Search Documents

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By Juan P. Camus

Mining is one of the oldest industrial activities. Its products are essential to modern civilization. Paradoxically, and despite a deep-rooted belief to the contrary, mining is not a lucrative industry— at least not in the aggregate. This assertion is true not only for recent years, one of the weakest periods in terms of metal prices, but also for a long time past. In 1776,Adam Smith said in The Wealth of Nations: “Of all those expensive and uncertain projects, how-ever, which bring bankruptcy upon the greater part of the people who engage in them, there is none perhaps more perfectly ruinous than the search after ... mines. It is perhaps the most disadvantageous lottery in the world... Projects of mining, instead of replacing the capital employed in them, ... commonly absorb both capital and profits.”

Jan 1, 2002

By Juan Lucero

Como consecuencia de los factores externos e internos, las empresas mineras necesitan ser más eficaces a través de la implementación de nuevas tecnologías e informática. En este sentido, la compañía minera Milpo disminuye los costos de hardware para así generar un control de operaciones más minucioso, automatizado y oportuno. Los principales logros obtenidos son el control detallado de las operaciones, los sistemas operativos son la base para obtener los costos operativos, una mejor formulación y control presupuestal, control de servicios de terceros y el de los sistemas integrados.

Sep 13, 2001

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

By Y. P. Chugh, J. Ma

Higher production, better safety standard, and potential for automation are some of the benefits of longwall mining. Today, longwall face advances at a faster rate exposing many diversified rock layers in a short period of time. It is now a serious challenge to cope with ground control problems such as roof falls, face and floor failure, and excessive shield loading as fast as possible to minimize production and monetary losses. In Illinois coal mines, the existence of weak floor strata blow the coal seam may pose additional problems related to floor heaving, shield base punching, and associated roof and face falls. In this study, the effects of weak floor on longwall ground control are analyzed using two-dimensional finite element models. A two-leg 635.6-ton (700-short-ton) yielding capacity shield is included in the models to evaluate the effects of different thickness and material properties of the weak floor. The study indicates that the thickness and material properties of weak floor have significant effects on shield loading, the distribution and intensity of front abutment stress, failure zones in the surrounding strata, roof-to-floor convergence, and floor punching by the shield base.

Jan 1, 2000

By Barun Gorain, Andy Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimisation of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimisation, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterise cell hydrodynamics, gas dispersion properties, fioth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimisation of the Red Dog flotation circuit.INTRODUCTIONThe traditional methodology for flotation scale-up and plant design is based on the rule-of-thumb with safety factors, dimensionless hydrodynamic group similitude considerations, etc. With the recent trend towards larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-of-thumb and trial-and-error, then the probability of failure would increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimisation of the circuit to meet its metallurgical target. This results in a plant design incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2002

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By M Carr, K Williams, W Chen, J Plinke

The depletion of iron ore deposits at the face of the mine site dictates the necessity for the exploitation of formerly less attractive orebodies to meet the demand of the modern world. These orebodies will typically be found close to or even beneath the water table where an increasing clay and moisture content will result. Problematic iron ores, colloquially termed as ‘wet and sticky’ material (WSM), can have a significant impact in the material handling stream due to the expensive downtime of processing equipment, which is attributed to the inter-particle and boundary cohesion and adhesion forces of the bulk material.In order to gain a better understanding of the causes of poor handleability, experimental test methods to determine wall adhesion, and inter-particle adhesion within bulk materials were developed. Based on the combination of wall adhesion and inter-particle adhesion measurements, with traditional methods of assessing bulk material handleability, a new method to assess the potential of bulk materials to cause handling problems is proposed. This method reduces the multitude of factors leading to problematic behaviour to a handleability index (HI) [0,1], which is easily assessed and understood. The method is suitable for adhesive materials and applicable for a wide range of material flow, from gravity reclaim stockpiles to transfer chutes and carry back on conveyor belts.Additionally, this research presents an assessment of the HI derived by experimental testing of three iron ore samples. A clear understanding of the problematic behaviour of the iron ore samples is achieved with the use of dust extinction moisture (DEM) tests, which indicates the regions where problematic behaviour may be experienced on-site.CITATION:Carr, M, Plinke, J, Williams, K, Roberts, A and Chen, W, 2017. Determination of the handleability index of adhesive bulk materials, in Proceedings Iron Ore 2017, pp 503–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Willard L. Hunter

The research described in this Bureau of Minus report was conducted to improve the chromium-iron ratio of offgrade chromite. Two methods were used: (1) Iron was selectively reduced from chromite by carbothermic reduction in an electric-arc furnace, and (2) a mixture of carbon, chromite, and sometimes fluorspar was chlorinated to remove a substantial part of the iron. Chromite concentrate from the Mouat deposit in Montana and from northern California was used in the test work. Chromium-bearing slag and chromite that had been beneficiated by a roast-leach process were each smelted to produce high-carbon ferrochromium. Iron was selectively reduced in a laboratory-scale., electric-arc furnace. Carbon additions to the smelting charges varied from 40 to 100 percent of the stoichiometric requirement, and slag basicities were varied from 0.4 to 1.0 chromium-iron ratios of more than 4:1 were obtained with 89 percent recovery of chromium in a chromium-bearing slag.

