Search Documents

Choosing the correct delay time for many blasting applications is an important and critical blast design parameter for controlling fragmentation, muckpile shape, swell, digability, throw, ground vibration and airblast. BAl and its affiliates have monitored thousands of full scale blasts in a variety of field conditions, spanning over 15 countries, with sophisticated blast monitoring instrumentation. In some blast environments, a small change in the choice of delay times used had a dramatic and pronounced effect on the overall blast results. In other blast environments, large changes in the choice of delays used had absolutely no effect on the final results in terms of specific outputs. In environments which were sensitive to the delay selection, the type of explosive, dynamic response time of the rock mass (TMIN), integrity of the material, burden and rock mass geometry, all played a very important ,role.

Jan 1, 1998

THE nature of the ore deposit of the Broken Hill line of lode is such that it can be broadly divided into two the calcitic and siliceous ore bodies. The principal minerals occurring in these ores are: Galena, sphalerite, pyrite, arsenopyrite, chalcopyrite, pyrrhotite, calcite, rhodonite, garnets, feldspar, fluospar, quartz.Whilst these minerals persist in both classes of ore, the following typical analyses of Broken Hill South Limited ore bodies will give some indication of the disposition with regard to each:

Jan 1, 1928

By James R. Hein

Rodriguez Seamount, located 150 km off the central California coast at the base of the continental slope, was studied using the ROV Tiburon aboard MBARI?s R/V Western Flyer, October 13-16, 2003. Fe-Mn crust and rock samples were collected along the SW flank of the seamount at water depths from 700 to 2100 m; bottom-water dissolved oxygen content (O2) and temperature were determined at each sample site. Fifty-three samples of bulk crusts, crust layers, and surface scrapes (~0.5 mm) were analyzed for 59 elements. Data allow for the correlation of crust compositions with precisely known water depths and seawater O2 measured at the actual site of sample collection. This is the first detailed study of Fe-Mn crust compositions in a region of strong continental-margin upwelling. Compared to open-ocean seamount Fe-Mn crusts, Rodriguez crusts have significantly higher (2-6 fold) mean concentrations of Fe (26.9%), Al (1.65%), Si (13.0%), Cr (82 ppm), Th (64 ppm), and Ag (1.7 ppm); and significantly lower (2-8 fold) mean concentrations of Ca, P, Bi, Co, Cu, Ni, Tl, and especially Te (8.2 times lower). All but one Fe/Mn ratio are >1 compared to <1 ratios for open-ocean crusts. O2 contents (0.35-2.03 ml/L) are nearly perfectly corrected with water depth and elements correlated with one are correlated with the other. The Fe-Mn surface scrapes represent 60-450 ka (mean 150 ka) of growth, whereas the dissolved oxygen contents of seawater represent an instant in time. Assuming that the entire sample set was affected uniformly by oceanographic changes, we suggest that correlation of elements with O2 may reflect oceanographic processes. O2 has a negative correlation with P, V, As, Fe, U, Be, Pb, Cr, Mg, Y, Bi, Te, and REEs (except Ce) and a positive correlation with aluminosilicate-hosted elements (Al, K, Rb, Cs). This later relationship is related solely to water depth, indicating that detritus shed down the seamount slopes accumulates in greater abundances in deeper-water crusts. Si/Al ratios indicate that the detritus includes a large component of biosilica produced by upwelling-mediated high productivity. These observations are supported by positive correlations of aluminosilicate-hosted elements with crust growth rates (range 1.2-13.0 mm/Myr). In contrast, other elements (Sr, Co, Mn, Mg, Te, As, Mo, V, W, U, Ti, Ni, REEs, etc.) are negatively correlated with growth rates. Growth rate has a weak positive correlation with O2. These compositional characteristics indicate that even though low-O2 seawater acts as a reservoir for Mn and associated elements and produces slow growth rates, which would allow for the concentration of elements and surface oxidation processes to occur, the high rate of input of detritus and high bioproductivity ameliorate the strong concentration of most metals. This dilution is significantly enhanced by the doubling of FeOOH in the crusts--the main cause of the generally high growth rates compared to open-ocean crusts. The high growth rates limit the oxidation of Co, Tl, and especially Te on the crust surface, which is reflected by their relatively low concentrations. Within the range of oxygen contents measured, O2 has less of an influence on crust chemistry than does the availability and incorporation of FeOOH and detritus.

