Search Documents

By Harpal Parmar

This paper evaluates dynamic methods of pile capacity prediction by comparing their results to static load test results. Dynamic and static pile load test data were assembled from four southeastern states of the U.S. End-of-drive and restrike capacities were evaluated using the Pile Driving Analyzer (PDA) and by wave equation (WEAP) analyses. These were compared to static (Davisson criterion) loads. The best comparison was obtained for restrike PDA results; restrike wave equation analyses values also compared well. The end-of-drive results for both methods-showed relatively poor comparisons. The PDA was recognized as an important tool to measure energy transferred to the pile; this transferred energy was recognized as an uncertainty when conducting wave equation analyses. A statistical analysis showed restrike capacity results to be associated with higher precision and accuracy as compared to end-of-drive methods. The authors believe that restrike dynamic testing is essential to establish long term static soil strength and that it will lead to accurate and cost-effective design of piles.

Jan 1, 1996

By Fred Breu, Ronald E. Heuer

INTRODUCTION The Point Lepreau nuclear generating station was constructed in the late 1970's and early 1980's by the New Brunswick Electric Power Commission. Point Lepreau is a small peninsula on the north shore of the Bay of Fundy, about 55 km west of St. John, New Brunswick. Cooling water for the plant was to be obtained from and discharged into the Bay of Fundy by the system of shafts and tunnels illustrated in Fig. 1. The design engineer for the cooling water system was Albery, Pullerits, Dickson and Associates, Ltd., Toronto. Ferrera-Resco Ltd, Windsor, Ontario, was contractor for construction of the cooling water shaft and tunnel system, which was done between 1976 and 1979. The senior author was project manager for Ferrera-Resco, the junior author served as consultant to Ferrera-Resco on evaluation of certain geotechnical questions which arose during construction. SITE CONDITIONS Geology Except for limited overburden soils at the onshore shaft sites, the tunnels and shafts were constructed entirely in Triassic conglomerate, sandstone, and siltstone, with some shale interbeds. The bedding strike averaged about N6°E, The dip was to the west at about 30° along the Discharge Tunnel and 40° along the Intake Tunnel. Rock along the Intake Tunnel was mostly sandstone and siltstone and more thinly bedded, with RQ D generally in the range of 50 to 60%. Rock along the Discharge Tunnel tended to be coarser sandstone and conglomerate and more thickly bedded, with higher RQ D averaging about 80%. In addition to bedding joints, two other joint systems were identified

Jan 1, 1985

By Elmer Stewart, Richard May

"The Central Mukur deposit was discovered by the Semipalatinsk Geological Exploration Expedition (GEE) during detailed searches from 1977 to 1980. Andas Altyn Ltd., a Kazakhstanian gold mining company acquired the property and commenced mining in 1995. In 1998, Andas-Altyn Ltd. became a wholly owned subsidiary of Eurasia Gold Corporation.The Central Mukur gold project covers a linear series of parallel, discontinuous zones of near surface oxide gold mineralization that covers a distance of 7 kilometers and extends past the property boundaries. The oxide gold mineralization is a result of the regional oxidization of a primary sulfide gold mineralization emplaced in a series of shallow dipping thrust faults. Resources as calculated by the GEE are 3.45 mt at an average grade of 1.84 gmt Au in the C1 +C2 category and 7.52 mt at an average grade of 1.80 gmt Au in the P1 category. The Central Mukur Gold Heap Leach Mine consists of an open pit, heap leach pads, and an ion exchange resin gold recovery plant. Limited gold production (<2,500 ounces/year) has been achieved over the past three years leaching run of mine oxide gold mineralization. Gold recovery utiling cyanide to dissolve the Au and ionic resin technology to recover the Au for the leachate is approximately 60%. Loaded resin is shipped to a treatment plant at Almaty where the gold is stripped from the resin, refined and sold.This paper will describe the geology, mining, and processing of the Central Mukur ore. In addition, it will describe what it is like doing business in Kazakhstan and the transition from a Soviet style operation to a more western style operation.INTRODUCTIONThe Central Mukur Mine is owned and operated by Andas-Altyn Ltd. a Kazakhstanian gold mining company located in northeast Kazakhstan. Andas-Altyn is a wholly owned subsidiary of Eurasia Gold Corp., a Canadian public company listed on the Alberta Stock Exchange. The Central Mukur mine consists of a small open pit, and a heap leach operation that utilizes ion exchange resin to recover gold from pregnant solutions. In addition to the Central Mukur mine, Eurasia also owns the Myaly heap leach gold project which is also operated by Andas- Altyn Ltd."

