Search Documents

By J D. Pease, J M. I Tuppurainen, P D. Munro

This paper examines how legislation and regulation can be external drivers of technical change in mineral processing and extractive metallurgy and how the industry can respond. Two examples are considered; the production of copper metal from concentrates and the cyanide process for gold production.The Clean Air Act (1970) in the USA initiated a wave of attempted innovations in the extractive metallurgy of processing copper sulfide concentrates to meet forthcoming standards on sulfur dioxide emissions. Interestingly, a satisfactory technical solution existed (flash smelting and gas capture) but had not been widely adopted.Nearly fifty years later the primary copper industry finds itself with new challenges. One major challenge is how to deal with the increasing level of arsenic in copper concentrates. Most countries impose an upper limit on arsenic in imported concentrate; typically, 0.5% As or less. Higher arsenic concentrates can be blended with cleaner ones to meet the limit, but this tactic cannot be used indefinitely as the average arsenic level of global concentrates rises inexorably. Further, smelters (often in urban locations) cannot be expected to deal with both ever-increasing arsenic in the feed and stricter restrictions on emissions and disposal. A rising “inventory” of primary copper deposits are already constrained from development by high arsenic concentrate. These deposits will need to be developed if future copper demand is to be met. An economic and technical solution to arsenic is needed. The gold industry may also face challenges in the use of cyanide, by far the dominant lixiviant used in gold and silver production. Public perception has driven restrictions on the use or transport of cyanide in some jurisdictions. History suggests that such pressure is only likely to increase. While there are several alternative lixiviants, none can yet match the utility and economics of cyanide.Such important issues will not be resolved by incremental change or new equipment items. They require development of new process technology - a tectonic event rather than an incremental change. It requires sustained effort (and expenditure) over decades and is very unlikely to result from “business as usual” for producers, suppliers or academics. Past major process developments were driven by a dire need for economic survival or by legislative change. What will drive the future changes?CITATION:Munro, P D, Pease, J D and Tuppurainen, J M I, 2017. Technology change by regulation – a cresting wave?, in Proceedings MetPlant 2017, pp 45–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Paul E. Bennett, James S. Browning, Thomas L. McVay

Continuous 1.0- to 1.5 - ton - per - hour pilot plant flotation tests were made to determine the technical and economic feasibility of recovering beryl from flotation tailing being produced at the spodumene concentrator of the Foote Mineral Company , Kings Mountain , N.C. Best results were obtained when using an acid circuit and amine - type cationic reagents to float a bulk beryl - feldspar concentrate and then selectively floating the beryl away from the feldspar , using a petroleum sulfonate collector . About 77 percent of the beryllium in the pilot plant feed was recovered in a concentrate containing 6.42 percent BeO . The capital cost of an integrated flotation plant capable of treating 500 dry tons of spodumene mill tailing per day for recovery of beryl and feldspar is estimated at $ 210,000 . Indicated direct operating costs for the plant were $ 1.52 per ton of dry spodumene flotation tailing treated . This approximated the value of beryl recovered , but potential profits of about the same magnitude lie in concurrent recovery of marketable spodumene and feldspar byproducts .

