Search Documents

By M. A. Trevits, T. A. Gray, L. M. Crayne, P. Glogowski

Mine seals can he remotely constructed in underground coal mines through vertical boreholes when direct access to a fire is impossible or considered to he too dangerous. This method has great merit because the boreholes can be drilled to specific mine areas, and the seals can be positioned close to a fire zone. The technology however can be largely ineffective if the constructed seals do not provide of effective barriers to airflow or if they cannot he used to impound water and other inert materials. Unfortunately, no viable alternatives exists to sealing the entire mine to the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL). Under this effort. Howard Concrete Pumping Company and GAI Consultants Inc. have joined forces to evaluate a potentially significant improvement to the current state of the art. This paper covers the development o f novel technology or rewrote mine seal construction, the evaluation of rite materials used, the construction practice and the Fellow-up testing.

By J. Hansen

This paper has been written for presentation during the Open Pit Mining Session at the SME Annual Meeting and Exhibit, Denver, Colorado, February 26 to 28, 2001. The paper addresses the application of automated monitoring of electric rope shovels to improve performance and blasting technique.

Jan 1, 2001

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011

By J. I. Muñoz González

El presente trabajo verifica la utilidad de la incorporación de algoritmos de inteligencia artificial (IA) en cuanto a mejorar los resultados obtenidos en campañas de sondajes de exploración. Tomando la información geológica, geoquímica y geofísica de un proyecto real de exploración, se simularon 3 campañas posteriores y consecutivas, utilizando algoritmos de “boosted regression”. Luego fueron comparados con los resultados reales de los mismos.

May 1, 2008

By D A-F Batchelor

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.South-East Asia represents the world’s most productive tin province, mainly from placers. Kalimantan has been a major diamond producer, while in the 1980s a placer gold rush occurred in Indonesia and Malaysia. Reviewing extensive geological and mining data highlights phenomenal palaeo-environmental changes in the Sundaland region, interpreted to be responsible for generating ‘giant’ placers. Correlation of the Late Cainozoic stratigraphy has been facilitated from mine exposures and drill holes distributed throughout Peninsular Malaysia, the Indonesian Tin islands and Kalimantan, including contiguous marine areas with extensive shallow seismic profiling data. Knowing the association of rich placers with palaeo-environmental episodes and stratigraphical units has been helpful to facilitate their discovery. All three placer commodities responded similarly to region-wide landscape evolution following Mio-Pliocene high sea levels. Commencing with major regression, important stages comprised: a long period of landscape stability with deep weathering during the maximum Sundaland extent gradually rising sea levels/precipitation initiated slumping of mineralised regolith to form fans, later reworked by braided streams with aggradation (Old Alluvium); during episodic pluvial periods downcutting upgraded placers significant change occurred around Middle Pleistocene time with peneplanation and pedogenesis from Late Pleistocene time ‘modern’ fluviatile deposition (Young Alluvium) filled incised V-shaped valleys.Placer seams show systematic variation in stratigraphic position, in particular cassiterite especially occurs in the Old Alluvium (equivalent Upper Dahor Formation in Kalimantan). Gold is commonly richer in gravelly younger deposits, partly because of secondary precipitation within permeable alluvium. Reworked diamonds are predominantly concentrated especially in younger fluviatile alluvium.CITATION:Batchelor, D A-F, 2015. Conceptual exploration for tin, gold and diamond placer deposits in ‘Sundaland’ (Indonesia and Malaysia) by understanding the late Cainozoic stratigraphic context, in Proceedings PACRIM 2015 Congress, pp 499–506 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By Glen D. Frank, Jeremy P. Theys, Mina M. Shinouda, Gary W. Gilbert

