Search Documents

By Alun J. Davies

This paper describes a design-build project for the construction of a tanker wharf for 150,000 dwt vessels. The tankers deliver oil from offshore oil fields to a Transshipment terminal on the south coast of Newfoundland. The project described is an expansion to a previously constructed facility, adding an additional berth. The first berth was designed conventionally as concrete structures supported on groups of independent, single piles. The second berth was awarded to Peter Kiewit Sons' Co. Ltd. based on an alternate design which utilized a "jacket" concept whereby prefabricated steel frames are placed on the seabed and serve as permanent templates and also give lateral support to the piles, thereby increasing their load capacity. This led to economies and time savings. Discussed herein is the design process and the field installation, covering the jackets, driven pipe piles, and the rock anchors.

Jan 1, 2000

By Mazin Adnan

The 80m high dam at the Peribonka river in the Canadian province of Quebec was designed for the generation of 385 MW of hydro electrical power (Fig.1). The complex ground conditions required the employment of a variety of geotechnical construction methods stretched to limits never experienced before. Innovative grouting and trenching techniques were used for the construction of a plastic concrete cut-off wall down to a depth of about 116m, to cut hydraulic seepage through alluvial deposits forming the dam foundation. The bedrock where the cut-off wall is embedded forms a glacial gully with steeply sloped flanks, which created further challenging conditions. [ ]

Jan 1, 2008

By G. H. Wigton

This paper, describing the concentrator practice of the Chief Consolidated Co., is one of a series being prepared by the United States Bureau of Mines. The concentrator adjoins the town of Eureka, Utah, in the Tintic mining district. The Chief Consolidated, Eureka Lilly, Plutus, and Grand Central mines, all of which are owned or controlled by the Chief Consolidated Mining Co., are the principal sources of milling ore. The ore is transported from mines to mill by railroad. Although all the mines are within 3 miles of the mill, the railroad distance varies from 1 mile to 12 miles.

Jan 1, 1930

By Hans von Michaelis

"INTRODUCTIONThe renaissance in gold and silver recovery technology has continued to unfold and it is appropriate to review some of the useful new technologies as well as try to identify some of the industry's future needs and frontiers.The remarkable strengthening in the US dollar has resulted in a relatively low gold price in US Dollars of around $310/oz at the time of writing and silver at $6.25/oz. This general softening in the dollar prices and the recent confusion as to environmental compatibility of cyanidation tailings and effluents, has led to a slowdown in announcements of new operations. Another reason for the slackening off in the USA is that in the past few years a large part of the capital has come from oi I and gas companies that now seem to be losing interest in mineral ventures, and foreign investors for whom the dollar is becoming out of reach. In the author's opinion this represents an unprecedented window of opportunity.Elsewhere in the world where local currencies have weakened, the price of gold is at or close to its all time high.For example, in South African Rands, the gold price was R571.00/oz when the rand was US$1.47 and the gold price reached US$800. Now at US $309/oz and with the Rand at US$0.51 = Rl .00, the local gold price is R600. The price of si Iver in Mexican pesos is not much less than it was when silver reached US$50/oz. Gold, and silver prices in local currencies outside North America are still buovant and at levels where additional investment in new projects is more encouraging.Even in Canada where the dollar is worth about US$0. 75, this provides a smaller but significant cushion compared with US operations. Considering the present strength of the US dollar and even the Canadian dollar relative to many other gold producing countries, there should be significant investment opportunities at today's prices. Mining companies have started to descend on Brazil, for example, where in a matter of just a few years annual gold production has increased from 10 to 70 tons. In South Africa, a Canadian company backed by Swiss financing has been able to take over a Witwatersrand gold mining operation and is installing a huge new tailin9s retreatment plant to process about 1 million tons per month of tailings."

