Search Documents

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By Mary Nelima Ondiaka, Kayode Henry Talabi, Oladunni Oyelola Alabi, Fatai Olufemi Aramide, Francis Gitau

Iron ore is essential in steel making; however, high-grade ores have diminished, making low-grade ores inevitable. These lowgrade iron ores need further beneficiation to upgrade the iron content. Currently, traditional physical and chemical methods are utilized and are not environmentally friendly. Bio-beneficiation techniques have emerged as a sustainable alternative for mineral recovery. This review delves into recent bio-beneficiation advancements for enhanced low-grade iron ore recovery using microbes. Research has revealed that bio-beneficiation methods such as bio-leaching, bio-flotation, and bio-flocculation have proven successful in iron recovery from ores. The bio-beneficiation process occurs in mild conditions using bio-reagents derived from microbes and offers a reduction of chemicals used in processing. Bio-beneficiation of iron ore potentially offers a relatively energy-efficient, cost-effective, and environmentally friendly method of maximum iron ore recovery. However, this review has identified a scaling-up difficulty in which a future approach for industrial-use applications is offered following a thorough sustainability assessment. Bio-beneficiation, using microbial processes, provides a viable avenue for maximizing iron ore recovery while tackling the constraints of dwindling high-grade iron ore resources and environmental sustainability.

Mar 16, 2024

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By The Honourable George Prudham

"I AM PLEASED indeed to be present with you here today and to be taking part in the proceedings of your convention. You have been greeted and welcomed to the Province by Premier Manning who is also provincial Minister of Mines and Minerals, and to this City by Mayor Hawrelak. As Minister of Mines and Technical Surveys in the federal government and as Member of Parliament for Edmonton West, I have been asked to share the honour of extending greetings and a cordial welcome to all.It is a happy coincidence that this representative national gathering, indicative of the growing strength and significance of a great basic Canadian industry, is taking place in the Macdonald Hotel, the new addition of which marks another important step forward in the progress of this City and district.This happens to be the third national convention of the C.I.M. that I •have had the pleasure of attending and I trust that I am not presumptuous in expressing the hope that I will have the opportunity of attending many more conventions of the Institute in my present capacity.Dr. Kidd has bestowed on me a high honour by asking me to be Co-Chairman of this Inaugural Session of the Convention and thus to share with him the responsibility of presiding over the proceedings of this afternoon."

Jan 1, 1953

By Haysler Apolinário Amoroso Lima, Francisco Pereira Netto, Vladnilson Peter de Souza Ramos, Bruno Nery Stoco, Gilvan Nascimento de Souza

Em um mercado dominado por tijolos de Al2O3-MgO-C, o revestimento de trabalho de panela de aço monolítico e CarbonFree se apresenta como uma tecnologia disruptiva para um novo patamar de qualidade do aço e eficiência energética. O presente estudo relata a motivação para a implementação do primeiro fundo de panela de aço com revestimento monolítico concretado in situ no Brasil, e apresenta uma análise preliminar dos resultados e vantagens observadas. Uma panela da Ternium Brasil foi revestida com refratários de Al2O3-MgO, e colocada em operação sem nenhuma necessidade de ajuste na operação da aciaria. A partir dos dados de processo e das medições a laser, calculou-se o desgaste do revestimento, bem como verificou-se a garantia de qualidade nos aços IF (interstitial free) e a maior preservação na temperatura do aço durante o refino secundário.

Oct 1, 2019

This paper aims to increase our understanding about existing capacity-building approaches and their implications for obtaining a social license to operate in the mining industry. The notion of ?capacity building? is gaining increasing currency in the mining sector in developing countries due to a rapid rise in the globalisation of mining operations. Capacity-building is conceived here as a process that lasts after the mine-cycle, intended to provide local mining communities with tangible skills and knowledge to gain meaningful employment in mining or other industries relevant for the local economy. Building community capacity to understand and effectively respond to these transformations is vital for obtaining a social license to operate, as it promotes sustainable and locally relevant development. Accountability mechanisms such as global norms and international standards increasingly highlight the need to build capacity among stakeholders, particularly among local communities adjacent to mining operations. International frameworks and mining companies have embraced the notion of capacity-building as a driver to assist corporate social and operational performance. However, this narrow understanding of capacity-building through the prism of corporate social responsibility and ?best practice? is preventing the industry from meaningfully impacting communities and maintaining a social license to operate. This latter notion is being widely embedded across multiple industry sectors, as a social and economic reward from mining companies to compensate communities for natural resource extraction and gain social acceptance. Although both concepts are widely recognised in the minerals industry, insufficient attention has been paid to the implications of applying a top-down (mining-orientated) or a bottom-up (community-orientated) capacity-building approach for obtaining a social license to operate, or indeed how these two concepts are linked and applied in practice. At times, communities lack the necessary capacities in the form of education and skills to deal with mining-led livelihood transformations. This is preventing both mining companies and communities from forging sustainable livelihoods and responding to mining-led livelihood transformations, a situation that is creating discontent among communities and reducing the possibility of obtaining and renewing a social license to operate for the industry. Based on a review of current scholarly debates, accountability mechanisms in the mining industry and fieldwork findings in Colombia, this paper will contribute to an understanding of the implications of existing capacity-building approaches that support a social license to operate.

