester A. Blackner

Discussion of the paper of LESTER A. BLACKNER, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 102, June, 1915, pp. 1249 to 1290. SIDNEY J. JENNINGS, New York, N. Y.-In the historical part of the development of the caving system discussed by Mr. Blackner, I notice the absence of one man's name, Charles Henroten. Mr. Henroten used the caving system in South Africa in the. Kimberly mines, and realized from his work there that ground would cave when properly prepared. I think it is due him that his name should be mentioned in connection with an exposition of this system in America.

Jan 12, 1915