Search Documents

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

By Trevor Yeomans

"NVI Mining’s Myra Falls Operation is a forty year old underground mining operation feeding a 4000 mtpd concentrator.The current Mill, built in 1985, was designed to process a large massive sulphide ore-body. This ore-body, known as the “HW”, contains about 50% pyrite. Value minerals are chalcopyrite, and sphalerite, with precious metals occurring in all mineral types.By 1997, mining of a new ore-body, known as “Battle-Gap” commenced. Mineralogically complex, the new orebody contains about 15% pyrite, copper minerals including primary chalcopyrite, secondary bornite, chalcocite and tennantite, combined with increased galena and sphalerite.Flotation performance generally decreased with increasing amounts of Battle-Gap ore types, with both copper concentrate quality (increased lead and zinc content) and copper recoveries being affected.Following significant metallurgical testwork, a new fully sequential copper-lead-zinc flotation flowsheet and reagent scheme was developed.This sequential flowsheet was progressively installed and commissioned during 2006.Copper concentrate lead and zinc smelter penalty contents have been reduced by some 40%, whilst increasing copper recovery by 10%.INTRODUCTIONNVI Mining operates the Myra Falls Operation near Campbell River on Vancouver Island, BC. The complex has been in operation since 1966 with mining being predominantly underground. One unique feature of Myra Falls is that the mine operates within a BC Provincial Park.In 1985, a new large massive sulphide ore-body (HW) had been defined, and metallurgically tested. A new concentrator was built based upon this massive pyrite, chalcopyrite, and sphalerite mineralization producing copper and zinc concentrates by conventional flotation methods."

Jan 1, 2008

By Theodore S. Jordan

The discovery of a major porphyry-type copper deposit on the Papago Indian Reservation in Pinal County, Arizona was announced by El Paso Natural Gas Company in 1968. The deposit, known as the Lakeshore Property, contained an estimated 470 million tons of sulfides and oxides averaging 0.75 percent copper. History and Geology of the area have been described by Harper and Reynolds (1969). El Paso subsequently&apos; entered into the agreement for joint development of the property with Hecla Mining Company, with Hecla as the operator. The ore body consisted of three types of mineralization: 1) Disseminated Oxide Ore, <1% Cu 2) Disseminated Sulfide Ore, <1% Cu 3) Tactite Ore, >1% Cu

Jan 1, 1985

By F. Kongoli

Viscosity is an important parameter of copper smelting and converting processes. It affects the settling of matte or metal droplets in the slag, distribution of elements etc, Despite this importance, confusion exists on the viscosity of copper smelting slags as a result of disagreements found among the measured viscosity data of several authors especially in the slags of high ferric iron content and close to magnetite precipitation. In this work a critical review of the existing data on the viscosity of copper smelting slags has been first carried out and the effect of oxygen potential on the viscosity of copper smelting slags has been clarified through a coupled quantification of viscosity and liquidus temperature. The confusion in the literature has been clarified and the importance of the relation between the viscosity and the liquidus temperature is discussed,

Jan 1, 2003

By Arnaud-Guilhem de Loze

Este artigo apresenta uma ferramenta de simulação computacional desenvolvida com o objetivo de auxiliar a adoção de melhores práticas de controle do forno durante períodos sem produção. O sistema desenvolvido permite simular as temperaturas do revestimento refratário de um forno de tratamento térmico de tubos em função da evolução da temperatura da atmosfera interna em diferentes cenários. O simulador foi desenvolvido baseado em um modelo matemático dinâmico validado, que utiliza um sistema de equações de transferência de calor discretizadas. Realizou-se a validação desta ferramenta computacional com a utilização de dados reais de uma campanha de medição de temperaturas. A comparação dos resultados apresentou pequeno erro entre simulação e valores reais coletados. A utilização desta ferramenta auxiliou a definição de estratégias de controle do forno durante períodos improdutivos, possibilitando redução do consumo de energia e retomada da produção com garantia da qualidade do produto.

Aug 17, 2017

A variety of cement raw materials occur within the Cenozoic sequence in Northland. These form the basis of Golden Bay Cement&apos;s cement manufacturing operation at Portland, Whangarei. High grade limestone is taken from the Whangarei Limestone formation, which has been shown to have been sub-aerially weathered and developed mature karst features prior to deposition of the overlying allochthon sediments. In this instance, remobilisation of allochthon sediments following uplift and erosion is inferred. At Portland Quarry, argillaceous limestone is extracted from deformed thrust sheets in the allochthon sequence. Quarry operations have been designed to handle the steep asymmetric folds, thrust faults and fracture zones that affect the resource.