Jan 1, 1999

By G. Thodos, D. E. Matschke

Cansiderable time and effort frequently are expended to establish, with a degree of confidence, the PVT behavior of pure substances. In particular, a great deal of experimental information contributed by a number of investigators is available in the literature. The data of each investigator, although significant in themselves, cannot be used with a high degree of confidence until they are compared with the continuum of information presented by others. Current interest in thermodynamic and transport properties, for not only the gaseous state but the con-densed state as well, requires that PVT infarmation be presented for both regions. The density dependence on temperature and pressure, when presented as a continuum, is of considerable value in itself, especially since the available equations of state fail to properly account for the PVT behavior in the condensed state. For this reason and to incorporate PVT data recently presented in the literature, this investigation was carried out. In their studies concerned with the thermodynamic properties of methane, Matthews and Hurd in 1946 utilized the data of Kvalnes and Gaddy and Olds, Reamer, Sage and Lacey to establish the PVT behavim of methane in the superheated region and the saturated liquid densities of Keyes, Taylor and Smithl in conjunction with the Clapeyron equation to develop the densities for the saturated envelope. Current activity sponsored by API Project No. 44 under the direction of F. D. Rossini has led to a tabular presentation of compressibility factors for gaseous methane in the superheated region.la These values were obtained by using smoothed residuals, developed from experimental data and the Ben edict-Webb-Rubin equation,&apos; to establish internally consistent compressibility factors for the real gas. This approach offers probably the most precise presentation of PVT information for gaseous methane to date. The PVT behavior of methane also can be represented accurately by equations of state such as the Benedict-Webb-Rubin equation or the Martin-Hoa equation.&apos; These equations, although valuable for analytically representing the PVT behavior, lack precision in the compressed-liquid region. The PVT data available in the literature for methane were utilized to obtain reduced densities that are presented in Figs. 1 and 2 as functions of reduced temperature with parameters of reduced pressure. The critical constants utilized for methane are those reported by Kobe and Lynn." These critical values, T, = 191.1°K, PC = 45.8 atm and p, = 0.162 gm/cc, produce a critical compressibility factor, z, = 0.289. The PVT information, as obtained from the literature, in many instances was not presented in an immediately

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By Richard J. Stoehr

Man has mined in all his time on earth about 3 billion ounces of gold. About one-half of this has been mined in the past 35 years. This gold is roughly in 3 large holdings: one-third held as reserves in Central Banks; one-third held as personal reserves; and one-third is in jewelry or other fabricated products. The world per capita availability of mined gold is increasing and there are many factors and forces shaping gold&apos;s future. Currently, gold has a favorable exchange ratio and this is encouraging many new gold-mining developments. Production is increasing and new techniques are surfacing. The use of gold in the financial markets is increasing in some unique ways and gold is again fulfilling its role as a universal money, making gold&apos;s future predictable. Currently, man is mining gold at the rate of approximately 44 million ounces annually and is therefore adding to the total supply of gold approximately 1.5% of newly mined gold each year. This current production plays a small role in the pricing mechanisms since a very large part of the 3 billion ounces mined in all of history is available to the market in one form or another.

