Search Documents

By W. M. Shaver, W. R. Dengler, F. A. Edwards

INTRODUCTION The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounzes per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required three lift hoisting for men, materials and ore. I n addition to the increased travel time and ore handling expense, increased humidity and temperature and ventilation and compressed air losses have added to the inefficiency of the operations. As a result, studies were initiated in 1980 to assess the future of the Macassa operation.

Jan 1, 1985

By W. H. Tomlinson

The fourteenth National First-Aid and Mine Rescue Contest we;; held at the State fairgrounds, Columbus, Ohio, October 2, 3, and 4, 1951. The meet, the first such event in 21 years, was under the auspices of the Bureau of Mines, United States Department of the Interior, and the Joseph A Holmes Safety Association and was sponsored by the National Coal Association, the United Mine Workers of America, and various State mine-inspection departments. The cooperating agencies that contributed to make the meet a success, in addition to the National Coal Association and the United Mine Workers of America, were the Kentucky Department of Mines and Minerals, Ohio Division of Mines, West Virginia Department of Mines, Pennsylvania Department of Mines, and the Columbus Convention Bureau. SUMMARY Fourteen teams from 6 States participated in the mine rescue contest, and 55 teams from 9 States competed in the first-aid contest. Only one of these teams entered as a combination team, that is, participating in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are listed in table 1.

Jan 1, 1953

By Ren Xiangwen, Shi Xuefa, Shao Mingjuan, Ye Jun, Yang Yaomin, Li Bing

"The Mid-Atlantic Ridge (MAR), one of the archetypes of slow spreading ocean ridges, extends from the Arctic Mid-Ocean Ridge southward to the Bouvet triple junction making up a significant proportion (~ 40%) of the global oceanic ridge system. During the past few decades, many hydrothermal fields like TAG, Logatchev, Ashasze were discovered along the northern part of the MAR, whereas the southern part, which makes up one third of the ridge (6000km), shows little documentation of hydrothermal mineralization, except for three sites: Site 4°48! the Nibelungen Field, and Lilliput. During March to May 2011, following discovery of three new hydrothermal fields during the 2nd Leg of COMRA's 22 Cruise of the R/V DayangYihao, the 3rd and 4th Legs found another two high temperature hydrothermal fields (SMAR15°S, SMAR26°S), one low temperature field, and several fields with strong turbidity and temperature anomalies in the water column. In this study, we present a preliminarily study of the mineralogy and isotopic geochemistry of the sulfides from SMAR 15°S and SMAR26°S.SMAR 15°S is situated in a SE-NW offset depression of an axial neovolcanic ridge in the median valley, with water depth of about 2793m. In the water column around this field, strong turbidity and temperature anomalies were detected. Ten-meter tall venting chimneys, hydrothermal mounds, as well as a large amount of hydrothermal vent shrimp were also observed and recorded by ROV and deep-tow camera surveys. The samples collected from this field include sulfide chimney fragments, massive sulfides and basaltic rocks. Based on the major metal and the mineral assemblages, three types of sulfides have been identified: 1) Zn-Fe rich sulfides with abundant wurtzite and pyrite zoned fragments, 2) Cu-Fe rich sulfides with much isocubanite and pyrite assemblage, 3) Fe-rich sulfide with massive pyrite fragments. These indicate that this field has undergone at least three phases of mineralization during the venting history."

