Search Documents

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs fur improving mine safety. One area of interest to the Bureau is new and improved means for minimizing the hazards of accidental gas ignition or electrical shock should the frame of an off-track machine assume potential above ground. Various means presently used to prevent such occurences are the use of ground fault detectors for phase to ground faults in ac machines, and grounding conductors and diodes in dc machines. In a three phase ac power center, a phase to ground fault may be detected by monitoring the current in the grounding resistor which is required between the power center neutral on the load side of the power center transformer and ground. Another method for detecting a ground fault is to pass the three load conductors through a toroidal core transformer. The phase currents vectorially add up to zero if none of the phases are faulted, and hence the voltage of the transformer secondary is either zero or not zero if one of the phases is unbalanced or faulted.

Jan 1, 1976

By Harry E. Hughes

A section of the largest Superfund site in the country has become a success story for engineering innovation and for cooperative problem solving. “Superfund site” and “success story” are phrases that are not commonly found in the same sentence. Yet, their use seems justified. The project’s certification of construction completion from the US Environmental Protection Agency (EPA) includes a commendation. It reads, “for completing the project nearly a year ahead of schedule, at a cost substantially less than estimated originally and without com-promising the requirements for protection of human health and safety or the environment.” The EPA director who issued that certification also referred to the project as “a positive example of cooperation among all who have a stake in the outcome.”

Jan 1, 1996

By H. B. Pulsifier

The following report on the structure of copper is the result of work done in the laboratory of the Rome Wire Co. early in 1925. Previous work had indicated to the author that excellent results might be expected if a suitable technique in surfacing and etching could be developed. The resources of the Rome Wire Co. enabled this metal to be studied more intensively than previously, although none of the materials were investigated exhaustively. The material presented is hardly more than a preliminary summary of the most obvious character of the metal; a much longer research would have been necessary to solve many of the pressing problems connected with the casting and working of copper. The Rome Wire Co. has generously released the paper; to Dr. E. H. Darby, technical supervisor of the company, are due particular thanks for his appreciation of the importance of metallographic study of copper and for his effective support in the prosecution of the work and in making its publication possible. Dendrites, Cells and Granules The microscope reveals at least three orders of structural units in copper, as in other metals. The largest structural units are the dendrites —spine-shaped crystals building up the masses of metal when it solidifies from a melt or is crystallized from solutions by chemicals or electricity. The nucleus cells, commonly called "grains," are the largest and most conspicuous units of recrystallized solid metal; the limitations of their growth usually confine their sizes to microscopic proportions, although in "single crystals" they may become as large as the piece of metal itself. The granules are the microscopic fine-structural blocks or laminations that build up the nucleus cells; they are revealed when metal is etched with suitable chemicals. The granules are commonly visible at 500 diameters magnification and are plainly visible at 1000 diameters; magnification of the granular surfaces up to 6000 to 9000 diameters shows no finer units, not because of lack of optical resolution but because the chemical attack has left an unfeatured smooth surface.

Jan 1, 1926

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By Stephen C. Tadolini, Steve Bessinger, James Pile, Christopher Mark

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan’s geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro-active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

By Roger L. King

Working in gassy ground conditions is an everyday occurrence for the U.S. coal mining industry. As tunneling operators begin to venture into projects that expose them to the additional hazard of potentially explosive atmospheres, lessons learned by the mining industry over years of experience should be transferred into this industry. This paper will present practices developed by the U.S. coal mining industry for dealing with the problem of excavating material in potentially explosive atmospheres. Procedures will be discussed that can be used to detect and quantify gas prior to mining that have application to the construction industry. Degasification or drainage practices, including predrainage from vertical and horizontal boreholes, will be discussed. Also, ventilation practices commonly used in the mining industry will be presented.

Jan 1, 1985

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By O. Acaroglu

Selection of the most suitable roadheaders (boom type tunnelling machines) for the galleries/tunnels to be excavated in certain rock and under known project conditions is important for avoiding problems during application. This research utilized a multiple attribute decision-making method and studied how this will be applied for the selection of boom-type excavation machines. The Cayirhan Coal Basin was used for selecting roadheaders using the analytical hierarchy process, which is one of the multiple attribute decision-making methods. To conclude, this study reveals that decision-making methods can be used in the process of selecting roadheaders for the excavation of galleries. Keywords: roadheaders, multiple attribute decision-making, analytical hierarchy process.