PURPOSE OF THE PROJECT The Big Walnut Augmentation Rickenbacker Interceptor project began in 1995with the preparation of the Scope of Services for the design of the Rickenbacker Interceptor, with service to and around the Rickenbacker Air Force base. The air base was soon to be placed under civilian control through a Port Authority, with an expected influx of businesses and services, requiring increased sanitary service capability. Due to political differences regarding annexation and other issues, the project was placed on hold. In mid 1996 the Scope of Services was rewritten with more emphasis on a tunneling option, but still only addressing the air base and surrounding tributary are a sanitary service requirements. The consultant selection process began in late 1996 with the Request for Statements of Qualifications issued in December. Three firms were selected to furnish proposals based on the revised Scope of Services that now included requirements for hydraulic modeling of the service areas and the Big Walnut Outfall (BWO) and an expanded soil investigation requirement. All three firms were requested to make presentations to the selection committee, with the committee selecting URS Greiner for further consideration and negotiation. A contract was entered into in August of 1997with URS Greiner. The major sub-consultants were Lachel and Associates, Inc., H.R.Gray and Associates and Solar Testing Laboratories, Inc. The project began with geological investigations, preliminary soil borings, well investigations, tributary area evaluations, hydraulic modeling of the BWO system and research into other projects planned for the Rickenbacker airport and surrounding area. The hydraulic modeling of the BWO and the proposed Rickenbacker Interceptor confirmed that the BWO suffered wet weather surcharging and would require augmentation to properly convey the future flows to the Southerly Wastewater Treatment Plant(SWWTP). The project scope expanded to include evaluation of both the Rickenbacker Interceptor and the Big Walnut Augmentation projects. Both projects previously identified in the Capital Improvements Program. The work on the expanded scope for the Big Walnut Augmentation and the Rickenbacker Interceptor began with the evaluation of a parallel 2.75 meter (108") diameter augmentation sewer from SWWTP to S.R. 317and Parsons Avenue, then continuing east along S.R. 317 as the Rickenbacker Interceptor. The parallel 2.75 meter (108") sewer had been planned for in the design of

Jan 1, 2007

By H. P. LeVan

The aced for reliable reserves of the essential element, manganese, has been a continuing concern of the Federal Government for more than three decades. Because of the increasing vulnerability of outside sources of supply efforts have been intensified to find a means for beneficiating United States domestic deposits. The deposits of most interest would of necessity be near, or have access to, suitable transportation to processing plants. The Georgia manganiferous iron deposits represent some 10 million tons4 of ore readily available to southern iron and steel industries, if a manganese recovery process capable of functioning in the presence of large quantities of iron can be developed. In addition, a successful method for beneficiating the Georgia ore could produce a significant quantity of high-grade iron concentrate. The Differential sulfatization process developed 47 the Bureau of Mines5 seemed to be well suited for this application, particularly because it results in low concentrations of iron in the leach liquors with relatively complete extractions of manganese. In this process, manganese in the presence of iron is preferentially reacted with sulfur dioxide at elevated temperatures and subsequently extracted with water.

Jan 1, 1962

Various steps, and complete sequences, for the recovery of lead and zinc from a mixed sulphide concentrate, high in silica and pyrite, have been tested.Oxidation steps of roasting in air or in a sulphating atmosphere and use of aqueous acidic, ammoniacal, and near neutral oxidation media were compared. Oxidation roasting or use of acidic media appeared most useful. Procedures for dissolution of zinc from calcines using sulphuric and sulphurous acid to avoid silica gelation problems are compared and a direct leaching procedure with sulphuric 'acid at controlled pH shown to be the most useful.Methods for the removal of germanium, nickel, and magnesium from zinc sulphate solutions prior to zinc electrodeposition were tested. The recoveries of zinc from ammoniacal solutions by electrolysis and distillation are compared.The dissolution of lead compounds from the residue of zinc extraction by amine and ammoniacal ammonium sulphate (AAS) solutions Was tested. Lead, sulphide was precipitated in filtera'ble form from AAS solutions. The reduction of lead sulphate to lead sulphide with sulphur was difficult, but possible. The various steps were used to deveiop five complete processing sequences, of which two were shown to be technically feasible and have potential economic viability.

Jan 1, 1975

The State of New South Wales is highly favoured in having vast deposits of coal adjacent to and within easy reach of the coastal Ports. Not only is the quality of the fuel generally superior to any found in the other States, but it is greater in extent than in any other part of the Continent. For interesting and reliable details of the history of the discovery of coal, the geology of the coal bearing strata, analysis of the various coals and other valuable data, the readers are referred to the book recently issued by the New South Wales Government, entitled The Mineral Resources of New South Wales, by Edward F. Pittman, A.R.S.M., etc., by the direction of the Hon. T. L. Fegan, Minister for Mines. The mining community is indebted to the Minister for having had published the most valuable condensed record of the mineral resources of the State extant.For the purposes of this paper we will only give such a general description of the coal fields as will make it intelligible in connection with the subject of the coal mining in the State of New South Wales.