Jan 1, 1984

This report describes the redesign, development and field demonstration of a remote shotcrete lining system, capable of operating in shafts and mines from 8 to 16 feet in diameter at depths up to 1000 feet. The original contractural scope of work outlining problems and remedial measures associated with a previous unit proved inadequate. Significant additional effort was necessary in order to fulfill the project objectives of producing a functionally reliable remote shotcrete lining system. Included with the engineering and technical description of the system, is a comprehensive technology package. Included with this material is ancillary equipment, materials selection procedures, mix-design data, quality control and assurance program, selection and training of personnel and the organizational aspects required to operate the entire system. The report concludes with details of a successfully completed borehole lining operation at the Nevada Test Site. An irregular 104 inch diameter borehole was lined at a rate of 4.8 feet per hour and 20 feet per hour respectively for 8-9 inch and a 2 to 3 inch shotcrete thickness.

Jan 1, 1983

By Nirander M. Safaya

Revegetation success on surface mined lands is dependent upon the nature of the plant growth media. Soil physical and chemical properties dictate the needs for specific reclamation and subsequent management practices. Field experiments were conducted at six coal mine sites in Oliver and Mercer Counties, North Dakota to determine the subsequent effects of a single application of selected amendments on spoil and topsoils over the five year period, 1974-1978. Considerable variations in the physical and chemical properties were found in mine spoils from site to site. The texture of spoils ranged from sandy clay loamy at North Beulah I to loamy at Glenharold, and from sandy loamy at North Beulah 3 and South Beulah sites to loamy sands at the Center site. The pH of the sites ranged from 6.5 at South Beulah to 8.2 at North Beulah 3. In many cases, the pH values of mine spoils were not significantly different from the topsoils. The electrical conductivity (ECe) did not exceed 6 mmhos cm-1 at the test sites even though in other studies much higher values were recorded in the same vicinity. The spoils from Glenharold and North Beulah test sites can be classed as moderately saline, and those from Center and South Beulah as non-saline. The sodium adsorption ratios (SAR) varied from less than 1 to 32, with highest values in the spoils of North Beulah 3 followed by Glenharold; all other sites were nonsodic. Lowest SAR values (less than 1) were found in the topsoiled sites at South Beulah and Center. Spoils of North Beulah 3 test site were highly calcareous, followed by North Beulah 2 and Glenharold. Center mine spoils which were the least calcareous of the test sites, showed the calcium carbonate equivalent three times higher than that of the topsoil. The average calcium concentrations in the spoils of North Beulah 3 and South Beulah test sites were -13 and 14 me 100g -l while at North Beulah 2 and Glenharold test sites 25 and 22 me 100-1-1 were recorded, respectively. The overall magnesium concentrations ranged from an average of 4 to 16 me 100g 1. Sodium concentrations in all sites never exceeded 10 me 100g-1. Phosphorus concentrations on the average at North Beulah 1, North Beulah 2, and Center were 10.2, 4.6, and 22.2 µg g -1 spoil, respectively. Concentrations of potassium ranged from 200 ppm at South Beulah site to more than 375 pp in at the Glenharold site. High concentrations of sulfates (239-2778 µg g-1) seem to contribute to the salinity in these spoils. Chloride concentrations of spoils were low and never exceeded 40 µg g-1 spoil. Based on established critical levels of deficiency for micronutrients in agricultural soils, it seems that none of these were deficient. However, controlled environment experiments did reveal increased plant growth responses when some micronutrients were added to the mine spoils. Treatment effects were highly site specific depending on the nature of the soil/spoil characteristics and, of course, the properties of the various treatments. While slack coal amendment to the spoils at North Beulah 2 site affected significant increases in a large number of variables (both major and trace elements), amendment of the topsoils at the South Beulah test site with leonardite resulted in significant decreases in a number of variables, particularly trace elements. Spoils at Glenharold and North Beulah 3 demonstrated the fewest significant changes due to amendments. Calcium, magnesium, strontium, organic matter and nitrogen were consistently increased from site to site with the addition of lignitic materials. Other spoil/topsoil physical and chemical properties (30 variables) as affected by amendments and time are discussed.