Sep 1, 2014

By X. Bai

A new heuristic sublevel mining stope optimizer is presented. The optimizer seeks the best locations and lengths of a series of vertical raises that, together with the blocks linked to each raise, define a mining stope. Five design constraints ? the footwall angle, the hangingwall angle, the number of raises, the maximum distance of a block from a raise, and the minimum width required to move the farthest block towards the raise ? allow the shape of the sub-stopes associated with each raise to be controlled. The optimization is done on the locations and lengths of raises using a genetic algorithm to efficiently sample the parameters? space. For each raise, a local network is defined in cylindrical coordinates around the raise such as to impose the design constraints. A maxflow algorithm on the local network is used to determine the optimal sub-stope for each raise. All substopes are combined to define the global stope for the entire deposit. The best global stope is obtained using a genetic algorithm to find the raise parameters providing the best profit over the entire deposit. Two synthetic cases and one real deposit are used to evaluate the new algorithm and compare the results with the single-raise optimizer. The multiple raises approach leads to significantly improved economics compared with the single-raise stope optimizer, and the dilution is also substantially reduced compared to the single-raise case.

Jan 1, 2014

By J. P. H. Steele, M. U. Ozbay

As mining operations progress toward tele-mining and autonomous procedures, the need for machine performance monitoring increases. Presently, through a combination of vision, sound, and other subjective observations, an operator attempts to optimize the mechanical excavator’s operation. As the operator is moved away from the face in the case of tele-mining or completely removed for autonomous operation, the qualitative sensory input is lost. This lost information must be replaced with quantifiable sensory input. Chip formation detection may be a suitable replacement sensory input. Chip formation can be predicted with high confidence (>80%) through the analysis of the load waveform associated with the bit/rock interface.

Jan 1, 2002

By P J. Mienie

The Palaeo-Proterozoic Transvaal Supergroup in the Northern Cape Province of South Africa is host to the largest known resources of high-grade hematite ore on the Southern African continent. These ores are currently being exploited at Sishen and Beeshoek. Hematite occurances on the Sishen South exploration project (some 65 km south of Sishen mine), are at present the focus of an intensive investigation. At both the Sishen and Sishen South deposits, mineralisation is found within lithologies belonging to the Transvaal and Oliphantshoek Supergroups. The Transvaal Supergroup comprises a basal, carbonate platform sequence (the Campbell Rand Subgroup) overlain by thick units of banded iron-formation belonging to the Asbestos Hills Subgroup. The Asbestos Hills Subgroup is unconformably overlain by sedimentary rocks of the Gamagara Subgroup. The latter Subgroup has been correlated with the lowermost unit of the Oliphantshoek Supergroup. The Sishen and Sishen South deposits are located close to the western margin of the Kaapvaal craton and have been subjected to intensive, structural deformation. Both localities have undergone folding, faulting and thrusting. Early regional tectonism (2400 - 1700 Ma) played a critical role in the genesis and preservation of the ores from younger erosive events. At both deposits, four similar iron ore occurrences have been recognised. The ores have developed in specific depositional environments and hence display unique physical, chemical and metallurgical properties:The bulk of the high-grade hematite comprises laminated and massive ores, which are found in the upper parts of the Asbestos Hills Subgroup. The laminated and massive ores are best developed in basinal and pseudo-graben structures. Collapse breccia ores of medium- and lower-grade are preserved within deep palaeosinkholes. The sinkholes have developed within the dolomites of the Campbellrand Subgroup. Lower-grade conglomeratic and gritty ores constitute the remainder of the deposits. These ores are found in the overlying clastic succession of conglomerates, shales and quartzites belonging to the Gamagara Subgroup. Although, there are many stratigraphic and lithological similarities between the Sishen and Sishen South deposits, there are also important differences, which will impact on the profitable exploitation of the ores. The most striking contrast between the deposits is their size and geometry. Sishen mine is a single pit operation with an opencast mineable reserve of 895 Mt. The Sishen orebody is thicker, more continous and significantly larger than the Sishen South deposit. The Sishen South deposit has a potential opencast reserve of 228 Mt. It comprises a number of small and narrow, isolated orebodies, spread over an area of ¦64 km2 . There is a significant difference in grade between the deposits. On average the orebodies of the Sishen South deposit have a higher iron content (+0.25 per cent Fe), less potassium (- 0.090 per cent K2O) and less phosphorus (-0.019 per cent P). The Sishen South deposit has less interbedded shale in the laminated and massive ores. The footwall of these high-grade ores is a light-density, intrusive sill, compared to banded iron-formation at Sishen. With a proposed heavy-medium separation plant at Sishen South, the impact of dilution on product grades is expected to be less than that currently experienced at Sishen.