Jan 1, 1904

By R. J. Charles

F. C. Bond: This is an outstanding paper on comminution theory and represents a considerable advance in mathematical formulation. It clears the way for a discussion that should ultimately decide whether the work index should be considered as a parameter according to the Third Theory or as a constant. In the empirical differential equation dE = —Cdx/x [1] either Corn must be treated as a variable to satisfy known crushing and grinding conditions. The author has chosen the exponent n as the variable, with C as a constant. According to the Third Theory, in the general case n is a constant equal to 3/2, and C is a variable related to the work index Wi. If x is placed equal to P (the size in microns which 80 pct of the product passes) and F is the size 80 pct of the feed passes, then C equals 5 W1, and dE = 5 -5 Widx/x = 10 Wi 10 Wi w = vP vF which is the basic equation of the Third Theory. It is apparent that this integration involves the error of treating the parameter Wi as a constant, just as the author's treatment involves the error of integrating his variable n as a constant. These errors are probably relatively unimportant, considering the small range of the variables. When more is known about the factors contained in the work index, Eq. 1 can be revised as a partial differential equation. The Third Theory exponent of 1/2, or n = 3/2 in the Charles' differential equation (Eq. l), was not chosen primarily because it is the average between the Kick and Rittinger exponents; this may be merely fortuitous, since it is illogical to define truth as the average between two errors. It was first discovered from the study of a large mass of crushing and grinding data and confirmed by laboratory testing. The general correspondence of the Third Theory equation to actual crushing and grinding results over the entire size reduction range argues strongly that a fundamental phenomenon is involved. The a posteriori theoretical explanation of the constant Third Theory exponent is that the work done in breaking rock is proportional to the length of the crack tips formed. Compressive force applied to the rock results in deformation and strain energy. When this locally exceeds the breaking strength a crack tip forms, the surrounding strain energy flows to the crack tip and extends it to split the rock, with release of the energy as heat. Under rapid impact the crack tip may form before the strain has reached equilibrium, resulting in less energy expenditure and probably a coarser product. In any case, the elastic limit of a brittle material is practically the same as its breaking strength, and the work necessary to form the crack tip is the work required to break. The crack length of a ton of broken rock cannot be measured directly. However, the particle shapes of feed and product are similar, and the crack length is considered equal to the square root of one half of the new surface area formed. It is, therefore, proportional to 1/vD, where D is the equivalent product particle diameter. This is the basis of the Third Theory equation. Many secondary factors can be imposed upon the crack length breakage. These may cause the Third Theory work index to increase or decrease somewhat as the product size becomes finer. The work index is properly a parameter rather than a constant, making it an increasingly valuable practical criterion of the work input required in crushing and grinding.

Jan 1, 1959

By Y. L. Su, S. Vongpaisal, H. A. Smith

"It is extremely difficult for a mine's central control room operator to control peakpower demands and to maintain normal materials handling operations at the same time. An investigation of the Falconbridge Strathcona Mine 's central control room has revealed that there are more than eight thousand possible combinations of ""situations"" that can arise. For such a circumstance, an expert system can become a very valuable tool to assist the operator in taking the most appropriate and timely action.A forward chaining expert system module has been developed for this application. The module is based on Level 5 ObjectTM software. It is graphics oriented and user-friendly. Training requirement is minimal.ForewordThis paper has arisen out of work carried out by YLS Associates and Falconbridge Limited as part of a contract between Falconbridge and the Department of Energy, Mines and Resources, Government of Canada, on the application of expert systems in mining operations.IntroductionThe electrical bill charged to large consumers by Ontario Hydro is based upon two elements: demand and energy consumption. The demand is the peak kilowatt level that the consumer has required during a monthly period. It is not uncommon for the demand portion to be as much as one third of the monthly bill. Energy consumption is the total kilowatt-hour s (kWh) consumed during the period.Ways to reduce the energy consumption part of the electrical bill involve utilizing energy-efficient equipment and operating machines in off-peak hours when a lower energy rate is charged. Maintaining the peak power below a critical level may require that simultaneous usage of major pieces of equipment be avoided. A 3000 kW skip run at an inopportune time could cost a company an extra $30,000 in that month's power cost.Potential disadvantages associated with peak power control are lost production due to work stoppage and increased operating costs due to the need to employ extra personnel. Most companies find these matters relatively easy to deal with and with incentives provided by Ontario Hydro, actively pursue this facet of energy savings (Harju , 1991)."

Jan 1, 1993

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

CONTENTSIntroductionNorthern ExplorationDrive ConceptionGeneralDriving CrewDrive Cross Section and Track DetailsVentilation by Electrically Driven FanTemperatures and HumidityFan PerformanceRock Drill Carriage and Rock DrillsStandard Drilling RoundElectric Firing from Power MainsExplosives and DetonatorsCharging and FiringMechanical Loading and Electric HaulageOperating CycleStatisticalEquipmentAcknowledgementINTRODUCTION.The driving project described in :this paper is one of greater magnitude than usual for the Broken Hill field, and in the execution of the work a departure was made from long-established local practice by the introduction of mechanisation. The primary object of the drive is to provide sites for gaining information regarding the behaviour of the ore-bodies well beyond the limits of the present exposures.Due to thermal conditions, the major portion of the work was done on a six-hour shift basis, in contrast to the normal one of seven hours, with a five-day week.