Jan 1, 1964

By Long Han, A. V. Kalinin, Xiujian Luo, Xiaobo Wang, Xiaoou Xia

"Inertia vibration crusher is a kind of vibration equipment which crushes ore by vibration. When the inertia vibration crusher works, ore between the two moving jaws is subjected to the high frequency contact force, which is produced by the two moving jaws with high frequency synchronous reciprocating motion. The synchronous motion of the two moving jaws depends on the self-synchronous feature of the inertia vibration crusher. To study the self-synchronous feature of the equipment, the dynamic model was established, in which relative parameters were taken into consideration. The kinematic coupling relations of the assemblies are discussed, and appropriate calculation method is chosen to solve the vibrating differential equation. Whether the two vibration exciter can realize synchronous operation depends on the ability of the vibration system's capture moment. Results show that though the two rotors’ motors and damping coefficients are different, and two jaws’ damping and stiffness coefficients are also different, as angular velocities of the two unbalanced rotors reach a certain value, the vibrating system can be stable. Their angular velocities tend to be equal, and the swings of the two moving jaws can be the same. The horizontal vibration and swing of the frame are large in a few seconds after starting the machine. When the system runs stably, the horizontal vibration and swing vanish, and the vertical vibration is stable. The study and its results can provide reference for the optimization design and parameter setting of inertia vibration crusher and related vibratory equipments.INTRODUCTIONMaterials can be easily broken by using the inertia force of the vibration exciter, which can effectively realize the selective crushing, reducing excessive combinations and the energy consumption, as introduced by Zhang in 2005. The initial micro crack between crystals in the material increases and new cracks can be manufactured because of the high frequency impact and the extrusion of the vibration crusher, so vibration crushing equipment can make it possible for any high strength brittle material to be broken theoretically. Inertia cone crusher and inertia vibration crusher have been successfully used in the treatment of metallurgical slag and construction waste, and it verifies the efficiency of vibration crushing."

Jan 1, 2016

By L. M. Oshinowo

The incorporation of advanced analysis tools, such as CFD, into the process plant design process has become possible through advances in commercially available computational fluid dynamics software and faster computers. Multiphase modeling is now typically employed in the design phase of process plant design at Hatch. The multiphase models include Lagrange-Euler and Euler-Euler treatment of the multiple phases. Additionally, mixture models with interface-sharpening algorithms are applied to the prediction of free-surface flows in complex geometry. CFD is applied to applications where traditional design rules are not applicable. The additional rigor of CFD modeling in 2D and 3D allows process engineers to come closer to realizing true virtual plant design. The objective of this paper is to outline the benefits and pitfalls in the application of multiphase modeling for rigorous design. Several application examples in the hydrometallurgical field will be presented.

Jan 1, 2005

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By Yves Fouquet

Results of the two main drilling operations on hydrothermal fields demonstrate that the two dimensional submersible operations need to be followed by drilling expeditions to study the third dimension of hydrothermal systems and understand hydrothermal and ore forming processes. Two types of environments were drilled recently in basaltic environment on slow spreading ridge, and on a sedimented ridge. Similar work has still to be done and targets to be discussed in other environments such as back-arc basins for felsic rocks environments and slow spreading ridges for ultramafic rock environments.

Jan 1, 2011

By H. Rossmanith

This contribution introduces the fundamental concepts of wave propagation and fracture mechanics which form the basis of electronic blasting, i.e. precise initiation timing using electronic detonators. The concept of Lagrange diagrams will be frequently used for the calculation of the delay time between blast-holes in a row and rows of blast-holes. The effect of burden and structural geology will be briefly touched. It is found that the advanced blasting technology based on the use of electronic detonators introduces a change of paradigm. It will be shown that knowledge in wave propagation and fracture mechanics is essential for the successful application of the new blasting technique in industry. In particular, the delay time, the wave speeds in the rock mass, the shape of the wave pulse and the acoustic impedance mismatch have become decisive parameters in advanced blasting. Utilizing the wave speed and wave shapes of detonations, large scale tests Utilizing the wave speed and wave shapes of detonations, large scale tests in various countries (Australia, Chile, etc.) have shown that optimal delay timing requires shorter delay times in conjunction with allowing for a wider drilling pattern and the use of a reduced amount of explosives, i.e. a lower powder factor. This seemingly contradictory arrangement is fully justified by using scientific principles in blasting, and converting blasting from an art to a scientific discipline.