Jan 1, 1982

Cyclone Process for Heavy Metals Decontamination of Sediments

Sep 13, 2010

By Chen Xizhe

The caisson is adapted to the foundation of concentrated heavy building. As there are the flowing sand, boulder or cobble and other serious obstruction, the open caisson can&apos;t sink, the caisson can solve these problems easily. Especially for the stability of the neighour building, the merit of the caisson is outstanding. Therefore, there are the pier, the foundation of heavy instrument and the large water pumping station etc. using the caisson in China. This paper introduce several caissons and successful experience by author&apos;s investigation. It contains the feature and application of the caisson : the examples of caissons such as a huge pier of a bridge acrossing a big river, a large instrument foundation and a large water pump station beside a river; the problem of the design of the caisson and notice items during the caisson construction etc.

Jan 1, 1991

By Robert A. Pond

Heavy (exceeding 35 tons) roadheaders have not seen much use in the United States, but are used extensively in Europe to excavate many types of underground openings in civil and mining applications. Early models of roadheaders were light and suitable only for utility excavation such as drift enlargement or chamber excavation, unless the ground was very soft and easily cuttable. Frontier-Kemper Constructors, Inc. is now using a 45-ton roadheader to excavate two mine slopes in Kentucky and a 70-ton roadheader to excavate a long decline at a new mine in Utah. Results to date indicate that heavy roadhead machines are an effective alternative to both conventional excavation and full-face boring machines in many cases; and where circumstances are favorable are a superior choice. This paper concentrates on applications in the mine development construction industry, but the conclusions are no less valid for civil construction.

Jan 1, 1983

By Pengfu Tan

Lead blast-furnace bullion cools to near its freezing point in an operation known as copper drossing or hot drossing usually contains 0.02-0.06% copper. The removal of this copper is usually carried out in a batch operation known as sulfur drossing. Sulfur is stirred into the bullion at temperatures near its freezing point, and the dross of copper and lead sulfides that floats to the surface is skimmed off manually. A thermodynamic model has been developed to simulate the copper drossing. The phase diagram of Pb-Cu-S system has been calculated, and the effects of the process parameters, such as temperature, copper content, and sulfur content, on the drossing process have been simulated and discussed.