Jan 1, 2002

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By Paul C. McWilliams

This Bureau of Mines report analyzes data on the physical properties of quartzite rock from the Crescent mine, Coeur d?Alene mining district, Kellogg, Idaho, to demonstrate the use of multivariate techniques. After regression, factor, component, cluster, and discriminant analyses are discussed, these techniques are applied to the Crescent mine data. Three appendixes contain some of the required mathematical and statistical detail plus heuristic examples of three multivariate techniques --component, cluster, and discriminant analysis.

Jan 1, 1978

By Timothy P. Smirnoff, Tracy K. Lundin

INTRODUCTION The City of Phoenix, Arizona is located in the Phoenix Basin watershed which is prone to flash flooding several times each year. The runoff from these storms moves from the mountains in the north to the Salt River in the south. An extension of Interstate Highway 10 (1-10) will pass through the city east to west to form an Inner Loop through the downtown business district. PROJECT DESCRIPTION The I-10 Inner Loop extension will be a depressed roadway which would intercept the surface drainage of the Phoenix Basin and separate the watershed into two regions. To prevent flooding of the depressed roadway, runoff storm water collected from the northern half of the drainage area will be conveyed beneath the roadway to its natural outlet at the Salt River. A conveyance system composed of pressure tunnels beneath the city, shown in Figure 1, was proposed to achieve this goal . Table A presents the prominent features of each of the tunnels. This paper will describe geologic and engineering parameters specific to Phoenix which were used in the design of a series of tunnels to convey storm water from the I-10 Inner Loop to the Salt River. The design of tunnel initial and final support is described along with support and construction methods used by the Contractor.

Jan 1, 1985

The principal dirnensions of the chimney were fixed as follows: Height from formation to coping, 328 ft. 8 in.; inside diameter concrete shell, 13 ft. Gin.; inside diameter of the 4~-in. brick lining. 11 ft. (j in. ; shell thickness above flue inlet at a point 39 ft. above formation, 1 ft. 8in.; shell thickness at coping, 6 in. That is, the inside of chimney is cylindrical, wldst the outside is gradually stepped inwards with of 1 in. and less until the shell is 6 in. thick only at the top. With these dimensions in mind, it will be seen that some close thought was necessary to ensure a satisfactory of fonn which could be kept rigid and plumb to a height and at the same time provide safe working conditions for the labourers employed.FOUNDATIONSThe spread base of the chimney is 45 ft. in diameter, and foundations were carried down to a depth of 8 ft. 6 in. below natural surface into good hard clay which was known to be the best foundation obtainable in the vicinity being capable of withstanding, when dry, a load of 3 tons to 4 tons per square foot, whereas dead load is 1A tons per square foot and the maximum load expeeted under the most severe wind condition is 2 tons per square foot to ensure the foundation being kept dry and unaffected by ground water, the site was surrounded by a ring drain at a distance of six feet from edge of concrete foundation and at a minimum depth of one foot below bottom of concrete. Open-jointed pipes were laid in the bottom ofthe drain and graded to a pipe drain with outfall clear of the site.