Jan 1, 1999

Suddenly, mining has been thrust into the limelight. It has a large image that casts its shadow over New Zealand. Is it any wonder that resistance has heightened and that an almost unprepared populous is currently struggling to protect the very land they hold dear. Next to the atomic bomb, mining has the demonstrated power to massively change the land and its side effects can pollute many miles beyond the operation. During the past year, New Zealand concern over the possible effects of the mining proposals has become acute. This was specially so in the areas of special environmental quality, such as the Coromandel, and here a very unhappy situation has arisen.

Jan 1, 1981

By Wemerson Junio Gandra

Para a redução do minério de ferro no alto-forno é necessária a utilização de uma fonte de carbono, que pode ser encontrada no carvão mineral e/ou carvão vegetal. Diante do cenário atual, a busca constante por maior competitividade, associada ao atendimento da qualidade e aos requisitos ambientais, exige a implementação de várias ações alternativas no processo de fabricação de gusa. Dentre elas, destaca-se a utilização de combustíveis alternativos no sistema de injeção dos altos-fornos, como por exemplo, a substituição parcial do carvão mineral pelo carvão vegetal. Do ponto de vista ambiental, é altamente favorável a utilização de uma fonte renovável de carbono. O objetivo desse trabalho é apresentar a adequação do processo, desde o recebimento do material até sua injeção nos altos-fornos, bem como os resultados já alcançados e os desafios futuros. A utilização do carvão vegetal na mistura de carvão pulverizado resulta em flexibilidade na utilização de matérias primas e contribui para preservação do meio ambiente.

Oct 30, 2017

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By K. M. Li, Y. D. Zhang

The selection of stripping dragline is a complicated problem. Several factors, such as the deposit buried conditions, the demand of mine production rate, cast blasting result, the mining/stripping operation method and parameters, etc. may comprehensively influence the optimal selection of technical specifications of the dragline. Under these circumstances, the basic thinking and procedures for dragline selection are put forward as follows. •Step 1—Initially estimate the dragline annual stripping rate and stripping bench height according to the annual coal production rate and advancing speed of mining front. Then the feasible alternatives of dragline sizes can be calculated and selected from the existing dragline series. •Step 2—A computer simulation model is developed to simulate the dragline stripping operation, to obtain a series of working face parameters, then to select the best dragline alternative. This step can be interactively iterated until the satisfactory results are obtained. •Step 3— Sensitivity analysis can be done with the systems simulation model by changing the stripping bench parameters, e.g. stripping bench height and cut width, etc. to verify and modify the selection results if necessary. The mathematical model for dragline stripping simulation has been set up. The flowchart of the model is shown. A case study for a large surface coal mine with annual production rate of 16 Mt/a is followed. The dragline bucket capacity and operation radius, stripping bench height and cut width as well as other parameters are comprehensively optimized and selected. Keywords: Open cast, dragline, specification, selection, cast blasting

Jan 1, 2003

By S Speed, N Corlis, A Goldstone, G N. Browne, M Fitzpatrick

In 2005, Solid Energy New Zealand Limited obtained non-notified consent for the disposal of 1Mt of coal ash at the Rotowaro minesite, forming part of a coal supply agreement with the Huntly Power Station. A non-notified resource consent was sought which necessitated that environmental effects be shown to be æless than minorÆ, and resulted from robust science and a pragmatic approach to design. As part of the assessment of environmental effects, there was a need to understand the effects of boron concentrations on aquatic organisms (ie algae, plankton, plants and invertebrates) in the receiving environment. Boron is a naturally occurring element that is found in the form of borates in the oceans, sedimentary rocks, coal, shale, and in some soils but Waikato coals and ashes have particularly high boron content. Boron is an essential micronutrient for higher plants with interspecies differences in the levels required for optimum growth. As aspects of the ANZECC (2000) derived boron limits are based on toxicity of aquatic algae and plants to boron it was important to assess these components in the environment. The effects on the receiving environment of the Awaroa Stream were assessed using predicted water chemistry and comparing actual boron concentrations in a comprehensive and multifaceted reference-condition approach of catchment ecological indicators. In addition a toxicological-based assessment of boron and a re-calculation of the ANZECC trigger levels were undertaken and applied to the ecological indicators. The reference-condition approach revealed that habitat and overall water quality attributes at and between sites was more influential in determining the aquatic biotic communities than boron concentrations alone. There was no evidence of any gradient of changes in ecological indicators with changing boron concentrations, nor evidence of any residual effect of high historic boron concentrations on the aquatic biota.