Aug 1, 2013

By N. Iverson, E. Haft, V. T. McLemore, M. Woodard, E. Owen

Present and emerging technologies are renewing interest in domestic rare earth elements (REE) production. REE deposits throughout the North American Cordilleran alkaline-igneous belt are being re-examined for their economic potential. In New Mexico, the mineral deposits found in this belt are associated with Eocene–Oligocene alkaline to calc-alkaline igneous rocks. Four areas in New Mexico have been examined for their REE potential. The chondrite-normalized REE patterns are similar for all four districts, even though different REE minerals are found. Crandallite, xenotime, bastnäsite and brookite are found in fluorite veins and carbonatites at Laughlin Peak. Bastnäsite was extracted during fluorite processing from 1954-1980 from the Gallinas Mountains, where samples as high as 8% total REE are found in fluorite veins. Other REE minerals include agardite, parasite, xenotime, and monazite. Allanite, thorite and as much as 8133 ppm total REE are found in fluorite veins in the Capitan Mountains. In the Cornudas Mountains, exploration along the outer edge of the Wind Mountain nepheline syenite laccolith and within phonolite dikes, plugs, skarns and carbonate-replacement deposits in Chess Draw contain as much as 3110 ppm TREE, hosted in eudialyte, monazite, bastnäsite, and calciocatapleiite.

Feb 1, 2023

Dynamic Simulation of an Alumina Refinery

Sep 13, 2010

By B. Genc, P. Malepfane

This study proposes a new approach to reduce the environmental impact during surface mining by improving environmental factors through the incorporation of carbon footprint into strategic mine planning. Two key variables were analysed by contrasting and comparing the baseline and optimised models generated. These variables include net present value, which helps determine the financial feasibility of the mining models and their carbon emissions. The variables were analysed by using linear regression, Spearman’s correlation, a P-value hypothesis, and an exponential decay test. Results show that at Mine A the projected net present value was 62% higher than when running a baseline model. Furthermore, the net present value from the baseline model portrayed a high rate of decay at 0.667 versus 0.118 from the optimised model. This indicates the baseline model’s sensitivity to long-term project timelines and fluctuating markets. The optimised method presents an opportunity to manage emissions during the high operational costs phases. It is represented by a 31% improvement in carbon emissions during the periods of high operational costs, whilst maintaining a positive net present value when compared with the baseline model. It was shown that the optimised model presents a better chance of achieving financial feasibility and balancing environmental impact, thereby ensuring that Mine A can align with the environmental aspect of economic, social, and governance principles through lowering the carbon footprint resulting from its hauling operations.

Jan 30, 2026

By Arash Khosravifar

The seismic design of extended pile shafts for the combined effects of dynamic shaking and liquefaction-induced lateral spreading is investigated using nonlinear dynamic finite element analyses (NDA). Results of NDA parameter studies are used to illustrate how inertia and lateral spreading loads combine during shaking. The NDA results are used to evaluate equivalent static analysis (ESA) methods. Implications for design practice are discussed.