Jan 1, 1985

By Sunil Koppalkar, A. R. Laplante

"A Pilot Plant was installed in one of the grinding circuits of the Dome Mill, Ontario, Canada. Tests were conducted on a KCCD12 Knelson Concentrator to systematically analyze the effect of operating variables on the performance. The main objective of this test work was to explore the effect of very coarse (6 mm) feed size on GRG recovery and performance of the Knelson concentrator. Preliminary results have shown that coarse feed size is deleterious to maximizing recovery. Size-by-size GRG recoveries have shown an unusual trend in the sense that recoveries do not decrease monotonically with decreasing gold particle size. Similar trend observed in one other full-scale unit has been compared. The observed trend is probably linked to the feed size distribution and top size.INTRODUCTIONKnelson Concentrators are the most widely used semi-continues centrifuge gravity separation units for the recovery of gold and platinum group minerals (Xiao and Laplante 2004). The main advantages over the competing centrifugal gravity units are their design, operating simplicity and good separation efficiency that make them the most common choice for gravity circuit. Despite some characterization at bench scale and a limited characterization at full scale, there is a lack of a comprehensive study of impact of operating variables on efficiency that reflects realistic full scale operating practice. GRG characterization studies, at bench scale, on these units provide information about the occurrence of gold in ore samples but fail to provide adequate information about the effect of operating variables for full-scale units. It is well known fact that such work is difficult to undertake on full-scale units owing to the difficulties involved in sampling and systematic variation of operating parameters. To tackle these problems, a pilot facility consisting of a 12-in CD Knelson Concentrator, a feed screen and tailing pump was installed in one of the grinding circuits of Dome Mill. This paper describes the work carried out and the results.Porcupine Joint Venture (PJV)Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. The JV utilizes the milling capacity of the Dome Mill to process ore from Placer Dome and Kinross mines. The Dome Mill circuit has gravity concentration, cyanidation and CIP circuits to recover gold. Gravity recovery has been used at Dome Mill since inception to recover gold: first by using conventional jigs, which were eventually replaced by two Knelson Concentrators in 1993, one in each of the grinding circuits. Three more Knelsons joined the circuit in 2002 to improve gravity recovery. An Acacia Intensive Leach Reactor was also added in 2002 to process gold concentrates replacing shaking tables (Chong et al 2004)."

Jan 1, 2007

By James J. Kabat, James A. McDonald

Impregilo/SA Healy JV recently completed this Project using the first slurry shield TBM’s in the United States. The Project used two TBM’s to mine 18,000 feet in sands, gravels, and silty alluvial materials under the Willamette River and downtown Portland, Oregon. This paper discusses alignment and geological conditions, equipment selection and plant setup, and tunnel excavation means and methods, parameters, and results. Extensive hyperbaric operations were required and will also be discussed.

Jan 1, 2007

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

The recovery by flotation of some complex uranium minerals such as brannerite and davidite is described. Anionic reagents used for flotation of iron and titanium oxides' are suitable. If care is taken, to emulsify the reagents the slime fractions may be satisfactorilytreated.INTRODUCTIONUranium ores are usually treated by direct leaching with acid or alkali according to the nature of the gangue materials. Concentration of the uranium minerals prior to leaching is not commonly practised because of the earthy nature of most uranium minerals and the difficult mineral dressing problem they pose. Some of the harder complex oxides such as davidite and brannerite are amenable to flotation. This is fortunate since they usually require an expensive, strong acid treat~ent to dissolve the uranium. Flotation tests were commenced in 1949 by officers of the South Australian Department of Mines stationed at Adelaide, first in the School of Mines, then in the University of Adelaide and finally in Departmental mineral dressing laboratories at Thebarton. Separation of daviditefrom Radium Hill and Mount Victoria ores, brannerite from Crocker's Well ore, and secondary uranium minerals from Myponga ore was attempted.The development of the flotation reagents to separate the oxides from silica and the silicates is first described, then some of the results obtained are presented as tables.DEVELOPMENT OF FLOTATION REAGENTSThe davidite at Radium Hill is associated with iron and titanium oxides, qu;a,rtz and biotite as replacement deposits in shears. The davidite, rutile,' ilmenite and hematite usually occur in segregations from nut size to masses of several pounds. They are associated as a complexity of...

