Search Documents

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .0, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

Jan 1, 1999

By James C. M. Li, J. Weertman

James C. M. Li (United States Steel Covp.)—The author has discovered a single analytical relation between the minimum, or the steady-state, creep rate and the applied stress confirming a statement made earlier by orn" that such relation should exist and should reduce to the power law at low-stress levels and to the exponential law at high-stress levels. However, as pointed out by the author, all the available theories of creep are not adequate to explain such a single relation. Inspired by such a statement, I have made a suggestion concerning a possible explanation13 of the new relation. This is based on the concept that the rate-controlling step is the cooperative motion of a short dislocation segment. The nature of and the reason for the cooperation have been discussed13 as well as the reason why the motion of the dislocation could be controlled by the mobility of the short segments. A natural short segment has been proposed13 to be the node formed at the intersection of two dislocations. The reason why the node may contain only a few atoms has not been discussed and the application of the proposed model to all the metals and alloys reported in this paper has not been attempted. It seems appropriate to include these in this discussion. The model was partly inspired by the substructure recently observed in the electron microscope on creep specimens. One such example is shown in Fig. 48 in Darken's Campbell Memorial Lecture. The substructure is a collection of dislocation intersections and irregular networks. No pileups have ever been observed in such specimens. A closer look at the network indicates that one set of dislocations is more straight than the other set sug- gesting that the other set may be mobile in the plane of the net. Since, for the network to survive the creep deformation, some dislocation reaction has to take place at the intersection of the two sets of dislocations, the mobile dislocation, even if it can slip in the plane of the net, will have difficulty in moving at these intersections. To illustrate, an idealized network is shown in Fig. 9. The thin lines represent the set of dislocations which are mobile and can slip in the plane of the net except at the nodes which are formed at the intersection of the two sets of dislocations. The other set of dislocations, represented by the thick lines, may have a Burgers vector which is not parallel to the plane of the net, and therefore may be immobile. Because of this nonparallel Burgers vector, the Burgers vector of the node, which is avectorial sum of the Burgers vectors of the two sets of dislocations, will also be nonparallel to the plane of the net. Therefore, the node cannot slip in the plane of the net and the set of mobile dislocations will have to drag the node along as indicated in Fig. 9. Now the problem is how many atoms could be involved in the nodes. Exact calculation of the length of the node is a difficult task especially since the length should be a steady-state length and not an equilibrium length. An estimate of the equilibrium length can be made by balancing the line tension of all the dislocations. The results would be a small fraction of the length 1 between nodes as shown in Fig. 10. In some instances such a calculation shows that the node will not be formed. But, since the calculation is only approximate, it does not rule out the possibility of the formation of a short node. In other instances the equilibrium length of the node is an appreciable fraction of I. Such a node would

Jan 1, 1963

By F K. Buckley

Currently, Kanieri Gold Dredging Limited operates the only large scale gold dredging operation in New Zealand. It dredges a claim in the Taramakau River using the bucket dredge 'Kanieri'. This dredge, a 'Yuba' type, was designed and built in the 1930s. On the current claim it works about 12 hectares of ground a year. Because of its design, the tailings from the 'Kanieri' make land restoration difficult. This was unimportant until it commenced its new claim ML-32-310 in 1978. The conditions, attached to this licence required it to restore the land for afforestation, the designated use fur the Crown land being mined. With the company planning to work future claims on the Grey River, it decided to undertake restoration work on the Taramakau to demonstrate its capability of establishing pasture land on tailings, a more difficult task than restoring the land for afforestation. After two years and the restoration of two blocks totalling 22 hectares, reasonable pasture establishment has been achieved. Much has been learned to date and further refinement of the techniques used will take place over the next two years. The quality of the tailings produced has improved as a result of the limited modifications possible on the existing dredge. This has been significant in achieving better results. The knowledge gained will be taken into account in future dredge design. Both the Company and its Consultant are confident of achieving satisfactory restoration of dredge tailings for pasture land.