Jan 1, 1962

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

This paper discusses the application of a computerised model based on genetic algorithms (GAs), called GenRel, for reliability assessment of underground mine hoisting systems. The purpose of this paper is to investigate whether GenRel can be applied to predict future failure data of a mine hoisting system based on historical records of failures. The incentive of selecting the GAs for prediction of failures is that GAs are a class of evolutionary algorithms which imitate the biological evolution procedures such as reproduction, selection, crossover and mutation. The reliability of mining equipment changes over time due to an array of factors (eg equipment age, the operating environment, number and quality of repair). These factors affect the equipment's failure patterns and have complex impacts on the equipment's reliability characteristics. The failure patterns are assumed to follow a biological evolution process, and thus GAs can be considered applicable in the modelling process.To conduct the reliability assessment, a study was carried out with historical failure data of hoists in the time period from January to December 2007. Two failure data sets of two mine hoisting systems were collected from two typical underground mines in Ontario, Canada, which are denoted as the NA mine and the SB mine. The failure data sets were prepared in the format of time between failures (TBF). Then, these data sets were entered in GenRel to generate predicted failure data sets for the period of January to March 2008. The paper discusses the statistical similarity of the actual failure data sets for the period of January to March 2008 with the predicted failure data set generated by GenRel in the same time period.

Dec 6, 2010

Study on a Novel Polymer/Bentonite Compound Adsorbent for Removal of Cu(II) from Aqueous Solution

Sep 13, 2010

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By Graham Davey

"Ultrafine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The recent development of industrially proven and cost efficient technologies for ultrafine grinding has opened up another processing option for the treatment of finegrained metalliferous and refractory gold ores. The current commercial designs are variations of stirred mills used in the industrial minerals sector for the past 30 years. For the purposes of this paper ultrafine grinding is considered to be P80 of less than 15 microns.Attrition milling to fine grind sizes presents some challenging issues relating to scale-up including the dearth of information on the quantitative impact of feed and operating conditions, as well as the precise and accurate measurement of particle size distributions. Two examples from recent installations will be analyzed including Thalanga Copper and Century Zinc Mines. Both have diverse grind size targets for the SMD, yet both have realized significant metallurgical gains."

Jan 1, 2002

By Stefan K. Schwank

The paper describes the two foundation techniques - mini piles and postgrouted bored piles. The mini pile system is presented with its design and installation parameters, especially the drilling technique. Two case histories demonstrate the application under extremely limited space and traffic conditions and the required modifications of the equipment. After the description of the postgrouted bored piles and its grouting technique, the paper gives a comparison of postgrouted piles and standard piles on a large basic test in Germany. The Brooklyn Queen's Expressway, N.Y., case history shows the application of this technique after redesign of the original proposal. 1. General Increasing requirements to improve existing foundations to carry additional loads and to increase the bearing capacity of bored piles leads to two new piling techniques: the mini-pile and the post grouted bored pile.

Jan 1, 1991

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968

Copper ores are widespread through the Lachlan Geosyncline in New South Wales, but the size of the orebodies is generally small. The largest deposits occur in the Cobar district where an iron-rich copper ore type has been developed in Silurian sediments. Similar de- . posits to the south in the Nymagee-Mt. Hope-Melrose districts are related to quartz feldspar porphyries of probable Upper Silurian age. Deposits to the east in the Tottenham-Girilambone districts are less complex mineralogically and are possibly related to an ultra-basic source.Copper mineralization in the Highlands further to the east is often developed in Ordovician andesite or MiddleUpper Silurian acid volcanic sequences. The deposits in andesite contain considerably less galena than those in the acid extrusives; a small proportion of the mineralization in the latter has texture, mineralogy, and geologic setting analogous to the Captain's Flat copper-Iead-zinc deposit, for which both syngenetic and epigenetic origins have been proposed. Very little copper mineralization occurs within granitic material, even though rocks of this type ranging from Silurian to Carboniferous in age crop out through much of the geosyncline, and the extent of the metal contribution from plutons to the deposits in volcanics is open to question. Numerous deposits are known in the contact zone around Mid-Devonian and Mid-Carboniferous granites, however, and the formation of these orebodies has undoubtedly been influenced by plutonic activity. Small occurrences of copper with associated minor nickel sulphides are developed in a narrow serpentinite belt of possible Lower-Middle Devonian age in the southern section of the Highlands.

Jan 1, 1970

By David E. Thompson, Andrew F. McKown, Herbert H. Einstein, Amr S. Azzouz

INTRODUCTION Design of supports for underground chambers in rock has undergone considerable development. This becomes evident when comparing support dimensions of subway station caverns built in the U.S. over the past fifteen years. The Porter Square Station cavern, which is a part of the Massachusetts Bay Transportation Authority (MBTA) Red Line extension, is the latest in this series. It is approximately 168 m (550 ft) long, 21 m (70 ft) wide, and 14 m (45 ft) high, and has a permanent support of light steel ribs imbedded in a 0.4 m nominal (15 in) shotcrete lining. An extensive construction control instrumentation program made it possible to evaluate the performance of the cavern and its support. This evaluation, which is presented in this paper, was the objective of a research project sponsored by the Urban Mass Transportation Administration (UMTA) and jointly conducted by Haley and Aldrich, and MIT. The actually used design procedure was compared with other approaches, notably procedures based on Finite Element analyses and empirical rock mass classification methods. Support dimensions predicted with all these approaches were compared to the actual support and its performance.

Jan 1, 1983

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949