Jan 1, 2004

By Philip C. Good

Red mud residue from Bayer process treatment of Jamaican bauxite was dewatered in batch and in continuous centrifuges. Solids content of the residue was increased from its original value of 20 to 25 percent to about 40 percent by centrifuging. Clear effluent amounting to approximately 40 percent of the slurry liquid was recovered containing dissolved alumina and soda values for potential recycle to the alumina plant" Addition of a chemical flocculant to the centrifuge increased capacity by about 35 percent. Manufacturer&apos;s estimate of large-scale equipment requirements, based on data collected in this investigation, was that a proposed installation for dewatering 16,000 tons per day of Jamaican red mud would require twenty-two 24-by 60-inch solid-bowl-type centrifuges. Cost analysis of a proposed installation, based on a Jamaican red mud tonnage of 16,000 per day, is included also.

Jan 1, 1968

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was clone through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will he useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetimes. This report is in two volumes: Volume l - Technical Report Volume 2 - Design, Inspection, and Maintenance Manual

Jan 1, 1977

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010

By D Craw

Bulk ore tailings from the Macraes gold mine gold extraction process are stored in a large (ca 0.6 km2, 80 m deep) mixed tailings impoundment whose pH is maintained near 8 by natural rock neutralizing capacity. The mixed tailings will be stored in this impoundment in perpetuity after mining ceases. Confidence in the long term environmental stability of these tailings can be gained from examination of mineralogically and chemically similar geological situations in the immediate vicinity. A sequence, typically about 5 m thick, of sands and gravels derived from the Macraes mineralized zone 12 000 to 28 000 years ago contains rounded detrital sulphide mineral grains which are unoxidized despite close proximity to the surface and occasional incursion of oxygenated waters. Saturating water pH is currently 7-8. Sands with 0.2 to 0.8 wt % organic carbon host sulphate-reducing bacteria (SRB), and localized cementation by authigenic framboidal pyrite has occurred. Comparison of the 28 000 year-old sediments with the modem tailings suggests that similar chemistry will prevail, possibly with deposition of authigenic pyrite in the tailings, in the long term. As long as the present slightly anoxic and circumneutral pH environmental conditions are maintained in the mixed tailings dam, sulphide decomposition and acidification are unlikely. These sediments provide a plausible geological analogue for long-term benign storage of the mixed tailings impoundment.

Jan 1, 2000

This study was conducted to determine the feasibility of using large tractor dozers in land reclamation of strip-mined areas. The procedures used are patterned after engineering models developed for evaluation of military ground vehicles in cross-country operations. Tractor dozer manufacturers furnished information on capabilities of existing equipment and ideas on the practicability of using dozers larger than those currently available Generally, they believe that current dozers in the 500? to 700-horsepower range are about as large as can be built and remain economically feasible. However, one manufacturer has a wheeled dozer rated at 1200 horsepower, and another is testing a tracked dozer of about the same horse-power.

Jan 1, 1975

By Whiten W. J

A simulation model was used to study the performance of various types of screen cloth on industrial vibrating screens. The model takes into account the effect of loading upon screen performance and predicts both themass flow rate and size distribution of the screen products.It was found that the use of the simulation model allowed the reconstruction of data for identical conditions and hence has simplified the analysis of the comparative performance of the screens. The dependence of performance upon operating conditions was found to vary markedly with screen cloth type.

Jan 1, 1977

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By S. Kelebek, J. A. Finch, Zhenghe Xu, S. R. (Ram) Rao

To improve SO2 emission compliance, pyrrhotite from Sudbury copper-nickel ores is being depressed with DETA. To understand the mechanism of depression, the role of complexing in controlling metal-ion activation of pyrrhotite was investigated. DETA was found to remove Cu and Ni ions but leave hydrophilic ferric species on the pyrrhotite surface. The metal:DETA ratio appeared to be 1:2. Cu was more readily removed than Ni, but the combination of DETA with sulphur dioxide was equally effective for both metal ions. Certain combinations of DETA, Ni ions, xanthate and dithionite (S2O4) or dithionate (S2O6), as representative derivatives of SO2 in water, produced hydrophilic precipitates. These may enhance pyrrhotite depression

Jun 19, 1905

By Erich J. Jacob

In the past 15 years the enforced improvement of the public traffic systems caused a boom in urban tunnel construction. In 1961 the City of Paris started to build the Express-Metro. Of the 47 km long double-track line crossing the city center, nearly 45 km are in operation since 1971. Still missing is here only an about 2.6 km long connecting stretch, which is under construction now. From 1963 to 1969 the 21.8 km long Victoria Line was built in London as extension of the existing network,. A little later, in the years 1965 to 1973, the City of Hamburg supplemented its subway network by the construction of a 16.8 km long line between the Boroughs of Billstedt and Stellingen. Also in 1965 the City o Munich started to build a subway system of 54 km f length. Thereof a stretch of 16.2 km could be taken into operation in 1972 shortly before the Olympic Games. These are only some of the better known projectsas examples of the activities in European cities. In nearly all cities with more than about ½ million inhabitants subsurface traffic lines were begun or supplemented. Furthermore, numerous undercuts or other subsurface structures were built. The Ij Tunnel in Amsterdam and the new Elbe Tunnel in Hamburg may be mentioned, both structures finding international attention.