Jan 1, 1955

By Laxman S. Sundae

A Bureau of Mines investigation was conducted to determine the effect of specimen volume on the apparent tensile strength of disks of St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite. The investigation used a technique developed by the Bureau to determine apparent tensile strength. Because the test specimens were selected without macroscopic defects, that is, cracks, joints, and planes of weakness, the strength variations are solely due to microscopic features. Several replications of each test were performed. Data for each set of specimens were fitted to a power law of the form y = axb, where y = apparent tensile strength, x = specimen volume, and a and b are constants. This power law is essentially a form of Weibull's theory. The average coefficients of correlation for St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite were 0.85, 0.53, and 0.78, respecitvely. In all cases a decrease in strength with increasing volume was noted; in the extreme case, a decrease of 40 pct was noted with an elevenfold increase in volume. The decrease in strength with increasing specimen volume is explained in terms of Weibull's theory.

Jan 1, 1974

Jan 1, 1929

By Chris Breeds, Larry Leone, Jerry Wallace

Project Owners typically require General and Detailed Blast Plans when blasting close to important structures and specify the maximum allowable peak particle velocity for each potentially affected structure. Low, residential level PPV limits may be specified which significantly restricts the potential for blasting to be effectively used. Contractor’s responding to these contract conditions typically cite historic case studies which may, or may not, apply to the specific situation and/or types of structures for which limits have been set. A long submittal cycle typically follows.

Jan 1, 2010

By Wynand Erasmus, Terry A. Jones

The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals. The KCJ has been successfully employed in mineral sands applications in Australia for approximately 12 years. More recently, the KCJ has been tested and installed on zircon tailings dump retreatment projects in Australia and the USA, while being considered for similar projects in RSA, and is about to be installed in zircon tailings processing duties in India and Africa and in a tin removal duty in a rutile circuit in Australia. Extensive test work has been carried out on these applications and some typical performance data is presented in this paper. Information is also provided on the principles of operation of the KCJ and on the keys to a successful KCJ installation.

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.' The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

By Creelman C. A

With the technique and data obtained in using the blast hole diamond drill for "Removal of Horizontal Level Pillar by means of Blast Hole diamond drilling at New Occidental Gold Mines N.L.," as described in Proceedings No. 133 of 1944, and a series of experiments using the blast hole diamond drill for stoping at New Occidental and New Cobar Mines over the past two years, a benching method of stoping has been developed using 2 inch coring diamond drill bits, resulting in efficient and economical ore extraction in these large ore bodies.During the experimental stages the standard H-inch blast hole was used, but the deflection of the holes, when using this solid bit, either decreased or increased the burden of the hole when it became necessary to drill holes deeper than 45 feet.It was found that after blasting vertical holes deeper than 45 feet, the ore did not break satisfactorily over the full length of the hole; on one occasion as much as 30 feet of bench was left at the bottom of the face, which had to be subsequently re-bored andblasted.As this defect was also noticeable to some extent even when the holes did not deflect, it was then obvious that the explosive had become less sensitive in the lower section of the hole. This was probably brought about by pressure being built up ahead of the detonation wave in H-inch hole, resulting in desensitization of the explosive.Another series of experiments were carried out, using 2-inch solid bits, which enabled a much greater burden on the holes, and the use of primacord for the full length of the hole.This gave satisfactory results regarding breaking and fragmentation, but was uneconomic owing to the excessive consumption of diamonds, and the slow rate of drilling.Further experiments were then carried out using 2-inch coring bits, (Fig. 1) which allowed holes of 90-feet to be bored with little deflection, and proved to be entirely satisfactory as to cost and speed of drilling.