Jan 1, 2003

By Paul W. Billwiller

Introduction In 1937, the Britannia Mining and Smelting Company, Limited, was carrying on an extensive exploratory diamond-drilling programme. Most of this drilling was done on the 4100 level, the lowest working level in the mine. One of the exploratory diamond-drill holes, at approximately 12,500 feet from the portal of the tunnel, encountered heavily mineralized stringers of chalcopyrite and sphalerite in silicified grey schist. The mineralization was encountered just to the hanging-wall of the green mottled schist at a point 350 feet south of the 4100 tunnel. To delimit this new orebody, drifts and cross-cuts were driven on 3500, 3800, and 4100 levels to the hanging-wall in the area of the projected mineralization. On the 3500 level, the top of the mineralized zone was encountered. The zone was thoroughly explored by drifting and diamond drilling. The mineralization, however, was not sufficiently concentrated to be of commercial grade. On the 3800 level, the zone was found to consist of disconnected stringers of chalcopyrite and pyrite. Drifting was continued to the west and a long lens-shaped area of grey schist containing fairly heavy stringers of chalcopyrite was delimited. This lens later proved to be very close to the top of the commercial mineralization of the No. 8 orebody. On the 4100 level, a diagonal cross-cut was driven to the footwall of the downward projection of the mineralized zone. Diamond-drill holes from this cross-cut indicated a zone of heavy mineralization. A drift was driven off the cross-cut parallel to the zone and some distance to the footwall of it. Further diamond drilling disclosed a mineralized zone approximately 300 feet long and 35 feet wide containing sphalerite, chalcopyrite, and pyrite. The foregoing development work indicated a fairly large lens of mineralization of sufficient concentration to be classed as ore between the 4100 and 3800 levels. To explore this mineralization at depth, long diamond drill holes, dipping at minus 57° and minus 80°, were planned from some point to the hanging-wall of the orebody. The 4100 level was not suitable for small development headings, due to wider gauge track and larger cars than on the levels above. Therefore, a raise was driven from the diagonal cross-cut on the 4100 level to a point some 70 feet above and just inside the footwall of the orebody. From the top of the raise, drifts were expanded east and west to delimit the ore zone. In addition, a long cross-cut was driven 350 feet to the hanging-wall, and drifts were opened east and west from the end of the cross-cut to provide diamond-drill stations for the exploration of the orebody at depth.

Jan 1, 1946

The number of railroad coal cars (open top hoppers), dominated rail car orders and deliveries in 1975 according to announcements made February 11, by the Association of American Railroads and the American Railway Car Institute. Acting to keep ahead of increased coal production, the railroads installed 21,748 new coal cars in 1975, the most since 1957. The 1975 installation resulted in a net increase of 6,560 coal cars and an overall gain of 4.5 percent in the total capacity of the hopper car fleet. With most of the new coal cars going into unit train service --where car utilization is greatest --the railroads actual coal-carrying capacity was increased far more than 4.5 percent. The AAR estimated that unit train operations now move 50 percent of all rail-hauled coal compared to only 42 percent 2 years ago. COBALT - The Societe Miniere de Tenke Fungurume (SMTF) copper-cobalt project in Zaire reportedly was suspended in January for an indefenite length of time. According to officials, the deferment resulted from a number of adverse factors, one of which was exceptional increases in capital costs. The project was scheduled for completion in early 1978, with an eventual production of 14.3 million pounds of cobalt per year. Reserves of cobalt were reported to be 505 million pounds. SMTF is a consortium and includes American, British, French, Japanese, and Zairian interests.