Jan 1, 2006

By P Mitchell, J Proffett, I Munajat

Batu Hijau is an island arc porphyry copper-gold deposit located in the southwest corner of Sumbawa Island in the Sunda-Banda archipelago of Indonesia. Southwest Sumbawa Island is underlain by Early Tertiary, low-K calc-alkaline to weakly alkaline volcanic and intrusive rocks. Within the mine area the oldest exposed rocks are medium- to thick-bedded, medium to coarse andesite volcanic lithic breccia, thin bedded, fine-grained volcaniclastic sandstones and mudstones and hypabyssal porphyritic andesite. In the eastern portion of the mine area there is a thick sequence of quartz diorite that postdates the andesites. A small stock of Equigranualar Quartz Diorite predates the Batu Hijau deposit and occupies the contact between the andesitic volcaniclastic sequence of rocks and the Porphyritic Quartz Diorite. Batu Hijau is a world-class copper-gold deposit that has a drill indicated mineable reserve of 914 million metric tonnes grading 0.525 per cent copper (10.58 billion pounds copper) and 0.403 g/t gold (11.8 million ounces gold). Mineralised material not in reserve accounts for an additional 580 million metric tonnes at 0.328 per cent Cu (4.19 billion pounds copper) and 0.171 g Au/T (3.19 million ounces gold), and including an oxide copper resource of 57 million tonnes at 0.37 per cent Cu and 0.12 g Au/T. Copper and gold mineralisation is directly related to quartz veining and wall rock alteration that developed with multiple tonalite porphyry intrusions. The tonalites were emplaced along the contact between the andesitic volcaniclastic rocks and quartz diorite intrusives. Copper and gold are zoned around the porphyry intrusions, which are designated by their contact-age relationships and other features as Old Tonalite, Intermediate Tonalite(s), and Young Tonalite(s). The Old Tonalite was the first copper-bearing intrusion, and although it is the smallest intrusion it has the highest quartz vein density, the strongest alteration and the highest grade. At least two tonalite porphyry intrusions followed the emplacement of the Old Tonalite. Each of these intrusions was associated with less quartz veining, weaker hydrothermal alteration and lower grade copper and gold than the previous intrusion. The intrusive cycle culminated with the emplacement of the Young Tonalite, which contains relatively few quartz veins, is weakly altered and mineralised. Hypogene hydrothermal alteration and sulphide mineralisation developed in five temporally and spatially overlapping stages. These stages consist of Early, Transitional, Late, Very Late, and I Zeolite alteration. Early alteration and sulphide mineralisation accompanied each tonalite porphyry intrusion, but with diminished intensity in each subsequent intrusion. Transitional and later stages of alteration and mineralisation postdate the tonalite porphyries and overprint Early stage alteration and mineralisation. Early alteration and mineralisation consisted of biotisation, secondary magnetite and plagioclase development, fine porphyry-style stockwork veining and ore mineralisation. Magnetite-biotite????quartz stringers and dark micaceous (biotite-sericite) veinlets were developed. The veinlets were accompanied by biotisation of magmatic mafic minerals and groundmass. Thin, irregular and discontinuous æAÆ type quartz veinlets and fine-grained chalcocite, digenite and bornite mineralisation accompanies the Early alteration. It is hypothesized that most of the copper mineralisation was originally deposited as bornite, digenite and chalcocite. Secondary plagioclase was added along the selvages of the early quartz veinlets. Early alteration is pervasive within and proximal to the tonalite porphyries. In the distal portions of the deposit, andalusite and anthophyllite formed at intermediate to shallow depths, and in the deeper portions of the deposit, respectively. The andalusite and anthophyllite probably developed at the same time as the early magnetite-biotite-quartz alteration in the core of the deposit. Transitional-age alteration consists of oligioclase/albite-sericite-chlorite- quartz-¦vermiculite and is associated with æBÆ quartz veins. Through-going planar æBÆ veins are thicker than æAÆ and æA-familyÆ veinlets and have chalcopyrite????bornite along vuggy centrelines and narrow oligioclase????albite alteration envelopes. Rare æCÆ chalcopyite¦quartz veinlets were also formed during Transitional alteration. During Transitional alteration early copper sulphide minerals (chalcocite, digenite and bornite) are converted to bornite and chalcopyrite. The majority of the copper (50 - 70 per cent) in the deposit is contained in ores in which chalcopyrite is the predominant sulphide. Late alteration consists of feldspar destruction and replacement by sericite and other minerals. The late alteration is accompanied by the development of æDÆ sulphide veinlets and veins. These veins consist of pyrite and quartz????chalcopyrite. Within the halos of the late pyritic veinlets biotite is replaced by sericite, quartz-sericite, quartz-andalusite, or quartz-pyrophyllite+kaolinite replace plagioclase, and magnetite is converted to specularite and/or pyrite. In the periphery of the deposit, the feldspar destructive alteration, together with outer zones of Transitional-age alteration, constitutes what is commonly referred to as a æpropylitic zoneÆ. Very Late hydrothermal alteration is also characterised by feldspar destruction, but differs from Late alteration in that feldspar is replaced by smectite in association with sericite and chlorite. Sulphide mineralisation in this stage consists of sphalerite, galena, tennantite, pyrite and chalcopyrite. The last stage or I Zeolite alteration consists of low-temperature, open space filling consisting of stilbite or laumontite¦calcite. Supergene oxidisation of the orebody extends to a maximum depth of 210m. Isolated deep oxidation occurs along open fracture zones to depths of ~400 metres along æDÆ vein filled fracture zones. Weak supergene copper enrichment occurs in a thin horizon (15 to 60 m thick) that blankets the top of the deposit. The main supergene copper mineral is secondary æsootyÆ chalcocite replacement of sulphide grains and as veins.