Jan 1, 1981

By R. A. Hill, J. D. Pitts

"Long distance slurry pipeline systems have been successfully trans-porting steam coal, iron concentrates, copper concentrates and limestone for an aggregate of nearly 60 years and nearly three billion ton-miles annually. A phosphate concentrate pipeline is nearing start-up and systems for coking coal, lead/zinc concentrates and fly ash are planned. The solids pipeline concept, first patented in the early 1900's and commercialized in the 1950's, is now a proven technology providing an economic, environmentally pleasing and safe method for long distance bulk transport.The challenge for larger tonnage and longer distance movements of solids, for traversing increasingly rugged terrain in grass roots mineral developments, for transporting untried materials and for shipping more economic forms of proven materials still remains. This has necessitated continued refinements and optimization of the technology. The economic and environmental incentives for slurry pipelines when compared to other transport alternatives has justified substantial activity in this area. The scope of planned systems in coal, iron and other minerals is indicative of the firm place slurry pipelines will have in worldwide mineral development.In this presentation, the state-of-the-art in long distance slurry pipelines is reviewed with a focus on major systems of interest to the mineral processing industry. An overview of new developments in the application of this concept is presented, and finally, a projection of the future of pipelines in mineral development both worldwide and in Canada is discussed."

Jan 1, 1978

By Steve Kral

Mining is a risky business. The cost of exploring for new mineral deposits is high and the success rate of finding one worthy of development is relatively low. And once a deposit is identified, there is no guarantee that it will become a mine. Mining companies have to spend a lot of time and money on due diligence, prefeasibility and feasibility studies, and sustainable development and environmental issues before deciding whether the deposit will become a profitable mine. And then there are the millions of dollars spent in developing the deposit and building a mine. No wonder the mining industry has trouble attracting investment capital. Companies take a large risk in developing reserves and investors take a similar risk in investing in them. So mining companies must be as accurate as possible in determining mineralization that makes it to reserve status. After all, reserves are a company’s most important asset and one of the critical factors analysts and funding sources look at when determining if a mine or mining company is worth the risk.

Jan 1, 2003

Small scale gold mining operations in Papua New Guinea (PNG) have been observed to use very low flow rates of water in sluice boxes. In a series of laboratory experiments carried out to determine whether this approach was unsatisfactory or not for their situation, indications were obtained that it had some advantages in the recovery of fine gold but at the cost of considerable throughput. The separation mechanisms operating in such a system are analysed.

Jan 1, 1986

The following is a list of members who died in 1928. It is compiled from reports to the Secretary's office. Biographical sketches published in Mining and Metallurgy are indicated in the last two columns. Issue Containing Year or Date or Biography Election Name Death 1928 Page 1914 Adams. David T.................... July 22 October 471 1905 Aguilera. Pedro................... May 3 October 469 1902 Althouse, H. W.................... NOV. 3 December 559 1920 Averill: C. C...................... July 9 October 471 1915 Baldwin, C. Kemble............... Aug. 9 October 471 1926 Barquist, Walter C............... NOV. 14 June 298 Barron,* Clarence Walker......... Oct. 2 November 511 1917 Beasley, Fred E.................... Aug. 31 October 471 1901 Belden, S. B....................... May 15 July 333 1927 Binney, Edwin, Jr.................. Dec. 29 February 96 1915 Bonsall, James Malcolm............ Feb. 12 June 284 1917 Boyle, John....................... July 12 December 561 1913 BradEn, Eugene B............. Jan. 29 March 157 1889 Bulkley, Frank.................... Mar. 25 May 240 1896 Callaghan, J. T., Jr............... Apr. 1 1892 Chalmers, George.................. Feb. 4 April 197 1898 Clark, Josiah H.................. May 7 July 333 1887 Copeland, F. K............. Nov. 10 December 561 1915 Cunningham, B. L11............... Dec. 6 August 294 1888 Dana, R. T........................ Aug. 20 December 559 1907 Dennis, Clifford G............... Dec. 28 March 1 1920 DeVenny, Thomas................ Feb. 13 April 197 1882 d'Invillier-, Edward V........... Jan. 4 March 157 1884 Duncan, M. M..................... Dec. 17 February 96 1924 Dyrssen, WaldemaR ............... Aug. 4 October 471 1906 Edmondson. H. W................ Dec. 21 February 1884 Emmerton, F. A.................. Oct. 9 June 298 1911 Eu, S. H............................ July 20 February 1917 Farrand, Ira W.................... Sept. 6 October 469 1900 Fell, E. Nelson...........•......... Mar. 25 May 231 1918 Fenton, Clarence M.............. October Junet 298 1908 Ferraris, Erminio................. Sept. 22 June 298 1914 Galloway. A. D. R............... December April 215 1924 Grant, A. W., Jr................... .4pr. 5 June 285 1917 Grant, Clifford G............... Jan. 26 January? 37 1918 Grant, Frank E.............. Jan. 14 September 417 1921 Gunderoth, C. J.................. Feb. 15 1897 Harms, Ernest..................... Aug. 12 November 512 1891 Hartrick, J. S..................... Feb. 9 June 285 1925 Hochschild, Berthold.............. Jan. 24 April 197 1917 Hutton, L. W...................... NOV. 3 January 37 1894 Jenning", S. J...................... NOV. 17 December 560 1925 Jones, J. Ravenscroft............... Jan. 29 March 157 1880 Jones, J. T......................... May 4 June 284