Jan 1, 1976

By N. Kinoshita, Y. Inada

The authors have proposed and discussed storage of low temperature materials such as LNG, LPG and frozen food in rock caverns. In this case, as the rock mass around the caverns will receive effects of low temperature, it is necessary to consider the thermal behavior and the stability of caverns. In this study, strength and deformation characteristics obtained by the uniaxial tension test and the compression test at low temperatures were discussed. Using the results, temperature and stress distribution around caverns when LNG was stored, were analyzed. Then thermal behavior of the rock mass around caverns was discussed. Die Autoren haben Lagerung von Niedertemperatur-Materialien wie LNG, LPG und tiefgefrorenen Nahrungsmitteln in Felskavernen vorgeschlagen und diskutiert. Da in diesem Fall die Felsmasse um die Kavernen den Effekten der niedrigen Temperatur ausgesetzt ist, ist es erforderlich, das Thermalverhalten und die Stabilität der Kavernen zu berücksichtigen. In dieser Untersuchung wurden Stärke-und Deformationseigenschaften, die durch ein-axialen Spannungstest und Kompressionstest bei niedrigen Temperaturen erhalten wurden, diskutiert. Mit diesen Ergebnissen wurden Temperatur- und Stressverteilung um die Kavernen bei Lagerung von LNG analysiert. Dann wurde das Thermalverhalten der Felsmasse in der Umgebung der Kavernen diskutiert. Les auteurs proposent et discutent l'entreposage de matériaux à basse température, tels que le GNL, le GPL et des aliments congelés, dans des cavités rocheuses. Comme, dans ce cas, la masse rocheuse entourant la cavité subit les effets des basses températures, il est nécesaire d'étudier le comportement thermique et la stabilité des cavités. Dans cette étude, les auteurs discutent des caractéristiques de résistance et de déformation, obtenues par essai de tension uniaxial et essai de compression à basse température. En se servant des résultats, ils analysent la répartition de la température et des pressions autour des cavités, lors du stockage de GNL. Ils discutent ensuite le comportement thermique de la masse rocheuse autour des cavités.

Jan 1, 2003

By Harry L. Siebert

A major Arizona highway project is jeopardizing site safety and security because of the lane rental policy. One million cubic yards of rock must be fragmented to provide two additional lanes parallel to the existing roadway. Traffic is stopped during blasting operations.

Jan 1, 1997

By P. S. Baker

CRU estimates that the global supply of metallurgical grade alumina (MGA) grew by 5 percent during 2005 to a little more than 61 Mt (67 million st). About 30.7 Mt (33.8 million st), or 50.3 percent, of that originated from Oceania (principally due to the commissioning of the CAR refinery in Australia) and Latin America. In this context, Chinese production surged by 20.5 percent year-on-year to 7.7 Mt (8.5 million st) on the crest of a 17-percent rise in that country’s primary aluminium production. Meanwhile, on the demand side, there was a 6.7 percent climb year-on-year in global consumption to 62.3 Mt (68.6 million st). This reflected a healthy demand for primary metal from aerospace, construction, packaging and passenger transportation (to a lesser degree) in the United States, China, Brazil, South Korea and India. So there was an overall supply deficit of more than 1.2 Mt (1.3 million st). This, combined with an 18.3-percent diminution in closing stocks (down to 35 days of requirement), lifted the average spot price of MGA by 17.6 percent year-on-year to US$448/t (US$406/st).

Jan 1, 2006

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Patiño E

Bioleaching is an established technology for the pre-treatment of refractory gold ores and concentrates and the leaching of whole ore copper heaps. In many cases, it offers economic, environmental and technical advantages over pressure oxidation and roasting. However for bioleaching to compete successfully with others pre-treatment processes it needs to be optimized with regard to the parameters that affect the bioleaching reactions and the growth of the microorganism involved. In this sense, this paper focus on the thermodynamic approach applied in bioleaching through of the definition of the growth system and it is thermodynamics analysis, the effect of heat production and energy dissipation on growth and thermodynamic analysis of growth kinetics and the effect of nonstandard conditions.

Sep 12, 2005

Minerals Industry - 5 Year Outlook AusIMM sponsored project Positioning the Minerals industry for the 21st Century Does this seem right for New Zealand?  To ascertain the industry's perceptions of issues and capacity to address them: Industry context and issues Capabilities of professional staff Access to professional staff Balancing supply and demand Industry must do it. Cannot wait for others.   Some observations... Negative image - constrains capacity to influence community and government Major repositioning of professional staff competencies required Existing organisational arrangements and capabilities are under pressure to change Difficult to access professional staff of required capability Facing significant external challenges - with real concern about capacity to address them Prevailing culture not suited to needs of the future High level felt need for change The industry has a choiceà We can define where we want to be and act decisively Or We can respond to the future as it unfolds.