Jan 1, 2010

By AIME AIME

COMMITTEES. CANAL ZONE.-Col. George W. Goethals, U. S. A., Chairman; Lt.-Col. H. F. Hodges, U. S. A. ; Lt.: Col. D. D. Gaillard, U. S. A. ; Lt.-Col. William L. Sibert, IT. S. A. ; H. H. Rousseau, U. S. N.; Col. W. C. Gorgas, U. S. A.; Maurice H. Thatcher ; Joseph Bucklin Bishop ; Lt.-Col. Charles F. Mason, U. S. A.; S. B. Williamson ; Major Eugene T. Wilson, U. S. A. ; Edward Schildhauer ; Henry Goldmark ; Edward C. Sherman ; W. G. Comber ; W. B. Corse ; J. A. Walker; Joseph A. Le Prince; J. A. Smith ; Lt. Frederick Mears, U. S. A. HAVANA.-V. T. Polledo, Chairman; Diego Lombillo Clark, Jose Primelles, J. R. Villalon, Jose Artola, J. Ducassi, Luis Morales, Enrique Montonlieu. ENTERTAINMENT ON SHIPBOARD.-William L. Saunders, Chairman; Mr. and Mrs. S. D. Warriner, Mr. and Mrs. Thomas Robins, Mr. and Mrs. George.D. Barron, Mr. and Mrs. R. B. Watson, W. E. Greene. GENERAL MANAGEMENT. .Joseph Struthers, Chairman; Albert E. Vaughan. There were ten sessions of the Institute held for the presentation and discussion of, technical or professional papers. Eight of these sessions were held on the steamer while en route, and two in the ball-room of the Hotel Tivoli, at Ancon, C. Z. Mr. David W- Brunton, President of the Council, presided at all the sessions, except the sixth, at which Mr. Charles Kirchhoff, past President, occupied the chair. The following list includes the papers presented in oral abstract by the authors: First Session., October 24. The Summit Hill Mine-Fire, by W. A. Lathrop, Philadelphia, Pa. Mine-Fire at the Calumet and Hecla Mine, No. 8 Shaft., by S. D. Warriner, Wilkes-Barre, Pa. Fire in the Big Lick Stope, Lykens Valley and Williamstown Colliery, by R. V. Norris, Wilkes-Barre, Pa. Mine-Fire in the Hecksherville Valley, Schuylkill Field, Pa., by W. J. Richards, Pottsville, Pa.. Fire in the Monarch Mine, near Rock Springs, Wyo., by S. A. Taylor, Pittsburg, Pa.

Dec 1, 1910

By R. Barthel, O. Nitzsche, J. Pateiro Fernández, T. Cramer

The Hong Gai coal field in northeast Vietnam has been the main coal mining area of Vietnam for more than 150 years. Anthracite coal is produced from several open pit and underground mines situated close to the UNESCO world natural heritage site Ha Long Bay. The mining-induced environmental impacts such as dust emissions, acid mine drainage, and visual impairments due to waste dumps resulted in severe conflicts of interests regarding future land use and the protection of the world natural heritage site Ha Long Bay. Within the RAME project (Research Association Mining and Environment in Vietnam), Brenk Systemplanung is contributing to an improved environmental and sustainable planning in Vietnam&apos;s mining industry and the reduction of environmental impacts on Ha Long Bay by developing suitable and sustainable technology and planning measures (e.g. for dump construction/rehabilitation, predictive modelling, and/or monitoring) for Vietnam&apos;s leading coal producer.

Jan 1, 2011

By F. Dinter, C. McGregor, Q. G. Reynolds, L. Hockaday

The necessity of reducing greenhouse gas emissions to limit the impact of anthropogenic climate change means that all industrial processes should investigate their options towards decarbonization. Iron, steelmaking, aluminium, and cement production produce the most industrial emissions. Although most research focuses on decarbonizing these industries, minerals processing industries must be decarbonized to achieve net zero emissions goals by 2050. Incorporating renewable energy sources and avoiding the combustion of fossil fuels are two ways to reduce greenhouse gas emissions. This paper reports on the results from a dynamic process model developed to investigate the feasibility of concentrating solar thermal pretreatment of manganese ores to pretreat carbonate-rich manganese ores for increased ferromanganese smelter productivity and reduced greenhouse gas emissions. The results indicate that pretreated ores reduce the energy requirement for smelting significantly for some ores and lowers total carbon dioxide emissions by 13 to 19% compared to the traditional smelting route. A high-level economic evaluation shows that solar thermal treatment is financially viable for low cryptomelane, high braunite ore that is common in the Kalahari Manganese Field.

Dec 11, 2024

By R. C. Troxell

Alternative methods of analyzing data acquired by the Morenci copper concentrator process control instrument-computer system are presented. Experimental measures of ore characteristics, for proposed feed forward control, are introduced. These include on-line indexes of ore hardness, ore density, ore dusting, and ore color. Comparison of metallurgical results before and after computerized process control implementation, allowing for differing ore grades, oxidation, hardness, and fineness of grind, also is described.