Jan 1, 1976

By H. -J. Langhoff

"The paper describes not a result, but a starting point to implement sustainable development to a region characterized by a typical down river landscape, agriculture, and extractive industry. The NaturFreizeitNiederrhein GmbH (NFN) is a private company with associates from administrative bodies, the local mining companies and multiple representatives of environmental protection groups (local and national), tourism organizations, cultural societies and also aquatic sport and fishing clubs. Center of the concept is the "NFN Lake District." The development concept aims to provide the agricultural industry with alternative means of income, while protecting wildlife and the ecological balance as well as preserving the social und cultural system and enhance the safety against flooding from the river Rhine. The mining industry contributes their coordination of obligation concerning reclamation and recultivation of the already existing individual projects. While designing the landscape components and establishing the infrastructure for the different tasks, the production of gravel and sand is yield as a by product. The result is a long term perspective for region and industry."

Jan 1, 2005

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) The system design of hydrostatic drives for mine hoists, usually of special nature, is considered along with oil hydraulic component selection suitable for the application; (b) The criteria for head frames of steel and/or concrete are developed with full consideration of all operating and environmental conditions.

Jan 1, 1988

By George A. Morgan

There was little change in the mineral industry of Benin in 1986, as the economy remained in the grip of a regional recession exacerbated by failing oil prices, which nullified much of the income from Benin&apos;s oil production. Benin&apos;s industrial sector accounted for less than 10% of the gross domestic product (GDP), with the mineral industry providing about one-half of that total. Several major projects initiated over the last several years continued to perform and/or progress below Government expectations. These included the Save sugar refinery, the Dassa-Parakou section of the Dassa-Cotonou highway, the Benin-Togo Nangbeto hydroelectric plant, the Onigbolo cement plant, and the Semé Oilfield. Funding for these projects is the major source of the Beninese external debt, which was estimated to be over $800 million.2

Jan 1, 1988

By José Cayetano

El presente trabajo plantea un proceso para minimizar el contenido de bismuto en las celdas de electrorefinación, a través de la adición de carbonato de bario a la solución electrolito, de forma que el bismuto soluble presente en fase líquida, se precipite sobre la superficie del precipitado insoluble de BaSO4, bajo una coprecipitación por adsorción e intercambio debido al equilibrio dinámico entre el precipitado y la solución de electrolito conteniendo al bismuto. En este sentido, se reduce la presencia del bismuto en el electrolito de cobre en un 75%, adicionalmente se tiene la disminución del contenido de plomo en un 96%, de estaño en 48% y de plata en un 18% aproximadamente.

Oct 21, 2015

Analyses of scheelite from all the known scheelite fields in the South Island of New Zealand have shown that the scheelites are essentially molybdenum-free. The scheelites are almost stoichiometric CaWO4, except for some strontium replacing the calcium, with a maximum of 0&#183;92 per cent SrO. Variation in strontium content appears to be&apos; related to the metamorphic grade of the enclosing rocks.

Jan 1, 1970

Amongst the unavoidable studies of the mining engineer who desires to reach the maximum efficiency, is the subject of patents. With the fundamental principles of the patent laws of this and other leading countries he should of course befamiliar, but still more should he keep abreast of that practical knowledge which will enable him to act or advise wisely when the patenting of a new invention, or the sale, purchasing, or adoption of a new patented machine or process becomes amatter for consideration. As every engineer worthy of the name is an inventor and more particularly every mining engineer he has a direct interest in watching the progress of legislation and administration concerning patent monopolies.His worldly prospects may indeed, to a considerable extent, depend upon the defeat of bad patent laws and the removal of incompetent officials, or the appointment of better ones. Better patent administration is always in Australia a valid requirement, and until engineers generally take up and press the demand, bad administration is likely to continue. Even though every engineer is not a patentee, nevertheless his interests in patents must always be direct and powerful, and ignorance or apathy in regard thereto must inevitably injure either his own interests or those of his employer. When we consider the tens of thousands of mines scattered through Australia alone, on everyone of which there is expensivepatented machinery, and when we consider the thousands of...

Jan 1, 1901

By N Cusworth

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines û mining, metallurgical, chemical, civil, electrical, mechanical and environmental û as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies û and hence no two development projects û are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource projectÆs development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as ædoing a feasibility studyÆ. But the principal purpose of a æfeasibility studyÆ is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant û they are a prerequisite to the demonstration of a projectÆs viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of æfeasibility studiesÆ and provide guidance to minimum standards and best practice.

Jan 1, 2007