Jan 1, 1924

By Pavel Vasak

Microseismic monitoring has become standard practice in the mining industry as a ground control monitoring tool at depth. Translating the information into practical hazard assessment tools for the rock mechanics practitioner is the focus of research jointly conducted at Creighton Mine by INCO Mines Technology Centre (MTC) and the Geomechanics Research Centre (GRC) in Sudbury, Ontario. Rock mass damage mechanisms are typically related to stress and the presence of geological structures. Due to well executed de-stress blasting practices at the mine, stress related problems are minimized. However, structurally related damage mechanisms associated with shear zones, faults and joints pose a substantial hazard. Identifying active structures from the dataset of seismic and microseismic events is generally problematic. We propose a new methodology that uses a combination of spacetime event density, hierarchical clustering and principal component analysis to identify planes of microseismic activity, termed active planes (APs). Once identified, the presence and intersection of active planes can be used to provide a hazard ranking for nearby excavations. The ranking is based on the standard Q rock mass classification system, with emphasis on the joint set number (Jn) and stress reduction factor (SRF) parameters. If the rock is treated as a fractured continuum, then, the Jn indicates the degree of freedom for blocks to move and hence, increased potential hazard. An increased hazard can also result if the APs are larger-scale and discrete (faults) rather than ubiquitous (joints). In this case the SRF is used as a measure of the degree of looseness in the rock mass.

May 1, 2004

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

During a programme to determine the suitability of the UK site for deep disposal of radioactive wastes, geostatistical methods were used to characterise rock heterogeneity on the basis of seismic and wireline acoustic-impedance data. The data were analysed to yield semi-variogram models that quantified the three-dimensional spatial heterogeneity of acoustic impedance. These models were reconciled with geological interpretations of the area and used to generate simulations of acoustic impedance, with wireline acoustic impedance as conditioning data. The three-dimensional simulated images were compared with actual seismic acoustic impedance. The variography confirmed a vertical zoning effect in the Borrowdale Volcanics, showing that it is caused by preferential clusters of high acoustic impedance values corresponding to regions of relatively low porosity. The method provided realistic three-dimensional models from sparse, one-dimensional wireline data

Jun 19, 1905

[ ]

Jan 1, 2009

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications.

Jan 1, 1963

By B. K. Belle

The use of diesel engine locomotives in South African mines can be traced to Van Dyk Consolidated Mines Ltd on the Witwatersrand gold mines in 1928 as a replacement for battery locomotives. The advantages and disadvantages were recognized in those days, and surprisingly, there are no significant additions to this list, but only refinements. In the absence of any Occupational Exposure Limit (OEL) for Diesel Particulate Matter (DPM) in SA, the Mine Safety and Health Administration (USA) rule is currently being used as a benchmark for the ventilation engineering designs. This paper discusses the ongoing SA journey of measurement and limitations of exposure data for ventilation planning and regulatory purposes. The currently accepted DPM limits are based upon the belief that they are economically and technically feasible for the mines to reach and are not necessarily health based. For SA underground platinum mines, a median TC/EC ratio of 1.8 with a range of 1.2 to 5.8 was observed. For SA coal mines, a median TC/EC ratio of 1.44 with a range of 1.25 to 2.13 was observed. While it is common practice in the USA to use the ratio of TC/EC for metal mines to be 1.3, the ratio found in local platinum mines is 2.2 and for coal mines, the ratio was 1.53 which is lower than Australian studies, i.e., 1.96. It has been shown that a need for critical analysis of TC/EC ratios exists, and possible reasons for variance must be understood before stringent adoption of overseas recommended limits for DPM. It is hoped that the findings from this paper would provide input to scientific approaches in developing appropriate conversion factors, limits for DPM and also in ensuring appropriate error factors (currently 1.14 for TC and 1.2 for EC) for compliance determination.

Jan 1, 2009

By Larry Schneider

"0 ne of the incentives that led to the development of non-electric shock tube initiation systems was the desire within the industry to improve detonator safety. And to the extent that nonelectric initiators are immune to the hazards of stray current and radio frequency energy found on normal blast sites, an advancement in safety has been accomplished. However, as a cautionary note, it is important to realize that there are still many hazards associated with any initiation system. While some of these hazards may differ from those associated with electric detonators, others are identical to those associated with any type of initiation system. For instance, contrary to what some uninformedblasters may believe, lightning remains a hazard when using nonelectric initiation as well as electric initiation."

Jan 1, 1995