Jan 1, 2006

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

Study on Selective Reduction and Magnetic Separation of Low-Grade Nickel Laterite Ore to Produce High Nickel Concentrate

Sep 13, 2010

By Camilo José de Freitas Neto

O objetivo deste trabalho foi estudar a variabilidade do depósito de zinco sulfetado do projeto Ambrósia Sul, da Votorantim Metais localizado em Paracatu - Minas Gerais, frente aos processos de beneficiamento e poder, assim, detalhar o comportamento geometalúrgico dos vários corpos de minério do depósito. Além do estudo da variabilidade dos corpos de minério, o trabalho também inclui testes em escala de bancada durante anos e semestres de operação: 2016, 2017/01, 2017/02, 2018/01, 2018/02, 2019. A metodologia do estudo é resumida nas fases de amostragem de testemunho de sondagem, composição das amostras representativas dos corpos de minério e anos e semestres de operação da mina, testes de moagem, peneiramento, flotação de bancada e caracterização mineralógica da alimentação e produtos dos testes. O teste de bancada desenvolvido neste trabalho, tem como objetivo principal verificar variações significativas entre os corpos mineralizados e/ou semestres de mina de operação, tornando possível identificar potenciais oportunidades de otimização do circuito de tratamento de minérios, maximizando o retorno financeiro de toda a jazida mineral.

Aug 17, 2017

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou&apos; measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman&apos; calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay&apos; are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou&apos; and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil&apos; calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult&apos;s law within the requirements

Jan 1, 1957

By Michael J. Beus

This Bureau of Mines report describes field investigations conducted in the Coeur d&apos;Alene mining district of Idaho to obtain data on rock stress and physical properties. The resulting information has been utilized as input to detailed finite-element analyses to establish structural design criteria for deep-vein mine shafts. Measurement techniques include the Council for Scientific and Industrial Research biaxial and triaxial strain cells, the U.S. Geological Survey solid-inclusion probe, and the Colorado School of Mines dilatometer. Physical property testing was conducted in the laboratory on core obtained from each test site. Limited in situ physical property tests were also conducted. Reason-able success was obtained with the CSIR equipment, which was considered the most suitable for stress measurement in the study area. Test sites ranged in depth from 1,200 to 7,700 feet and are described in detail. The stress data were reduced by least-squares linear regression techniques to enable prediction of vertical and horizontal stresses to 7,500 feet. Ratios between the horizontal stresses as utilized for shaft design varied considerably, and a hydrostatic condition is the exception, based on Bureau measurements. Physical properties also varied widely, due to the complex geologic structure. Analyses of the data in terms of the tectonic history of the area show reasonable correlation. Data from previous rock mechanics investigations from the Coeur d&apos;Alene district were also compiled and presented as part of this report to justify any generalizations regarding stress conditions and physical properties of the district as a whole.

Jan 1, 1980

By Randall M. Wheeler

The purpose of this workshop is to illustrate how computer software can be used to evaluate blast design timing and simulate probable vibration characteristics. The workshop will be presented in two parts. Part I will cover the COMPU-BLAST Blast Design and Timing Analysis Program. Part II will focus on the ALPHA-BUST Vibration Analysis and Waveform Simulation Program. The information presented in the workshop will show how these two programs can be used together to help plan blast designs and aid in the control of vibration effects.

Jan 1, 1991

By C. D. Litton

This Bureau of Mines report presents a set of guidelines for determining the distribution of product-of-combustion fire sensors in underground mines. Sensor spacing is defined in terms of sensor alarm threshold, ventilation flow rate, and mine entry dimensions. Sensor spacing guidelines are presented for detection of fires from two primary combustibles, coal and wood, which are common to the majority of underground mines. The guidelines are based on data from full-scale and intermediate-scale fire tests conducted by the Bureau of Mines.

Jan 1, 1983

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

By N. Shariatmadari

In recent years, determining bearing capacity of piles from in-situ testing data as a complement of static and dynamic analysis has been used by geotechnical engineers. In this paper, different approaches for estimating base bearing capacity of piles from SPT data has been compared and evaluated. A new method for pile base bearing capacity in sand is proposed using SPT records. Data averaging, failure zone extension, and plunging failure of piles have been addressed in the proposed approach. A data bank comprising 10 full scale static load tests on instrumented piles and 26 dynamic tests, analyzed with signal matching technique by CAPWAP software, was used for validation. The SPT data that was performed close to pile locations is also included in the data base. Comparison of current methods by error investigation with Log-Normal approach demonstrates that the proposed method predicts pile base capacity with more accuracy and less scatter in comparison to other methods.

Jan 1, 2006