Jan 1, 1999

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By Axel Preusse

For the last 150 years, subsidence damage to the surface has been an unavoidable phenomenon associated with underground coal mining. In particular, the mechanization of mining methods in multiple seam mining and the concentration of mining activities in densely populated European metropolitan areas (e.g., Ruhr, Upper Silesian industrial region) have led to mining having a very strong influence on the earth?s surface. In both these regions, surface subsidence of more than 20m has been reported up to now in comparison to the original state. Underground coal mining in these regions strongly impairs all kinds of surface use, such as urban and industrial development, infrastructure (roads, waterways, and railways) and pipelines?without restricting the functionality of those objects to a greater extent. Demanding and, in some cases, globally unique engineering solutions have been developed and implemented for this purpose. The previously mentioned mining and industrial regions are still very strongly characterized by the (increasingly declining) coal industry and will remain dependent to a large extent and for an indefinite period on artificial drainage measures because subsidence that has already occurred is irreversible. This paper will primarily discuss the prediction of subsidence that is caused by intensive multiple seam mining and its influence on surface objects (e.g., underground pipelines). However, an approach for predicting ground uplifts due to rising mine water as a consequence of mine closures will also be described.

Jan 1, 2012

By Tony S. Calayag

Throughout the mining industry today, new bearing materials - ZA* high-performance zinc-aluminum alloys - are reducing costs of maintaining and rebuilding a wide range of equipment. As replacements for bronze bearings, installed in original equipment at the plant or during maintenance and repair operations in the field, the zinc alloys frequently provide better or equal performance at lower cost. The ZA Alloys The ZA alloys are a family of three high-performance zinc-aluminum alloys that compete in cost and performance with cast iron aluminum and bronze. The growing number and uses testifies to the versatility of these alloys and is encouraging their consideration in a wider range of applications. The ZA alloys are referred to as ZA-8, ZA-12, and ZA-27, the numbers corresponding approximately to the percentage of aluminum each alloy contains. ZA-8 is a permanent-mold casting alloy and is usually selected for decorative purposes; ZA-12 provides both performance and cosmetic benefits; ZA-27 offers the greatest functional strength. The term high performance ZA alloys distinguishes them and their improved engineering properties from traditional zinc die casting alloys. Maintenance Savings At its mine in Timmins, Ontario, Kidd Creek Mines Ltd. operates over 40 Joy VCR- 150 crawler-mounted air-powered rock drills. Most of the drill components undergo severe stress as the drill batters through the under-ground rock. As the components wear, the drill bits wobble; when the wobble becomes excessive, the drills are rebuilt. In the gear train, which rotates the drill steel, there are three planetary gears with - historically - bronze bushings. Since the planetary gear bushings are wear items, they are routinely replaced during overhaul. The bronze planetary gear bushings (three bushings per assembly) were replaced up to five times annually. With 43 drills in use, bushing consumption approached 600 per year. At the manufacturer&apos;s replacement part cost, the 600 bushings and gears would cost more than $20,000 a year. Even though a major saving was achieved by having the bronze bushings manufactured locally, the 600-unit annual usage provided ample incentive to investigate other ways of lengthening drill life and reducing the part costs. One approach was to consider using a bushing material that offered good bearing properties, but was lower in cost. About three years ago, ZA-12 zinc-aluminum casting alloy, costing less than half as much as bronze, was evaluated and selected for testing. One hundred ZA bushings were manufactured and placed in service as the drills came in for rebuilding. At the next rebuild the "drill doctor" (drill maintenance mechanic) noticed that, although the bronze bushings were completely destroyed, on occasion the zinc alloy bushings were not. In addition, he noted that some of the ZA bushings showed less wear than the bronze bushings. Because the bushings were changed routinely during each overhaul, the actual operating life of each bushing was not determinable. Therefore, it was not possible to statistically compare the life of the ZA bushing against the bronze. However, the desired life of the part was from overhaul to overhaul. So the ZA alloy obviously met the objective, giving equal or better life than bronze at a significantly lower price. Based on the favorable results of the testing under actual operating conditions, Kidd Creek maintenance personnel decided to switch permanently to the ZA bushings for rebuilding the VCR-150 rock drills. Original Equipment Application As one of the leading companies marketing the ZA alloys, as well as a zinc -copper-silver mining company, Kidd Creek is interested in developing applications for the alloys by original equipment manufacturers such as joy Manufacturing. Kidd Creek marketing representatives provided joy with information on the Timmins mine tests, along with ZA-12 bushings for evaluation and testing. Based on this information, joy installed ZA bushings in 12 new VCR-150 units and delivered them to customers for use in such areas as granite quarries and copper, lead, zinc, and limestone mines. During the following year, joy engineers closely monitored repair reports to verify the performance of the ZA part. The engineers&apos; findings convinced them of the advantages of ZA-12. As a result, joy now uses ZA-12 bushings in the manufacture of its VCR-150 air tools. Advantages for Casters and Users In the foundry, the new alloys have proved their castability and profit potential in sand and metal permanent-mold processes, as well as the new graphite permanent-mold gravity casting process. The energysaving, pollution-free and ease-of-machining benefits they offer are important to all of these processes. Most recently, the high-performance alloys entered the arena of cold-chamber die casting, where they provide properties beyond those of