Jan 1, 1929

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By Gerhard Braüner

The present knowledge on ground movements and mining damage is mainly based on observations made when mining seamlike deposits. The studies, rules, and regulations in different countries agree in that the differential ground movements, especially the strain, account for the damage to structures. Accordingly, large buildings are particularly susceptible. The opinions on what amount of ground deformation induces what degree of structural damage are not quite uniform. Mining damage can be reduced or prevented by structural and/or underground precautions. The latter comprise measures for generally reducing the ground movements (leaving pillars, filling, partial extraction) and for reducing temporary movements (rapid extraction, specially arranged workings). Because the differential movements decrease with increasing depth of mining, safety pillars are largely dispensable at greater depths. Shafts are mainly affected by the vertical derivatives of rock displacements, but extraction in the vicinity of shafts is feasible even under difficult conditions. The theoretical concept of the ground movement process established in part 1 of this work is in qualitative agreement with the facts herein observed. As a quantitative approach, it should be applied to calculating ground surface movements rather than rock movements about underground openings. It can be extended by introducing more detailed strata characteristics.

Jan 1, 1973

By Edgardo Orderique

Southern Perú Copper Corporation ha desarrollado un programa de reevaluación de las reservas para optimizar cada etapa del proceso y así llegar a las reservas mencionadas. En este sentido, el presente texto desarrolla el esquema de optimización de una secuencia anual de minado. El proyecto comprende la realización de de perforaciones en zonas llamadas geometalúrgicas, con el fin de realizar pruebas metalúrgicas y definir el comportamiento del mineral en la concentradora y lixiviación. También se incorpora el concepto de índice de solubilidad, parámetro que sirve para diferenciar adecuadamente un mineral económico para flotación del de lixiviación y finalmente, se optimiza la secuencia anual de minado y disposición de material en botadero. En consecuencia, es importante determinar el uso de software y hardware adecuado para planeamiento de minado, ya que depende de la magnitud de la mina como en el caso deCuajone.

Sep 13, 2001

In this paper a quantitative deterministic risk modelling approach (Quadrim) is introduced. The mathematical framework and equations for quantifying uncertainty within and aggregating across value chain nodes from error propagation techniques is proposed and discussed. A case study and worked examples, based on a hypothetical mine are then presented. This illustrates how uncertainty from the mining and economic value chains can be handled in a typical net cash flow calculation, and how this can be translated to a risk model. It is then illustrated that current valuation techniques do not just result in an information gap for decision makers. Traditional approaches such as discounted cash flow (DCF) analysis and truck and shovel productivity analysis, which do not take into account uncertainty in input values, can result in potential bias in estimates such as net present value (NPV) or equipment hours

Sep 26, 2011

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, 'the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, 'the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