Jan 1, 1945

By R. V. Higgins, G. B. Shea

"FOREWORDIn the second year of World War II, the petroleum industry in California was taxed to near capacity to satisfy the expanded war demand for petroleum products, particularly fuel oil. With discoveries of crude oil in California declining and known reserves being depleted rapidly, conditions appeared to warrant study of the possibilities of utilizing the outcropping bituminous sandstone deposits in California for obtaining new sources of oil if the war should he prolonged. At conferences in Washington, D. C., with members of the Petroleum Administration for War and the Geological Survey, Bureau of Mines engineers emphasized the importance of determining the extent of those outcropping deposits of oil-impregnated rocks and of developing a practical process for commercial recovery of the contained bitumen to assure, if necessary, a supplementary supply of fuels. The desirability of such a study was recognized, and in July 1943 the Petroleum Field Office of the Bureau of Mines at San Francisco, Calif., in cooperation with the Geological Survey and the Petroleum Administration for War, initiated a study of the bituminouss sandstone problem. It was agreed that all mapping and geological work in connection with the study would be done by the Geological Survey, all engineering studies in developing a process for extracting the oil would be carried out, by the Bureau of Mines, and that the Petroleum Administration for War would aid in final adoption of the results in the field if circumstances warranted such action.Deposits of bituminous sandstones in California occur principally in the immediate region of the Coast Range mountains, notably at Pt. Arena, in Mendocino County, about 110 miles north of San Francisco; near Santa Cruz, in Santa Cruz County; in the Edna area in San Luis Obispo County; in the Sisquoc area in Santa Barbara County; and in the Ojai and Santa Clara Valleys in Ventura County. 4/ In addition oil-bearing sands outcrop near McKittrick and Maricopa, in western Kern County, and along the east edge of the Kern River oil field. Among the several prominent deposits of these source materials, those occurring near the cities of Santa Cruz and San Luis Obispo, and the town of Sisquoc are the largess."

Oct 1, 1948

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By R. S. McDonald

Auburn began operations 40 years ago with an office in Sudbury, Ontario, Canada, to provide services to Inco Limited. Over the next 40 years, operations expanded considerably, with projects being undertaken around the world, servicing the smelting and refining industry. Operating bases have been established in Canada, United States, Mexico, Chile, and Spain, with further growth expected to continue with an operating presence in South Africa. The Auburn Group of companies has serviced the smelting and refining industry for over 35 years. Auburn services a variety of metallurgical plants, and our worldwide experience has gathered considerable knowledge on industry processes and maintenance solutions. Today, the ?Business of Smelting? tackles demanding challenges, and operators search for opportunities and solutions to improve smelter maintenance, reduce operating costs, and decrease downtime. The Auburn Group has developed project teams, technologies, and equipment that provide specialised and innovative solutions to the non-ferrous metal industry to help address these challenges. Our Furnace Services team offers a variety of repair and maintenance services for metallurgical furnaces. Our specialised team has proven methods for completing projects quickly and safely. Our worldwide experience includes turnkey project management, construction, and various scopes of work for demolition and refractory repairs on all types of smelting and refining furnaces. Auburn developed the Results FirstTM programme to provide optimized solutions and results for smelter projects. The programme utilises a proven three-step model for improved results for schedule, budget, safety, and ramp-up to production. Our experienced Project Management teams can handle the planning and construction management of capital projects and plant shutdowns. Our projects have involved smelter/refinery modifications, oxygen plant installations, and sulphuric acid plant audits and maintenance. Our Equipment & Products division supplies specialised equipment and products, which are used in the metals industry for plant maintenance tasks. Our capability to design unique equipment, combined with our ability to source products worldwide, makes us a useful resource to find the best-suited equipment to meet the work-site demands. We specialise in custom remote-control units to handle specific maintenance solutions for smelters and refineries, and custom equipment designs for catalyst handling for Acid Plant maintenance. Our extensive knowledge of and experience with industrial technologies allows us to provide a wide range of Industrial Services. These services include vacuuming, high-pressure water blasting, chemical cleaning, pelletizing, dredging, ore bin clearing, roaster repairs, baghouse/ESP services, and manpower supply for both industrial plants and mines. Auburn?s combined strength of personnel experience, knowledge of industry processes, innovative project methods, and equipment technology make Auburn a unique resource for problem solving on every facet of smelter operations.