Jan 1, 2006

By Pingchao Ke

A crystalline polyferric sulfate (PFS) adsorbent was synthesized by oxidizing and precipitating ferrous ions under atmospheric conditions. The morphology, structure, composition and specific surface area (SSA) and adsorptive efficacy to As (III) of the adsorbent were characterized by SEM/EDS and TEM images, XRD patterns, FT-IR spectra, BET SSA analyses and adsorption experiments. The adsorbent presents as morphology of near-spherical aggregate and good crystallinity. A small amount of goethite co-precipitated with PFS in the case of the initial ferrous concentration of 1 mol/L and increased the SSA of the aggregates. The absorbent with co-precipitation of goethite showed good adsorption to As(III) and good filtering performance in the high As(III)-content solution of 10–100 mg/L under acidic, neutral and alkaline conditions (pH 2.09–9.01), and its maximal adsorption capacity and adsorption efficiency were 7911 μg/g and 96% separately. After Adsorption, the stability of the absorbents adsorbing As(III) were evaluated by TCLP tests, and the results indicated that the absorbents adsorbing As(III) were extremely stable, and the concentration of arsenic in all leaching solutions were less than 0.01 mg/L.

By J. Warmbrodt, D. Apel, D. Nutakor, L. Grayson, M. Hilgers

MinerSIM is an augmented reality system with integrated hypermedia that is suitable for training underground miners in the basics of using a jackleg drill to install rock bolts. While statistical evidence shows that rock bolting with such a drill has an inherent level of risk, it is conjectured that this can be mediated with adequate safety training outside of the actual mine environment using a variety of educational media including interactive three-dimensional images, games, animations, and videos to describe the mechanics of rock bolting and its principles. Ultimately, trainees will install rock bolts in an immersive environment mixed with real and virtual images generated via a gaming graphics engine. This paper will discuss considerations, implementation issues, and evaluation methodologies of the MinerSIM system.

Jan 1, 2007

By A. W. Hall

A nuclear method was developed for continuously and automatically deter-mining the moisture content of coal flowing through a bin. Fast neutrons from a 1 curie americium-beryllium source penetrate the coal, are thermalized (slowed down) by hydrogen in the moisture, and are counted by a thermal neutron detector. The difference between the number of these thermal neutrons and those thermalized by dry coal (in a reference drum) is a measure of the moisture content of the coal. A materials handling system was developed and in tests at a commercial coal preparation plant, moisture in coal was monitored continuously within 0.2 percent of values determined by conventional means. The meter responded rapidly to change in moisture content, making it adaptable to automatic process control, and was operated for 1 year without malfunction or recalibration. Shielding of the source by the coal kept the neutron flux level at the bin wall less than 1 milliroentgen per hour, a safe level for personnel.

Jan 1, 1973

By Richard J. Mainiero, James H. Rowland III, Marcia L. Harris

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed. These include: • Minimizing the quantity of toxic fumes produced. • Determining where the fumes may go so workers and neighbors can be moved out of harm’s way. • Preventing the fumes from moving towards workers and neighbors. • Monitoring the air near workers and neighbors so they can be relocated if fumes appear. • Ventilating structures or confined spaces until CO falls below a hazardous concentration.

Jan 1, 2000

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014

By M. Maier

Geographic Information Systems (GIS) has evolved into a powerful tool for analyzing spatial and attribute data in many industries including mining. Modern field data collection techniques add another dimension to the use of data in the field and enhance the utilization of GIS for mining applications. This discussion will review how field data is collected and how office data and maps can be taken into the field to be analyzed and verified using pen-based computers and differentially corrected GPS.

Jan 1, 2001

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

THE machine from which the following results were obtained makes one of a row of seven at work in the Junction North, Concentration Mill at Broken Hill, New South Wales. It consists essentially of a belt for dressing purposes, which travels round two 12-in drums situated at either end of a wooden frame. This frame is supported on wooden legs, and the whole is affixed to two iron castings, one on either side of the frame. A to-and-fro motion is obtained from an eccentric shaft, which, together with the stationary end of the supporting legs, is carried by the iron castings. A belt drive to the forward drum provides a constant rate of travel to the dressing belt.The top half of the dressing belt is supported on 3-in rollers spaced about 12-in centres along the frame of the vanner. A fairly thick dressing belt is used, and no trouble whatever is experienced from the formation of gutters between the rollers.These belts are 28 ft 4 in long, 4 ft wide, 3-16 in thick, and are made of two-ply 32-oz duck, with a coating of rubber on either side. The surface available for dressing is about 10 ft 6 in x 3 ft 8 in- ie, about 38'5 square feet. The machine is driven atthe rate of 245 i-in strokes per minute, while the dressing belt travels at 15 feet per minute...

Jan 1, 1909