Jan 7, 1983

By D. William Tedder

Several bauxite residue sands and muds produced by Bayer plants in the U.S. and overseas have been fractionated using dry and wet magnetic separators. The magnetic sand fractions typically contain about 60 wt% iron and the bulk of the radioactivity in this waste. The muds are more difficult to process than the sands, but some fractionation is possible using a combination of flotation and magnetic separation techniques.

Jan 1, 1984

By Sean Gallagher, John R. Bartels, Dean H. Ambrose

Remote operation of continuous miners has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred when using remote controls. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory examined the workplace relationships between continuous miner operators and various tramming modes of the equipment using motion captured data, predicted operator response times, and field- of- view data to determine causes of operator-machine struck-by events in a virtual mine environment. Factors studied included machine speed, direction of escape, operator facing orientation relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck. It is hoped that this data will provide an improved rationale for operator positioning for remotely operated continuous miners.

By Gábor Csicsovszki

We have developed a novel method - at the laboratory scale - comprising an ion-exchange separation and a membrane-electrolysis step for the purpose of zero-waste regeneration of spent HCl pickling liquors originating from hot-dip galvanizing of common steels. It is aimed at the parallel regeneration of HCl and iron. Experiments revealed that iron can be electrodeposited at high current efficiencies by maintaining the following conditions: 0.04-0.08 M HCl, 500-1000 A/m2, 20°C and stationary electrolyte in a conventional cell. Zinc in the solution did not disturb the deposition of iron, however it contaminated the product and it poisons the anion-exchange membrane required to tackle acidity during electrolysis. For a preliminary separation, anion-exchange tests were carried out to produce pure iron solutions. Beyond the equilibrium studies, column experiments were carried out showing that low flow rates of the loading solution and the ~1.5 M HCl eluent are essential for separation.

Jan 1, 2006

By A. K. Singh

Between the main fan and the coalface in a mine a lot of air is lost through leakage at stoppings, doors, air-crossing etc. so that a much larger quantity of air has to be circulated by the fan in order that the stipulated quantity of air reaches the face. Stoppings are of vital importance not only for effective ventilation of underground mines but also for isolation of areas affected by fire or susceptible to spontaneous heating. Generally, isolation stoppings are made of brick in cement mortar. If the area is far from the pit or unapproachable, it is very difficult and sometimes impossible to build these stoppings. To overcome these difficulties, particularly near fire affected zones, an alternate successful attempt was made in Indian mines to make a plug underground, from surface through borehole, using cement concrete. In this paper the salient features of the methodology adopted for construction of the plug and the experimental procedure for the measurement of air leakage by SF6 tracer gas is described. Measurements of air leakage through rows of ventilation stoppings in two mines viz. Moira (Jambad and Kajora seams) and Kuardi11/12 (Niga seam) collieries of Eastern Coalfields Ltd. (ECL) have been incorporated. Results of experiments conducted at the Central Mining Research Institute (C.M.R.I) to determine leakage through25 and 38 cm thick brick stoppings are also discussed. Results of all these studies are compared, which show that the efficacy and reliability of the remote filled cement concrete plug in respect of air permeability is satisfactory.

Jan 1, 2004