Jan 1, 2006

By George L. Wilhelm

Timber support of mine openings continues to be an effective system for ground support, due to its avail¬ability, flexibility, and ease of installation. Timber support of mine openings as a primary method to support loose rock has been replaced to a large extent by rockbolting and by filling systems. How¬ever, the many designs of square-set timber and varia¬tions of crib and stull support that have been developed to suit many stope configurations have proven reliable over many years of application. Integrated in modern excavation and stoping methods, timber remains an im¬portant ground support material for today's mines. ADVANTAGES AND DISADVANTAGES OF TIMBER SYSTEMS Timber, when used as a part of the total support system, is recognized for its unique support properties. More than a cover to prevent minor falls of ground, timber systems have been carefully designed to provide adequate support with sufficient compressive qualities to achieve a safe working environment in extremely diffi¬cult ground conditions. In some cases, a timber support method is designed to yield while retaining its protec¬tive support qualities. Little or no initial investment in equipment or plant is required for incorporating timber into the mining support system. Low cost cutoff saws and portable chain saws are sufficient equipment for effective use of dimen¬sioned (sawed) or round (stull) timber support. Until recently, small sawmills of various complexity were com¬mon at mine surface plants. Sawmills at the mine sites have generally been replaced by timber vendors' mills. Suppliers have been able to use efficient cutting and lumber handling methods to reduce the cost of mine timbers. Most suppliers will package dimensioned mine timber into bundles that are suitable for handling down mine shafts and on level conveyances. The principal disadvantage of timber as a support method is higher material cost and labor cost associated with its labor-intensive installation. Furthermore, stand¬ing timber reserves of mine quality wood are in short supply in some areas, and heavy competition exists for alternative uses of the timber supplies. Vendors are reluctant to supply large cross section dimension tim¬bers relatively free of defects. Some mine operations require 4.8-m (16-ft) lengths of firm timber over 0.09 m2 (144 sq in.) in section and these are difficult to obtain in large quantities. APPLICATION OF TIMBER FOR MINE SUPPORTS Timber used in mine support has been cut from many species of trees. A firm hardwood with physical properties similar to western Douglas fir has been pre¬ferred in the US. Other harder and softer woods, how¬ever, have been used when readily available or where the specific strength or crushing quality of the wood is a desired specification of the support system design. Hard¬ wood, commonly oak, has been used where maximum crushing resistance is required. Mahogany and fir are widely used for shaft guide timber. Normally, timber is used with its core axis parallel to the long axis of the timber dimension. However, in some cases, it is placed normal to its core in a "butt" log position, so as to provide maximum resistance to abrasion of the ore passage adjacent to the cut end of the block. By selective placement of timber block¬ing, controlled resistance to ground closure can be achieved which will prevent early failure of primary sup¬port members of the timber structure. Timber is widely used in modern mining operations as a construction member for chute-lip support. These designs are tailored to each operation to conform to the dimensions of the haulage equipment being used. As a construction material, wood requires none of the spe¬cial equipment necessary for placement of concrete or steel support. Placement of these alternate support ma¬terials requires carefully dimensioned and engineered excavation for their installation. Wood can be easily sawed to fit on location. The successful use of timber in heavy ground de¬pends on the careful and accurate placement of block¬ing and bracing to achieve the controlled yielding re¬sistance needed to support the mine opening. Similarly, frequency, size, and placement of top and bottom block¬ing stulls in flat-bedded deposits are carefully determined to provide adequate support at the mining face. Con¬trolled caving through failure of the stulls may be required as the scope retreats from the earlier mined-out sections. The support program must achieve both of these dimensionless qualities by specification of stull frequency and size. The utility of the square set-system of ground sup¬port and timber support is described in Chap. 2, re¬printed from US Bureau of Mines Information Circular 6691. Four examples of effective use of timber for support of stoping and other mine openings are pre¬sented in other chapters in this section. The Gilman mine's use of Mitchell slice stoping described in Chap. 3 is an early modification of the square-set mining system. This application proved reli¬able for heavy ground and overcame some of the dis¬advantages of conventional square-set timber. Chap. 4 describes the Burgin mine's use of timber with other reinforcement material. This combination of materials achieved high strength and control with yielding com¬ponent members necessary for heavy, squeezing ground. Chap. 5 describes the Bunker Hill mine's use of square¬set timber in a new configuration that provides an effi¬cient and safe support for stoping using small load¬haul-dump (LHD) mobile equipment. Chap. 6 describes some considerations in placing the widely used stull in bedded ore deposits. Finally, in Chap. 7, cost calcula¬tions for

Jan 1, 1982

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977