Jan 1, 2000

By Tim O’Neil

The US Bureau of Mines and the Santa Cruz Joint Venture (SCJV) are working on a production-scale, in situ copper recovery project in Arizona. The research is being conducted at the Santa Cruz site, located 11.2 km (7 miles) west of Casa Grande, AZ (Fig. 1). Santa Cruz is a 1.36-Gt (1.5 billion st) porphyry deposit averaging 0.6% Cu, of which 65% is oxidized, concealed beneath post-mineral alluvium at depths of 365-914 m (1500-3000 ft). The Bureau and the SCJV will evaluate in situ mining as a method for extracting copper from this previously unmined deposit. Research objectives of the Santa Cruz project are: - to demonstrate that an in situ research test can be operated in an environmentally acceptable manner ; and * to operate an in situ well pattern long enough to develop information on copper recovery and economic feasibility data. In situ mining of copper from undisturbed deposits has not been attempted commercially. There are several potential advantages with in situ mining: less exposure of miners to hazards, lower pital costs for the mine and plant and lower operating costs. In addition, there are no pits, dumps or tailings, which means less environmental impact.

Jan 1, 1991

By Tom Barczak, Julian Restrepo, Zach Agioutantis

"The Alpha Foundation for the Improvement of Mine Safety and Health, Inc. (Foundation) was established as part of a Non-Prosecution Agreement (Agreement) entered in December 2011 by the United States Attorney's Office for the Southern District of West Virginia, the United States Department of Justice and Alpha Natural Resources, Inc. (""Alpha"") and Alpha Appalachia Holdings, Inc. This Agreement was related to the explosion at Upper Big Branch Mine, an underground coal mine owned by Performance Coal Company, a former affiliate of Massey Energy Company, which Alpha acquired in June 2011. Pursuant to that agreement, Alpha agreed to establish a trust to fund projects designed to improve mine health and safety by providing $48,000,000 into the trust. The mission and vision of the Foundation are as follows:Mission: To improve mine health and safety through funding research and development projects by qualified academic institutions and other not-for-profit organizations.Vision: To enable miners in the future to be free of work-related injury or disease by the implementation of the results of the projects funded by the Foundation and undertaken by the best researchers from any discipline that can contribute.The focus of the research effort is not limited to coal mine explosion prevention, and in fact encompasses the entire spectrum of health and safety, addressing issues in both underground and surface mining operations in all mining sectors. Four major focus areas are identified (see Figure 1): 1) Health and Safety Interventions; 2) Mine Escape, Rescue, and Training; 3) Safety and Health Management and Training; and 4) Injury and Disease Exposure and Risk Factors.The Foundation is seeking to expand the knowledge base of mining safety and health information that can lead to resolving complex mining problems. To that end, the projects funded by this effort are designed to provide a spectrum of knowledge potentially encompassing the following:• Surveillance data - Collect and analyze surveillance data that better documents the prevalence and trends of occupational safety and health across the mining industry."

Jan 1, 2016

Attempts to rationalise the geological environment of nickel sulphide deposits associated with Archaean ultrabasic rocks has produced much speculation as to the origin of the sulphides and the relative importance of geochemical, mineralogical, textural and structural characteristics of the host rocks. From an economic viewpoint the object of such work is to establish geological criteria which can be used as an exploration guide. Exploration procedure for nickel sulphide mineralisation of the 'Kambalda type' (Hudson, 1972), which occurs at or near the basal contact of Archaean ultramafic flow units and lenses consisted of geological mapping, surface prospecting with soil sampling and rock geochemistry.

Jan 1, 1987

By H. A. Dierks, H. B. Link

The purpose of this investigation was to develop a practical feeder apparatus to introduce comparatively large pieces of coal and similar material into a pipeline under pressure in connection with the vertical hydraulic transportation of solids , termed " hydraulic hoisting . " This method of hoisting the precrushed run - of - mine product of an underground mine has been given unusually wide attention abroad and could be of considerable significance to the U.S. mining industry in its search for operating improvements and cost reduction . A lock-hopper assembly was developed after a series of sinking velocity tests were made by dropping anthracite in a column of water . The system functioned reliably as an automatically operated feeder apparatus .

Jan 1, 1964