Jan 1, 1979

By Renato Ferreira Lima e Corrêa Pereira

Na manufatura de produtos metálicos, o forjamento é o processo de transformação a quente de materiais dúcteis, como aços e ligas, através de conformação mecânica efetuada com esforço de compressão por uma prensa, de modo que eles assumam os formatos desejados. Este processo normalmente é utilizado para produzir peças de formas complexas e com uma maior precisão dimensional de acordo com a especificidade exigida pelo cliente final. Para obter resultados de qualidade, foi necessária a implantação de técnicas de medição indireta de última geração, que proporcionam ganho de tempo e a redução de desperdício de energia e material, além de aumentar a segurança, reduzindo a presença de pessoas próximas aos materiais para medições manuais. O presente trabalho trata da criação de um sistema de visão que, por meio de análise de imagem, é capaz de coletar a medida do perfil de barras em uma Forjaria em tempo real, podendo ser utilizado durante a operação da prensa, para garantir que o material está em conformidade com o especificado. A execução do sistema em produção aponta que as medidas realizadas apresentam desvio máximo de 2mm em relação àquelas realizadas pelos operadores.

Jul 30, 2018

By W. A. Gibson, A. D. Trujillo

The Santa Rita copper deposit first served as a source of native copper for Indian implements and weapons. In 1801 Santa Rita copper, trans- ported by mule train to Chihuahua, began to be used commercially for making coins. It was a small- scale operation made difficult by Indian raids, transportation costs and depletion of the higher grade ores. There was, moreover, no known method for economically extracting copper from the under- lying low grade sulfide ores. Originally, copper and copper oxide ores were mined by underground methods, but there was virtually no development of the deposit-which became United States territory after the Treaty of Guadalupe Hidalgo in 1848-for almost a hundred years. A number of small underground mines had been started during that time, but it was not until 1873 that all the principal claims were consolidated under one control.

Jan 1, 1966

By J. P. Walsted

Offgrade chromite concentrate, with a Cr-Fe ratio of 1.3 to 1.4 has been successfully smelted to produce useful ferroalloys. The Cr-Fe ratio is not improved, but the alloys can be used without a too drastic change in normal steel-mill practice. The ordinary high-carbon ferrochrome has been successfully produced by smelting under highly acid smelting conditions. An alloy containing 50 percent chromium was produced at a power consumption of 4,490 kw.-hr. per ton of alloy. Alloys containing 20 percent silicon were made by direct smelting chromite concentrate and silica.

Jan 1, 1956

By L. X. Yu

As is known, the oxidized antimony and antimonate are hard to treat. A new combined mineral processing flowsheet which is controlled in grinding and classification ?bulk floatation?gravity separation is adopted to dispose of gravity-separated tailings (antimony content: 1.48%; oxidization rate: 68.92%) in Muli Antimony Mine, the grade of floatation antimony concentrates is 32.64%; the grade of gravity-separated antimony concentrates is 26.99%; the combined grade of floatation and gravity-separated antimony concentrates is 30.85%, and the total recovery of antimony is 70.64%. Adopting the new mineral processing technique have solved the problem of over grinding of antimony ore by controlling grinding and classification, recovering effectively the sulfide antimony and the easy floatable oxidized antimony of fine size by bulk floatation, recovering effectively the oxidized antimony which is hard to float by classified gravity separation. This is a great breakthrough in the mineral processing technique of the recovery of the oxidized antimony. At present, favorable economic benefit has been obtained from the application of this processing technique in Muli Antimony Mine.

Jan 1, 2014

By Janaina Gonçalves Maria da Silva Machado, Carlos Mateus Braga de Almeidar, Leandro Miranda Nascimento

Knowing the reduction of the concentration of iron in the mineral load extracted in the last decades and, therefore, greater need for comminution processes, there is no denying that iron ores tend to get increasingly thin for steelmakers. In Reactors such as Blast Furnace and others of fusion-reduction, where the reduction of the iron ore for the metallic iron for the steel production occurs, we observed that one of the alternatives is to agglomerate the raw materials in the form of briquettes, improving the kinetics of the chemical reactions, since ores in the form of fines impair factors such as the permeability required for reduction. These agglomerates are composed of a reducer, fines of ferrous materials and a binder material, and require, in addition to satisfactory Metallization, mechanical resistance, avoiding losses when the compound is fragmented during transport or during its deposition in the Steel Reactor. In the following work, Briquettes were produced with Charcoal, Pellet Feed, Molasses Cane and Hydrated Lime. The mixtures were pressed under different conditions of Pressure (1, 2 and 3 tons-force), and pressing time (20 , 60 and 100 seconds), aiming to analyze the influence of these two variables on the drop tests, mechanical resistance of the briquettes generated.

Oct 1, 2019