By J. M. McKinley

Mineral exploration programmes around the world use data from remote sensing, geophysics, and direct sampling. On a regional scale, the combination of airborne geophysics and ground-based geochemical sampling can aid geological mapping and mineral exploration. Since airborne geophysical and traditional soil-sampling data are generated at different spatial resolutions, they are not immediately comparable due to their different sampling density. Several geostatistical techniques, including indicator cokriging and collocated cokriging, can be used to integrate different types of data into a geostatistical model. However, with increasing numbers of variables the inference of the crosscovariance model required for cokriging can be demanding in terms of effort and computational time. In this paper a Gaussian-based Bayesian updating approach is applied to integrate airborne radiometric data and ground-sampled geochemical soil data to maximize information generated from the soil survey, enabling more accurate geological interpretation for the exploration and development of natural resources. The Bayesian updating technique decomposes the collocated estimate into two models: prior and likelihood models. The prior model is built from primary information and the likelihood model is built from secondary information. The prior model is then updated with the likelihood model to build the final model. The approach allows multiple secondary variables to be simultaneously integrated into the mapping of the primary variable. The Bayesian updating approach is demonstrated using a case study from Northern Ireland. The geostatistical technique was used to improve the resolution of soil geochemistry, at a density of one sample per 2 km2, by integrating more closely measured airborne geophysical data from the GSNI Tellus Survey, measured over a footprint of 65 x 200 m. The directly measured geochemistry data were considered as primary data and the airborne radiometric data were used as secondary data. The approach produced more detailed updated maps and in particular enhanced information on the mapped distributions of zinc, copper, and lead. The enhanced delineation of an elongated northwest/southeast trending zone in the updated maps strengthened the potential for discovering stratabound base metal deposits..

Jan 1, 2014

By C. O. Swanson

CALCULATING the average grade of a gold deposit is a problem that presents certain unique difficulties. Particularly troublesome is the fact that the average of the samples taken from a deposit is likely to be higher than the grade of the ore that is eventually mined, even when allowance is made for dilution and other factors resulting from the mining operations. It would seem that this situation is due to the presence in the deposits of structural peculiarities which have not been properly taken into account, since estimating the average grade of the broken ore produced from the deposits does not present the same difficulty. It is therefore evident that structural considerations are of prime importance in estimating the grade of a deposit. This fact is clearly realized and taken into account in cases where the boundaries of the orebodies and the variations within them are easily recognized. But in many gold deposits this condition is not satisfied, a circumstance which can be regarded as the main source of difficulty. Lacking definite information concerning the structure, we are apt to use certain procedures which are either empirical or based on general probabilities.

Jan 1, 1945

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996

Remediation of Mine Seepage at Batu Hijau

Sep 13, 2010

By Jerry J. Ran

In open stope mining borehole deviation is one of the main factors affecting the blasting results. Though previous research has identified some actual deviation patterns, these studies are unable to relate the hole deviation pattern with the blasting results and therefore it is not possible to modify the design or take remedial measures based on the prediction of the blasting results. An alternative to the conventional method for borehole surveying is the in-hole probing techniques. With their inherent errors, it is important to evaluate these surveying systems under conditions of different mine sites. The lack of available assessment methods has limited the application of these techniques. In this paper some of the characteristics of the actual hole deviation pattern are discussed based on data from surveying production holes in six stopes. A method of predicting the blasting results is proposed by considering the borehole deviation pattern. Based on the prediction stope design can be modified or further surveying is carried out to improve the blasting results. The tolerable error is introduced to relate the surveying error with the drilling pattern and therefore it is possible to assess various in-hole-surveying techniques.

May 1, 2002

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

The passage of chloroform vapour in a carrier of oxygen through two nickel sulphide ores heated to 380°C converted the nickel to the water soluble chloride form. In one ore the nickel (2·75 per cent) was presentas violarite ((Ni, Fe)3S4) whereas in the second it was present as pentlandite, ((Fe, Ni)9S8) (4·9 per cent Ni).A similar technique was utilized to convert nickel in nickeliferous laterites (1·6 per cent Ni) into a soluble chloride using town gas instead of oxygen as a carrier.With both techniques greater than 90 per cent extraction was achieved.

Jan 1, 1972