Jan 1, 1946

By Kamilla Giló Santiago

Nesse trabalho para caracterização metalúrgica dos revestimentos compostos pela mistura das ligas AWS ERNiCrMo - 3 E AWS ERNiCrMo - 4 soldados pelo processo MIG/MAG duplo arame foram realizadas análises micrográficas por meio de microscopia eletrônica de varredura. Observou-se semelhança entre os precipitados do topo e da interface do metal de solda com o substrato e que a microestrutura obtida com a soldagem das duas ligas, simultaneamente, resultou na mistura das microestruturas, obtidas a partir das soldagens com cada uma das ligas de forma isolada. O ensaio para avaliação do desempenho da mistura quanto à resistência a corrosão foi realizado conforme a norma ASTM - G 48, método C para determinação da temperatura crítica de pite da mistura das ligas. Foram utilizadas amostras dos revestimentos com maior e menor diluição. O resultado do ensaio apontou que os revestimentos soldados apresentaram temperatura crítica de pite superior ao da liga AWS ERNiCrMo-3 e semelhante ao da liga AWS ERNiCrMo-4.

Aug 7, 2018

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

By Aquiles Vivar

Ante los problemas de sismicidad inducidos por el sistema de minado en la Compañía minera Milpo, se planteó una solución a través del sistema de monitoreo sísmico único, donde se da una distribución espacial de 20 censores entre uniaxiales y triaxiales distribuidos en 3 niveles de producción en el área de influencia de las actuales operaciones para así ubicar, cualificar y cuantificar el fenómeno a efectos de realizar los análisis interpretativos del caso. En ese sentido, el presente texto describe el sistema de monitoreo, cuyo software sísmico está diseñado para determinar nuevas estructuras formadas a partir de los eventos sísmicos pre existentes reactivadas por la sismicidad inducida, así como el desarrollo de planos de isocontornos que permiten la diferenciación entre zonas de altos y bajos esfuerzos.

Sep 9, 2007

By Sutham Niyomwas

Synthesis of alumina-mullite-silicon carbide composite (Al2O3-Al6Si2O13-SiCw) was obtained in situ by carbothermal reduction of a mixture of kaolin and two different silica sources. The carbothermal reduction was carried out in a horizontal tube furnace under flow of argon gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of alumina, mullite and silicon carbide in the form of whiskers. The effects of adding two different silica sources of rice husk ash and silica powder to the mixture of kaolin and activated carbon were investigated. XRD and SEM analyses indicate complete reaction of precursors to yield Al2O3- Al6Si2O13-SiC as product powders, with the SiC having whisker morphology.

Jan 1, 2006

By D. D. Blue

To insure domestic production of aluminium for, essential civilian and defense uses, the Government, under authority of the Defense Production Act of 1950, programed and promoted an aluminum-expansion program that will more than double the primary production capacity that existed in 1949. In view of this vastly increased production, the raw materials, with respect to both quantity and sources, are reviewed. The raw-material consumption pattern, the requirements during an expansion period when excess quantities of materials for starting up new facilities are consumed, and the probable requirements for production of 1.7 million tons per year of primary aluminum are discussed. The raw materials that presented the most difficult supply problems were bauxite, electrical power, and fluoride salts, and the supply pattern for these materials probably will undergo changes. A major part of the electrical energy for the increased capacity was to come from thermal generation, Jamaica-was to become a major source of bauxite, and synthetic fluoride salts were replacing natural cryolite in increasing quantities. Other raw-material requirements discussed are: Soda ash; lime, and limestone; starch; filter cloth; fuel; alumina; the carbonaceous materials, green and calcined petroleum coke, high-and low-temperature pitch and coke or anthracite; cryolite; aluminum fluoride; the materials going into production of synthetic fluorides, acid-grade fluorspar, and sulfuric acid; and labor. INTRODUCTION The raw materials for the aluminum industry that have received the most publicity are bauxite, the ore that supplies elemental aluminum, and electrical energy, the means by which aluminum oxide is reduced to metal. A number of other important materials are, however, required in large quantities in the production of primary aluminum metal.

Jan 1, 1954